* Re: [PATCH v3 2/8] dt-bindings: gpio: cdns: add Axiado AX3005 GPIO variant
From: Swark Yang @ 2026-07-17 7:57 UTC (permalink / raw)
To: sashiko-reviews
Cc: linux-i3c, Alexandre Belloni, robh, Frank.Li, conor+dt,
devicetree
In-Reply-To: <20260717040056.6BA971F000E9@smtp.kernel.org>
On 7/17/2026 12:00 PM, sashiko-bot@kernel.org wrote:
> Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
> - [High] The schema enforces a 3-item compatible string chain that unintentionally forces AX3005 devices to inherit an AX3000-specific driver quirk, contradicting the commit message.
> --
Thanks for the report.
To clarify, the 3-item fallback in the code is intentional and correct.
The AX3005 GPIO block is fully compatible with the AX3000 implementation
and indeed requires the exact same driver quirks (such as the specific
direction mode and output enable handling).
The issue is just a poor description in my commit message. It should
have been worded as follows:
"Add binding for the Axiado AX3005 GPIO controller. The AX3005 GPIO
block is fully compatible with the AX3000 implementation and requires
the same driver quirks. Therefore, it is added with a fallback to the
'axiado,ax3000-gpio' compatible string, which in turn falls back to the
generic 'cdns,gpio-r1p02'."
I will hold off on sending a v4 just for this commit message update to
avoid unnecessary noise on the list. I'll wait for further review
comments on the rest of the series and will include this updated message
if a v4 re-roll is needed.
Best Regards,
Swark
^ permalink raw reply
* Re: [PATCH 0/3] Add AD5710R/AD5711R DAC
From: Kim Seer Paller @ 2026-07-17 7:50 UTC (permalink / raw)
To: Andy Shevchenko
Cc: Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko,
Michael Hennerich, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Philipp Zabel, linux-iio, linux-kernel, linux, devicetree
In-Reply-To: <alkbtNdOe__XP7ud@ashevche-desk.local>
On Fri Jul 17, 2026 at 1:58 AM PST, Andy Shevchenko wrote:
> On Thu, Jul 16, 2026 at 03:59:24PM +0800, Kim Seer Paller wrote:
> > The AD5710R (16-bit) and AD5711R (12-bit) are 8-channel, low-power,
> > configurable current/voltage output DACs with an on-chip 2.5V reference.
> > Each channel can be independently configured as a voltage output
> > (0V to VREF or 0V to 2xVREF) or a current output (0mA to 50mA).
> >
> > This series adds support for these parts:
> > - ABI documentation for the high_z powerdown mode and the current-output
> > powerdown attributes
> > - device tree bindings for the AD5710R/AD5711R
> > - basic IIO DAC driver, supporting per-channel voltage/current output
> > selection, per-channel powerdown, software or hardware (LDAC) DAC
> > updates, optional output range doubling, internal or external
> > reference, and hardware reset (with a software-reset fallback).
>
> Why a brand new driver?
After looking more closely, the register map is the same as the AD3530R family.
I originally kept it separate because of the functional differences: per channel
VDAC/IDAC selection described in device tree via adi,ch-func, selectable 12/16 bit
resolution, and current output path. But those can be fit the existing chip_info
abstraction. Given that, I'm leaning toward extending ad3530r to support the
ad5710r/ad5711r and dropping the standalone driver. Does that direction work for
you? If so, I will do it in v2.
>
> > Datasheet:
> > https://www.analog.com/media/en/technical-documentation/data-sheets/ad5711r-ad5710r.pdf
>
> --
> With Best Regards,
> Andy Shevchenko
^ permalink raw reply
* [PATCH 3/3] spi: amlogic: spisg: Add support for A9 controller features
From: Xianwei Zhao via B4 Relay @ 2026-07-17 7:49 UTC (permalink / raw)
To: Sunny Luo, Mark Brown, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-amlogic, linux-spi, devicetree, linux-kernel, Xianwei Zhao
In-Reply-To: <20260717-a9-spisg-v1-0-2eeea77be19f@amlogic.com>
From: Xianwei Zhao <xianwei.zhao@amlogic.com>
The Amlogic A9 SPISG controller extends the A4 controller with additional
configuration options, including:
- Extended CS setup timing
- Hardware-controlled CS hold timing
- MOSI idle output configuration
- Configurable word gap
Add SoC-specific capability data and configure these features when they
are supported by the underlying hardware while keeping compatibility with
existing A4 controllers.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
---
drivers/spi/spi-amlogic-spisg.c | 65 ++++++++++++++++++++++++++++++++++++++---
1 file changed, 61 insertions(+), 4 deletions(-)
diff --git a/drivers/spi/spi-amlogic-spisg.c b/drivers/spi/spi-amlogic-spisg.c
index 0f026d3e43e0..845eb81d483a 100644
--- a/drivers/spi/spi-amlogic-spisg.c
+++ b/drivers/spi/spi-amlogic-spisg.c
@@ -37,6 +37,12 @@
#define CFG_HW_POS BIT(6)
/* start on vsync falling */
#define CFG_HW_NEG BIT(7)
+#define CFG_WORD_GAP GENMASK(9, 8)
+#define CFG_MO_IDLE_OUTPUT GENMASK(11, 10)
+/* cs hold time in pclk */
+#define CFG_CS_HOLD GENMASK(26, 12)
+/* high 4 bits of cs setup time in sclk */
+#define CFG_CS_SETUP_EXTEND GENMASK(30, 27)
#define SPISG_REG_CFG_START 0x08
#define CFG_BLOCK_NUM GENMASK(19, 0)
@@ -143,6 +149,13 @@ struct spisg_descriptor_extra {
int rx_ccsg_len;
};
+struct aml_spisg_data {
+ bool mo_idle_output_ctrl;
+ bool word_gap_ctrl;
+ bool cs_hold_ctrl;
+ bool cs_setup_extend_ctrl;
+};
+
struct spisg_device {
struct spi_controller *controller;
struct platform_device *pdev;
@@ -152,6 +165,7 @@ struct spisg_device {
struct clk *sclk;
struct clk_div_table *tbl;
struct completion completion;
+ const struct aml_spisg_data *data;
u32 status;
u32 speed_hz;
u32 effective_speed_hz;
@@ -483,6 +497,7 @@ static int aml_spisg_transfer_one_message(struct spi_controller *ctlr,
{
struct spisg_device *spisg = spi_controller_get_devdata(ctlr);
struct device *dev = &spisg->pdev->dev;
+ const struct aml_spisg_data *data = spisg->data;
unsigned long long ms = 0;
struct spi_transfer *xfer;
struct spisg_descriptor *descs, *desc;
@@ -491,6 +506,7 @@ static int aml_spisg_transfer_one_message(struct spi_controller *ctlr,
int desc_num = 1, descs_len;
bool last_xfer_keep_ss = false;
u32 cs_hold_in_sclk = 0;
+ u32 val;
int ret = -EIO;
if (!aml_spisg_sem_down_read(spisg)) {
@@ -525,9 +541,17 @@ static int aml_spisg_transfer_one_message(struct spi_controller *ctlr,
}
/* calculate cs-setup delay with the first xfer speed */
- if (list_is_first(&xfer->transfer_list, &msg->transfers))
- desc->cfg_bus |= FIELD_PREP(CFG_CS_SETUP,
- spi_delay_to_sclk(xfer->effective_speed_hz, &msg->spi->cs_setup));
+ if (list_is_first(&xfer->transfer_list, &msg->transfers)) {
+ val = spi_delay_to_sclk(xfer->effective_speed_hz, &msg->spi->cs_setup);
+ if (data && data->cs_setup_extend_ctrl) {
+ val = min_t(u32, 0xFF, val);
+ desc->cfg_bus |= FIELD_PREP(CFG_CS_SETUP, val & 0xF);
+ FIELD_MODIFY(CFG_CS_SETUP_EXTEND, &spisg->cfg_spi, val >> 4);
+ } else {
+ val = min_t(u32, 0xF, val);
+ desc->cfg_bus |= FIELD_PREP(CFG_CS_SETUP, val);
+ }
+ }
/* calculate cs-hold delay with the last xfer speed */
if (list_is_last(&xfer->transfer_list, &msg->transfers)) {
@@ -542,7 +566,12 @@ static int aml_spisg_transfer_one_message(struct spi_controller *ctlr,
xfer->effective_speed_hz);
}
- if (cs_hold_in_sclk) {
+ if (data && data->cs_hold_ctrl) {
+ cs_hold_in_sclk = cs_hold_in_sclk ? : 1;
+ val = cs_hold_in_sclk * (FIELD_GET(CFG_CLK_DIV, spisg->cfg_bus) + 1);
+ FIELD_MODIFY(CFG_CS_HOLD, &spisg->cfg_spi, val);
+ desc--;
+ } else if (cs_hold_in_sclk) {
/* additional null-descriptor to achieve the cs-hold delay */
aml_spisg_setup_null_desc(spisg, desc, cs_hold_in_sclk);
desc--;
@@ -722,6 +751,7 @@ static int aml_spisg_probe(struct platform_device *pdev)
struct spisg_device *spisg;
struct device *dev = &pdev->dev;
void __iomem *base;
+ u32 val = 0;
int ret, irq;
const struct regmap_config aml_regmap_config = {
@@ -740,6 +770,7 @@ static int aml_spisg_probe(struct platform_device *pdev)
spisg = spi_controller_get_devdata(ctlr);
spisg->controller = ctlr;
+ spisg->data = (struct aml_spisg_data *)of_device_get_match_data(dev);
spisg->pdev = pdev;
platform_set_drvdata(pdev, spisg);
@@ -770,6 +801,21 @@ static int aml_spisg_probe(struct platform_device *pdev)
spisg->cfg_spi = FIELD_PREP(CFG_SFLASH_WP, 1) |
FIELD_PREP(CFG_SFLASH_HD, 1);
+
+ if (spisg->data && spisg->data->mo_idle_output_ctrl) {
+ if (!of_property_read_u32(dev->of_node, "amlogic,mo-idle-output", &val))
+ spisg->cfg_spi |= FIELD_PREP(CFG_MO_IDLE_OUTPUT, val);
+ else
+ spisg->cfg_spi |= FIELD_PREP(CFG_MO_IDLE_OUTPUT, 0);
+ }
+
+ if (spisg->data && spisg->data->word_gap_ctrl) {
+ if (!of_property_read_u32(dev->of_node, "amlogic,word-gap", &val))
+ spisg->cfg_spi |= FIELD_PREP(CFG_WORD_GAP, val);
+ else
+ spisg->cfg_spi |= FIELD_PREP(CFG_WORD_GAP, 1);
+ }
+
if (spi_controller_is_target(ctlr)) {
spisg->cfg_spi |= FIELD_PREP(CFG_SLAVE_EN, 1);
spisg->cfg_bus = FIELD_PREP(CFG_TX_TUNING, 0xf);
@@ -856,6 +902,13 @@ static int spisg_resume_runtime(struct device *dev)
return 0;
}
+static const struct aml_spisg_data a9_spisg_data = {
+ .mo_idle_output_ctrl = true,
+ .word_gap_ctrl = true,
+ .cs_hold_ctrl = true,
+ .cs_setup_extend_ctrl = true,
+};
+
static const struct dev_pm_ops amlogic_spisg_pm_ops = {
.runtime_suspend = spisg_suspend_runtime,
.runtime_resume = spisg_resume_runtime,
@@ -865,6 +918,10 @@ static const struct of_device_id amlogic_spisg_of_match[] = {
{
.compatible = "amlogic,a4-spisg",
},
+ {
+ .compatible = "amlogic,a9-spisg",
+ .data = &a9_spisg_data,
+ },
{ /* sentinel */ }
};
--
2.52.0
^ permalink raw reply related
* [PATCH 2/3] spi: amlogic: spisg: Fix the incorrect keep_ss of the last descriptor
From: Xianwei Zhao via B4 Relay @ 2026-07-17 7:49 UTC (permalink / raw)
To: Sunny Luo, Mark Brown, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-amlogic, linux-spi, devicetree, linux-kernel, Xianwei Zhao
In-Reply-To: <20260717-a9-spisg-v1-0-2eeea77be19f@amlogic.com>
From: Sunny Luo <sunny.luo@amlogic.com>
The driver currently unconditionally clears CFG_KEEP_SS on the last
descriptor, causing the last transfer's cs_change setting to be ignored.
Record the cs_change value of the last SPI transfer and use it to
program CFG_KEEP_SS on the final descriptor. When a null descriptor is
inserted to implement the cs-hold delay, keep CFG_KEEP_SS set on the
preceding transfer descriptor and apply the recorded value to the final
descriptor instead.
This ensures the controller handles chip select correctly for the last
transfer regardless of whether a cs-hold delay is required.
Fixes: cef9991e04ae ("spi: Add Amlogic SPISG driver")
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
---
drivers/spi/spi-amlogic-spisg.c | 15 +++++++++++----
1 file changed, 11 insertions(+), 4 deletions(-)
diff --git a/drivers/spi/spi-amlogic-spisg.c b/drivers/spi/spi-amlogic-spisg.c
index afc8af04638d..0f026d3e43e0 100644
--- a/drivers/spi/spi-amlogic-spisg.c
+++ b/drivers/spi/spi-amlogic-spisg.c
@@ -489,6 +489,7 @@ static int aml_spisg_transfer_one_message(struct spi_controller *ctlr,
struct spisg_descriptor_extra *exdescs, *exdesc;
dma_addr_t descs_paddr;
int desc_num = 1, descs_len;
+ bool last_xfer_keep_ss = false;
u32 cs_hold_in_sclk = 0;
int ret = -EIO;
@@ -529,9 +530,11 @@ static int aml_spisg_transfer_one_message(struct spi_controller *ctlr,
spi_delay_to_sclk(xfer->effective_speed_hz, &msg->spi->cs_setup));
/* calculate cs-hold delay with the last xfer speed */
- if (list_is_last(&xfer->transfer_list, &msg->transfers))
+ if (list_is_last(&xfer->transfer_list, &msg->transfers)) {
cs_hold_in_sclk =
spi_delay_to_sclk(xfer->effective_speed_hz, &msg->spi->cs_hold);
+ last_xfer_keep_ss = xfer->cs_change;
+ }
desc++;
exdesc++;
@@ -539,13 +542,17 @@ static int aml_spisg_transfer_one_message(struct spi_controller *ctlr,
xfer->effective_speed_hz);
}
- if (cs_hold_in_sclk)
+ if (cs_hold_in_sclk) {
/* additional null-descriptor to achieve the cs-hold delay */
aml_spisg_setup_null_desc(spisg, desc, cs_hold_in_sclk);
- else
desc--;
+ desc->cfg_bus |= FIELD_PREP(CFG_KEEP_SS, 1);
+ desc++;
+ } else {
+ desc--;
+ }
- desc->cfg_bus |= FIELD_PREP(CFG_KEEP_SS, 0);
+ FIELD_MODIFY(CFG_KEEP_SS, &desc->cfg_bus, last_xfer_keep_ss);
desc->cfg_start |= FIELD_PREP(CFG_EOC, 1);
/* some tolerances */
--
2.52.0
^ permalink raw reply related
* [PATCH 0/3] spi: add support for Amlogic A9
From: Xianwei Zhao via B4 Relay @ 2026-07-17 7:49 UTC (permalink / raw)
To: Sunny Luo, Mark Brown, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-amlogic, linux-spi, devicetree, linux-kernel, Xianwei Zhao
Add bindings for A9 with some features, and driver for A9 base on A4.
Fix the incorrect keep_ss of the last descriptor.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
---
Sunny Luo (1):
spi: amlogic: spisg: Fix the incorrect keep_ss of the last descriptor
Xianwei Zhao (2):
spi: dt-bindings: amlogic: spisg: Document A9-specific properties
spi: amlogic: spisg: Add support for A9 controller features
.../devicetree/bindings/spi/amlogic,a4-spisg.yaml | 36 ++++++++--
drivers/spi/spi-amlogic-spisg.c | 78 ++++++++++++++++++++--
2 files changed, 103 insertions(+), 11 deletions(-)
---
base-commit: d0b5dd16226814e5c73ba8daf88d3d91c990a38f
change-id: 20260715-a9-spisg-f19ce0403a50
Best regards,
--
Xianwei Zhao <xianwei.zhao@amlogic.com>
^ permalink raw reply
* [PATCH 1/3] spi: dt-bindings: amlogic: spisg: Document A9-specific properties
From: Xianwei Zhao via B4 Relay @ 2026-07-17 7:49 UTC (permalink / raw)
To: Sunny Luo, Mark Brown, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-amlogic, linux-spi, devicetree, linux-kernel, Xianwei Zhao
In-Reply-To: <20260717-a9-spisg-v1-0-2eeea77be19f@amlogic.com>
From: Xianwei Zhao <xianwei.zhao@amlogic.com>
Document the Amlogic A9 SPISG controller and its additional
Device Tree properties.
Add the "amlogic,a9-spisg" compatible string and define the
A9-specific "amlogic,mo-idle-output" and "amlogic,word-gap"
properties, which configure the MOSI idle output level and
the inter-word gap, respectively.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
---
.../devicetree/bindings/spi/amlogic,a4-spisg.yaml | 36 +++++++++++++++++++---
1 file changed, 32 insertions(+), 4 deletions(-)
diff --git a/Documentation/devicetree/bindings/spi/amlogic,a4-spisg.yaml b/Documentation/devicetree/bindings/spi/amlogic,a4-spisg.yaml
index 9bfb8089f7ea..7efdc748d566 100644
--- a/Documentation/devicetree/bindings/spi/amlogic,a4-spisg.yaml
+++ b/Documentation/devicetree/bindings/spi/amlogic,a4-spisg.yaml
@@ -11,12 +11,11 @@ maintainers:
- Xianwei Zhao <xianwei.zhao@amlogic.com>
- Sunny Luo <sunny.luo@amlogic.com>
-allOf:
- - $ref: spi-controller.yaml#
-
properties:
compatible:
- const: amlogic,a4-spisg
+ enum:
+ - amlogic,a4-spisg
+ - amlogic,a9-spisg
reg:
maxItems: 1
@@ -42,6 +41,35 @@ required:
- clocks
- clock-names
+allOf:
+ - $ref: spi-controller.yaml#
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - amlogic,a9-spisg
+ then:
+ properties:
+ amlogic,mo-idle-output:
+ description: |
+ Controls the MOSI output level when the controller is idle.
+
+ 0 - Drive MOSI low
+ 1 - Drive MOSI high
+ 2 - Follow the last transmitted bit
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
+ default: 0
+
+ amlogic,word-gap:
+ description: |
+ Number of idle clock cycles inserted between consecutive SPI
+ words.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 1
+
unevaluatedProperties: false
examples:
--
2.52.0
^ permalink raw reply related
* Re: [PATCH v3 6/7] clk: Add support for clock nexus dt bindings
From: Miquel Raynal @ 2026-07-17 7:43 UTC (permalink / raw)
To: sashiko-bot; +Cc: sashiko-reviews, devicetree, robh, conor+dt
In-Reply-To: <20260716113708.9CED11F000E9@smtp.kernel.org>
On 16/07/2026 at 11:37:08 GMT, sashiko-bot@kernel.org wrote:
> Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
>
> Pre-existing issues:
> - [High] Unconditional dereference of optional `out_args` pointer in
> `of_parse_phandle_with_args_map()`.
This issue has been addressed in another thread:
https://lore.kernel.org/linux-devicetree/20260716-schneider-v7-2-rc1-eip-of-fix-v1-1-9b9383f936c6@bootlin.com/T/#u
^ permalink raw reply
* Re: [PATCH v3 2/7] clk: tests: Add clk_parse_clkspec() Kunit testing
From: Miquel Raynal @ 2026-07-17 7:42 UTC (permalink / raw)
To: sashiko-bot; +Cc: sashiko-reviews, conor+dt, devicetree, robh
In-Reply-To: <20260716110432.03D171F000E9@smtp.kernel.org>
On 16/07/2026 at 11:04:31 GMT, sashiko-bot@kernel.org wrote:
> Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
>
> Pre-existing issues:
> - [High] Pre-existing race condition in `__of_clk_get()` exposing a
> time-of-check to time-of-use (TOCTOU) use-after-free vulnerability
> during concurrent clock provider unregistration.
After looking into this issue, I don't see any relationship with this
series, it is probably worth keeping in mind, but since we are exposing
the symbol for kunit testing which is just not racy by any mean with
something else, I believe it is not worth the investigation.
Thanks,
Miquèl
^ permalink raw reply
* Re: [PATCH v4 3/3] input: misc: Add Qualcomm SPMI PMIC haptics driver
From: sashiko-bot @ 2026-07-17 7:42 UTC (permalink / raw)
To: Fenglin Wu; +Cc: conor+dt, devicetree, robh, linux-input, dmitry.torokhov
In-Reply-To: <20260717-qcom-spmi-haptics-v4-3-b0fe0ed30849@oss.qualcomm.com>
Thank you for your contribution! Sashiko AI review found 4 potential issue(s) to consider:
- [High] Missing stop logic in the haptics worker causes indefinite playback and PM reference leak when effect duration expires.
- [Medium] Explicit input_unregister_device() on a devm-managed device violates input subsystem rules.
- [Medium] Data race on `irq_enabled` causes permanently unbalanced IRQ disable depth on bus errors.
- [Low] Use of undefined macro `kmalloc_obj` causes compilation failure.
--
--- Patch [3]: [PATCH v4 3/3] input: misc: Add Qualcomm SPMI PMIC haptics driver ---
commit e63f14da39f2a372d48e418f9fac8b20cd9d0698
Author: Fenglin Wu <fenglin.wu@oss.qualcomm.com>
input: misc: Add Qualcomm SPMI PMIC haptics driver
Adds an initial driver for the Qualcomm PMIH0108 PMIC haptics module.
Supports DIRECT_PLAY and FIFO modes via the input force-feedback framework.
> diff --git a/drivers/input/misc/qcom-spmi-haptics.c b/drivers/input/misc/qcom-spmi-haptics.c
> new file mode 100644
> index 0000000000000..235f77e0229c5
> --- /dev/null
> +++ b/drivers/input/misc/qcom-spmi-haptics.c
[ ... ]
> +static int haptics_enqueue_play_req(struct qcom_haptics *h, int effect_id, bool play)
> +{
> + struct haptics_play_req *req;
> +
> + guard(spinlock_irqsave)(&h->play_queue_lock);
> +
> + /*
> + * Coalesce with an already queued request for
> + * the same effect instead of appending.
> + */
> + list_for_each_entry(req, &h->play_queue, node) {
> + if (req->effect_id == effect_id) {
> + req->play = play;
> + return 0;
> + }
> + }
> +
> + req = kmalloc_obj(*req, GFP_ATOMIC);
> + if (!req)
> + return -ENOMEM;
[Severity: Low]
Does this code compile successfully? I couldn't find kmalloc_obj() defined in
the standard kernel headers. Should this use kmalloc() or kzalloc() instead?
> +
> + req->effect_id = effect_id;
> + req->play = play;
[ ... ]
> +static irqreturn_t haptics_fifo_empty_irq(int irq, void *dev_id)
> +{
[ ... ]
> + /* Refill: write the next chunk */
> + to_write = min_t(u32, h->data_len - h->data_written,
> + h->fifo_len - FIFO_EMPTY_THRESH);
> + ret = haptics_write_fifo_chunk(h, &h->fifo_data[h->data_written], to_write);
> + if (ret) {
> + dev_err(h->dev, "refill FIFO samples failed, ret=%d\n", ret);
> + /*
> + * If data refilling is failed,stop the HW play and disable the
> + * IRQ to prevent the FIFO empty IRQ being fired continuously.
> + */
> + cfg_write(h, HAP_CFG_SPMI_PLAY_REG, 0);
> + disable_irq_nosync(h->fifo_empty_irq);
> + h->irq_enabled = false;
[Severity: Medium]
Can a data race occur on h->irq_enabled here?
If userspace stops playback concurrently with a bus write failure in
haptics_fifo_empty_irq(), both paths could check and modify h->irq_enabled
without mutual exclusion.
For example, this path:
haptics_fifo_empty_irq()
disable_irq_nosync(h->fifo_empty_irq);
h->irq_enabled = false;
Could race with:
haptics_stop_locked()
haptics_fifo_irq_enable(h, false);
This might result in disable_irq() being called twice while enable_irq() is
only called once, leaving the IRQ permanently disabled and breaking future
FIFO playback.
> + return IRQ_HANDLED;
> + }
> +
> + h->data_written += to_write;
[ ... ]
> +static void haptics_play_work(struct work_struct *work)
> +{
> + struct qcom_haptics *h = container_of(to_delayed_work(work),
> + struct qcom_haptics, play_work);
> + struct haptics_play_req *req = haptics_dequeue_play_req(h);
> + bool rearmed = false;
> + u32 length_us;
> + int ret;
> +
> + guard(mutex)(&h->play_lock);
> +
> + /* No valid request available */
> + if (req == NULL)
> + return;
[Severity: High]
When a finite-length effect expires, schedule_delayed_work() wakes up this
worker, but haptics_dequeue_play_req() returns NULL since the queue is
empty.
Since we return early here when req is NULL, how does the driver stop the
active effect and release the runtime PM reference? This appears to leave
the device vibrating indefinitely.
> +
> + if (req->play) {
> + ret = haptics_start_locked(h, req->effect_id);
[ ... ]
> +static void qcom_haptics_remove(struct platform_device *pdev)
> +{
> + struct qcom_haptics *h = platform_get_drvdata(pdev);
> +
> + /*
> + * Unregister the input device explicitly at the beginning
> + * to avoid the input device being used after the resources
> + * are freed.
> + */
> + input_unregister_device(h->input);
[Severity: Medium]
Is it safe to explicitly unregister this input device here?
The input device is allocated with devm_input_allocate_device() during
probe, which means the input core will automatically handle unregistration
when the provider device is unbound.
Manually calling input_unregister_device() on a devm-managed device can
lead to double-unregistration.
> + disable_delayed_work_sync(&h->play_work);
> + scoped_guard(mutex, &h->play_lock) {
> + haptics_queue_flush(h);
> + haptics_stop_locked(h, true);
> + }
> +
> + haptics_enable_module(h, false);
--
Sashiko AI review · https://sashiko.dev/#/patchset/20260717-qcom-spmi-haptics-v4-0-b0fe0ed30849@oss.qualcomm.com?part=3
^ permalink raw reply
* Re: [PATCH 3/3] clk: spacemit: k3: fix missing /2 factor in i2s sysclk dividers
From: sashiko-bot @ 2026-07-17 7:37 UTC (permalink / raw)
To: Troy Mitchell; +Cc: robh, conor+dt, devicetree
In-Reply-To: <20260717-k3-clk-fix-i2s-v1-3-e95001a692ee@linux.spacemit.com>
Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
New issues:
- [Medium] The commit message mathematically contradicts the driver's actual hardware implementation.
Pre-existing issues:
- [High] Kernel panic due to unhandled zero divisor (`num`) in clock rate calculations.
--
--- Patch [3]: [PATCH 3/3] clk: spacemit: k3: fix missing /2 factor in i2s sysclk dividers ---
commit f6d65354cd50f2c66ffa439212d0df739e8b5882
Author: Troy Mitchell <troy.mitchell@linux.spacemit.com>
clk: spacemit: k3: fix missing /2 factor in i2s sysclk dividers
This commit updates the i2s sysclk dividers in the spacemit k3 clock driver to
set pre_div to 2. This accounts for a fixed 1/2 hardware divider after the
configurable divider.
> The i2s{0,2,3,4,5}_sysclk_div DDNs have an additional fixed 1/2
> divider in the hardware IP after the configurable divider, so the
> real output rate is:
>
> rate = parent_rate * num / (den * 2)
[Severity: Medium]
Does this formula mathematically contradict the driver's implementation?
The code in drivers/clk/spacemit/ccu_ddn.c calculates the rate by multiplying
by den and dividing by num:
drivers/clk/spacemit/ccu_ddn.c:ccu_ddn_calc_rate() {
...
return prate * den / pre_div / num;
...
}
The file's documentation also notes:
* Fin denominator
* Fout = ----- * -------------
* 2 numerator
Could the commit message be updated to reflect the actual hardware behavior?
> Set pre_div to 2 to account for it.
>
> Fixes: e371a77255b8 ("clk: spacemit: k3: add the clock tree")
> Signed-off-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
>
> ---
> drivers/clk/spacemit/ccu-k3.c | 10 +++++-----
> 1 file changed, 5 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/clk/spacemit/ccu-k3.c b/drivers/clk/spacemit/ccu-k3.c
> index abcc5caa67bd7..675cf03d98f05 100644
> --- a/drivers/clk/spacemit/ccu-k3.c
> +++ b/drivers/clk/spacemit/ccu-k3.c
> @@ -244,11 +244,11 @@ CCU_MUX_DEFINE(i2s3_sysclk_sel, i2s_sysclk_parents, MPMU_I2S_SYSCLK_CTRL, 12, 2,
> CCU_MUX_DEFINE(i2s4_sysclk_sel, i2s_sysclk_parents, MPMU_I2S_SYSCLK_CTRL, 16, 2, 0);
> CCU_MUX_DEFINE(i2s5_sysclk_sel, i2s_sysclk_parents, MPMU_I2S_SYSCLK_CTRL, 20, 2, 0);
>
> -CCU_DDN_DEFINE(i2s0_sysclk_div, i2s0_sysclk_sel, MPMU_I2S0_SYSCLK, 0, 16, 16, 16, 1, 0);
> -CCU_DDN_DEFINE(i2s2_sysclk_div, i2s2_sysclk_sel, MPMU_I2S2_SYSCLK, 0, 16, 16, 16, 1, 0);
> -CCU_DDN_DEFINE(i2s3_sysclk_div, i2s3_sysclk_sel, MPMU_I2S3_SYSCLK, 0, 16, 16, 16, 1, 0);
> -CCU_DDN_DEFINE(i2s4_sysclk_div, i2s4_sysclk_sel, MPMU_I2S4_SYSCLK, 0, 16, 16, 16, 1, 0);
> -CCU_DDN_DEFINE(i2s5_sysclk_div, i2s5_sysclk_sel, MPMU_I2S5_SYSCLK, 0, 16, 16, 16, 1, 0);
> +CCU_DDN_DEFINE(i2s0_sysclk_div, i2s0_sysclk_sel, MPMU_I2S0_SYSCLK, 0, 16, 16, 16, 2, 0);
[Severity: High]
This is a pre-existing issue, but can this lead to a kernel panic due to an
unhandled zero divisor?
In drivers/clk/spacemit/ccu_ddn.c, ccu_ddn_recalc_rate() reads hardware
registers directly:
drivers/clk/spacemit/ccu_ddn.c:ccu_ddn_recalc_rate() {
...
num = (val & ddn->num_mask) >> ddn->num_shift;
den = (val & ddn->den_mask) >> ddn->den_shift;
return ccu_ddn_calc_rate(prate, num, den, ddn->pre_div);
...
}
If the register contains 0 for num, ccu_ddn_calc_rate() will divide by zero:
drivers/clk/spacemit/ccu_ddn.c:ccu_ddn_calc_rate() {
...
return prate * den / pre_div / num;
...
}
Additionally, in ccu_ddn_calc_best_rate(), if the parent rate is less than
ddn->pre_div (for example, if prate is 0), the calculation
prate / ddn->pre_div evaluates to 0. This causes rational_best_approximation()
to set num to 0, which is then passed to ccu_ddn_calc_rate(), again leading to
a division by zero.
Should we add validation to prevent division by zero in these paths?
> +CCU_DDN_DEFINE(i2s2_sysclk_div, i2s2_sysclk_sel, MPMU_I2S2_SYSCLK, 0, 16, 16, 16, 2, 0);
> +CCU_DDN_DEFINE(i2s3_sysclk_div, i2s3_sysclk_sel, MPMU_I2S3_SYSCLK, 0, 16, 16, 16, 2, 0);
> +CCU_DDN_DEFINE(i2s4_sysclk_div, i2s4_sysclk_sel, MPMU_I2S4_SYSCLK, 0, 16, 16, 16, 2, 0);
> +CCU_DDN_DEFINE(i2s5_sysclk_div, i2s5_sysclk_sel, MPMU_I2S5_SYSCLK, 0, 16, 16, 16, 2, 0);
>
> static const struct clk_parent_data i2s2_sysclk_parents[] = {
> CCU_PARENT_HW(i2s_sysclk),
--
Sashiko AI review · https://sashiko.dev/#/patchset/20260717-k3-clk-fix-i2s-v1-0-e95001a692ee@linux.spacemit.com?part=3
^ permalink raw reply
* Re: [PATCH] dt-bindings: remoteproc: qcom,sm8550-pas: Add Hawi and Maili MPSS compatible
From: Yijie Yang @ 2026-07-17 7:36 UTC (permalink / raw)
To: Mukesh Ojha, Bjorn Andersson, Mathieu Poirier, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Manivannan Sadhasivam
Cc: linux-arm-msm, linux-remoteproc, devicetree, linux-kernel
In-Reply-To: <20260713093237.691117-1-mukesh.ojha@oss.qualcomm.com>
On 7/13/2026 5:32 PM, Mukesh Ojha wrote:
> Document compatible string for the MPSS Peripheral Authentication
> Service on the Hawi and Maili SoCs. The Hawi and Maili MPSS is
> compatible with the SM8650 MPSS (six interrupts, CX and MSS power
> domains, memory region).
>
> Signed-off-by: Mukesh Ojha <mukesh.ojha@oss.qualcomm.com>
> ---
> .../devicetree/bindings/remoteproc/qcom,sm8550-pas.yaml | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,sm8550-pas.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,sm8550-pas.yaml
> index faf7b2890de8..0d9fd1598b5b 100644
> --- a/Documentation/devicetree/bindings/remoteproc/qcom,sm8550-pas.yaml
> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,sm8550-pas.yaml
> @@ -17,6 +17,8 @@ properties:
> compatible:
> oneOf:
> - enum:
> + - qcom,hawi-mpss-pas
> + - qcom,maili-mpss-pas
> - qcom,sdx75-mpss-pas
> - qcom,sm8550-adsp-pas
> - qcom,sm8550-cdsp-pas
> @@ -196,6 +198,8 @@ allOf:
> properties:
> compatible:
> enum:
> + - qcom,hawi-mpss-pas
> + - qcom,maili-mpss-pas
> - qcom,sdx75-mpss-pas
> - qcom,sm8650-mpss-pas
> then:
> @@ -246,6 +250,8 @@ allOf:
> properties:
> compatible:
> enum:
> + - qcom,hawi-mpss-pas
> + - qcom,maili-mpss-pas
> - qcom,sdx75-mpss-pas
> - qcom,sm8550-mpss-pas
> - qcom,sm8650-mpss-pas
IMO, both should fall back to sm8650.
--
Best Regards,
Yijie
^ permalink raw reply
* Re: [PATCH v4 12/12] arm64: dts: rockchip: add support for NanoPi M6 board
From: sashiko-bot @ 2026-07-17 7:35 UTC (permalink / raw)
To: Joachim Eastwood; +Cc: robh, conor+dt, devicetree
In-Reply-To: <20260717-nanopi-m6-v4-12-b31391a72e41@gmail.com>
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Low] Unused OF-graph `port` and `endpoint` nodes are defined inside `rt5616` and `i2s0_8ch`, but they are ignored by the selected sound card driver.
--
--- Patch [12]: [PATCH v4 12/12] arm64: dts: rockchip: add support for NanoPi M6 board ---
commit f3f11c960b7a0aba3e85b29f5c9f9229eadc9524
Author: Joachim Eastwood <joachim.eastwood@gmail.com>
arm64: dts: rockchip: add support for NanoPi M6 board
This commit adds device tree support for the FriendlyElec NanoPi M6 board,
which shares most features with the R6 boards but includes M.2 PCIe slots,
an additional USB 2.0 port, and an RT5616 audio CODEC.
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-m6v1.dts b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-m6v1.dts
> new file mode 100644
> index 0000000000000..f981973c96ac0
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-m6v1.dts
> @@ -0,0 +1,67 @@
[ ... ]
> + sound {
> + compatible = "simple-audio-card";
[ ... ]
> + simple-audio-card,cpu {
> + sound-dai = <&i2s0_8ch>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&rt5616>;
> + };
> + };
> +};
> +
> +&i2c7 {
> + rt5616: codec@1b {
> + compatible = "realtek,rt5616";
> + reg = <0x1b>;
> + clocks = <&cru I2S0_8CH_MCLKOUT_TO_IO>;
> + clock-names = "mclk";
> + #sound-dai-cells = <0>;
> + assigned-clocks = <&cru I2S0_8CH_MCLKOUT_TO_IO>;
> + assigned-clock-rates = <12288000>;
> +
> + port {
> + rt5616_p0: endpoint {
> + remote-endpoint = <&i2s0_8ch_p0>;
> + };
> + };
> + };
> +};
> +
> +&i2s0_8ch {
> + port {
> + i2s0_8ch_p0: endpoint {
> + dai-format = "i2s";
> + mclk-fs = <256>;
> + remote-endpoint = <&rt5616_p0>;
> + };
> + };
> +};
[Severity: Low]
Are these OF-graph port and endpoint nodes needed in rt5616 and i2s0_8ch?
Since the sound card uses simple-audio-card with sound-dai phandles to
establish the DAI links, neither simple-audio-card nor the rockchip i2s
driver will parse the ALSA OF-graph routing or properties like mclk-fs
embedded inside these endpoints.
These nodes are typically meant for audio-graph-card, so they appear to be
unused device tree bloat in this configuration.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20260717-nanopi-m6-v4-0-b31391a72e41@gmail.com?part=12
^ permalink raw reply
* Re: [PATCH 1/3] dt-bindings: soc: spacemit: k3: add i2s_sysclk, i2s_bclk_factor and i2s1_sysclk_src IDs
From: sashiko-bot @ 2026-07-17 7:33 UTC (permalink / raw)
To: Troy Mitchell; +Cc: robh, conor+dt, devicetree
In-Reply-To: <20260717-k3-clk-fix-i2s-v1-1-e95001a692ee@linux.spacemit.com>
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] The commit message incorrectly claims that CLK_MPMU_I2S1_SYSCLK keeps its existing ID of 47, when its actual ID is 34.
--
--- Patch [1]: [PATCH 1/3] dt-bindings: soc: spacemit: k3: add i2s_sysclk, i2s_bclk_factor and i2s1_sysclk_src IDs ---
commit 1a78396155ff5bfe1746259b3e076109f3ecbd38
Author: Troy Mitchell <troy.mitchell@linux.spacemit.com>
dt-bindings: soc: spacemit: k3: add i2s_sysclk, i2s_bclk_factor and i2s1_sysclk_src IDs
This commit adds three new clock IDs for the SpacemiT K3 SoC to expose
clocks related to an I2S topology fix.
> CLK_MPMU_I2S1_SYSCLK keeps its existing ID (47) but will be repointed to
> the real per-instance i2s1 clock in a subsequent patch. No in-tree user
> references this ID so the semantic change is contained.
[Severity: Medium]
Does the commit message reference the correct clock ID here?
Looking at include/dt-bindings/clock/spacemit,k3-clocks.h, 47 is actually
assigned to a different clock:
#define CLK_MPMU_I2S1_SYSCLK 34
...
#define CLK_MPMU_I2S2_SYSCLK 47
Could the commit message be updated to reflect the accurate existing ID for
CLK_MPMU_I2S1_SYSCLK?
--
Sashiko AI review · https://sashiko.dev/#/patchset/20260717-k3-clk-fix-i2s-v1-0-e95001a692ee@linux.spacemit.com?part=1
^ permalink raw reply
* [PATCH v8 10/10] arm64: dts: qcom: eliza: Add support for MM clock controllers
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das
In-Reply-To: <20260717-b4-eliza_mm_cc_v6-v8-0-5cca1bef2e48@oss.qualcomm.com>
Add the device nodes for the multimedia clock controllers (cambistmclkcc,
camcc, videocc, gpucc) for Qualcomm Eliza SoC.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/eliza.dtsi | 76 +++++++++++++++++++++++++++++++++++++
1 file changed, 76 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/eliza.dtsi b/arch/arm64/boot/dts/qcom/eliza.dtsi
index 977de44b816e4295dba89ecb77c6df60f6f08d15..fed88a699fc264cc49e0bda79870a8dfb0b6c7f7 100644
--- a/arch/arm64/boot/dts/qcom/eliza.dtsi
+++ b/arch/arm64/boot/dts/qcom/eliza.dtsi
@@ -4,9 +4,13 @@
*/
#include <dt-bindings/clock/qcom,dsi-phy-28nm.h>
+#include <dt-bindings/clock/qcom,eliza-cambistmclkcc.h>
+#include <dt-bindings/clock/qcom,eliza-camcc.h>
#include <dt-bindings/clock/qcom,eliza-dispcc.h>
#include <dt-bindings/clock/qcom,eliza-gcc.h>
+#include <dt-bindings/clock/qcom,eliza-gpucc.h>
#include <dt-bindings/clock/qcom,eliza-tcsr.h>
+#include <dt-bindings/clock/qcom,eliza-videocc.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/gpio/gpio.h>
@@ -1779,6 +1783,24 @@ aggre2_noc: interconnect@1700000 {
#interconnect-cells = <2>;
};
+ cambistmclkcc: clock-controller@1760000 {
+ compatible = "qcom,eliza-cambistmclkcc";
+ reg = <0x0 0x01760000 0x0 0x6000>;
+
+ clocks = <&bi_tcxo_div2>,
+ <&sleep_clk>,
+ <&gcc GCC_CAM_BIST_MCLK_AHB_CLK>;
+
+ power-domains = <&rpmhpd RPMHPD_CX>,
+ <&rpmhpd RPMHPD_MX>;
+ required-opps = <&rpmhpd_opp_low_svs>,
+ <&rpmhpd_opp_low_svs>;
+
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
mmss_noc: interconnect@1780000 {
compatible = "qcom,eliza-mmss-noc";
reg = <0x0 0x01780000 0x0 0x7d800>;
@@ -2657,6 +2679,60 @@ mdss_dp0_out: endpoint {
};
};
+ gpucc: clock-controller@3d90000 {
+ compatible = "qcom,eliza-gpucc";
+ reg = <0x0 0x03d90000 0x0 0xa000>;
+
+ clocks = <&bi_tcxo_div2>,
+ <&gcc GCC_GPU_GPLL0_CPH_CLK_SRC>,
+ <&gcc GCC_GPU_GPLL0_DIV_CPH_CLK_SRC>;
+
+ power-domains = <&rpmhpd RPMHPD_MX>,
+ <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>,
+ <&rpmhpd_opp_low_svs>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
+ videocc: clock-controller@aaf0000 {
+ compatible = "qcom,eliza-videocc";
+ reg = <0x0 0xaaf0000 0x0 0x10000>;
+
+ clocks = <&bi_tcxo_div2>,
+ <&bi_tcxo_ao_div2>,
+ <&sleep_clk>,
+ <&gcc GCC_VIDEO_AHB_CLK>;
+
+ power-domains = <&rpmhpd RPMHPD_CX>,
+ <&rpmhpd RPMHPD_MX>;
+ required-opps = <&rpmhpd_opp_low_svs>,
+ <&rpmhpd_opp_low_svs>;
+
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
+ camcc: clock-controller@ade0000 {
+ compatible = "qcom,eliza-camcc";
+ reg = <0x0 0x0ade0000 0x0 0x20000>;
+
+ clocks = <&bi_tcxo_div2>,
+ <&sleep_clk>,
+ <&gcc GCC_CAMERA_AHB_CLK>;
+
+ power-domains = <&rpmhpd RPMHPD_CX>,
+ <&rpmhpd RPMHPD_MX>;
+ required-opps = <&rpmhpd_opp_low_svs>,
+ <&rpmhpd_opp_low_svs>;
+
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
dispcc: clock-controller@af00000 {
compatible = "qcom,eliza-dispcc";
reg = <0x0 0x0af00000 0x0 0x20000>;
--
2.34.1
^ permalink raw reply related
* [PATCH v8 09/10] clk: qcom: camcc: Add support for camera clock controller for Eliza
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das
In-Reply-To: <20260717-b4-eliza_mm_cc_v6-v8-0-5cca1bef2e48@oss.qualcomm.com>
Add support for the Camera Clock Controller (CAMCC) on the Eliza
platform.
The CAMCC block on Eliza includes both the primary camera clock
controller and the Camera BIST clock controller, which provides the
functional MCLK required for camera operations.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
drivers/clk/qcom/Kconfig | 11 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/cambistmclkcc-eliza.c | 464 ++++++
drivers/clk/qcom/camcc-eliza.c | 2803 ++++++++++++++++++++++++++++++++
4 files changed, 3279 insertions(+)
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 373f925638bb026f38b8cd770760c7a9dfac684d..ac801d18bb7e0ea49ba22e74e268ea93c0bc4063 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -19,6 +19,17 @@ menuconfig COMMON_CLK_QCOM
if COMMON_CLK_QCOM
+config CLK_ELIZA_CAMCC
+ tristate "Eliza Camera Clock Controller"
+ depends on ARM64 || COMPILE_TEST
+ select CLK_ELIZA_GCC
+ default m if ARCH_QCOM
+ help
+ Support for the camera clock controller on Qualcomm Technologies, Inc
+ Eliza devices.
+ Say Y if you want to support camera devices and functionality such as
+ capturing pictures.
+
config CLK_ELIZA_DISPCC
tristate "Eliza Display Clock Controller"
depends on ARM64 || COMPILE_TEST
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 3c30b7b47d567884b4649cb13187ab2f0d77999a..9aa039f117b1cfd7ce7b79da6bf72dd4d0beb493 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -20,6 +20,7 @@ clk-qcom-$(CONFIG_QCOM_GDSC) += gdsc.o
# Keep alphabetically sorted by config
obj-$(CONFIG_APQ_GCC_8084) += gcc-apq8084.o
obj-$(CONFIG_APQ_MMCC_8084) += mmcc-apq8084.o
+obj-$(CONFIG_CLK_ELIZA_CAMCC) += cambistmclkcc-eliza.o camcc-eliza.o
obj-$(CONFIG_CLK_ELIZA_DISPCC) += dispcc-eliza.o
obj-$(CONFIG_CLK_ELIZA_GCC) += gcc-eliza.o
obj-$(CONFIG_CLK_ELIZA_GPUCC) += gpucc-eliza.o
diff --git a/drivers/clk/qcom/cambistmclkcc-eliza.c b/drivers/clk/qcom/cambistmclkcc-eliza.c
new file mode 100644
index 0000000000000000000000000000000000000000..5cb68b81095ebf04fd636e70c2b6cbda764fbbd9
--- /dev/null
+++ b/drivers/clk/qcom/cambistmclkcc-eliza.c
@@ -0,0 +1,464 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/clock/qcom,eliza-cambistmclkcc.h>
+
+#include "clk-alpha-pll.h"
+#include "clk-branch.h"
+#include "clk-pll.h"
+#include "clk-rcg.h"
+#include "clk-regmap.h"
+#include "clk-regmap-divider.h"
+#include "clk-regmap-mux.h"
+#include "common.h"
+#include "reset.h"
+
+enum {
+ DT_BI_TCXO,
+ DT_SLEEP_CLK,
+ DT_AHB_CLK,
+};
+
+enum {
+ P_BI_TCXO,
+ P_CAM_BIST_MCLK_CC_PLL0_OUT_EVEN,
+ P_CAM_BIST_MCLK_CC_PLL0_OUT_MAIN,
+ P_SLEEP_CLK,
+};
+
+static const struct pll_vco rivian_ole_vco[] = {
+ { 777000000, 1285000000, 0 },
+};
+
+/* 960.0 MHz Configuration */
+static const struct alpha_pll_config cam_bist_mclk_cc_pll0_config = {
+ .l = 0x32,
+ .cal_l = 0x32,
+ .alpha = 0x0,
+ .config_ctl_val = 0x10000030,
+ .config_ctl_hi_val = 0x80890263,
+ .config_ctl_hi1_val = 0x00000217,
+ .user_ctl_val = 0x00000001,
+ .user_ctl_hi_val = 0x00000000,
+};
+
+static struct clk_alpha_pll cam_bist_mclk_cc_pll0 = {
+ .offset = 0x0,
+ .config = &cam_bist_mclk_cc_pll0_config,
+ .vco_table = rivian_ole_vco,
+ .num_vco = ARRAY_SIZE(rivian_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_RIVIAN_EVO],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_pll0",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_rivian_evo_ops,
+ },
+ },
+};
+
+static const struct parent_map cam_bist_mclk_cc_parent_map_0[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_BIST_MCLK_CC_PLL0_OUT_EVEN, 3 },
+ { P_CAM_BIST_MCLK_CC_PLL0_OUT_MAIN, 5 },
+};
+
+static const struct clk_parent_data cam_bist_mclk_cc_parent_data_0[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &cam_bist_mclk_cc_pll0.clkr.hw },
+ { .hw = &cam_bist_mclk_cc_pll0.clkr.hw },
+};
+
+static const struct parent_map cam_bist_mclk_cc_parent_map_1[] = {
+ { P_SLEEP_CLK, 0 },
+};
+
+static const struct clk_parent_data cam_bist_mclk_cc_parent_data_1[] = {
+ { .index = DT_SLEEP_CLK },
+};
+
+static const struct freq_tbl ftbl_cam_bist_mclk_cc_mclk0_clk_src[] = {
+ F(19200000, P_BI_TCXO, 1, 0, 0),
+ F(24000000, P_CAM_BIST_MCLK_CC_PLL0_OUT_EVEN, 10, 1, 4),
+ F(68571429, P_CAM_BIST_MCLK_CC_PLL0_OUT_MAIN, 14, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_bist_mclk_cc_mclk0_clk_src = {
+ .cmd_rcgr = 0x4000,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_bist_mclk_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_bist_mclk_cc_mclk0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk0_clk_src",
+ .parent_data = cam_bist_mclk_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_bist_mclk_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_bist_mclk_cc_mclk1_clk_src = {
+ .cmd_rcgr = 0x401c,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_bist_mclk_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_bist_mclk_cc_mclk0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk1_clk_src",
+ .parent_data = cam_bist_mclk_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_bist_mclk_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_bist_mclk_cc_mclk2_clk_src = {
+ .cmd_rcgr = 0x4038,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_bist_mclk_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_bist_mclk_cc_mclk0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk2_clk_src",
+ .parent_data = cam_bist_mclk_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_bist_mclk_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_bist_mclk_cc_mclk3_clk_src = {
+ .cmd_rcgr = 0x4054,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_bist_mclk_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_bist_mclk_cc_mclk0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk3_clk_src",
+ .parent_data = cam_bist_mclk_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_bist_mclk_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_bist_mclk_cc_mclk4_clk_src = {
+ .cmd_rcgr = 0x4070,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_bist_mclk_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_bist_mclk_cc_mclk0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk4_clk_src",
+ .parent_data = cam_bist_mclk_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_bist_mclk_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_bist_mclk_cc_mclk5_clk_src = {
+ .cmd_rcgr = 0x408c,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_bist_mclk_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_bist_mclk_cc_mclk0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk5_clk_src",
+ .parent_data = cam_bist_mclk_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_bist_mclk_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_bist_mclk_cc_mclk6_clk_src = {
+ .cmd_rcgr = 0x40a8,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_bist_mclk_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_bist_mclk_cc_mclk0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk6_clk_src",
+ .parent_data = cam_bist_mclk_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_bist_mclk_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_bist_mclk_cc_mclk7_clk_src = {
+ .cmd_rcgr = 0x40c4,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_bist_mclk_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_bist_mclk_cc_mclk0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk7_clk_src",
+ .parent_data = cam_bist_mclk_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_bist_mclk_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_bist_mclk_cc_sleep_clk_src[] = {
+ F(32000, P_SLEEP_CLK, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_bist_mclk_cc_sleep_clk_src = {
+ .cmd_rcgr = 0x40e0,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_bist_mclk_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_bist_mclk_cc_sleep_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_sleep_clk_src",
+ .parent_data = cam_bist_mclk_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_bist_mclk_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_branch cam_bist_mclk_cc_mclk0_clk = {
+ .halt_reg = 0x4018,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x4018,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk0_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_bist_mclk_cc_mclk0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_bist_mclk_cc_mclk1_clk = {
+ .halt_reg = 0x4034,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x4034,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk1_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_bist_mclk_cc_mclk1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_bist_mclk_cc_mclk2_clk = {
+ .halt_reg = 0x4050,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x4050,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk2_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_bist_mclk_cc_mclk2_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_bist_mclk_cc_mclk3_clk = {
+ .halt_reg = 0x406c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x406c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk3_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_bist_mclk_cc_mclk3_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_bist_mclk_cc_mclk4_clk = {
+ .halt_reg = 0x4088,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x4088,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk4_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_bist_mclk_cc_mclk4_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_bist_mclk_cc_mclk5_clk = {
+ .halt_reg = 0x40a4,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x40a4,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk5_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_bist_mclk_cc_mclk5_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_bist_mclk_cc_mclk6_clk = {
+ .halt_reg = 0x40c0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x40c0,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk6_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_bist_mclk_cc_mclk6_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_bist_mclk_cc_mclk7_clk = {
+ .halt_reg = 0x40dc,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x40dc,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_bist_mclk_cc_mclk7_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_bist_mclk_cc_mclk7_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_regmap *cam_bist_mclk_cc_eliza_clocks[] = {
+ [CAM_BIST_MCLK_CC_MCLK0_CLK] = &cam_bist_mclk_cc_mclk0_clk.clkr,
+ [CAM_BIST_MCLK_CC_MCLK0_CLK_SRC] = &cam_bist_mclk_cc_mclk0_clk_src.clkr,
+ [CAM_BIST_MCLK_CC_MCLK1_CLK] = &cam_bist_mclk_cc_mclk1_clk.clkr,
+ [CAM_BIST_MCLK_CC_MCLK1_CLK_SRC] = &cam_bist_mclk_cc_mclk1_clk_src.clkr,
+ [CAM_BIST_MCLK_CC_MCLK2_CLK] = &cam_bist_mclk_cc_mclk2_clk.clkr,
+ [CAM_BIST_MCLK_CC_MCLK2_CLK_SRC] = &cam_bist_mclk_cc_mclk2_clk_src.clkr,
+ [CAM_BIST_MCLK_CC_MCLK3_CLK] = &cam_bist_mclk_cc_mclk3_clk.clkr,
+ [CAM_BIST_MCLK_CC_MCLK3_CLK_SRC] = &cam_bist_mclk_cc_mclk3_clk_src.clkr,
+ [CAM_BIST_MCLK_CC_MCLK4_CLK] = &cam_bist_mclk_cc_mclk4_clk.clkr,
+ [CAM_BIST_MCLK_CC_MCLK4_CLK_SRC] = &cam_bist_mclk_cc_mclk4_clk_src.clkr,
+ [CAM_BIST_MCLK_CC_MCLK5_CLK] = &cam_bist_mclk_cc_mclk5_clk.clkr,
+ [CAM_BIST_MCLK_CC_MCLK5_CLK_SRC] = &cam_bist_mclk_cc_mclk5_clk_src.clkr,
+ [CAM_BIST_MCLK_CC_MCLK6_CLK] = &cam_bist_mclk_cc_mclk6_clk.clkr,
+ [CAM_BIST_MCLK_CC_MCLK6_CLK_SRC] = &cam_bist_mclk_cc_mclk6_clk_src.clkr,
+ [CAM_BIST_MCLK_CC_MCLK7_CLK] = &cam_bist_mclk_cc_mclk7_clk.clkr,
+ [CAM_BIST_MCLK_CC_MCLK7_CLK_SRC] = &cam_bist_mclk_cc_mclk7_clk_src.clkr,
+ [CAM_BIST_MCLK_CC_PLL0] = &cam_bist_mclk_cc_pll0.clkr,
+ [CAM_BIST_MCLK_CC_SLEEP_CLK_SRC] = &cam_bist_mclk_cc_sleep_clk_src.clkr,
+};
+
+static struct clk_alpha_pll *cam_bist_mclk_cc_eliza_plls[] = {
+ &cam_bist_mclk_cc_pll0,
+};
+
+static const u32 cam_bist_mclk_cc_eliza_critical_cbcrs[] = {
+ 0x40f8, /* CAM_BIST_MCLK_CC_SLEEP_CLK */
+};
+
+static const struct regmap_config cam_bist_mclk_cc_eliza_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = 0x5010,
+ .fast_io = true,
+};
+
+static const struct qcom_cc_driver_data cam_bist_mclk_cc_eliza_driver_data = {
+ .alpha_plls = cam_bist_mclk_cc_eliza_plls,
+ .num_alpha_plls = ARRAY_SIZE(cam_bist_mclk_cc_eliza_plls),
+ .clk_cbcrs = cam_bist_mclk_cc_eliza_critical_cbcrs,
+ .num_clk_cbcrs = ARRAY_SIZE(cam_bist_mclk_cc_eliza_critical_cbcrs),
+};
+
+static const struct qcom_cc_desc cam_bist_mclk_cc_eliza_desc = {
+ .config = &cam_bist_mclk_cc_eliza_regmap_config,
+ .clks = cam_bist_mclk_cc_eliza_clocks,
+ .num_clks = ARRAY_SIZE(cam_bist_mclk_cc_eliza_clocks),
+ .use_rpm = true,
+ .driver_data = &cam_bist_mclk_cc_eliza_driver_data,
+};
+
+static const struct of_device_id cam_bist_mclk_cc_eliza_match_table[] = {
+ { .compatible = "qcom,eliza-cambistmclkcc" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, cam_bist_mclk_cc_eliza_match_table);
+
+static int cam_bist_mclk_cc_eliza_probe(struct platform_device *pdev)
+{
+ return qcom_cc_probe(pdev, &cam_bist_mclk_cc_eliza_desc);
+}
+
+static struct platform_driver cam_bist_mclk_cc_eliza_driver = {
+ .probe = cam_bist_mclk_cc_eliza_probe,
+ .driver = {
+ .name = "cambistmclkcc-eliza",
+ .of_match_table = cam_bist_mclk_cc_eliza_match_table,
+ },
+};
+
+module_platform_driver(cam_bist_mclk_cc_eliza_driver);
+
+MODULE_DESCRIPTION("QTI CAMBISTMCLKCC Eliza Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/clk/qcom/camcc-eliza.c b/drivers/clk/qcom/camcc-eliza.c
new file mode 100644
index 0000000000000000000000000000000000000000..7348f4dde65aeacc27182a926a8c0e5b88eacd74
--- /dev/null
+++ b/drivers/clk/qcom/camcc-eliza.c
@@ -0,0 +1,2803 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/clock/qcom,eliza-camcc.h>
+
+#include "clk-alpha-pll.h"
+#include "clk-branch.h"
+#include "clk-pll.h"
+#include "clk-rcg.h"
+#include "clk-regmap.h"
+#include "clk-regmap-divider.h"
+#include "clk-regmap-mux.h"
+#include "common.h"
+#include "gdsc.h"
+#include "reset.h"
+
+enum {
+ DT_BI_TCXO,
+ DT_SLEEP_CLK,
+ DT_AHB_CLK,
+};
+
+enum {
+ P_BI_TCXO,
+ P_CAM_CC_PLL0_OUT_EVEN,
+ P_CAM_CC_PLL0_OUT_MAIN,
+ P_CAM_CC_PLL0_OUT_ODD,
+ P_CAM_CC_PLL1_OUT_EVEN,
+ P_CAM_CC_PLL2_OUT_EVEN,
+ P_CAM_CC_PLL3_OUT_EVEN,
+ P_CAM_CC_PLL4_OUT_EVEN,
+ P_CAM_CC_PLL5_OUT_EVEN,
+ P_CAM_CC_PLL6_OUT_EVEN,
+ P_CAM_CC_PLL6_OUT_ODD,
+ P_SLEEP_CLK,
+};
+
+static const struct pll_vco lucid_ole_vco[] = {
+ { 249600000, 2300000000, 0 },
+};
+
+/* 1200.0 MHz Configuration */
+static const struct alpha_pll_config cam_cc_pll0_config = {
+ .l = 0x3e,
+ .cal_l = 0x44,
+ .alpha = 0x8000,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00182261,
+ .config_ctl_hi1_val = 0x82aa299c,
+ .test_ctl_val = 0x00000000,
+ .test_ctl_hi_val = 0x00000003,
+ .test_ctl_hi1_val = 0x00009000,
+ .test_ctl_hi2_val = 0x00000034,
+ .user_ctl_val = 0x00008400,
+ .user_ctl_hi_val = 0x00000005,
+};
+
+static struct clk_alpha_pll cam_cc_pll0 = {
+ .offset = 0x0,
+ .config = &cam_cc_pll0_config,
+ .vco_table = lucid_ole_vco,
+ .num_vco = ARRAY_SIZE(lucid_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll0",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_lucid_evo_ops,
+ },
+ },
+};
+
+static const struct clk_div_table post_div_table_cam_cc_pll0_out_even[] = {
+ { 0x1, 2 },
+ { }
+};
+
+static struct clk_alpha_pll_postdiv cam_cc_pll0_out_even = {
+ .offset = 0x0,
+ .post_div_shift = 10,
+ .post_div_table = post_div_table_cam_cc_pll0_out_even,
+ .num_post_div = ARRAY_SIZE(post_div_table_cam_cc_pll0_out_even),
+ .width = 4,
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll0_out_even",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_pll0.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_alpha_pll_postdiv_lucid_ole_ops,
+ },
+};
+
+static const struct clk_div_table post_div_table_cam_cc_pll0_out_odd[] = {
+ { 0x2, 3 },
+ { }
+};
+
+static struct clk_alpha_pll_postdiv cam_cc_pll0_out_odd = {
+ .offset = 0x0,
+ .post_div_shift = 14,
+ .post_div_table = post_div_table_cam_cc_pll0_out_odd,
+ .num_post_div = ARRAY_SIZE(post_div_table_cam_cc_pll0_out_odd),
+ .width = 4,
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll0_out_odd",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_pll0.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_alpha_pll_postdiv_lucid_ole_ops,
+ },
+};
+
+/* 900.0 MHz Configuration */
+static const struct alpha_pll_config cam_cc_pll1_config = {
+ .l = 0x2e,
+ .cal_l = 0x44,
+ .alpha = 0xe000,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00182261,
+ .config_ctl_hi1_val = 0x82aa299c,
+ .test_ctl_val = 0x00000000,
+ .test_ctl_hi_val = 0x00000003,
+ .test_ctl_hi1_val = 0x00009000,
+ .test_ctl_hi2_val = 0x00000034,
+ .user_ctl_val = 0x00000400,
+ .user_ctl_hi_val = 0x00000005,
+};
+
+static struct clk_alpha_pll cam_cc_pll1 = {
+ .offset = 0x1000,
+ .config = &cam_cc_pll1_config,
+ .vco_table = lucid_ole_vco,
+ .num_vco = ARRAY_SIZE(lucid_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll1",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_lucid_evo_ops,
+ },
+ },
+};
+
+static const struct clk_div_table post_div_table_cam_cc_pll1_out_even[] = {
+ { 0x1, 2 },
+ { }
+};
+
+static struct clk_alpha_pll_postdiv cam_cc_pll1_out_even = {
+ .offset = 0x1000,
+ .post_div_shift = 10,
+ .post_div_table = post_div_table_cam_cc_pll1_out_even,
+ .num_post_div = ARRAY_SIZE(post_div_table_cam_cc_pll1_out_even),
+ .width = 4,
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll1_out_even",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_pll1.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_alpha_pll_postdiv_lucid_ole_ops,
+ },
+};
+
+/* 872.0 MHz Configuration */
+static const struct alpha_pll_config cam_cc_pll2_config = {
+ .l = 0x2d,
+ .cal_l = 0x44,
+ .alpha = 0x6aaa,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00182261,
+ .config_ctl_hi1_val = 0x82aa299c,
+ .test_ctl_val = 0x00000000,
+ .test_ctl_hi_val = 0x00000003,
+ .test_ctl_hi1_val = 0x00009000,
+ .test_ctl_hi2_val = 0x00000034,
+ .user_ctl_val = 0x00000400,
+ .user_ctl_hi_val = 0x00000005,
+};
+
+static struct clk_alpha_pll cam_cc_pll2 = {
+ .offset = 0x2000,
+ .config = &cam_cc_pll2_config,
+ .vco_table = lucid_ole_vco,
+ .num_vco = ARRAY_SIZE(lucid_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll2",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_lucid_evo_ops,
+ },
+ },
+};
+
+static const struct clk_div_table post_div_table_cam_cc_pll2_out_even[] = {
+ { 0x1, 2 },
+ { }
+};
+
+static struct clk_alpha_pll_postdiv cam_cc_pll2_out_even = {
+ .offset = 0x2000,
+ .post_div_shift = 10,
+ .post_div_table = post_div_table_cam_cc_pll2_out_even,
+ .num_post_div = ARRAY_SIZE(post_div_table_cam_cc_pll2_out_even),
+ .width = 4,
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll2_out_even",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_pll2.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_alpha_pll_postdiv_lucid_ole_ops,
+ },
+};
+
+/* 890.0 MHz Configuration */
+static const struct alpha_pll_config cam_cc_pll3_config = {
+ .l = 0x2e,
+ .cal_l = 0x44,
+ .alpha = 0x5aaa,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00182261,
+ .config_ctl_hi1_val = 0x82aa299c,
+ .test_ctl_val = 0x00000000,
+ .test_ctl_hi_val = 0x00000003,
+ .test_ctl_hi1_val = 0x00009000,
+ .test_ctl_hi2_val = 0x00000034,
+ .user_ctl_val = 0x00000400,
+ .user_ctl_hi_val = 0x00000005,
+};
+
+static struct clk_alpha_pll cam_cc_pll3 = {
+ .offset = 0x3000,
+ .config = &cam_cc_pll3_config,
+ .vco_table = lucid_ole_vco,
+ .num_vco = ARRAY_SIZE(lucid_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll3",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_lucid_evo_ops,
+ },
+ },
+};
+
+static const struct clk_div_table post_div_table_cam_cc_pll3_out_even[] = {
+ { 0x1, 2 },
+ { }
+};
+
+static struct clk_alpha_pll_postdiv cam_cc_pll3_out_even = {
+ .offset = 0x3000,
+ .post_div_shift = 10,
+ .post_div_table = post_div_table_cam_cc_pll3_out_even,
+ .num_post_div = ARRAY_SIZE(post_div_table_cam_cc_pll3_out_even),
+ .width = 4,
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll3_out_even",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_pll3.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_alpha_pll_postdiv_lucid_ole_ops,
+ },
+};
+
+/* 890.0 MHz Configuration */
+static const struct alpha_pll_config cam_cc_pll4_config = {
+ .l = 0x2e,
+ .cal_l = 0x44,
+ .alpha = 0x5aaa,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00182261,
+ .config_ctl_hi1_val = 0x82aa299c,
+ .test_ctl_val = 0x00000000,
+ .test_ctl_hi_val = 0x00000003,
+ .test_ctl_hi1_val = 0x00009000,
+ .test_ctl_hi2_val = 0x00000034,
+ .user_ctl_val = 0x00000400,
+ .user_ctl_hi_val = 0x00000005,
+};
+
+static struct clk_alpha_pll cam_cc_pll4 = {
+ .offset = 0x4000,
+ .config = &cam_cc_pll4_config,
+ .vco_table = lucid_ole_vco,
+ .num_vco = ARRAY_SIZE(lucid_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll4",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_lucid_evo_ops,
+ },
+ },
+};
+
+static const struct clk_div_table post_div_table_cam_cc_pll4_out_even[] = {
+ { 0x1, 2 },
+ { }
+};
+
+static struct clk_alpha_pll_postdiv cam_cc_pll4_out_even = {
+ .offset = 0x4000,
+ .post_div_shift = 10,
+ .post_div_table = post_div_table_cam_cc_pll4_out_even,
+ .num_post_div = ARRAY_SIZE(post_div_table_cam_cc_pll4_out_even),
+ .width = 4,
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll4_out_even",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_pll4.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_alpha_pll_postdiv_lucid_ole_ops,
+ },
+};
+
+/* 890.0 MHz Configuration */
+static const struct alpha_pll_config cam_cc_pll5_config = {
+ .l = 0x2e,
+ .cal_l = 0x44,
+ .alpha = 0x5aaa,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00182261,
+ .config_ctl_hi1_val = 0x82aa299c,
+ .test_ctl_val = 0x00000000,
+ .test_ctl_hi_val = 0x00000003,
+ .test_ctl_hi1_val = 0x00009000,
+ .test_ctl_hi2_val = 0x00000034,
+ .user_ctl_val = 0x00000400,
+ .user_ctl_hi_val = 0x00000005,
+};
+
+static struct clk_alpha_pll cam_cc_pll5 = {
+ .offset = 0x5000,
+ .config = &cam_cc_pll5_config,
+ .vco_table = lucid_ole_vco,
+ .num_vco = ARRAY_SIZE(lucid_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll5",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_lucid_evo_ops,
+ },
+ },
+};
+
+static const struct clk_div_table post_div_table_cam_cc_pll5_out_even[] = {
+ { 0x1, 2 },
+ { }
+};
+
+static struct clk_alpha_pll_postdiv cam_cc_pll5_out_even = {
+ .offset = 0x5000,
+ .post_div_shift = 10,
+ .post_div_table = post_div_table_cam_cc_pll5_out_even,
+ .num_post_div = ARRAY_SIZE(post_div_table_cam_cc_pll5_out_even),
+ .width = 4,
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll5_out_even",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_pll5.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_alpha_pll_postdiv_lucid_ole_ops,
+ },
+};
+
+/* 960.0 MHz Configuration */
+static const struct alpha_pll_config cam_cc_pll6_config = {
+ .l = 0x32,
+ .cal_l = 0x44,
+ .alpha = 0x0,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00182261,
+ .config_ctl_hi1_val = 0x82aa299c,
+ .test_ctl_val = 0x00000000,
+ .test_ctl_hi_val = 0x00000003,
+ .test_ctl_hi1_val = 0x00009000,
+ .test_ctl_hi2_val = 0x00000034,
+ .user_ctl_val = 0x00008400,
+ .user_ctl_hi_val = 0x00000005,
+};
+
+static struct clk_alpha_pll cam_cc_pll6 = {
+ .offset = 0x6000,
+ .config = &cam_cc_pll6_config,
+ .vco_table = lucid_ole_vco,
+ .num_vco = ARRAY_SIZE(lucid_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll6",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_lucid_evo_ops,
+ },
+ },
+};
+
+static const struct clk_div_table post_div_table_cam_cc_pll6_out_even[] = {
+ { 0x1, 2 },
+ { }
+};
+
+static struct clk_alpha_pll_postdiv cam_cc_pll6_out_even = {
+ .offset = 0x6000,
+ .post_div_shift = 10,
+ .post_div_table = post_div_table_cam_cc_pll6_out_even,
+ .num_post_div = ARRAY_SIZE(post_div_table_cam_cc_pll6_out_even),
+ .width = 4,
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll6_out_even",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_pll6.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_alpha_pll_postdiv_lucid_ole_ops,
+ },
+};
+
+static const struct clk_div_table post_div_table_cam_cc_pll6_out_odd[] = {
+ { 0x2, 3 },
+ { }
+};
+
+static struct clk_alpha_pll_postdiv cam_cc_pll6_out_odd = {
+ .offset = 0x6000,
+ .post_div_shift = 14,
+ .post_div_table = post_div_table_cam_cc_pll6_out_odd,
+ .num_post_div = ARRAY_SIZE(post_div_table_cam_cc_pll6_out_odd),
+ .width = 4,
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_pll6_out_odd",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_pll6.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_alpha_pll_postdiv_lucid_ole_ops,
+ },
+};
+
+static const struct parent_map cam_cc_parent_map_0[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL0_OUT_MAIN, 1 },
+ { P_CAM_CC_PLL0_OUT_EVEN, 2 },
+ { P_CAM_CC_PLL0_OUT_ODD, 3 },
+ { P_CAM_CC_PLL6_OUT_ODD, 4 },
+ { P_CAM_CC_PLL6_OUT_EVEN, 5 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_0[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &cam_cc_pll0.clkr.hw },
+ { .hw = &cam_cc_pll0_out_even.clkr.hw },
+ { .hw = &cam_cc_pll0_out_odd.clkr.hw },
+ { .hw = &cam_cc_pll6_out_odd.clkr.hw },
+ { .hw = &cam_cc_pll6_out_even.clkr.hw },
+};
+
+static const struct parent_map cam_cc_parent_map_1[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL0_OUT_MAIN, 1 },
+ { P_CAM_CC_PLL0_OUT_EVEN, 2 },
+ { P_CAM_CC_PLL0_OUT_ODD, 3 },
+ { P_CAM_CC_PLL6_OUT_ODD, 4 },
+ { P_CAM_CC_PLL6_OUT_EVEN, 5 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_1[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &cam_cc_pll0.clkr.hw },
+ { .hw = &cam_cc_pll0_out_even.clkr.hw },
+ { .hw = &cam_cc_pll0_out_odd.clkr.hw },
+ { .hw = &cam_cc_pll6_out_odd.clkr.hw },
+ { .hw = &cam_cc_pll6_out_even.clkr.hw },
+};
+
+static const struct parent_map cam_cc_parent_map_2[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL1_OUT_EVEN, 4 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_2[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &cam_cc_pll1_out_even.clkr.hw },
+};
+
+static const struct parent_map cam_cc_parent_map_3[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL2_OUT_EVEN, 5 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_3[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &cam_cc_pll2_out_even.clkr.hw },
+};
+
+static const struct parent_map cam_cc_parent_map_4[] = {
+ { P_SLEEP_CLK, 0 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_4[] = {
+ { .index = DT_SLEEP_CLK },
+};
+
+static const struct parent_map cam_cc_parent_map_5[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL3_OUT_EVEN, 6 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_5[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &cam_cc_pll3_out_even.clkr.hw },
+};
+
+static const struct parent_map cam_cc_parent_map_6[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL4_OUT_EVEN, 6 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_6[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &cam_cc_pll4_out_even.clkr.hw },
+};
+
+static const struct parent_map cam_cc_parent_map_7[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL5_OUT_EVEN, 6 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_7[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &cam_cc_pll5_out_even.clkr.hw },
+};
+
+static const struct parent_map cam_cc_parent_map_8[] = {
+ { P_BI_TCXO, 0 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_8[] = {
+ { .index = DT_BI_TCXO },
+};
+
+static const struct freq_tbl ftbl_cam_cc_camnoc_rt_axi_clk_src[] = {
+ F(19200000, P_BI_TCXO, 1, 0, 0),
+ F(300000000, P_CAM_CC_PLL0_OUT_EVEN, 2, 0, 0),
+ F(400000000, P_CAM_CC_PLL0_OUT_ODD, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_camnoc_rt_axi_clk_src = {
+ .cmd_rcgr = 0x112e8,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_camnoc_rt_axi_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_rt_axi_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_cci_0_clk_src[] = {
+ F(37500000, P_CAM_CC_PLL0_OUT_EVEN, 16, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_cci_0_clk_src = {
+ .cmd_rcgr = 0x1126c,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_cci_0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cci_0_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_cci_1_clk_src = {
+ .cmd_rcgr = 0x11288,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_cci_0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cci_1_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_cci_2_clk_src = {
+ .cmd_rcgr = 0x112a4,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_cci_0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cci_2_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_cphy_rx_clk_src[] = {
+ F(400000000, P_CAM_CC_PLL0_OUT_MAIN, 3, 0, 0),
+ F(480000000, P_CAM_CC_PLL0_OUT_MAIN, 2.5, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_cphy_rx_clk_src = {
+ .cmd_rcgr = 0x11068,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_cphy_rx_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cphy_rx_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_cre_clk_src[] = {
+ F(200000000, P_CAM_CC_PLL0_OUT_ODD, 2, 0, 0),
+ F(400000000, P_CAM_CC_PLL0_OUT_ODD, 1, 0, 0),
+ F(480000000, P_CAM_CC_PLL6_OUT_EVEN, 1, 0, 0),
+ F(600000000, P_CAM_CC_PLL0_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_cre_clk_src = {
+ .cmd_rcgr = 0x111ac,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_cre_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cre_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_csi0phytimer_clk_src[] = {
+ F(400000000, P_CAM_CC_PLL0_OUT_MAIN, 3, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_csi0phytimer_clk_src = {
+ .cmd_rcgr = 0x10000,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_csi0phytimer_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi0phytimer_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_csi1phytimer_clk_src = {
+ .cmd_rcgr = 0x10024,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_csi0phytimer_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi1phytimer_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_csi2phytimer_clk_src = {
+ .cmd_rcgr = 0x10044,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_csi0phytimer_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi2phytimer_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_csi3phytimer_clk_src = {
+ .cmd_rcgr = 0x10064,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_csi0phytimer_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi3phytimer_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_csi4phytimer_clk_src = {
+ .cmd_rcgr = 0x10084,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_csi0phytimer_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi4phytimer_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_csi5phytimer_clk_src = {
+ .cmd_rcgr = 0x100a4,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_csi0phytimer_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi5phytimer_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_csid_clk_src = {
+ .cmd_rcgr = 0x112c0,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_cphy_rx_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csid_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_fast_ahb_clk_src[] = {
+ F(300000000, P_CAM_CC_PLL0_OUT_EVEN, 2, 0, 0),
+ F(400000000, P_CAM_CC_PLL0_OUT_MAIN, 3, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_fast_ahb_clk_src = {
+ .cmd_rcgr = 0x100dc,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_fast_ahb_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_fast_ahb_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_icp_0_clk_src[] = {
+ F(400000000, P_CAM_CC_PLL0_OUT_ODD, 1, 0, 0),
+ F(480000000, P_CAM_CC_PLL6_OUT_EVEN, 1, 0, 0),
+ F(600000000, P_CAM_CC_PLL0_OUT_MAIN, 2, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_icp_0_clk_src = {
+ .cmd_rcgr = 0x11214,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_icp_0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_icp_0_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_icp_1_clk_src = {
+ .cmd_rcgr = 0x1123c,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_icp_0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_icp_1_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_ife_lite_clk_src = {
+ .cmd_rcgr = 0x11150,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_cphy_rx_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ife_lite_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_ife_lite_csid_clk_src = {
+ .cmd_rcgr = 0x1117c,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_cphy_rx_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ife_lite_csid_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_ipe_nps_clk_src[] = {
+ F(450000000, P_CAM_CC_PLL1_OUT_EVEN, 1, 0, 0),
+ F(575000000, P_CAM_CC_PLL1_OUT_EVEN, 1, 0, 0),
+ F(675000000, P_CAM_CC_PLL1_OUT_EVEN, 1, 0, 0),
+ F(825000000, P_CAM_CC_PLL1_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_ipe_nps_clk_src = {
+ .cmd_rcgr = 0x10190,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_2,
+ .freq_tbl = ftbl_cam_cc_ipe_nps_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ipe_nps_clk_src",
+ .parent_data = cam_cc_parent_data_2,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_2),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_jpeg_clk_src = {
+ .cmd_rcgr = 0x111d0,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_cre_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_jpeg_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_ofe_clk_src[] = {
+ F(436000000, P_CAM_CC_PLL2_OUT_EVEN, 1, 0, 0),
+ F(570000000, P_CAM_CC_PLL2_OUT_EVEN, 1, 0, 0),
+ F(675000000, P_CAM_CC_PLL2_OUT_EVEN, 1, 0, 0),
+ F(757000000, P_CAM_CC_PLL2_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_ofe_clk_src = {
+ .cmd_rcgr = 0x1011c,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_3,
+ .freq_tbl = ftbl_cam_cc_ofe_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ofe_clk_src",
+ .parent_data = cam_cc_parent_data_3,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_3),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_qdss_debug_clk_src[] = {
+ F(60000000, P_CAM_CC_PLL6_OUT_EVEN, 8, 0, 0),
+ F(120000000, P_CAM_CC_PLL0_OUT_EVEN, 5, 0, 0),
+ F(240000000, P_CAM_CC_PLL0_OUT_MAIN, 5, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_qdss_debug_clk_src = {
+ .cmd_rcgr = 0x1132c,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_qdss_debug_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_qdss_debug_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_sleep_clk_src[] = {
+ F(32000, P_SLEEP_CLK, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_sleep_clk_src = {
+ .cmd_rcgr = 0x11380,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_4,
+ .freq_tbl = ftbl_cam_cc_sleep_clk_src,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_sleep_clk_src",
+ .parent_data = cam_cc_parent_data_4,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_4),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_slow_ahb_clk_src[] = {
+ F(80000000, P_CAM_CC_PLL0_OUT_EVEN, 7.5, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_slow_ahb_clk_src = {
+ .cmd_rcgr = 0x10100,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_slow_ahb_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_slow_ahb_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_tfe_0_clk_src[] = {
+ F(445000000, P_CAM_CC_PLL3_OUT_EVEN, 1, 0, 0),
+ F(567000000, P_CAM_CC_PLL3_OUT_EVEN, 1, 0, 0),
+ F(644000000, P_CAM_CC_PLL3_OUT_EVEN, 1, 0, 0),
+ F(785000000, P_CAM_CC_PLL3_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_tfe_0_clk_src = {
+ .cmd_rcgr = 0x11018,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_5,
+ .freq_tbl = ftbl_cam_cc_tfe_0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_0_clk_src",
+ .parent_data = cam_cc_parent_data_5,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_5),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_tfe_1_clk_src[] = {
+ F(445000000, P_CAM_CC_PLL4_OUT_EVEN, 1, 0, 0),
+ F(567000000, P_CAM_CC_PLL4_OUT_EVEN, 1, 0, 0),
+ F(644000000, P_CAM_CC_PLL4_OUT_EVEN, 1, 0, 0),
+ F(785000000, P_CAM_CC_PLL4_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_tfe_1_clk_src = {
+ .cmd_rcgr = 0x11098,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_6,
+ .freq_tbl = ftbl_cam_cc_tfe_1_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_1_clk_src",
+ .parent_data = cam_cc_parent_data_6,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_6),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_tfe_2_clk_src[] = {
+ F(445000000, P_CAM_CC_PLL5_OUT_EVEN, 1, 0, 0),
+ F(567000000, P_CAM_CC_PLL5_OUT_EVEN, 1, 0, 0),
+ F(644000000, P_CAM_CC_PLL5_OUT_EVEN, 1, 0, 0),
+ F(785000000, P_CAM_CC_PLL5_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_tfe_2_clk_src = {
+ .cmd_rcgr = 0x11100,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_7,
+ .freq_tbl = ftbl_cam_cc_tfe_2_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_2_clk_src",
+ .parent_data = cam_cc_parent_data_7,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_7),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_xo_clk_src[] = {
+ F(19200000, P_BI_TCXO, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_xo_clk_src = {
+ .cmd_rcgr = 0x11364,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_8,
+ .freq_tbl = ftbl_cam_cc_xo_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_xo_clk_src",
+ .parent_data = cam_cc_parent_data_8,
+ .num_parents = ARRAY_SIZE(cam_cc_parent_data_8),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_branch cam_cc_cam_top_ahb_clk = {
+ .halt_reg = 0x113ac,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x113ac,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cam_top_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_cam_top_fast_ahb_clk = {
+ .halt_reg = 0x1139c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1139c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cam_top_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_dcd_xo_clk = {
+ .halt_reg = 0x11320,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11320,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_dcd_xo_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_xo_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_nrt_axi_clk = {
+ .halt_reg = 0x11310,
+ .halt_check = BRANCH_HALT_VOTED,
+ .hwcg_reg = 0x11310,
+ .hwcg_bit = 1,
+ .clkr = {
+ .enable_reg = 0x11310,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_nrt_axi_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_camnoc_rt_axi_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_nrt_cre_clk = {
+ .halt_reg = 0x111c8,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x111c8,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_nrt_cre_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cre_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_nrt_ipe_nps_clk = {
+ .halt_reg = 0x101b8,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x101b8,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_nrt_ipe_nps_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ipe_nps_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_nrt_ofe_anchor_clk = {
+ .halt_reg = 0x10158,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x10158,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_nrt_ofe_anchor_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ofe_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_nrt_ofe_hdr_clk = {
+ .halt_reg = 0x1016c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1016c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_nrt_ofe_hdr_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ofe_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_nrt_ofe_main_clk = {
+ .halt_reg = 0x10144,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x10144,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_nrt_ofe_main_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ofe_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_rt_axi_clk = {
+ .halt_reg = 0x11300,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11300,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_rt_axi_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_camnoc_rt_axi_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_rt_ife_lite_clk = {
+ .halt_reg = 0x11178,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11178,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_rt_ife_lite_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ife_lite_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_rt_tfe_0_bayer_clk = {
+ .halt_reg = 0x11054,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11054,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_rt_tfe_0_bayer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_rt_tfe_0_main_clk = {
+ .halt_reg = 0x11040,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11040,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_rt_tfe_0_main_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_rt_tfe_1_bayer_clk = {
+ .halt_reg = 0x110d4,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x110d4,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_rt_tfe_1_bayer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_rt_tfe_1_main_clk = {
+ .halt_reg = 0x110c0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x110c0,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_rt_tfe_1_main_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_rt_tfe_2_bayer_clk = {
+ .halt_reg = 0x1113c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1113c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_rt_tfe_2_bayer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_2_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_rt_tfe_2_main_clk = {
+ .halt_reg = 0x11128,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11128,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_rt_tfe_2_main_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_2_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_xo_clk = {
+ .halt_reg = 0x11324,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11324,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_camnoc_xo_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_xo_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_cci_0_clk = {
+ .halt_reg = 0x11284,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11284,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cci_0_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cci_0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_cci_1_clk = {
+ .halt_reg = 0x112a0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x112a0,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cci_1_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cci_1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_cci_2_clk = {
+ .halt_reg = 0x112bc,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x112bc,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cci_2_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cci_2_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_core_ahb_clk = {
+ .halt_reg = 0x11360,
+ .halt_check = BRANCH_HALT_DELAY,
+ .clkr = {
+ .enable_reg = 0x11360,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_core_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_cre_ahb_clk = {
+ .halt_reg = 0x111cc,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x111cc,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cre_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_cre_clk = {
+ .halt_reg = 0x111c4,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x111c4,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_cre_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cre_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csi0phytimer_clk = {
+ .halt_reg = 0x10018,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x10018,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi0phytimer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_csi0phytimer_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csi1phytimer_clk = {
+ .halt_reg = 0x1003c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1003c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi1phytimer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_csi1phytimer_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csi2phytimer_clk = {
+ .halt_reg = 0x1005c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1005c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi2phytimer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_csi2phytimer_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csi3phytimer_clk = {
+ .halt_reg = 0x1007c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1007c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi3phytimer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_csi3phytimer_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csi4phytimer_clk = {
+ .halt_reg = 0x1009c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1009c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi4phytimer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_csi4phytimer_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csi5phytimer_clk = {
+ .halt_reg = 0x100bc,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x100bc,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csi5phytimer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_csi5phytimer_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csid_clk = {
+ .halt_reg = 0x112d8,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x112d8,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csid_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_csid_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csid_csiphy_rx_clk = {
+ .halt_reg = 0x10020,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x10020,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csid_csiphy_rx_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csiphy0_clk = {
+ .halt_reg = 0x1001c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1001c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csiphy0_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csiphy1_clk = {
+ .halt_reg = 0x10040,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x10040,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csiphy1_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csiphy2_clk = {
+ .halt_reg = 0x10060,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x10060,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csiphy2_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csiphy3_clk = {
+ .halt_reg = 0x10080,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x10080,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csiphy3_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csiphy4_clk = {
+ .halt_reg = 0x100a0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x100a0,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csiphy4_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csiphy5_clk = {
+ .halt_reg = 0x100c0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x100c0,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_csiphy5_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_drv_ahb_clk = {
+ .halt_reg = 0x113c4,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x113c4,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_drv_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_aon_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_drv_xo_clk = {
+ .halt_reg = 0x113c0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x113c0,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_drv_xo_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_xo_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_aon_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_icp_0_ahb_clk = {
+ .halt_reg = 0x11264,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11264,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_icp_0_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_icp_0_clk = {
+ .halt_reg = 0x1122c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1122c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_icp_0_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_icp_0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_icp_1_ahb_clk = {
+ .halt_reg = 0x11268,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11268,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_icp_1_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_icp_1_clk = {
+ .halt_reg = 0x11254,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11254,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_icp_1_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_icp_1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_lite_ahb_clk = {
+ .halt_reg = 0x111a8,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x111a8,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ife_lite_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_lite_clk = {
+ .halt_reg = 0x11168,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11168,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ife_lite_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ife_lite_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_lite_cphy_rx_clk = {
+ .halt_reg = 0x111a4,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x111a4,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ife_lite_cphy_rx_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_lite_csid_clk = {
+ .halt_reg = 0x11194,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11194,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ife_lite_csid_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ife_lite_csid_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ipe_nps_ahb_clk = {
+ .halt_reg = 0x101d4,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x101d4,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ipe_nps_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ipe_nps_clk = {
+ .halt_reg = 0x101a8,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x101a8,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ipe_nps_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ipe_nps_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ipe_nps_fast_ahb_clk = {
+ .halt_reg = 0x101d8,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x101d8,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ipe_nps_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ipe_pps_clk = {
+ .halt_reg = 0x101bc,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x101bc,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ipe_pps_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ipe_nps_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ipe_pps_fast_ahb_clk = {
+ .halt_reg = 0x101dc,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x101dc,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ipe_pps_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_jpeg_0_clk = {
+ .halt_reg = 0x111e8,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x111e8,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_jpeg_0_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_jpeg_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_jpeg_1_clk = {
+ .halt_reg = 0x111f8,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x111f8,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_jpeg_1_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_jpeg_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ofe_ahb_clk = {
+ .halt_reg = 0x10118,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x10118,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ofe_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ofe_anchor_clk = {
+ .halt_reg = 0x10148,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x10148,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ofe_anchor_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ofe_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ofe_anchor_fast_ahb_clk = {
+ .halt_reg = 0x100f8,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x100f8,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ofe_anchor_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ofe_hdr_clk = {
+ .halt_reg = 0x1015c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1015c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ofe_hdr_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ofe_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ofe_hdr_fast_ahb_clk = {
+ .halt_reg = 0x100fc,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x100fc,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ofe_hdr_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ofe_main_clk = {
+ .halt_reg = 0x10134,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x10134,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ofe_main_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_ofe_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ofe_main_fast_ahb_clk = {
+ .halt_reg = 0x100f4,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x100f4,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_ofe_main_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_qdss_debug_clk = {
+ .halt_reg = 0x11344,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11344,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_qdss_debug_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_qdss_debug_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_qdss_debug_xo_clk = {
+ .halt_reg = 0x11348,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11348,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_qdss_debug_xo_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_xo_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_0_bayer_clk = {
+ .halt_reg = 0x11044,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11044,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_0_bayer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_0_bayer_fast_ahb_clk = {
+ .halt_reg = 0x11064,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11064,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_0_bayer_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_0_main_clk = {
+ .halt_reg = 0x11030,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11030,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_0_main_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_0_main_fast_ahb_clk = {
+ .halt_reg = 0x11060,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11060,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_0_main_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_1_bayer_clk = {
+ .halt_reg = 0x110c4,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x110c4,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_1_bayer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_1_bayer_fast_ahb_clk = {
+ .halt_reg = 0x110e4,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x110e4,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_1_bayer_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_1_main_clk = {
+ .halt_reg = 0x110b0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x110b0,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_1_main_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_1_main_fast_ahb_clk = {
+ .halt_reg = 0x110e0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x110e0,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_1_main_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_2_bayer_clk = {
+ .halt_reg = 0x1112c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1112c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_2_bayer_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_2_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_2_bayer_fast_ahb_clk = {
+ .halt_reg = 0x1114c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x1114c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_2_bayer_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_2_main_clk = {
+ .halt_reg = 0x11118,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11118,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_2_main_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_tfe_2_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_tfe_2_main_fast_ahb_clk = {
+ .halt_reg = 0x11148,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x11148,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "cam_cc_tfe_2_main_fast_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct gdsc cam_cc_titan_top_gdsc = {
+ .gdscr = 0x1134c,
+ .en_rest_wait_val = 0x2,
+ .en_few_wait_val = 0x2,
+ .clk_dis_wait_val = 0xf,
+ .pd = {
+ .name = "cam_cc_titan_top_gdsc",
+ },
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = POLL_CFG_GDSCR | RETAIN_FF_ENABLE,
+};
+
+static struct gdsc cam_cc_ipe_0_gdsc = {
+ .gdscr = 0x1017c,
+ .en_rest_wait_val = 0x2,
+ .en_few_wait_val = 0x2,
+ .clk_dis_wait_val = 0xf,
+ .pd = {
+ .name = "cam_cc_ipe_0_gdsc",
+ },
+ .parent = &cam_cc_titan_top_gdsc.pd,
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = HW_CTRL_TRIGGER | POLL_CFG_GDSCR | RETAIN_FF_ENABLE,
+};
+
+static struct gdsc cam_cc_ofe_gdsc = {
+ .gdscr = 0x100c8,
+ .en_rest_wait_val = 0x2,
+ .en_few_wait_val = 0x2,
+ .clk_dis_wait_val = 0xf,
+ .pd = {
+ .name = "cam_cc_ofe_gdsc",
+ },
+ .parent = &cam_cc_titan_top_gdsc.pd,
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = HW_CTRL_TRIGGER | POLL_CFG_GDSCR | RETAIN_FF_ENABLE,
+};
+
+static struct gdsc cam_cc_tfe_0_gdsc = {
+ .gdscr = 0x11004,
+ .en_rest_wait_val = 0x2,
+ .en_few_wait_val = 0x2,
+ .clk_dis_wait_val = 0xf,
+ .pd = {
+ .name = "cam_cc_tfe_0_gdsc",
+ },
+ .parent = &cam_cc_titan_top_gdsc.pd,
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = POLL_CFG_GDSCR | RETAIN_FF_ENABLE,
+};
+
+static struct gdsc cam_cc_tfe_1_gdsc = {
+ .gdscr = 0x11084,
+ .en_rest_wait_val = 0x2,
+ .en_few_wait_val = 0x2,
+ .clk_dis_wait_val = 0xf,
+ .pd = {
+ .name = "cam_cc_tfe_1_gdsc",
+ },
+ .parent = &cam_cc_titan_top_gdsc.pd,
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = POLL_CFG_GDSCR | RETAIN_FF_ENABLE,
+};
+
+static struct gdsc cam_cc_tfe_2_gdsc = {
+ .gdscr = 0x110ec,
+ .en_rest_wait_val = 0x2,
+ .en_few_wait_val = 0x2,
+ .clk_dis_wait_val = 0xf,
+ .pd = {
+ .name = "cam_cc_tfe_2_gdsc",
+ },
+ .parent = &cam_cc_titan_top_gdsc.pd,
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = POLL_CFG_GDSCR | RETAIN_FF_ENABLE,
+};
+
+static struct clk_regmap *cam_cc_eliza_clocks[] = {
+ [CAM_CC_CAM_TOP_AHB_CLK] = &cam_cc_cam_top_ahb_clk.clkr,
+ [CAM_CC_CAM_TOP_FAST_AHB_CLK] = &cam_cc_cam_top_fast_ahb_clk.clkr,
+ [CAM_CC_CAMNOC_DCD_XO_CLK] = &cam_cc_camnoc_dcd_xo_clk.clkr,
+ [CAM_CC_CAMNOC_NRT_AXI_CLK] = &cam_cc_camnoc_nrt_axi_clk.clkr,
+ [CAM_CC_CAMNOC_NRT_CRE_CLK] = &cam_cc_camnoc_nrt_cre_clk.clkr,
+ [CAM_CC_CAMNOC_NRT_IPE_NPS_CLK] = &cam_cc_camnoc_nrt_ipe_nps_clk.clkr,
+ [CAM_CC_CAMNOC_NRT_OFE_ANCHOR_CLK] = &cam_cc_camnoc_nrt_ofe_anchor_clk.clkr,
+ [CAM_CC_CAMNOC_NRT_OFE_HDR_CLK] = &cam_cc_camnoc_nrt_ofe_hdr_clk.clkr,
+ [CAM_CC_CAMNOC_NRT_OFE_MAIN_CLK] = &cam_cc_camnoc_nrt_ofe_main_clk.clkr,
+ [CAM_CC_CAMNOC_RT_AXI_CLK] = &cam_cc_camnoc_rt_axi_clk.clkr,
+ [CAM_CC_CAMNOC_RT_AXI_CLK_SRC] = &cam_cc_camnoc_rt_axi_clk_src.clkr,
+ [CAM_CC_CAMNOC_RT_IFE_LITE_CLK] = &cam_cc_camnoc_rt_ife_lite_clk.clkr,
+ [CAM_CC_CAMNOC_RT_TFE_0_BAYER_CLK] = &cam_cc_camnoc_rt_tfe_0_bayer_clk.clkr,
+ [CAM_CC_CAMNOC_RT_TFE_0_MAIN_CLK] = &cam_cc_camnoc_rt_tfe_0_main_clk.clkr,
+ [CAM_CC_CAMNOC_RT_TFE_1_BAYER_CLK] = &cam_cc_camnoc_rt_tfe_1_bayer_clk.clkr,
+ [CAM_CC_CAMNOC_RT_TFE_1_MAIN_CLK] = &cam_cc_camnoc_rt_tfe_1_main_clk.clkr,
+ [CAM_CC_CAMNOC_RT_TFE_2_BAYER_CLK] = &cam_cc_camnoc_rt_tfe_2_bayer_clk.clkr,
+ [CAM_CC_CAMNOC_RT_TFE_2_MAIN_CLK] = &cam_cc_camnoc_rt_tfe_2_main_clk.clkr,
+ [CAM_CC_CAMNOC_XO_CLK] = &cam_cc_camnoc_xo_clk.clkr,
+ [CAM_CC_CCI_0_CLK] = &cam_cc_cci_0_clk.clkr,
+ [CAM_CC_CCI_0_CLK_SRC] = &cam_cc_cci_0_clk_src.clkr,
+ [CAM_CC_CCI_1_CLK] = &cam_cc_cci_1_clk.clkr,
+ [CAM_CC_CCI_1_CLK_SRC] = &cam_cc_cci_1_clk_src.clkr,
+ [CAM_CC_CCI_2_CLK] = &cam_cc_cci_2_clk.clkr,
+ [CAM_CC_CCI_2_CLK_SRC] = &cam_cc_cci_2_clk_src.clkr,
+ [CAM_CC_CORE_AHB_CLK] = &cam_cc_core_ahb_clk.clkr,
+ [CAM_CC_CPHY_RX_CLK_SRC] = &cam_cc_cphy_rx_clk_src.clkr,
+ [CAM_CC_CRE_AHB_CLK] = &cam_cc_cre_ahb_clk.clkr,
+ [CAM_CC_CRE_CLK] = &cam_cc_cre_clk.clkr,
+ [CAM_CC_CRE_CLK_SRC] = &cam_cc_cre_clk_src.clkr,
+ [CAM_CC_CSI0PHYTIMER_CLK] = &cam_cc_csi0phytimer_clk.clkr,
+ [CAM_CC_CSI0PHYTIMER_CLK_SRC] = &cam_cc_csi0phytimer_clk_src.clkr,
+ [CAM_CC_CSI1PHYTIMER_CLK] = &cam_cc_csi1phytimer_clk.clkr,
+ [CAM_CC_CSI1PHYTIMER_CLK_SRC] = &cam_cc_csi1phytimer_clk_src.clkr,
+ [CAM_CC_CSI2PHYTIMER_CLK] = &cam_cc_csi2phytimer_clk.clkr,
+ [CAM_CC_CSI2PHYTIMER_CLK_SRC] = &cam_cc_csi2phytimer_clk_src.clkr,
+ [CAM_CC_CSI3PHYTIMER_CLK] = &cam_cc_csi3phytimer_clk.clkr,
+ [CAM_CC_CSI3PHYTIMER_CLK_SRC] = &cam_cc_csi3phytimer_clk_src.clkr,
+ [CAM_CC_CSI4PHYTIMER_CLK] = &cam_cc_csi4phytimer_clk.clkr,
+ [CAM_CC_CSI4PHYTIMER_CLK_SRC] = &cam_cc_csi4phytimer_clk_src.clkr,
+ [CAM_CC_CSI5PHYTIMER_CLK] = &cam_cc_csi5phytimer_clk.clkr,
+ [CAM_CC_CSI5PHYTIMER_CLK_SRC] = &cam_cc_csi5phytimer_clk_src.clkr,
+ [CAM_CC_CSID_CLK] = &cam_cc_csid_clk.clkr,
+ [CAM_CC_CSID_CLK_SRC] = &cam_cc_csid_clk_src.clkr,
+ [CAM_CC_CSID_CSIPHY_RX_CLK] = &cam_cc_csid_csiphy_rx_clk.clkr,
+ [CAM_CC_CSIPHY0_CLK] = &cam_cc_csiphy0_clk.clkr,
+ [CAM_CC_CSIPHY1_CLK] = &cam_cc_csiphy1_clk.clkr,
+ [CAM_CC_CSIPHY2_CLK] = &cam_cc_csiphy2_clk.clkr,
+ [CAM_CC_CSIPHY3_CLK] = &cam_cc_csiphy3_clk.clkr,
+ [CAM_CC_CSIPHY4_CLK] = &cam_cc_csiphy4_clk.clkr,
+ [CAM_CC_CSIPHY5_CLK] = &cam_cc_csiphy5_clk.clkr,
+ [CAM_CC_DRV_AHB_CLK] = &cam_cc_drv_ahb_clk.clkr,
+ [CAM_CC_DRV_XO_CLK] = &cam_cc_drv_xo_clk.clkr,
+ [CAM_CC_FAST_AHB_CLK_SRC] = &cam_cc_fast_ahb_clk_src.clkr,
+ [CAM_CC_ICP_0_AHB_CLK] = &cam_cc_icp_0_ahb_clk.clkr,
+ [CAM_CC_ICP_0_CLK] = &cam_cc_icp_0_clk.clkr,
+ [CAM_CC_ICP_0_CLK_SRC] = &cam_cc_icp_0_clk_src.clkr,
+ [CAM_CC_ICP_1_AHB_CLK] = &cam_cc_icp_1_ahb_clk.clkr,
+ [CAM_CC_ICP_1_CLK] = &cam_cc_icp_1_clk.clkr,
+ [CAM_CC_ICP_1_CLK_SRC] = &cam_cc_icp_1_clk_src.clkr,
+ [CAM_CC_IFE_LITE_AHB_CLK] = &cam_cc_ife_lite_ahb_clk.clkr,
+ [CAM_CC_IFE_LITE_CLK] = &cam_cc_ife_lite_clk.clkr,
+ [CAM_CC_IFE_LITE_CLK_SRC] = &cam_cc_ife_lite_clk_src.clkr,
+ [CAM_CC_IFE_LITE_CPHY_RX_CLK] = &cam_cc_ife_lite_cphy_rx_clk.clkr,
+ [CAM_CC_IFE_LITE_CSID_CLK] = &cam_cc_ife_lite_csid_clk.clkr,
+ [CAM_CC_IFE_LITE_CSID_CLK_SRC] = &cam_cc_ife_lite_csid_clk_src.clkr,
+ [CAM_CC_IPE_NPS_AHB_CLK] = &cam_cc_ipe_nps_ahb_clk.clkr,
+ [CAM_CC_IPE_NPS_CLK] = &cam_cc_ipe_nps_clk.clkr,
+ [CAM_CC_IPE_NPS_CLK_SRC] = &cam_cc_ipe_nps_clk_src.clkr,
+ [CAM_CC_IPE_NPS_FAST_AHB_CLK] = &cam_cc_ipe_nps_fast_ahb_clk.clkr,
+ [CAM_CC_IPE_PPS_CLK] = &cam_cc_ipe_pps_clk.clkr,
+ [CAM_CC_IPE_PPS_FAST_AHB_CLK] = &cam_cc_ipe_pps_fast_ahb_clk.clkr,
+ [CAM_CC_JPEG_0_CLK] = &cam_cc_jpeg_0_clk.clkr,
+ [CAM_CC_JPEG_1_CLK] = &cam_cc_jpeg_1_clk.clkr,
+ [CAM_CC_JPEG_CLK_SRC] = &cam_cc_jpeg_clk_src.clkr,
+ [CAM_CC_OFE_AHB_CLK] = &cam_cc_ofe_ahb_clk.clkr,
+ [CAM_CC_OFE_ANCHOR_CLK] = &cam_cc_ofe_anchor_clk.clkr,
+ [CAM_CC_OFE_ANCHOR_FAST_AHB_CLK] = &cam_cc_ofe_anchor_fast_ahb_clk.clkr,
+ [CAM_CC_OFE_CLK_SRC] = &cam_cc_ofe_clk_src.clkr,
+ [CAM_CC_OFE_HDR_CLK] = &cam_cc_ofe_hdr_clk.clkr,
+ [CAM_CC_OFE_HDR_FAST_AHB_CLK] = &cam_cc_ofe_hdr_fast_ahb_clk.clkr,
+ [CAM_CC_OFE_MAIN_CLK] = &cam_cc_ofe_main_clk.clkr,
+ [CAM_CC_OFE_MAIN_FAST_AHB_CLK] = &cam_cc_ofe_main_fast_ahb_clk.clkr,
+ [CAM_CC_PLL0] = &cam_cc_pll0.clkr,
+ [CAM_CC_PLL0_OUT_EVEN] = &cam_cc_pll0_out_even.clkr,
+ [CAM_CC_PLL0_OUT_ODD] = &cam_cc_pll0_out_odd.clkr,
+ [CAM_CC_PLL1] = &cam_cc_pll1.clkr,
+ [CAM_CC_PLL1_OUT_EVEN] = &cam_cc_pll1_out_even.clkr,
+ [CAM_CC_PLL2] = &cam_cc_pll2.clkr,
+ [CAM_CC_PLL2_OUT_EVEN] = &cam_cc_pll2_out_even.clkr,
+ [CAM_CC_PLL3] = &cam_cc_pll3.clkr,
+ [CAM_CC_PLL3_OUT_EVEN] = &cam_cc_pll3_out_even.clkr,
+ [CAM_CC_PLL4] = &cam_cc_pll4.clkr,
+ [CAM_CC_PLL4_OUT_EVEN] = &cam_cc_pll4_out_even.clkr,
+ [CAM_CC_PLL5] = &cam_cc_pll5.clkr,
+ [CAM_CC_PLL5_OUT_EVEN] = &cam_cc_pll5_out_even.clkr,
+ [CAM_CC_PLL6] = &cam_cc_pll6.clkr,
+ [CAM_CC_PLL6_OUT_EVEN] = &cam_cc_pll6_out_even.clkr,
+ [CAM_CC_PLL6_OUT_ODD] = &cam_cc_pll6_out_odd.clkr,
+ [CAM_CC_QDSS_DEBUG_CLK] = &cam_cc_qdss_debug_clk.clkr,
+ [CAM_CC_QDSS_DEBUG_CLK_SRC] = &cam_cc_qdss_debug_clk_src.clkr,
+ [CAM_CC_QDSS_DEBUG_XO_CLK] = &cam_cc_qdss_debug_xo_clk.clkr,
+ [CAM_CC_SLEEP_CLK_SRC] = &cam_cc_sleep_clk_src.clkr,
+ [CAM_CC_SLOW_AHB_CLK_SRC] = &cam_cc_slow_ahb_clk_src.clkr,
+ [CAM_CC_TFE_0_BAYER_CLK] = &cam_cc_tfe_0_bayer_clk.clkr,
+ [CAM_CC_TFE_0_BAYER_FAST_AHB_CLK] = &cam_cc_tfe_0_bayer_fast_ahb_clk.clkr,
+ [CAM_CC_TFE_0_CLK_SRC] = &cam_cc_tfe_0_clk_src.clkr,
+ [CAM_CC_TFE_0_MAIN_CLK] = &cam_cc_tfe_0_main_clk.clkr,
+ [CAM_CC_TFE_0_MAIN_FAST_AHB_CLK] = &cam_cc_tfe_0_main_fast_ahb_clk.clkr,
+ [CAM_CC_TFE_1_BAYER_CLK] = &cam_cc_tfe_1_bayer_clk.clkr,
+ [CAM_CC_TFE_1_BAYER_FAST_AHB_CLK] = &cam_cc_tfe_1_bayer_fast_ahb_clk.clkr,
+ [CAM_CC_TFE_1_CLK_SRC] = &cam_cc_tfe_1_clk_src.clkr,
+ [CAM_CC_TFE_1_MAIN_CLK] = &cam_cc_tfe_1_main_clk.clkr,
+ [CAM_CC_TFE_1_MAIN_FAST_AHB_CLK] = &cam_cc_tfe_1_main_fast_ahb_clk.clkr,
+ [CAM_CC_TFE_2_BAYER_CLK] = &cam_cc_tfe_2_bayer_clk.clkr,
+ [CAM_CC_TFE_2_BAYER_FAST_AHB_CLK] = &cam_cc_tfe_2_bayer_fast_ahb_clk.clkr,
+ [CAM_CC_TFE_2_CLK_SRC] = &cam_cc_tfe_2_clk_src.clkr,
+ [CAM_CC_TFE_2_MAIN_CLK] = &cam_cc_tfe_2_main_clk.clkr,
+ [CAM_CC_TFE_2_MAIN_FAST_AHB_CLK] = &cam_cc_tfe_2_main_fast_ahb_clk.clkr,
+ [CAM_CC_XO_CLK_SRC] = &cam_cc_xo_clk_src.clkr,
+};
+
+static struct gdsc *cam_cc_eliza_gdscs[] = {
+ [CAM_CC_IPE_0_GDSC] = &cam_cc_ipe_0_gdsc,
+ [CAM_CC_OFE_GDSC] = &cam_cc_ofe_gdsc,
+ [CAM_CC_TFE_0_GDSC] = &cam_cc_tfe_0_gdsc,
+ [CAM_CC_TFE_1_GDSC] = &cam_cc_tfe_1_gdsc,
+ [CAM_CC_TFE_2_GDSC] = &cam_cc_tfe_2_gdsc,
+ [CAM_CC_TITAN_TOP_GDSC] = &cam_cc_titan_top_gdsc,
+};
+
+static const struct qcom_reset_map cam_cc_eliza_resets[] = {
+ [CAM_CC_DRV_BCR] = { 0x113bc },
+ [CAM_CC_ICP_BCR] = { 0x11210 },
+ [CAM_CC_IPE_0_BCR] = { 0x10178 },
+ [CAM_CC_OFE_BCR] = { 0x100c4 },
+ [CAM_CC_QDSS_DEBUG_BCR] = { 0x11328 },
+ [CAM_CC_TFE_0_BCR] = { 0x11000 },
+ [CAM_CC_TFE_1_BCR] = { 0x11080 },
+ [CAM_CC_TFE_2_BCR] = { 0x110e8 },
+};
+
+static struct clk_alpha_pll *cam_cc_eliza_plls[] = {
+ &cam_cc_pll0,
+ &cam_cc_pll1,
+ &cam_cc_pll2,
+ &cam_cc_pll3,
+ &cam_cc_pll4,
+ &cam_cc_pll5,
+ &cam_cc_pll6,
+};
+
+static const u32 cam_cc_eliza_critical_cbcrs[] = {
+ 0x1137c, /* CAM_CC_GDSC_CLK */
+ 0x11398, /* CAM_CC_SLEEP_CLK */
+};
+
+static const struct regmap_config cam_cc_eliza_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = 0x1601c,
+ .fast_io = true,
+};
+
+static const struct qcom_cc_driver_data cam_cc_eliza_driver_data = {
+ .alpha_plls = cam_cc_eliza_plls,
+ .num_alpha_plls = ARRAY_SIZE(cam_cc_eliza_plls),
+ .clk_cbcrs = cam_cc_eliza_critical_cbcrs,
+ .num_clk_cbcrs = ARRAY_SIZE(cam_cc_eliza_critical_cbcrs),
+};
+
+static const struct qcom_cc_desc cam_cc_eliza_desc = {
+ .config = &cam_cc_eliza_regmap_config,
+ .clks = cam_cc_eliza_clocks,
+ .num_clks = ARRAY_SIZE(cam_cc_eliza_clocks),
+ .resets = cam_cc_eliza_resets,
+ .num_resets = ARRAY_SIZE(cam_cc_eliza_resets),
+ .gdscs = cam_cc_eliza_gdscs,
+ .num_gdscs = ARRAY_SIZE(cam_cc_eliza_gdscs),
+ .use_rpm = true,
+ .driver_data = &cam_cc_eliza_driver_data,
+};
+
+static const struct of_device_id cam_cc_eliza_match_table[] = {
+ { .compatible = "qcom,eliza-camcc" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, cam_cc_eliza_match_table);
+
+static int cam_cc_eliza_probe(struct platform_device *pdev)
+{
+ return qcom_cc_probe(pdev, &cam_cc_eliza_desc);
+}
+
+static struct platform_driver cam_cc_eliza_driver = {
+ .probe = cam_cc_eliza_probe,
+ .driver = {
+ .name = "camcc-eliza",
+ .of_match_table = cam_cc_eliza_match_table,
+ },
+};
+
+module_platform_driver(cam_cc_eliza_driver);
+
+MODULE_DESCRIPTION("QTI CAMCC Eliza Driver");
+MODULE_LICENSE("GPL");
--
2.34.1
^ permalink raw reply related
* [PATCH v8 08/10] clk: qcom: gpucc: Add GPU Clock Controller driver for Eliza
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das
In-Reply-To: <20260717-b4-eliza_mm_cc_v6-v8-0-5cca1bef2e48@oss.qualcomm.com>
Add Graphics Clock Controller (GPUCC) support for Eliza platform.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
drivers/clk/qcom/Kconfig | 10 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/gpucc-eliza.c | 606 +++++++++++++++++++++++++++++++++++++++++
3 files changed, 617 insertions(+)
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 6a2a8d07f341cd8143dc1cde4534673c6eba59f4..373f925638bb026f38b8cd770760c7a9dfac684d 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -37,6 +37,16 @@ config CLK_ELIZA_GCC
Say Y if you want to use peripheral devices such as UART, SPI,
I2C, USB, UFS, SDCC, etc.
+config CLK_ELIZA_GPUCC
+ tristate "Eliza Graphics Clock Controller"
+ depends on ARM64 || COMPILE_TEST
+ select CLK_ELIZA_GCC
+ default m if ARCH_QCOM
+ help
+ Support for the graphics clock controller on Eliza devices.
+ Say Y if you want to support graphics controller devices and
+ functionality such as 3D graphics.
+
config CLK_ELIZA_TCSRCC
tristate "Eliza TCSR Clock Controller"
depends on ARM64 || COMPILE_TEST
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 36c09964879e9be09e92329fe316f67c7d4564a3..3c30b7b47d567884b4649cb13187ab2f0d77999a 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -22,6 +22,7 @@ obj-$(CONFIG_APQ_GCC_8084) += gcc-apq8084.o
obj-$(CONFIG_APQ_MMCC_8084) += mmcc-apq8084.o
obj-$(CONFIG_CLK_ELIZA_DISPCC) += dispcc-eliza.o
obj-$(CONFIG_CLK_ELIZA_GCC) += gcc-eliza.o
+obj-$(CONFIG_CLK_ELIZA_GPUCC) += gpucc-eliza.o
obj-$(CONFIG_CLK_ELIZA_TCSRCC) += tcsrcc-eliza.o
obj-$(CONFIG_CLK_ELIZA_VIDEOCC) += videocc-eliza.o
obj-$(CONFIG_CLK_GFM_LPASS_SM8250) += lpass-gfm-sm8250.o
diff --git a/drivers/clk/qcom/gpucc-eliza.c b/drivers/clk/qcom/gpucc-eliza.c
new file mode 100644
index 0000000000000000000000000000000000000000..57a28502f3257690ac93c16e1dcb057b01db6c03
--- /dev/null
+++ b/drivers/clk/qcom/gpucc-eliza.c
@@ -0,0 +1,606 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/clock/qcom,eliza-gpucc.h>
+
+#include "clk-alpha-pll.h"
+#include "clk-branch.h"
+#include "clk-pll.h"
+#include "clk-rcg.h"
+#include "clk-regmap.h"
+#include "clk-regmap-divider.h"
+#include "clk-regmap-mux.h"
+#include "common.h"
+#include "gdsc.h"
+#include "reset.h"
+
+enum {
+ DT_BI_TCXO,
+ DT_GPLL0_OUT_MAIN,
+ DT_GPLL0_OUT_MAIN_DIV,
+};
+
+enum {
+ P_BI_TCXO,
+ P_BI_TCXO_AO,
+ P_GPLL0_OUT_MAIN,
+ P_GPLL0_OUT_MAIN_DIV,
+ P_GPU_CC_PLL0_OUT_MAIN,
+ P_GPU_CC_PLL1_OUT_MAIN,
+};
+
+static const struct pll_vco lucid_ole_vco[] = {
+ { 249600000, 2300000000, 0 },
+};
+
+/* 518.0 MHz Configuration */
+static const struct alpha_pll_config gpu_cc_pll0_config = {
+ .l = 0x1a,
+ .alpha = 0xfaaa,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00182261,
+ .config_ctl_hi1_val = 0x82aa299c,
+ .test_ctl_val = 0x00000000,
+ .test_ctl_hi_val = 0x00000003,
+ .test_ctl_hi1_val = 0x00009000,
+ .test_ctl_hi2_val = 0x00000034,
+ .user_ctl_val = 0x00000000,
+ .user_ctl_hi_val = 0x00000005,
+};
+
+static struct clk_alpha_pll gpu_cc_pll0 = {
+ .offset = 0x0,
+ .config = &gpu_cc_pll0_config,
+ .vco_table = lucid_ole_vco,
+ .num_vco = ARRAY_SIZE(lucid_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_pll0",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_lucid_evo_ops,
+ },
+ },
+};
+
+/* 440.0 MHz Configuration */
+static const struct alpha_pll_config gpu_cc_pll1_config = {
+ .l = 0x16,
+ .alpha = 0xeaaa,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00182261,
+ .config_ctl_hi1_val = 0x82aa299c,
+ .test_ctl_val = 0x00000000,
+ .test_ctl_hi_val = 0x00000003,
+ .test_ctl_hi1_val = 0x00009000,
+ .test_ctl_hi2_val = 0x00000034,
+ .user_ctl_val = 0x00000000,
+ .user_ctl_hi_val = 0x00000005,
+};
+
+static struct clk_alpha_pll gpu_cc_pll1 = {
+ .offset = 0x1000,
+ .config = &gpu_cc_pll1_config,
+ .vco_table = lucid_ole_vco,
+ .num_vco = ARRAY_SIZE(lucid_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_pll1",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_lucid_evo_ops,
+ },
+ },
+};
+
+static const struct parent_map gpu_cc_parent_map_0[] = {
+ { P_BI_TCXO, 0 },
+ { P_GPLL0_OUT_MAIN, 5 },
+ { P_GPLL0_OUT_MAIN_DIV, 6 },
+};
+
+static const struct clk_parent_data gpu_cc_parent_data_0[] = {
+ { .index = DT_BI_TCXO },
+ { .index = DT_GPLL0_OUT_MAIN },
+ { .index = DT_GPLL0_OUT_MAIN_DIV },
+};
+
+static const struct parent_map gpu_cc_parent_map_1[] = {
+ { P_BI_TCXO, 0 },
+ { P_GPU_CC_PLL0_OUT_MAIN, 1 },
+ { P_GPU_CC_PLL1_OUT_MAIN, 3 },
+ { P_GPLL0_OUT_MAIN, 5 },
+ { P_GPLL0_OUT_MAIN_DIV, 6 },
+};
+
+static const struct clk_parent_data gpu_cc_parent_data_1[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &gpu_cc_pll0.clkr.hw },
+ { .hw = &gpu_cc_pll1.clkr.hw },
+ { .index = DT_GPLL0_OUT_MAIN },
+ { .index = DT_GPLL0_OUT_MAIN_DIV },
+};
+
+static const struct parent_map gpu_cc_parent_map_2[] = {
+ { P_BI_TCXO, 0 },
+ { P_GPU_CC_PLL1_OUT_MAIN, 3 },
+ { P_GPLL0_OUT_MAIN, 5 },
+ { P_GPLL0_OUT_MAIN_DIV, 6 },
+};
+
+static const struct clk_parent_data gpu_cc_parent_data_2[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &gpu_cc_pll1.clkr.hw },
+ { .index = DT_GPLL0_OUT_MAIN },
+ { .index = DT_GPLL0_OUT_MAIN_DIV },
+};
+
+static const struct parent_map gpu_cc_parent_map_3[] = {
+ { P_BI_TCXO, 0 },
+};
+
+static const struct clk_parent_data gpu_cc_parent_data_3[] = {
+ { .index = DT_BI_TCXO },
+};
+
+static const struct freq_tbl ftbl_gpu_cc_ff_clk_src[] = {
+ F(200000000, P_GPLL0_OUT_MAIN, 3, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 gpu_cc_ff_clk_src = {
+ .cmd_rcgr = 0x94b8,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = gpu_cc_parent_map_0,
+ .freq_tbl = ftbl_gpu_cc_ff_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_ff_clk_src",
+ .parent_data = gpu_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(gpu_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_gpu_cc_gmu_clk_src[] = {
+ F(220000000, P_GPU_CC_PLL1_OUT_MAIN, 2, 0, 0),
+ F(550000000, P_GPU_CC_PLL1_OUT_MAIN, 2, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 gpu_cc_gmu_clk_src = {
+ .cmd_rcgr = 0x935c,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = gpu_cc_parent_map_1,
+ .freq_tbl = ftbl_gpu_cc_gmu_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_gmu_clk_src",
+ .parent_data = gpu_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(gpu_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 gpu_cc_hub_clk_src = {
+ .cmd_rcgr = 0x9430,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = gpu_cc_parent_map_2,
+ .freq_tbl = ftbl_gpu_cc_ff_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_hub_clk_src",
+ .parent_data = gpu_cc_parent_data_2,
+ .num_parents = ARRAY_SIZE(gpu_cc_parent_data_2),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_gpu_cc_xo_clk_src[] = {
+ F(19200000, P_BI_TCXO, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 gpu_cc_xo_clk_src = {
+ .cmd_rcgr = 0x9010,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = gpu_cc_parent_map_3,
+ .freq_tbl = ftbl_gpu_cc_xo_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_xo_clk_src",
+ .parent_data = gpu_cc_parent_data_3,
+ .num_parents = ARRAY_SIZE(gpu_cc_parent_data_3),
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_regmap_div gpu_cc_xo_div_clk_src = {
+ .reg = 0x9050,
+ .shift = 0,
+ .width = 4,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_xo_div_clk_src",
+ .parent_hws = (const struct clk_hw*[]) {
+ &gpu_cc_xo_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .ops = &clk_regmap_div_ro_ops,
+ },
+};
+
+static struct clk_branch gpu_cc_ahb_clk = {
+ .halt_reg = 0x914c,
+ .halt_check = BRANCH_HALT_DELAY,
+ .clkr = {
+ .enable_reg = 0x914c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &gpu_cc_hub_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_crc_ahb_clk = {
+ .halt_reg = 0x9150,
+ .halt_check = BRANCH_HALT_VOTED,
+ .clkr = {
+ .enable_reg = 0x9150,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_crc_ahb_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &gpu_cc_hub_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_cx_accu_shift_clk = {
+ .halt_reg = 0x9480,
+ .halt_check = BRANCH_HALT_VOTED,
+ .clkr = {
+ .enable_reg = 0x9480,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_cx_accu_shift_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &gpu_cc_xo_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_cx_ff_clk = {
+ .halt_reg = 0x9184,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x9184,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_cx_ff_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &gpu_cc_ff_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_cx_gmu_clk = {
+ .halt_reg = 0x916c,
+ .halt_check = BRANCH_HALT_VOTED,
+ .clkr = {
+ .enable_reg = 0x916c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_cx_gmu_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &gpu_cc_gmu_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_aon_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_cxo_clk = {
+ .halt_reg = 0x917c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x917c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_cxo_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &gpu_cc_xo_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_freq_measure_clk = {
+ .halt_reg = 0x9008,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x9008,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_freq_measure_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &gpu_cc_xo_div_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_hlos1_vote_gpu_smmu_clk = {
+ .halt_reg = 0x7000,
+ .halt_check = BRANCH_HALT_VOTED,
+ .clkr = {
+ .enable_reg = 0x7000,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_hlos1_vote_gpu_smmu_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_hub_aon_clk = {
+ .halt_reg = 0x942c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x942c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_hub_aon_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &gpu_cc_hub_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_aon_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_hub_cx_int_clk = {
+ .halt_reg = 0x9180,
+ .halt_check = BRANCH_HALT_VOTED,
+ .clkr = {
+ .enable_reg = 0x9180,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_hub_cx_int_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &gpu_cc_hub_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_aon_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_memnoc_gfx_clk = {
+ .halt_reg = 0x9188,
+ .halt_check = BRANCH_HALT_VOTED,
+ .clkr = {
+ .enable_reg = 0x9188,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_memnoc_gfx_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_mnd1x_0_gfx3d_clk = {
+ .halt_reg = 0x92cc,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x92cc,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_mnd1x_0_gfx3d_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_mnd1x_1_gfx3d_clk = {
+ .halt_reg = 0x92d0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x92d0,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_mnd1x_1_gfx3d_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch gpu_cc_sleep_clk = {
+ .halt_reg = 0x9164,
+ .halt_check = BRANCH_HALT_VOTED,
+ .clkr = {
+ .enable_reg = 0x9164,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "gpu_cc_sleep_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct gdsc gpu_cc_cx_gdsc = {
+ .gdscr = 0x9110,
+ .gds_hw_ctrl = 0x9124,
+ .en_rest_wait_val = 0x2,
+ .en_few_wait_val = 0x2,
+ .clk_dis_wait_val = 0x8,
+ .pd = {
+ .name = "gpu_cc_cx_gdsc",
+ },
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = VOTABLE | RETAIN_FF_ENABLE,
+};
+
+static struct gdsc gpu_cc_gx_gdsc = {
+ .gdscr = 0x905c,
+ .en_rest_wait_val = 0x2,
+ .en_few_wait_val = 0x2,
+ .clk_dis_wait_val = 0xf,
+ .pd = {
+ .name = "gpu_cc_gx_gdsc",
+ .power_on = gdsc_gx_do_nothing_enable,
+ },
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = POLL_CFG_GDSCR | RETAIN_FF_ENABLE,
+};
+
+static struct clk_regmap *gpu_cc_eliza_clocks[] = {
+ [GPU_CC_AHB_CLK] = &gpu_cc_ahb_clk.clkr,
+ [GPU_CC_CRC_AHB_CLK] = &gpu_cc_crc_ahb_clk.clkr,
+ [GPU_CC_CX_ACCU_SHIFT_CLK] = &gpu_cc_cx_accu_shift_clk.clkr,
+ [GPU_CC_CX_FF_CLK] = &gpu_cc_cx_ff_clk.clkr,
+ [GPU_CC_CX_GMU_CLK] = &gpu_cc_cx_gmu_clk.clkr,
+ [GPU_CC_CXO_CLK] = &gpu_cc_cxo_clk.clkr,
+ [GPU_CC_FF_CLK_SRC] = &gpu_cc_ff_clk_src.clkr,
+ [GPU_CC_FREQ_MEASURE_CLK] = &gpu_cc_freq_measure_clk.clkr,
+ [GPU_CC_GMU_CLK_SRC] = &gpu_cc_gmu_clk_src.clkr,
+ [GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK] = &gpu_cc_hlos1_vote_gpu_smmu_clk.clkr,
+ [GPU_CC_HUB_AON_CLK] = &gpu_cc_hub_aon_clk.clkr,
+ [GPU_CC_HUB_CLK_SRC] = &gpu_cc_hub_clk_src.clkr,
+ [GPU_CC_HUB_CX_INT_CLK] = &gpu_cc_hub_cx_int_clk.clkr,
+ [GPU_CC_MEMNOC_GFX_CLK] = &gpu_cc_memnoc_gfx_clk.clkr,
+ [GPU_CC_MND1X_0_GFX3D_CLK] = &gpu_cc_mnd1x_0_gfx3d_clk.clkr,
+ [GPU_CC_MND1X_1_GFX3D_CLK] = &gpu_cc_mnd1x_1_gfx3d_clk.clkr,
+ [GPU_CC_PLL0] = &gpu_cc_pll0.clkr,
+ [GPU_CC_PLL1] = &gpu_cc_pll1.clkr,
+ [GPU_CC_SLEEP_CLK] = &gpu_cc_sleep_clk.clkr,
+ [GPU_CC_XO_CLK_SRC] = &gpu_cc_xo_clk_src.clkr,
+ [GPU_CC_XO_DIV_CLK_SRC] = &gpu_cc_xo_div_clk_src.clkr,
+};
+
+static struct gdsc *gpu_cc_eliza_gdscs[] = {
+ [GPU_CC_CX_GDSC] = &gpu_cc_cx_gdsc,
+ [GPU_CC_GX_GDSC] = &gpu_cc_gx_gdsc,
+};
+
+static const struct qcom_reset_map gpu_cc_eliza_resets[] = {
+ [GPU_CC_ACD_BCR] = { 0x939c },
+ [GPU_CC_CB_BCR] = { 0x93e4 },
+ [GPU_CC_CX_BCR] = { 0x910c },
+ [GPU_CC_FAST_HUB_BCR] = { 0x9428 },
+ [GPU_CC_FF_BCR] = { 0x94b4 },
+ [GPU_CC_GFX3D_AON_BCR] = { 0x91dc },
+ [GPU_CC_GMU_BCR] = { 0x9358 },
+ [GPU_CC_GX_BCR] = { 0x9058 },
+ [GPU_CC_RBCPR_BCR] = { 0x9224 },
+ [GPU_CC_XO_BCR] = { 0x9000 },
+};
+
+static struct clk_alpha_pll *gpu_cc_eliza_plls[] = {
+ &gpu_cc_pll0,
+ &gpu_cc_pll1,
+};
+
+static const u32 gpu_cc_eliza_critical_cbcrs[] = {
+ 0x9004, /* GPU_CC_CXO_AON_CLK */
+ 0x900c, /* GPU_CC_DEMET_CLK */
+};
+
+static const struct regmap_config gpu_cc_eliza_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = 0x9988,
+ .fast_io = true,
+};
+
+static const struct qcom_cc_driver_data gpu_cc_eliza_driver_data = {
+ .alpha_plls = gpu_cc_eliza_plls,
+ .num_alpha_plls = ARRAY_SIZE(gpu_cc_eliza_plls),
+ .clk_cbcrs = gpu_cc_eliza_critical_cbcrs,
+ .num_clk_cbcrs = ARRAY_SIZE(gpu_cc_eliza_critical_cbcrs),
+};
+
+static const struct qcom_cc_desc gpu_cc_eliza_desc = {
+ .config = &gpu_cc_eliza_regmap_config,
+ .clks = gpu_cc_eliza_clocks,
+ .num_clks = ARRAY_SIZE(gpu_cc_eliza_clocks),
+ .resets = gpu_cc_eliza_resets,
+ .num_resets = ARRAY_SIZE(gpu_cc_eliza_resets),
+ .gdscs = gpu_cc_eliza_gdscs,
+ .num_gdscs = ARRAY_SIZE(gpu_cc_eliza_gdscs),
+ .use_rpm = true,
+ .driver_data = &gpu_cc_eliza_driver_data,
+};
+
+static const struct of_device_id gpu_cc_eliza_match_table[] = {
+ { .compatible = "qcom,eliza-gpucc" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, gpu_cc_eliza_match_table);
+
+static int gpu_cc_eliza_probe(struct platform_device *pdev)
+{
+ return qcom_cc_probe(pdev, &gpu_cc_eliza_desc);
+}
+
+static struct platform_driver gpu_cc_eliza_driver = {
+ .probe = gpu_cc_eliza_probe,
+ .driver = {
+ .name = "gpucc-eliza",
+ .of_match_table = gpu_cc_eliza_match_table,
+ },
+};
+
+module_platform_driver(gpu_cc_eliza_driver);
+
+MODULE_DESCRIPTION("QTI GPUCC Eliza Driver");
+MODULE_LICENSE("GPL");
--
2.34.1
^ permalink raw reply related
* [PATCH v8 07/10] clk: qcom: videocc: Add video clock controller driver for Eliza
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das
In-Reply-To: <20260717-b4-eliza_mm_cc_v6-v8-0-5cca1bef2e48@oss.qualcomm.com>
Add support for the video clock controller for video clients to be able
to request for videocc clocks on Eliza platform.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
drivers/clk/qcom/Kconfig | 10 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/videocc-eliza.c | 404 +++++++++++++++++++++++++++++++++++++++
3 files changed, 415 insertions(+)
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index d9cff5b0281d8cc373b8ab14683370cb9b7f8bf3..6a2a8d07f341cd8143dc1cde4534673c6eba59f4 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -45,6 +45,16 @@ config CLK_ELIZA_TCSRCC
Support for the TCSR clock controller on Eliza devices.
Say Y if you want to use peripheral devices such as USB/PCIe/UFS.
+config CLK_ELIZA_VIDEOCC
+ tristate "Eliza Video Clock Controller"
+ depends on ARM64 || COMPILE_TEST
+ select CLK_ELIZA_GCC
+ default m if ARCH_QCOM
+ help
+ Support for the video clock controller on Eliza devices.
+ Say Y if you want to support video devices and functionality such as
+ video encode and decode.
+
config CLK_GLYMUR_DISPCC
tristate "Glymur Display Clock Controller"
depends on ARM64 || COMPILE_TEST
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index e100cfd6a52de9f88f11720d9c2043db5e553618..36c09964879e9be09e92329fe316f67c7d4564a3 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_APQ_MMCC_8084) += mmcc-apq8084.o
obj-$(CONFIG_CLK_ELIZA_DISPCC) += dispcc-eliza.o
obj-$(CONFIG_CLK_ELIZA_GCC) += gcc-eliza.o
obj-$(CONFIG_CLK_ELIZA_TCSRCC) += tcsrcc-eliza.o
+obj-$(CONFIG_CLK_ELIZA_VIDEOCC) += videocc-eliza.o
obj-$(CONFIG_CLK_GFM_LPASS_SM8250) += lpass-gfm-sm8250.o
obj-$(CONFIG_CLK_GLYMUR_DISPCC) += dispcc-glymur.o
obj-$(CONFIG_CLK_GLYMUR_GCC) += gcc-glymur.o
diff --git a/drivers/clk/qcom/videocc-eliza.c b/drivers/clk/qcom/videocc-eliza.c
new file mode 100644
index 0000000000000000000000000000000000000000..9112ded781c235473bcbd8b8c735283c7d058922
--- /dev/null
+++ b/drivers/clk/qcom/videocc-eliza.c
@@ -0,0 +1,404 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/clock/qcom,eliza-videocc.h>
+
+#include "clk-alpha-pll.h"
+#include "clk-branch.h"
+#include "clk-pll.h"
+#include "clk-rcg.h"
+#include "clk-regmap.h"
+#include "clk-regmap-divider.h"
+#include "clk-regmap-mux.h"
+#include "common.h"
+#include "gdsc.h"
+#include "reset.h"
+
+enum {
+ DT_BI_TCXO,
+ DT_BI_TCXO_AO,
+ DT_SLEEP_CLK,
+ DT_AHB_CLK,
+};
+
+enum {
+ P_BI_TCXO,
+ P_SLEEP_CLK,
+ P_VIDEO_CC_PLL0_OUT_MAIN,
+};
+
+static const struct pll_vco lucid_ole_vco[] = {
+ { 249600000, 2300000000, 0 },
+};
+
+/* 576.0 MHz Configuration */
+static const struct alpha_pll_config video_cc_pll0_config = {
+ .l = 0x1e,
+ .alpha = 0x0,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00182261,
+ .config_ctl_hi1_val = 0x82aa299c,
+ .test_ctl_val = 0x00000000,
+ .test_ctl_hi_val = 0x00000003,
+ .test_ctl_hi1_val = 0x00009000,
+ .test_ctl_hi2_val = 0x00000034,
+ .user_ctl_val = 0x00000000,
+ .user_ctl_hi_val = 0x00000005,
+};
+
+static struct clk_alpha_pll video_cc_pll0 = {
+ .offset = 0x0,
+ .config = &video_cc_pll0_config,
+ .vco_table = lucid_ole_vco,
+ .num_vco = ARRAY_SIZE(lucid_ole_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE],
+ .clkr = {
+ .hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_pll0",
+ .parent_data = &(const struct clk_parent_data) {
+ .index = DT_BI_TCXO,
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_lucid_evo_ops,
+ },
+ },
+};
+
+static const struct parent_map video_cc_parent_map_0[] = {
+ { P_BI_TCXO, 0 },
+};
+
+static const struct clk_parent_data video_cc_parent_data_0[] = {
+ { .index = DT_BI_TCXO },
+};
+
+static const struct parent_map video_cc_parent_map_1[] = {
+ { P_BI_TCXO, 0 },
+ { P_VIDEO_CC_PLL0_OUT_MAIN, 1 },
+};
+
+static const struct clk_parent_data video_cc_parent_data_1[] = {
+ { .index = DT_BI_TCXO },
+ { .hw = &video_cc_pll0.clkr.hw },
+};
+
+static const struct parent_map video_cc_parent_map_2[] = {
+ { P_SLEEP_CLK, 0 },
+};
+
+static const struct clk_parent_data video_cc_parent_data_2[] = {
+ { .index = DT_SLEEP_CLK },
+};
+
+static const struct freq_tbl ftbl_video_cc_ahb_clk_src[] = {
+ F(19200000, P_BI_TCXO, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 video_cc_ahb_clk_src = {
+ .cmd_rcgr = 0x8018,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = video_cc_parent_map_0,
+ .freq_tbl = ftbl_video_cc_ahb_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_ahb_clk_src",
+ .parent_data = video_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(video_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_video_cc_mvs0_clk_src[] = {
+ F(576000000, P_VIDEO_CC_PLL0_OUT_MAIN, 1, 0, 0),
+ F(633000000, P_VIDEO_CC_PLL0_OUT_MAIN, 1, 0, 0),
+ F(720000000, P_VIDEO_CC_PLL0_OUT_MAIN, 1, 0, 0),
+ F(1014000000, P_VIDEO_CC_PLL0_OUT_MAIN, 1, 0, 0),
+ F(1098000000, P_VIDEO_CC_PLL0_OUT_MAIN, 1, 0, 0),
+ F(1113000000, P_VIDEO_CC_PLL0_OUT_MAIN, 1, 0, 0),
+ F(1332000000, P_VIDEO_CC_PLL0_OUT_MAIN, 1, 0, 0),
+ F(1600000000, P_VIDEO_CC_PLL0_OUT_MAIN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 video_cc_mvs0_clk_src = {
+ .cmd_rcgr = 0x8000,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = video_cc_parent_map_1,
+ .freq_tbl = ftbl_video_cc_mvs0_clk_src,
+ .hw_clk_ctrl = true,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_mvs0_clk_src",
+ .parent_data = video_cc_parent_data_1,
+ .num_parents = ARRAY_SIZE(video_cc_parent_data_1),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_video_cc_sleep_clk_src[] = {
+ F(32000, P_SLEEP_CLK, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 video_cc_sleep_clk_src = {
+ .cmd_rcgr = 0x8110,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = video_cc_parent_map_2,
+ .freq_tbl = ftbl_video_cc_sleep_clk_src,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_sleep_clk_src",
+ .parent_data = video_cc_parent_data_2,
+ .num_parents = ARRAY_SIZE(video_cc_parent_data_2),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_rcg2 video_cc_xo_clk_src = {
+ .cmd_rcgr = 0x80f4,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = video_cc_parent_map_0,
+ .freq_tbl = ftbl_video_cc_ahb_clk_src,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_xo_clk_src",
+ .parent_data = video_cc_parent_data_0,
+ .num_parents = ARRAY_SIZE(video_cc_parent_data_0),
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_shared_ops,
+ },
+};
+
+static struct clk_regmap_div video_cc_mvs0_div_clk_src = {
+ .reg = 0x80ac,
+ .shift = 0,
+ .width = 4,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_mvs0_div_clk_src",
+ .parent_hws = (const struct clk_hw*[]) {
+ &video_cc_mvs0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_regmap_div_ro_ops,
+ },
+};
+
+static struct clk_regmap_div video_cc_mvs0c_div2_div_clk_src = {
+ .reg = 0x8058,
+ .shift = 0,
+ .width = 4,
+ .clkr.hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_mvs0c_div2_div_clk_src",
+ .parent_hws = (const struct clk_hw*[]) {
+ &video_cc_mvs0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_regmap_div_ro_ops,
+ },
+};
+
+static struct clk_branch video_cc_mvs0_clk = {
+ .halt_reg = 0x80a0,
+ .halt_check = BRANCH_HALT_VOTED,
+ .hwcg_reg = 0x80a0,
+ .hwcg_bit = 1,
+ .clkr = {
+ .enable_reg = 0x80a0,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_mvs0_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &video_cc_mvs0_div_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch video_cc_mvs0_shift_clk = {
+ .halt_reg = 0x8144,
+ .halt_check = BRANCH_HALT_VOTED,
+ .hwcg_reg = 0x8144,
+ .hwcg_bit = 1,
+ .clkr = {
+ .enable_reg = 0x8144,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_mvs0_shift_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &video_cc_xo_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch video_cc_mvs0c_clk = {
+ .halt_reg = 0x804c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x804c,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_mvs0c_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &video_cc_mvs0c_div2_div_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch video_cc_mvs0c_shift_clk = {
+ .halt_reg = 0x8148,
+ .halt_check = BRANCH_HALT_VOTED,
+ .hwcg_reg = 0x8148,
+ .hwcg_bit = 1,
+ .clkr = {
+ .enable_reg = 0x8148,
+ .enable_mask = BIT(0),
+ .hw.init = &(const struct clk_init_data) {
+ .name = "video_cc_mvs0c_shift_clk",
+ .parent_hws = (const struct clk_hw*[]) {
+ &video_cc_xo_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct gdsc video_cc_mvs0c_gdsc = {
+ .gdscr = 0x8034,
+ .en_rest_wait_val = 0x2,
+ .en_few_wait_val = 0x2,
+ .clk_dis_wait_val = 0x6,
+ .pd = {
+ .name = "video_cc_mvs0c_gdsc",
+ },
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = POLL_CFG_GDSCR | RETAIN_FF_ENABLE,
+};
+
+static struct gdsc video_cc_mvs0_gdsc = {
+ .gdscr = 0x808c,
+ .en_rest_wait_val = 0x2,
+ .en_few_wait_val = 0x2,
+ .clk_dis_wait_val = 0x6,
+ .pd = {
+ .name = "video_cc_mvs0_gdsc",
+ },
+ .pwrsts = PWRSTS_OFF_ON,
+ .parent = &video_cc_mvs0c_gdsc.pd,
+ .flags = POLL_CFG_GDSCR | RETAIN_FF_ENABLE | HW_CTRL_TRIGGER,
+};
+
+static struct clk_regmap *video_cc_eliza_clocks[] = {
+ [VIDEO_CC_AHB_CLK_SRC] = &video_cc_ahb_clk_src.clkr,
+ [VIDEO_CC_MVS0_CLK] = &video_cc_mvs0_clk.clkr,
+ [VIDEO_CC_MVS0_CLK_SRC] = &video_cc_mvs0_clk_src.clkr,
+ [VIDEO_CC_MVS0_DIV_CLK_SRC] = &video_cc_mvs0_div_clk_src.clkr,
+ [VIDEO_CC_MVS0_SHIFT_CLK] = &video_cc_mvs0_shift_clk.clkr,
+ [VIDEO_CC_MVS0C_CLK] = &video_cc_mvs0c_clk.clkr,
+ [VIDEO_CC_MVS0C_DIV2_DIV_CLK_SRC] = &video_cc_mvs0c_div2_div_clk_src.clkr,
+ [VIDEO_CC_MVS0C_SHIFT_CLK] = &video_cc_mvs0c_shift_clk.clkr,
+ [VIDEO_CC_PLL0] = &video_cc_pll0.clkr,
+ [VIDEO_CC_SLEEP_CLK_SRC] = &video_cc_sleep_clk_src.clkr,
+ [VIDEO_CC_XO_CLK_SRC] = &video_cc_xo_clk_src.clkr,
+};
+
+static struct gdsc *video_cc_eliza_gdscs[] = {
+ [VIDEO_CC_MVS0_GDSC] = &video_cc_mvs0_gdsc,
+ [VIDEO_CC_MVS0C_GDSC] = &video_cc_mvs0c_gdsc,
+};
+
+static const struct qcom_reset_map video_cc_eliza_resets[] = {
+ [VIDEO_CC_INTERFACE_BCR] = { 0x80d8 },
+ [VIDEO_CC_MVS0_CLK_ARES] = { 0x80a0, 2 },
+ [VIDEO_CC_MVS0_BCR] = { 0x8088 },
+ [VIDEO_CC_MVS0C_CLK_ARES] = { 0x804c, 2 },
+ [VIDEO_CC_MVS0C_BCR] = { 0x8030 },
+ [VIDEO_CC_XO_CLK_ARES] = { 0x810c, 2 },
+};
+
+static struct clk_alpha_pll *video_cc_eliza_plls[] = {
+ &video_cc_pll0,
+};
+
+static const u32 video_cc_eliza_critical_cbcrs[] = {
+ 0x80dc, /* VIDEO_CC_AHB_CLK */
+ 0x8128, /* VIDEO_CC_SLEEP_CLK */
+ 0x810c, /* VIDEO_CC_XO_CLK */
+};
+
+static const struct regmap_config video_cc_eliza_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = 0x9f50,
+ .fast_io = true,
+};
+
+static const struct qcom_cc_driver_data video_cc_eliza_driver_data = {
+ .alpha_plls = video_cc_eliza_plls,
+ .num_alpha_plls = ARRAY_SIZE(video_cc_eliza_plls),
+ .clk_cbcrs = video_cc_eliza_critical_cbcrs,
+ .num_clk_cbcrs = ARRAY_SIZE(video_cc_eliza_critical_cbcrs),
+};
+
+static const struct qcom_cc_desc video_cc_eliza_desc = {
+ .config = &video_cc_eliza_regmap_config,
+ .clks = video_cc_eliza_clocks,
+ .num_clks = ARRAY_SIZE(video_cc_eliza_clocks),
+ .resets = video_cc_eliza_resets,
+ .num_resets = ARRAY_SIZE(video_cc_eliza_resets),
+ .gdscs = video_cc_eliza_gdscs,
+ .num_gdscs = ARRAY_SIZE(video_cc_eliza_gdscs),
+ .use_rpm = true,
+ .driver_data = &video_cc_eliza_driver_data,
+};
+
+static const struct of_device_id video_cc_eliza_match_table[] = {
+ { .compatible = "qcom,eliza-videocc" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, video_cc_eliza_match_table);
+
+static int video_cc_eliza_probe(struct platform_device *pdev)
+{
+ return qcom_cc_probe(pdev, &video_cc_eliza_desc);
+}
+
+static struct platform_driver video_cc_eliza_driver = {
+ .probe = video_cc_eliza_probe,
+ .driver = {
+ .name = "videocc-eliza",
+ .of_match_table = video_cc_eliza_match_table,
+ },
+};
+
+module_platform_driver(video_cc_eliza_driver);
+
+MODULE_DESCRIPTION("QTI VIDEOCC Eliza Driver");
+MODULE_LICENSE("GPL");
--
2.34.1
^ permalink raw reply related
* [PATCH v8 06/10] dt-bindings: clock: qcom: Add support for CAMCC for Eliza
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das,
Krzysztof Kozlowski
In-Reply-To: <20260717-b4-eliza_mm_cc_v6-v8-0-5cca1bef2e48@oss.qualcomm.com>
Eliza camera clock controller is on CX and MX rails similar to Milos.
Add compatible string for Eliza camera and camera BIST clock
controller to the existing Milos camcc binding and add the
dt-bindings header for Eliza.
The camera clock controller provides power domains, so 'power-domain-cells'
must be present in the device tree node. Add this to required properties
to enforce it in the binding schema.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
.../bindings/clock/qcom,milos-camcc.yaml | 12 +-
.../dt-bindings/clock/qcom,eliza-cambistmclkcc.h | 32 +++++
include/dt-bindings/clock/qcom,eliza-camcc.h | 151 +++++++++++++++++++++
3 files changed, 193 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/qcom,milos-camcc.yaml b/Documentation/devicetree/bindings/clock/qcom,milos-camcc.yaml
index 2295e7627ec9feb6a67f3ca952e6192a31cce593..29c29d9774f9c712ba39dfc1487c7118fec9dc90 100644
--- a/Documentation/devicetree/bindings/clock/qcom,milos-camcc.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,milos-camcc.yaml
@@ -8,16 +8,23 @@ title: Qualcomm Camera Clock & Reset Controller on Milos
maintainers:
- Luca Weiss <luca.weiss@fairphone.com>
+ - Taniya Das <taniya.das@oss.qualcomm.com>
description: |
Qualcomm camera clock control module provides the clocks, resets and power
domains on Milos.
- See also: include/dt-bindings/clock/qcom,milos-camcc.h
+ See also:
+ include/dt-bindings/clock/qcom,eliza-cambistmclkcc.h
+ include/dt-bindings/clock/qcom,eliza-camcc.h
+ include/dt-bindings/clock/qcom,milos-camcc.h
properties:
compatible:
- const: qcom,milos-camcc
+ enum:
+ - qcom,eliza-cambistmclkcc
+ - qcom,eliza-camcc
+ - qcom,milos-camcc
clocks:
items:
@@ -40,6 +47,7 @@ required:
- clocks
- power-domains
- required-opps
+ - '#power-domain-cells'
allOf:
- $ref: qcom,gcc.yaml#
diff --git a/include/dt-bindings/clock/qcom,eliza-cambistmclkcc.h b/include/dt-bindings/clock/qcom,eliza-cambistmclkcc.h
new file mode 100644
index 0000000000000000000000000000000000000000..7b8b285f18d2714393885149fc97c715b3fbb042
--- /dev/null
+++ b/include/dt-bindings/clock/qcom,eliza-cambistmclkcc.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#ifndef _DT_BINDINGS_CLK_QCOM_CAM_BIST_MCLK_CC_ELIZA_H
+#define _DT_BINDINGS_CLK_QCOM_CAM_BIST_MCLK_CC_ELIZA_H
+
+/* CAM_BIST_MCLK_CC clocks */
+#define CAM_BIST_MCLK_CC_MCLK0_CLK 0
+#define CAM_BIST_MCLK_CC_MCLK0_CLK_SRC 1
+#define CAM_BIST_MCLK_CC_MCLK1_CLK 2
+#define CAM_BIST_MCLK_CC_MCLK1_CLK_SRC 3
+#define CAM_BIST_MCLK_CC_MCLK2_CLK 4
+#define CAM_BIST_MCLK_CC_MCLK2_CLK_SRC 5
+#define CAM_BIST_MCLK_CC_MCLK3_CLK 6
+#define CAM_BIST_MCLK_CC_MCLK3_CLK_SRC 7
+#define CAM_BIST_MCLK_CC_MCLK4_CLK 8
+#define CAM_BIST_MCLK_CC_MCLK4_CLK_SRC 9
+#define CAM_BIST_MCLK_CC_MCLK5_CLK 10
+#define CAM_BIST_MCLK_CC_MCLK5_CLK_SRC 11
+#define CAM_BIST_MCLK_CC_MCLK6_CLK 12
+#define CAM_BIST_MCLK_CC_MCLK6_CLK_SRC 13
+#define CAM_BIST_MCLK_CC_MCLK7_CLK 14
+#define CAM_BIST_MCLK_CC_MCLK7_CLK_SRC 15
+#define CAM_BIST_MCLK_CC_PLL0 16
+#define CAM_BIST_MCLK_CC_PLL_TEST_CLK 17
+#define CAM_BIST_MCLK_CC_PLL_TEST_DIV_CLK_SRC 18
+#define CAM_BIST_MCLK_CC_SLEEP_CLK 19
+#define CAM_BIST_MCLK_CC_SLEEP_CLK_SRC 20
+
+#endif
diff --git a/include/dt-bindings/clock/qcom,eliza-camcc.h b/include/dt-bindings/clock/qcom,eliza-camcc.h
new file mode 100644
index 0000000000000000000000000000000000000000..d85ef9777d08d12ec349d57f6da5e76a305404f8
--- /dev/null
+++ b/include/dt-bindings/clock/qcom,eliza-camcc.h
@@ -0,0 +1,151 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#ifndef _DT_BINDINGS_CLK_QCOM_CAM_CC_ELIZA_H
+#define _DT_BINDINGS_CLK_QCOM_CAM_CC_ELIZA_H
+
+/* CAM_CC clocks */
+#define CAM_CC_CAM_TOP_AHB_CLK 0
+#define CAM_CC_CAM_TOP_FAST_AHB_CLK 1
+#define CAM_CC_CAMNOC_DCD_XO_CLK 2
+#define CAM_CC_CAMNOC_NRT_AXI_CLK 3
+#define CAM_CC_CAMNOC_NRT_CRE_CLK 4
+#define CAM_CC_CAMNOC_NRT_IPE_NPS_CLK 5
+#define CAM_CC_CAMNOC_NRT_OFE_ANCHOR_CLK 6
+#define CAM_CC_CAMNOC_NRT_OFE_HDR_CLK 7
+#define CAM_CC_CAMNOC_NRT_OFE_MAIN_CLK 8
+#define CAM_CC_CAMNOC_RT_AXI_CLK 9
+#define CAM_CC_CAMNOC_RT_AXI_CLK_SRC 10
+#define CAM_CC_CAMNOC_RT_IFE_LITE_CLK 11
+#define CAM_CC_CAMNOC_RT_TFE_0_BAYER_CLK 12
+#define CAM_CC_CAMNOC_RT_TFE_0_MAIN_CLK 13
+#define CAM_CC_CAMNOC_RT_TFE_1_BAYER_CLK 14
+#define CAM_CC_CAMNOC_RT_TFE_1_MAIN_CLK 15
+#define CAM_CC_CAMNOC_RT_TFE_2_BAYER_CLK 16
+#define CAM_CC_CAMNOC_RT_TFE_2_MAIN_CLK 17
+#define CAM_CC_CAMNOC_XO_CLK 18
+#define CAM_CC_CCI_0_CLK 19
+#define CAM_CC_CCI_0_CLK_SRC 20
+#define CAM_CC_CCI_1_CLK 21
+#define CAM_CC_CCI_1_CLK_SRC 22
+#define CAM_CC_CCI_2_CLK 23
+#define CAM_CC_CCI_2_CLK_SRC 24
+#define CAM_CC_CORE_AHB_CLK 25
+#define CAM_CC_CPHY_RX_CLK_SRC 26
+#define CAM_CC_CRE_AHB_CLK 27
+#define CAM_CC_CRE_CLK 28
+#define CAM_CC_CRE_CLK_SRC 29
+#define CAM_CC_CSI0PHYTIMER_CLK 30
+#define CAM_CC_CSI0PHYTIMER_CLK_SRC 31
+#define CAM_CC_CSI1PHYTIMER_CLK 32
+#define CAM_CC_CSI1PHYTIMER_CLK_SRC 33
+#define CAM_CC_CSI2PHYTIMER_CLK 34
+#define CAM_CC_CSI2PHYTIMER_CLK_SRC 35
+#define CAM_CC_CSI3PHYTIMER_CLK 36
+#define CAM_CC_CSI3PHYTIMER_CLK_SRC 37
+#define CAM_CC_CSI4PHYTIMER_CLK 38
+#define CAM_CC_CSI4PHYTIMER_CLK_SRC 39
+#define CAM_CC_CSI5PHYTIMER_CLK 40
+#define CAM_CC_CSI5PHYTIMER_CLK_SRC 41
+#define CAM_CC_CSID_CLK 42
+#define CAM_CC_CSID_CLK_SRC 43
+#define CAM_CC_CSID_CSIPHY_RX_CLK 44
+#define CAM_CC_CSIPHY0_CLK 45
+#define CAM_CC_CSIPHY1_CLK 46
+#define CAM_CC_CSIPHY2_CLK 47
+#define CAM_CC_CSIPHY3_CLK 48
+#define CAM_CC_CSIPHY4_CLK 49
+#define CAM_CC_CSIPHY5_CLK 50
+#define CAM_CC_DRV_AHB_CLK 51
+#define CAM_CC_DRV_XO_CLK 52
+#define CAM_CC_FAST_AHB_CLK_SRC 53
+#define CAM_CC_GDSC_CLK 54
+#define CAM_CC_ICP_0_AHB_CLK 55
+#define CAM_CC_ICP_0_CLK 56
+#define CAM_CC_ICP_0_CLK_SRC 57
+#define CAM_CC_ICP_1_AHB_CLK 58
+#define CAM_CC_ICP_1_CLK 59
+#define CAM_CC_ICP_1_CLK_SRC 60
+#define CAM_CC_IFE_LITE_AHB_CLK 61
+#define CAM_CC_IFE_LITE_CLK 62
+#define CAM_CC_IFE_LITE_CLK_SRC 63
+#define CAM_CC_IFE_LITE_CPHY_RX_CLK 64
+#define CAM_CC_IFE_LITE_CSID_CLK 65
+#define CAM_CC_IFE_LITE_CSID_CLK_SRC 66
+#define CAM_CC_IPE_NPS_AHB_CLK 67
+#define CAM_CC_IPE_NPS_CLK 68
+#define CAM_CC_IPE_NPS_CLK_SRC 69
+#define CAM_CC_IPE_NPS_FAST_AHB_CLK 70
+#define CAM_CC_IPE_PPS_CLK 71
+#define CAM_CC_IPE_PPS_FAST_AHB_CLK 72
+#define CAM_CC_JPEG_0_CLK 73
+#define CAM_CC_JPEG_1_CLK 74
+#define CAM_CC_JPEG_CLK_SRC 75
+#define CAM_CC_OFE_AHB_CLK 76
+#define CAM_CC_OFE_ANCHOR_CLK 77
+#define CAM_CC_OFE_ANCHOR_FAST_AHB_CLK 78
+#define CAM_CC_OFE_CLK_SRC 79
+#define CAM_CC_OFE_HDR_CLK 80
+#define CAM_CC_OFE_HDR_FAST_AHB_CLK 81
+#define CAM_CC_OFE_MAIN_CLK 82
+#define CAM_CC_OFE_MAIN_FAST_AHB_CLK 83
+#define CAM_CC_PLL0 84
+#define CAM_CC_PLL0_OUT_EVEN 85
+#define CAM_CC_PLL0_OUT_ODD 86
+#define CAM_CC_PLL1 87
+#define CAM_CC_PLL1_OUT_EVEN 88
+#define CAM_CC_PLL2 89
+#define CAM_CC_PLL2_OUT_EVEN 90
+#define CAM_CC_PLL3 91
+#define CAM_CC_PLL3_OUT_EVEN 92
+#define CAM_CC_PLL4 93
+#define CAM_CC_PLL4_OUT_EVEN 94
+#define CAM_CC_PLL5 95
+#define CAM_CC_PLL5_OUT_EVEN 96
+#define CAM_CC_PLL6 97
+#define CAM_CC_PLL6_OUT_EVEN 98
+#define CAM_CC_PLL6_OUT_ODD 99
+#define CAM_CC_QDSS_DEBUG_CLK 100
+#define CAM_CC_QDSS_DEBUG_CLK_SRC 101
+#define CAM_CC_QDSS_DEBUG_XO_CLK 102
+#define CAM_CC_SLEEP_CLK 103
+#define CAM_CC_SLEEP_CLK_SRC 104
+#define CAM_CC_SLOW_AHB_CLK_SRC 105
+#define CAM_CC_TFE_0_BAYER_CLK 106
+#define CAM_CC_TFE_0_BAYER_FAST_AHB_CLK 107
+#define CAM_CC_TFE_0_CLK_SRC 108
+#define CAM_CC_TFE_0_MAIN_CLK 109
+#define CAM_CC_TFE_0_MAIN_FAST_AHB_CLK 110
+#define CAM_CC_TFE_1_BAYER_CLK 111
+#define CAM_CC_TFE_1_BAYER_FAST_AHB_CLK 112
+#define CAM_CC_TFE_1_CLK_SRC 113
+#define CAM_CC_TFE_1_MAIN_CLK 114
+#define CAM_CC_TFE_1_MAIN_FAST_AHB_CLK 115
+#define CAM_CC_TFE_2_BAYER_CLK 116
+#define CAM_CC_TFE_2_BAYER_FAST_AHB_CLK 117
+#define CAM_CC_TFE_2_CLK_SRC 118
+#define CAM_CC_TFE_2_MAIN_CLK 119
+#define CAM_CC_TFE_2_MAIN_FAST_AHB_CLK 120
+#define CAM_CC_XO_CLK_SRC 121
+
+/* CAM_CC power domains */
+#define CAM_CC_IPE_0_GDSC 0
+#define CAM_CC_OFE_GDSC 1
+#define CAM_CC_TFE_0_GDSC 2
+#define CAM_CC_TFE_1_GDSC 3
+#define CAM_CC_TFE_2_GDSC 4
+#define CAM_CC_TITAN_TOP_GDSC 5
+
+/* CAM_CC resets */
+#define CAM_CC_DRV_BCR 0
+#define CAM_CC_ICP_BCR 1
+#define CAM_CC_IPE_0_BCR 2
+#define CAM_CC_OFE_BCR 3
+#define CAM_CC_QDSS_DEBUG_BCR 4
+#define CAM_CC_TFE_0_BCR 5
+#define CAM_CC_TFE_1_BCR 6
+#define CAM_CC_TFE_2_BCR 7
+
+#endif
--
2.34.1
^ permalink raw reply related
* [PATCH v8 05/10] dt-bindings: clock: qcom: document the Eliza GPU Clock Controller
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das,
Krzysztof Kozlowski
In-Reply-To: <20260717-b4-eliza_mm_cc_v6-v8-0-5cca1bef2e48@oss.qualcomm.com>
Add bindings documentation for the Eliza Graphics Clock Controller.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
.../bindings/clock/qcom,sm8450-gpucc.yaml | 3 ++
include/dt-bindings/clock/qcom,eliza-gpucc.h | 51 ++++++++++++++++++++++
2 files changed, 54 insertions(+)
diff --git a/Documentation/devicetree/bindings/clock/qcom,sm8450-gpucc.yaml b/Documentation/devicetree/bindings/clock/qcom,sm8450-gpucc.yaml
index fdbdf605ee695637512ce4f98c9b6fcfacb9154f..734bab762a30800bda94c726f48013679f9ec542 100644
--- a/Documentation/devicetree/bindings/clock/qcom,sm8450-gpucc.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,sm8450-gpucc.yaml
@@ -15,6 +15,7 @@ description: |
domains on Qualcomm SoCs.
See also:
+ include/dt-bindings/clock/qcom,eliza-gpucc.h
include/dt-bindings/clock/qcom,glymur-gpucc.h
include/dt-bindings/clock/qcom,kaanapali-gpucc.h
include/dt-bindings/clock/qcom,milos-gpucc.h
@@ -30,6 +31,7 @@ description: |
properties:
compatible:
enum:
+ - qcom,eliza-gpucc
- qcom,glymur-gpucc
- qcom,kaanapali-gpucc
- qcom,milos-gpucc
@@ -71,6 +73,7 @@ allOf:
compatible:
contains:
enum:
+ - qcom,eliza-gpucc
- qcom,sm8750-gpucc
then:
required:
diff --git a/include/dt-bindings/clock/qcom,eliza-gpucc.h b/include/dt-bindings/clock/qcom,eliza-gpucc.h
new file mode 100644
index 0000000000000000000000000000000000000000..c3d9b7827325c5b8db696d1d95b4876e17c01c83
--- /dev/null
+++ b/include/dt-bindings/clock/qcom,eliza-gpucc.h
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#ifndef _DT_BINDINGS_CLK_QCOM_GPU_CC_ELIZA_H
+#define _DT_BINDINGS_CLK_QCOM_GPU_CC_ELIZA_H
+
+/* GPU_CC clocks */
+#define GPU_CC_AHB_CLK 0
+#define GPU_CC_CRC_AHB_CLK 1
+#define GPU_CC_CX_ACCU_SHIFT_CLK 2
+#define GPU_CC_CX_FF_CLK 3
+#define GPU_CC_CX_GMU_CLK 4
+#define GPU_CC_CXO_AON_CLK 5
+#define GPU_CC_CXO_CLK 6
+#define GPU_CC_DEMET_CLK 7
+#define GPU_CC_DEMET_DIV_CLK_SRC 8
+#define GPU_CC_FF_CLK_SRC 9
+#define GPU_CC_FREQ_MEASURE_CLK 10
+#define GPU_CC_GMU_CLK_SRC 11
+#define GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK 12
+#define GPU_CC_HUB_AON_CLK 13
+#define GPU_CC_HUB_CLK_SRC 14
+#define GPU_CC_HUB_CX_INT_CLK 15
+#define GPU_CC_MEMNOC_GFX_CLK 16
+#define GPU_CC_MND1X_0_GFX3D_CLK 17
+#define GPU_CC_MND1X_1_GFX3D_CLK 18
+#define GPU_CC_PLL0 19
+#define GPU_CC_PLL1 20
+#define GPU_CC_SLEEP_CLK 21
+#define GPU_CC_XO_CLK_SRC 22
+#define GPU_CC_XO_DIV_CLK_SRC 23
+
+/* GPU_CC power domains */
+#define GPU_CC_CX_GDSC 0
+#define GPU_CC_GX_GDSC 1
+
+/* GPU_CC resets */
+#define GPU_CC_ACD_BCR 0
+#define GPU_CC_CB_BCR 1
+#define GPU_CC_CX_BCR 2
+#define GPU_CC_FAST_HUB_BCR 3
+#define GPU_CC_FF_BCR 4
+#define GPU_CC_GFX3D_AON_BCR 5
+#define GPU_CC_GMU_BCR 6
+#define GPU_CC_GX_BCR 7
+#define GPU_CC_RBCPR_BCR 8
+#define GPU_CC_XO_BCR 9
+
+#endif
--
2.34.1
^ permalink raw reply related
* [PATCH v8 04/10] dt-bindings: clock: qcom: Add video clock controller on Qualcomm Eliza SoC
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das,
Krzysztof Kozlowski
In-Reply-To: <20260717-b4-eliza_mm_cc_v6-v8-0-5cca1bef2e48@oss.qualcomm.com>
Eliza Video clock controller is on CX and MX rails similar to Milos.
Add compatible string for Eliza video clock controller to the existing
Milos videocc binding and add the dt-bindings header for Eliza.
The video clock controller exposes power domains, so '#power-domain-cells'
must be present in the device node. Add it to the required properties list
to enforce this in binding validation.
There is no ABI breakage and no impact to the existing devices, since the
nodes using this binding already specify the '#power-domain-cells' property
for videocc.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
.../bindings/clock/qcom,milos-videocc.yaml | 10 ++++--
include/dt-bindings/clock/qcom,eliza-videocc.h | 37 ++++++++++++++++++++++
2 files changed, 45 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/qcom,milos-videocc.yaml b/Documentation/devicetree/bindings/clock/qcom,milos-videocc.yaml
index 4d8d109cd304ef0f5afc5c3fc7961a6156003d4b..08898f1d74e4ef0a3921eb7cc5f13d14bd02975b 100644
--- a/Documentation/devicetree/bindings/clock/qcom,milos-videocc.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,milos-videocc.yaml
@@ -8,16 +8,21 @@ title: Qualcomm Video Clock & Reset Controller on Milos
maintainers:
- Luca Weiss <luca.weiss@fairphone.com>
+ - Taniya Das <taniya.das@oss.qualcomm.com>
description: |
Qualcomm video clock control module provides the clocks, resets and power
domains on Milos.
- See also: include/dt-bindings/clock/qcom,milos-videocc.h
+ See also:
+ include/dt-bindings/clock/qcom,eliza-videocc.h
+ include/dt-bindings/clock/qcom,milos-videocc.h
properties:
compatible:
- const: qcom,milos-videocc
+ enum:
+ - qcom,eliza-videocc
+ - qcom,milos-videocc
clocks:
items:
@@ -41,6 +46,7 @@ required:
- clocks
- power-domains
- required-opps
+ - '#power-domain-cells'
allOf:
- $ref: qcom,gcc.yaml#
diff --git a/include/dt-bindings/clock/qcom,eliza-videocc.h b/include/dt-bindings/clock/qcom,eliza-videocc.h
new file mode 100644
index 0000000000000000000000000000000000000000..1e922250a7fae77f5c996208d50ff372b252aa51
--- /dev/null
+++ b/include/dt-bindings/clock/qcom,eliza-videocc.h
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#ifndef _DT_BINDINGS_CLK_QCOM_VIDEO_CC_ELIZA_H
+#define _DT_BINDINGS_CLK_QCOM_VIDEO_CC_ELIZA_H
+
+/* VIDEO_CC clocks */
+#define VIDEO_CC_AHB_CLK 0
+#define VIDEO_CC_AHB_CLK_SRC 1
+#define VIDEO_CC_MVS0_CLK 2
+#define VIDEO_CC_MVS0_CLK_SRC 3
+#define VIDEO_CC_MVS0_DIV_CLK_SRC 4
+#define VIDEO_CC_MVS0_SHIFT_CLK 5
+#define VIDEO_CC_MVS0C_CLK 6
+#define VIDEO_CC_MVS0C_DIV2_DIV_CLK_SRC 7
+#define VIDEO_CC_MVS0C_SHIFT_CLK 8
+#define VIDEO_CC_PLL0 9
+#define VIDEO_CC_SLEEP_CLK 10
+#define VIDEO_CC_SLEEP_CLK_SRC 11
+#define VIDEO_CC_XO_CLK 12
+#define VIDEO_CC_XO_CLK_SRC 13
+
+/* VIDEO_CC power domains */
+#define VIDEO_CC_MVS0_GDSC 0
+#define VIDEO_CC_MVS0C_GDSC 1
+
+/* VIDEO_CC resets */
+#define VIDEO_CC_INTERFACE_BCR 0
+#define VIDEO_CC_MVS0_CLK_ARES 1
+#define VIDEO_CC_MVS0_BCR 2
+#define VIDEO_CC_MVS0C_CLK_ARES 3
+#define VIDEO_CC_MVS0C_BCR 4
+#define VIDEO_CC_XO_CLK_ARES 5
+
+#endif
--
2.34.1
^ permalink raw reply related
* [PATCH v8 03/10] arm64: dts: qcom: milos: Add power-domains for camcc and videocc
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das
In-Reply-To: <20260717-b4-eliza_mm_cc_v6-v8-0-5cca1bef2e48@oss.qualcomm.com>
The Milos camera and video clock controllers operate on the CX and MX
power rails, and require these power domains along with their
associated performance state votes to be specified for accessing the
clock controller and its GDSC. Add the 'power-domains' and
'required-opps' properties to the camcc and videocc nodes.
Fixes: d9d59d105f98 ("arm64: dts: qcom: Add initial Milos dtsi")
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/milos.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/milos.dtsi b/arch/arm64/boot/dts/qcom/milos.dtsi
index 8c92329889538f0d79f7af436898e3ee278e361c..7c42d6c89829e4bf5a2ade64018623e49623462c 100644
--- a/arch/arm64/boot/dts/qcom/milos.dtsi
+++ b/arch/arm64/boot/dts/qcom/milos.dtsi
@@ -1892,6 +1892,11 @@ videocc: clock-controller@aaf0000 {
<&sleep_clk>,
<&gcc GCC_VIDEO_AHB_CLK>;
+ power-domains = <&rpmhpd RPMHPD_CX>,
+ <&rpmhpd RPMHPD_MX>;
+ required-opps = <&rpmhpd_opp_low_svs>,
+ <&rpmhpd_opp_low_svs>;
+
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
@@ -1971,6 +1976,11 @@ camcc: clock-controller@adb0000 {
<&sleep_clk>,
<&gcc GCC_CAMERA_AHB_CLK>;
+ power-domains = <&rpmhpd RPMHPD_CX>,
+ <&rpmhpd RPMHPD_MX>;
+ required-opps = <&rpmhpd_opp_low_svs>,
+ <&rpmhpd_opp_low_svs>;
+
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
--
2.34.1
^ permalink raw reply related
* [PATCH v8 02/10] dt-bindings: clock: qcom,milos-videocc: Add missing power-domains support
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das,
Krzysztof Kozlowski
In-Reply-To: <20260717-b4-eliza_mm_cc_v6-v8-0-5cca1bef2e48@oss.qualcomm.com>
The Milos video clock controller requires the CX and MX power
domains, along with their performance state votes, to be enabled
before the clock controller can be accessed.
Document the 'power-domains' and 'required-opps' properties and add
them to the required properties list and example. Since these
properties become required for the already-documented
qcom,milos-videocc compatible, this is an ABI break for any devicetree
using this binding without specifying them.
Fixes: a4937e974186 ("dt-bindings: clock: qcom: document the Milos Video Clock Controller")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
.../devicetree/bindings/clock/qcom,milos-videocc.yaml | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/Documentation/devicetree/bindings/clock/qcom,milos-videocc.yaml b/Documentation/devicetree/bindings/clock/qcom,milos-videocc.yaml
index 14c31efe1308aadbea61eb7be7e56039a923aec5..4d8d109cd304ef0f5afc5c3fc7961a6156003d4b 100644
--- a/Documentation/devicetree/bindings/clock/qcom,milos-videocc.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,milos-videocc.yaml
@@ -26,9 +26,21 @@ properties:
- description: Sleep clock source
- description: Video AHB clock from GCC
+ power-domains:
+ items:
+ - description: CX power domain
+ - description: MX power domain
+
+ required-opps:
+ items:
+ - description: CX performance point
+ - description: MX performance point
+
required:
- compatible
- clocks
+ - power-domains
+ - required-opps
allOf:
- $ref: qcom,gcc.yaml#
@@ -38,6 +50,7 @@ unevaluatedProperties: false
examples:
- |
#include <dt-bindings/clock/qcom,milos-gcc.h>
+ #include <dt-bindings/power/qcom,rpmhpd.h>
clock-controller@aaf0000 {
compatible = "qcom,milos-videocc";
reg = <0x0aaf0000 0x10000>;
@@ -45,6 +58,12 @@ examples:
<&bi_tcxo_ao_div2>,
<&sleep_clk>,
<&gcc GCC_VIDEO_AHB_CLK>;
+
+ power-domains = <&rpmhpd RPMHPD_CX>,
+ <&rpmhpd RPMHPD_MX>;
+ required-opps = <&rpmhpd_opp_low_svs>,
+ <&rpmhpd_opp_low_svs>;
+
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
--
2.34.1
^ permalink raw reply related
* [PATCH v8 01/10] dt-bindings: clock: qcom,milos-camcc: Add missing power-domains support
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das,
Krzysztof Kozlowski
In-Reply-To: <20260717-b4-eliza_mm_cc_v6-v8-0-5cca1bef2e48@oss.qualcomm.com>
The Milos camera clock controller requires the CX and MX power
domains, along with their performance state votes, to be enabled
before the clock controller can be accessed.
Document the 'power-domains' and 'required-opps' properties and add
them to the required properties list and example. Since these
properties become required for the already-documented qcom,milos-camcc
compatible, this is an ABI break for any devicetree using this binding
without specifying them.
Fixes: dbb9d53b7197 ("dt-bindings: clock: qcom: document the Milos Camera Clock Controller")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
.../devicetree/bindings/clock/qcom,milos-camcc.yaml | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/Documentation/devicetree/bindings/clock/qcom,milos-camcc.yaml b/Documentation/devicetree/bindings/clock/qcom,milos-camcc.yaml
index f63149ecf3e1b98e60dba27093737ec84b66a899..2295e7627ec9feb6a67f3ca952e6192a31cce593 100644
--- a/Documentation/devicetree/bindings/clock/qcom,milos-camcc.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,milos-camcc.yaml
@@ -25,9 +25,21 @@ properties:
- description: Sleep clock source
- description: Camera AHB clock from GCC
+ power-domains:
+ items:
+ - description: CX power domain
+ - description: MX power domain
+
+ required-opps:
+ items:
+ - description: CX performance point
+ - description: MX performance point
+
required:
- compatible
- clocks
+ - power-domains
+ - required-opps
allOf:
- $ref: qcom,gcc.yaml#
@@ -37,12 +49,19 @@ unevaluatedProperties: false
examples:
- |
#include <dt-bindings/clock/qcom,milos-gcc.h>
+ #include <dt-bindings/power/qcom,rpmhpd.h>
clock-controller@adb0000 {
compatible = "qcom,milos-camcc";
reg = <0x0adb0000 0x40000>;
clocks = <&bi_tcxo_div2>,
<&sleep_clk>,
<&gcc GCC_CAMERA_AHB_CLK>;
+
+ power-domains = <&rpmhpd RPMHPD_CX>,
+ <&rpmhpd RPMHPD_MX>;
+ required-opps = <&rpmhpd_opp_low_svs>,
+ <&rpmhpd_opp_low_svs>;
+
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
--
2.34.1
^ permalink raw reply related
* [PATCH v8 00/10] Add support for Video, Camera, Graphics clock controllers on Eliza
From: Taniya Das @ 2026-07-17 7:31 UTC (permalink / raw)
To: Bjorn Andersson, Michael Turquette, Stephen Boyd, Brian Masney,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Luca Weiss,
Konrad Dybcio, Maxime Coquelin, Alexandre Torgue,
Dmitry Baryshkov
Cc: Ajit Pandey, Imran Shaik, Jagadeesh Kona, linux-arm-msm,
linux-clk, devicetree, linux-kernel, linux-stm32,
linux-arm-kernel, Krzysztof Kozlowski, Konrad Dybcio, Taniya Das,
Krzysztof Kozlowski
Add driver for Eliza SoC camera, graphics and Video clock controllers.
The camera clock controller supports the cambist clock controller and
the regular camera clock controller.
Eliza camcc and videocc are on CX and MX rails and doesn't have MMCX
and MXC rails dependency. Add explicit power-domain voting for Milos
which are required. Hence extended the Milos camcc & videocc
documentation bindings for Eliza.
The patches have been tested on Qualcomm Eliza MTP board.
Changes in v8:
- Remove unnecessary '#include <linux/mod_devicetable.h>' from the
videocc, gpucc, camcc and cambistmclkcc Eliza drivers.
- Added the RB-by from patchset v6.
- Link to v7: https://lore.kernel.org/r/20260713-b4-eliza_mm_cc_v6-v7-0-4d91bcef50eb@oss.qualcomm.com
Changes in v7:
- Add missing 'power-domains' and 'required-opps' properties to the
Milos camcc and videocc dt-bindings, and the corresponding device
tree nodes, since the Eliza bindings extend the Milos ones. [Konrad]
- Update the camcc, videocc driver to 'use_rpm' flag for Eliza.
- Add the RB-by tags from patchset v6.
- Link to v6: https://lore.kernel.org/r/20260609-b4-eliza_mm_cc_v6-v6-0-17df09e5940c@oss.qualcomm.com
Changes in v6:
- Update device tree to latest linux-next.
- Update commit text for no ABI breakage for VideoCC and CAMCC
binding [Krzysztof]
- Added the RB-by from patchset v5.
- Link to v5: https://lore.kernel.org/r/20260525-eliza_mm_cc_v2-v5-0-a1d125619a5a@oss.qualcomm.com
Changes in v5:
- Taken care of comments from v3, v4.
- Update milos-videocc and milos-camcc bindings to add '#power-domain-cells'
as required property in bindings.
- Remove duplicate clock 'gpu_cc_gpu_smmu_vote_clk' from driver and
bindings.
- Add '#power-domain-cells' for 'camcc' and 'cambistmclkcc' device node.
- Link to v4: https://lore.kernel.org/r/20260513-eliza_mm_cc_v2-v4-0-e61b5434e8d9@oss.qualcomm.com
Changes in v4:
- Update the clock ordering for camcc and cambistmclkcc in milos.dtsi.
- Link to v3: https://lore.kernel.org/r/20260513-eliza_mm_cc_v2-v3-0-b59c370dc281@oss.qualcomm.com
Changes in v3:
- Dropped new documentation bindings & extended Milos documentation bindings for Eliza videocc & camcc.
- Dropped the defconfig patch and included the drivers as m from Kconfig itself.
- Update the header inclusion in the milos.dtsi.
- Link to v2: https://lore.kernel.org/r/20260409-eliza_mm_cc_v2-v2-0-bc0c6dd77bc5@oss.qualcomm.com
Changes in v2:
- rebased the patches on the latest linux-next.
- Add new bindings for Video and Camcc.
- Remove commented code in GPUCC (limiter code).
- Add device nodes for the corresponding clock controllers.
- Add RB-by tags for VideoCC and CamCC/Cambistmclk from v1.
- Link to v1: https://lore.kernel.org/r/20260317-eliza_mm_clock_controllers_v1-v1-0-4696eeda8cfb@oss.qualcomm.com
Signed-off-by: Taniya Das <taniya.das@oss.qualcomm.com>
---
Taniya Das (10):
dt-bindings: clock: qcom,milos-camcc: Add missing power-domains support
dt-bindings: clock: qcom,milos-videocc: Add missing power-domains support
arm64: dts: qcom: milos: Add power-domains for camcc and videocc
dt-bindings: clock: qcom: Add video clock controller on Qualcomm Eliza SoC
dt-bindings: clock: qcom: document the Eliza GPU Clock Controller
dt-bindings: clock: qcom: Add support for CAMCC for Eliza
clk: qcom: videocc: Add video clock controller driver for Eliza
clk: qcom: gpucc: Add GPU Clock Controller driver for Eliza
clk: qcom: camcc: Add support for camera clock controller for Eliza
arm64: dts: qcom: eliza: Add support for MM clock controllers
.../bindings/clock/qcom,milos-camcc.yaml | 31 +-
.../bindings/clock/qcom,milos-videocc.yaml | 29 +-
.../bindings/clock/qcom,sm8450-gpucc.yaml | 3 +
arch/arm64/boot/dts/qcom/eliza.dtsi | 76 +
arch/arm64/boot/dts/qcom/milos.dtsi | 10 +
drivers/clk/qcom/Kconfig | 31 +
drivers/clk/qcom/Makefile | 3 +
drivers/clk/qcom/cambistmclkcc-eliza.c | 464 ++++
drivers/clk/qcom/camcc-eliza.c | 2803 ++++++++++++++++++++
drivers/clk/qcom/gpucc-eliza.c | 606 +++++
drivers/clk/qcom/videocc-eliza.c | 404 +++
.../dt-bindings/clock/qcom,eliza-cambistmclkcc.h | 32 +
include/dt-bindings/clock/qcom,eliza-camcc.h | 151 ++
include/dt-bindings/clock/qcom,eliza-gpucc.h | 51 +
include/dt-bindings/clock/qcom,eliza-videocc.h | 37 +
15 files changed, 4727 insertions(+), 4 deletions(-)
---
base-commit: a87737435cfa134f9cdcc696ba3080759d04cf72
change-id: 20260609-b4-eliza_mm_cc_v6-64cc35d4a698
Best regards,
--
Taniya Das <taniya.das@oss.qualcomm.com>
^ permalink raw reply
* [PATCH v4 3/3] input: misc: Add Qualcomm SPMI PMIC haptics driver
From: Fenglin Wu @ 2026-07-17 7:29 UTC (permalink / raw)
To: linux-arm-msm, Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Lee Jones, Stephen Boyd, Bjorn Andersson,
Konrad Dybcio
Cc: David Collins, Subbaraman Narayanamurthy, Kamal Wadhwa, kernel,
linux-input, devicetree, linux-kernel, Fenglin Wu
In-Reply-To: <20260717-qcom-spmi-haptics-v4-0-b0fe0ed30849@oss.qualcomm.com>
Add an initial driver for the Qualcomm PMIH0108 PMIC haptics module,
named as HAP530_HV. This module supports several play modes, including
DIRECT_PLAY, FIFO, PAT_MEM, and SWR, each with distinct data sourcing
and hardware data handling logic. Currently, the driver provides support
for two play modes using the input force-feedback framework: FF_CONSTANT
effect for DIRECT_PLAY mode and FF_PERIODIC effect with FF_CUSTOM
waveform for FIFO mode.
Assisted-by: Claude:claude-4-8-opus
Signed-off-by: Fenglin Wu <fenglin.wu@oss.qualcomm.com>
---
drivers/input/misc/Kconfig | 11 +
drivers/input/misc/Makefile | 1 +
drivers/input/misc/qcom-spmi-haptics.c | 1178 ++++++++++++++++++++++++++++++++
3 files changed, 1190 insertions(+)
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
index 1f6c57dba030..4f40940973e4 100644
--- a/drivers/input/misc/Kconfig
+++ b/drivers/input/misc/Kconfig
@@ -236,6 +236,17 @@ config INPUT_PMIC8XXX_PWRKEY
To compile this driver as a module, choose M here: the
module will be called pmic8xxx-pwrkey.
+config INPUT_QCOM_SPMI_HAPTICS
+ tristate "Qualcomm SPMI PMIC haptics support"
+ depends on MFD_SPMI_PMIC
+ help
+ Say Y to enable support for the Qualcomm PMIH0108 SPMI PMIC haptics
+ module. Supports DIRECT_PLAY, FIFO streaming play modes via the
+ Linux input force-feedback framework.
+
+ To compile this driver as a module, choose M here: the module will
+ be called qcom-spmi-haptics.
+
config INPUT_SPARCSPKR
tristate "SPARC Speaker support"
depends on PCI && SPARC64
diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile
index 2281d6803fce..c5c9aa139a11 100644
--- a/drivers/input/misc/Makefile
+++ b/drivers/input/misc/Makefile
@@ -69,6 +69,7 @@ obj-$(CONFIG_INPUT_PMIC8XXX_PWRKEY) += pmic8xxx-pwrkey.o
obj-$(CONFIG_INPUT_POWERMATE) += powermate.o
obj-$(CONFIG_INPUT_PWM_BEEPER) += pwm-beeper.o
obj-$(CONFIG_INPUT_PWM_VIBRA) += pwm-vibra.o
+obj-$(CONFIG_INPUT_QCOM_SPMI_HAPTICS) += qcom-spmi-haptics.o
obj-$(CONFIG_INPUT_QNAP_MCU) += qnap-mcu-input.o
obj-$(CONFIG_INPUT_RAVE_SP_PWRBUTTON) += rave-sp-pwrbutton.o
obj-$(CONFIG_INPUT_RB532_BUTTON) += rb532_button.o
diff --git a/drivers/input/misc/qcom-spmi-haptics.c b/drivers/input/misc/qcom-spmi-haptics.c
new file mode 100644
index 000000000000..235f77e0229c
--- /dev/null
+++ b/drivers/input/misc/qcom-spmi-haptics.c
@@ -0,0 +1,1178 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/pm_runtime.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/uaccess.h>
+#include <linux/workqueue.h>
+
+/* HAP_CFG register offsets, bit fields, value constants */
+#define HAP_CFG_INT_RT_STS_REG 0x10
+#define FIFO_EMPTY_BIT BIT(1)
+#define HAP_CFG_EN_CTL_REG 0x46
+#define HAPTICS_EN_BIT BIT(7)
+#define HAP_CFG_VMAX_REG 0x48
+#define VMAX_STEP_MV 50
+#define VMAX_MV_MAX 10000
+#define HAP_CFG_SPMI_PLAY_REG 0x4C
+#define PLAY_EN_BIT BIT(7)
+#define PAT_SRC_MASK GENMASK(2, 0)
+#define PAT_SRC_FIFO 0
+#define PAT_SRC_DIRECT_PLAY 1
+#define HAP_CFG_TLRA_OL_HIGH_REG 0x5C
+#define TLRA_OL_MSB_MASK GENMASK(3, 0)
+#define TLRA_STEP_US 5
+#define TLRA_US_MAX 20475
+#define HAP_CFG_TLRA_OL_LOW_REG 0x5D
+#define HAP_CFG_DRV_DUTY_CFG_REG 0x60
+#define ADT_DRV_DUTY_EN_BIT BIT(7)
+#define ADT_BRK_DUTY_EN_BIT BIT(6)
+#define DRV_DUTY_MASK GENMASK(5, 3)
+#define AUTORES_DRV_DUTY_62P5 2
+#define BRK_DUTY_MASK GENMASK(2, 0)
+#define AUTORES_BRK_DUTY_62P5 5
+#define HAP_CFG_ZX_WIND_CFG_REG 0x62
+#define ZX_DEBOUNCE_MASK GENMASK(6, 4)
+#define AUTORES_ZX_DEBOUNCE 3
+#define ZX_WIN_HEIGHT_MASK GENMASK(2, 0)
+#define AUTORES_ZX_WIN_HEIGHT 2
+#define HAP_CFG_AUTORES_CFG_REG 0x63
+#define AUTORES_EN_BIT BIT(7)
+#define AUTORES_EN_DLY_MASK GENMASK(6, 2)
+#define AUTORES_EN_DLY_CYCLES 10
+#define AUTORES_ERR_WIN_MASK GENMASK(1, 0)
+#define AUTORES_ERR_WIN_25PCT 1
+#define HAP_CFG_FAULT_CLR_REG 0x66
+#define ZX_TO_FAULT_CLR_BIT BIT(4)
+#define SC_CLR_BIT BIT(2)
+#define AUTO_RES_ERR_CLR_BIT BIT(1)
+#define HPWR_RDY_FAULT_CLR_BIT BIT(0)
+#define FAULT_CLR_ALL (ZX_TO_FAULT_CLR_BIT | SC_CLR_BIT | \
+ AUTO_RES_ERR_CLR_BIT | HPWR_RDY_FAULT_CLR_BIT)
+#define HAP_CFG_RAMP_DN_CFG2_REG 0x86
+#define AUTORES_PRE_HIZ_DLY_10US 1
+
+/* HAP_PTN register offsets, bit fields, value constants */
+#define HAP_PTN_REVISION2_REG 0x01
+#define HAP_PTN_FIFO_DIN_0_REG 0x20
+#define HAP_PTN_FIFO_PLAY_RATE_REG 0x24
+#define FIFO_PLAY_RATE_MASK GENMASK(3, 0)
+#define HAP_PTN_DIRECT_PLAY_REG 0x26
+#define HAP_PTN_FIFO_EMPTY_CFG_REG 0x2A
+#define FIFO_THRESH_LSB 64
+#define HAP_PTN_FIFO_DIN_1B_REG 0x2C
+#define HAP_PTN_MEM_OP_ACCESS_REG 0x2D
+#define MEM_FLUSH_RELOAD_BIT BIT(0)
+#define HAP_PTN_MMAP_FIFO_REG 0xA0
+#define MMAP_FIFO_EXIST_BIT BIT(7)
+#define MMAP_FIFO_LEN_MASK GENMASK(6, 0)
+#define HAP_PTN_PATX_PLAY_CFG_REG 0xA2
+
+#define HAP530_MEM_TOTAL_BYTES 8192
+#define FIFO_EMPTY_THRESH 280
+#define FIFO_INIT_FILL 320
+
+#define HAPTICS_AUTOSUSPEND_MS 1000
+
+/*
+ * FF_CUSTOM data layout (custom_data[] of type s16):
+ * [0] = play rate (PLAY_RATE_*)
+ * [1] = vmax in mV (0 = use device default from qcom,vmax-microvolt)
+ * [2..N-1] = signed 8-bit PCM samples packed one per s16 (lower byte used)
+ */
+#define CUSTOM_DATA_RATE_IDX 0
+#define CUSTOM_DATA_VMAX_IDX 1
+#define CUSTOM_DATA_SAMPLE_START 2
+#define CUSTOM_DATA_MAX_LEN (48 * 1024)
+
+#define HAPTICS_MAX_EFFECTS 8
+
+enum qcom_haptics_mode {
+ HAPTICS_MODE_NONE,
+ HAPTICS_DIRECT_PLAY,
+ HAPTICS_FIFO,
+};
+
+enum qcom_haptics_play_rate {
+ PLAY_RATE_T_LRA = 0,
+ PLAY_RATE_T_LRA_DIV_2 = 1,
+ PLAY_RATE_T_LRA_DIV_4 = 2,
+ PLAY_RATE_T_LRA_DIV_8 = 3,
+ PLAY_RATE_T_LRA_X_2 = 4,
+ PLAY_RATE_T_LRA_X_4 = 5,
+ PLAY_RATE_T_LRA_X_8 = 6,
+ PLAY_RATE_RESERVED = 7,
+ PLAY_RATE_F_8KHZ = 8,
+ PLAY_RATE_F_16KHZ = 9,
+ PLAY_RATE_F_24KHZ = 10,
+ PLAY_RATE_F_32KHZ = 11,
+ PLAY_RATE_F_44P1KHZ = 12,
+ PLAY_RATE_F_48KHZ = 13,
+ PLAY_RATE_MAX = PLAY_RATE_F_48KHZ,
+};
+
+/**
+ * struct qcom_haptics_effect: A haptics effect
+ * @mode: haptics HW play mode
+ * @vmax_mv: peak voltage of the haptics output waveform
+ * @length_us: vibration play duration
+ * @amplitude: DIRECT_PLAY mode output waveform amplitude
+ * @play_rate: FIFO mode play rate
+ * @fifo_data: 8-bit data samples consumed in FIFO mode
+ * @data_len: length of the FIFO data samples
+ */
+struct qcom_haptics_effect {
+ enum qcom_haptics_mode mode;
+ u32 vmax_mv;
+ u32 length_us;
+
+ u8 amplitude;
+
+ enum qcom_haptics_play_rate play_rate;
+ s8 *fifo_data;
+ u32 data_len;
+};
+
+/**
+ * struct haptics_play_req: A haptics play request
+ * @node: list node of the request
+ * @effect_id: effect index of the request
+ * @play: flag of starting or stopping the play
+ */
+struct haptics_play_req {
+ struct list_head node;
+ int effect_id;
+ bool play;
+};
+
+/**
+ * struct qcom_haptics
+ * @dev: underlying SPMI device
+ * @regmap: regmap for SPMI register access
+ * @input: input device exposing the FF interface
+ * @cfg_base: base address of the CFG peripheral
+ * @ptn_base: base address of the PTN peripheral
+ * @t_lra_us: LRA resonance period in microseconds
+ * @vmax_mv: maximum actuator drive voltage in millivolts
+ * @fifo_len: programmed HW FIFO depth in bytes
+ * @gain: playback gain scaler
+ * @play_work: delayed work that plays the queued requests
+ * @play_lock: mutex lock to serialize playbacks
+ * @play_queue_lock: spinlock protecting @play_queue
+ * @play_queue: The list of pending start/stop requests
+ * @active_effect_id: index into @effects[] currently under play
+ * @active_mode: mode of the effect currently armed in hardware
+ * @fifo_empty_irq: IRQ number for the FIFO-empty interrupt
+ * @pm_ref_held: true while a pm_runtime_get is held
+ * @irq_enabled: true if fifo_empty_irq is enabled
+ * @fifo_lock: mutex protecting the FIFO streaming data
+ * @fifo_data: pointer of the data buffer for FIFO streaming
+ * @data_len: length of the data buffer for current effect
+ * @data_written: number of samples written to the hardware FIFO
+ * @effects: table of the effects
+ */
+struct qcom_haptics {
+ struct device *dev;
+ struct regmap *regmap;
+ struct input_dev *input;
+
+ u32 cfg_base;
+ u32 ptn_base;
+ u32 t_lra_us;
+ u32 vmax_mv;
+ u32 fifo_len;
+ atomic_t gain;
+
+ struct delayed_work play_work;
+ struct mutex play_lock; /* mutex used to serialize playbacks */
+
+ spinlock_t play_queue_lock; /* protects play_queue */
+ struct list_head play_queue;
+
+ int active_effect_id;
+ enum qcom_haptics_mode active_mode;
+
+ int fifo_empty_irq;
+ bool pm_ref_held;
+ bool irq_enabled;
+
+ struct mutex fifo_lock; /* protect the FIFO data during play */
+ const s8 *fifo_data;
+ u32 data_len;
+ u32 data_written;
+
+ struct qcom_haptics_effect effects[HAPTICS_MAX_EFFECTS];
+};
+
+static int cfg_write(struct qcom_haptics *h, u32 off, u32 val)
+{
+ return regmap_write(h->regmap, h->cfg_base + off, val);
+}
+
+static int cfg_update_bits(struct qcom_haptics *h, u32 off, u32 mask, u32 val)
+{
+ return regmap_update_bits(h->regmap, h->cfg_base + off, mask, val);
+}
+
+static int ptn_write(struct qcom_haptics *h, u32 off, u32 val)
+{
+ return regmap_write(h->regmap, h->ptn_base + off, val);
+}
+
+static int ptn_update_bits(struct qcom_haptics *h, u32 off, u32 mask, u32 val)
+{
+ return regmap_update_bits(h->regmap, h->ptn_base + off, mask, val);
+}
+
+static int ptn_bulk_write(struct qcom_haptics *h, u32 off,
+ const void *buf, size_t count)
+{
+ return regmap_bulk_write(h->regmap, h->ptn_base + off, buf, count);
+}
+
+static int haptics_clear_faults(struct qcom_haptics *h)
+{
+ return cfg_write(h, HAP_CFG_FAULT_CLR_REG, FAULT_CLR_ALL);
+}
+
+static int haptics_set_vmax(struct qcom_haptics *h, u32 vmax_mv)
+{
+ return cfg_write(h, HAP_CFG_VMAX_REG, vmax_mv / VMAX_STEP_MV);
+}
+
+static int haptics_config_lra_period(struct qcom_haptics *h)
+{
+ u32 tmp = h->t_lra_us / TLRA_STEP_US;
+ int ret;
+
+ ret = cfg_write(h, HAP_CFG_TLRA_OL_HIGH_REG, (tmp >> 8) & TLRA_OL_MSB_MASK);
+ if (ret)
+ return ret;
+
+ return cfg_write(h, HAP_CFG_TLRA_OL_LOW_REG, tmp & 0xFF);
+}
+
+static int haptics_enable_module(struct qcom_haptics *h, bool enable)
+{
+ return cfg_update_bits(h, HAP_CFG_EN_CTL_REG, HAPTICS_EN_BIT,
+ enable ? HAPTICS_EN_BIT : 0);
+}
+
+static int haptics_configure_autores(struct qcom_haptics *h)
+{
+ int ret;
+
+ /* AUTORES_CFG: enable, 10-cycle delay, 25% error window */
+ ret = cfg_write(h, HAP_CFG_AUTORES_CFG_REG,
+ AUTORES_EN_BIT |
+ FIELD_PREP(AUTORES_EN_DLY_MASK, AUTORES_EN_DLY_CYCLES) |
+ FIELD_PREP(AUTORES_ERR_WIN_MASK, AUTORES_ERR_WIN_25PCT));
+ if (ret)
+ return ret;
+
+ /* DRV_DUTY: adaptive drive/brake duty cycles at 62.5% */
+ ret = cfg_write(h, HAP_CFG_DRV_DUTY_CFG_REG,
+ ADT_DRV_DUTY_EN_BIT | ADT_BRK_DUTY_EN_BIT |
+ FIELD_PREP(DRV_DUTY_MASK, AUTORES_DRV_DUTY_62P5) |
+ FIELD_PREP(BRK_DUTY_MASK, AUTORES_BRK_DUTY_62P5));
+ if (ret)
+ return ret;
+
+ /* Pre-HIZ delay: 10 µs */
+ ret = cfg_write(h, HAP_CFG_RAMP_DN_CFG2_REG, AUTORES_PRE_HIZ_DLY_10US);
+ if (ret)
+ return ret;
+
+ /* Zero-cross window: debounce 3, no hysteresis, height 2 */
+ return cfg_write(h, HAP_CFG_ZX_WIND_CFG_REG,
+ FIELD_PREP(ZX_DEBOUNCE_MASK, AUTORES_ZX_DEBOUNCE) |
+ FIELD_PREP(ZX_WIN_HEIGHT_MASK, AUTORES_ZX_WIN_HEIGHT));
+}
+
+static int haptics_write_fifo_chunk(struct qcom_haptics *h,
+ const s8 *data, u32 len)
+{
+ u32 bulk_len = ALIGN_DOWN(len, 4);
+ int i, ret;
+
+ /*
+ * FIFO data writing supports both 4-byte bulk writes using registers
+ * [HAP_PTN_FIFO_DIN_0_REG ... HAP_PTN_FIFO_DIN_3_REG], and 1-byte writes
+ * using the HAP_PTN_FIFO_DIN_1B_REG register. The 4-byte bulk write is more
+ * efficient, so use 4-byte writes for the initial 4-byte aligned data,
+ * and 1-byte writes for any trailing remainder.
+ */
+ for (i = 0; i < bulk_len; i += 4) {
+ ret = ptn_bulk_write(h, HAP_PTN_FIFO_DIN_0_REG, &data[i], 4);
+ if (ret)
+ return ret;
+ }
+
+ for (; i < len; i++) {
+ ret = ptn_write(h, HAP_PTN_FIFO_DIN_1B_REG, (u8)data[i]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int haptics_configure_fifo_mmap(struct qcom_haptics *h)
+{
+ u32 fifo_len, fifo_units;
+
+ /* Config all memory space for FIFO usage for now */
+ fifo_len = HAP530_MEM_TOTAL_BYTES;
+ fifo_len = ALIGN_DOWN(fifo_len, 64);
+ fifo_units = fifo_len / 64;
+ h->fifo_len = fifo_len;
+
+ return ptn_write(h, HAP_PTN_MMAP_FIFO_REG,
+ MMAP_FIFO_EXIST_BIT |
+ FIELD_PREP(MMAP_FIFO_LEN_MASK, fifo_units - 1));
+}
+
+static u32 haptics_gain_scaled_vmax(struct qcom_haptics *h, u32 vmax_mv)
+{
+ u16 gain = atomic_read(&h->gain);
+ u32 v = mult_frac(vmax_mv, gain, 0xFFFF);
+
+ return max_t(u32, v, VMAX_STEP_MV);
+}
+
+static void haptics_fifo_irq_enable(struct qcom_haptics *h, bool enable)
+{
+ if (h->irq_enabled == enable)
+ return;
+
+ if (enable)
+ enable_irq(h->fifo_empty_irq);
+ else
+ disable_irq(h->fifo_empty_irq);
+
+ h->irq_enabled = enable;
+}
+
+static int haptics_enqueue_play_req(struct qcom_haptics *h, int effect_id, bool play)
+{
+ struct haptics_play_req *req;
+
+ guard(spinlock_irqsave)(&h->play_queue_lock);
+
+ /*
+ * Coalesce with an already queued request for
+ * the same effect instead of appending.
+ */
+ list_for_each_entry(req, &h->play_queue, node) {
+ if (req->effect_id == effect_id) {
+ req->play = play;
+ return 0;
+ }
+ }
+
+ req = kmalloc_obj(*req, GFP_ATOMIC);
+ if (!req)
+ return -ENOMEM;
+
+ req->effect_id = effect_id;
+ req->play = play;
+
+ list_add_tail(&req->node, &h->play_queue);
+
+ return 0;
+}
+
+static struct haptics_play_req *haptics_dequeue_play_req(struct qcom_haptics *h)
+{
+ struct haptics_play_req *req = NULL;
+
+ guard(spinlock_irqsave)(&h->play_queue_lock);
+
+ if (!list_empty(&h->play_queue)) {
+ req = list_first_entry(&h->play_queue, struct haptics_play_req, node);
+ list_del(&req->node);
+ }
+
+ return req;
+}
+
+static bool haptics_queue_pending(struct qcom_haptics *h)
+{
+ guard(spinlock_irqsave)(&h->play_queue_lock);
+
+ return !list_empty(&h->play_queue);
+}
+
+static void haptics_queue_remove_effect(struct qcom_haptics *h, int effect_id)
+{
+ struct haptics_play_req *req, *tmp;
+
+ guard(spinlock_irqsave)(&h->play_queue_lock);
+
+ list_for_each_entry_safe(req, tmp, &h->play_queue, node) {
+ if (req->effect_id == effect_id) {
+ list_del(&req->node);
+ kfree(req);
+ }
+ }
+}
+
+static void haptics_queue_flush(struct qcom_haptics *h)
+{
+ struct haptics_play_req *req, *tmp;
+
+ guard(spinlock_irqsave)(&h->play_queue_lock);
+
+ list_for_each_entry_safe(req, tmp, &h->play_queue, node) {
+ list_del(&req->node);
+ kfree(req);
+ }
+}
+
+static int haptics_start_direct_play(struct qcom_haptics *h, int effect_id)
+{
+ struct qcom_haptics_effect *eff = &h->effects[effect_id];
+ int ret;
+
+ ret = haptics_clear_faults(h);
+ if (ret)
+ return ret;
+
+ /* Enable auto-resonance for DIRECT_PLAY mode */
+ ret = cfg_update_bits(h, HAP_CFG_AUTORES_CFG_REG,
+ AUTORES_EN_BIT, AUTORES_EN_BIT);
+ if (ret)
+ return ret;
+
+ ret = haptics_set_vmax(h, haptics_gain_scaled_vmax(h, h->vmax_mv));
+ if (ret)
+ return ret;
+
+ ret = ptn_write(h, HAP_PTN_DIRECT_PLAY_REG, eff->amplitude);
+ if (ret)
+ return ret;
+
+ return cfg_write(h, HAP_CFG_SPMI_PLAY_REG,
+ PLAY_EN_BIT | FIELD_PREP(PAT_SRC_MASK, PAT_SRC_DIRECT_PLAY));
+}
+
+static int haptics_start_fifo(struct qcom_haptics *h, int effect_id)
+{
+ struct qcom_haptics_effect *eff = &h->effects[effect_id];
+ u32 vmax = eff->vmax_mv ? eff->vmax_mv : h->vmax_mv;
+ u32 init_len;
+ bool data_done;
+ int ret;
+
+ if (!eff->fifo_data || !eff->data_len)
+ return -EINVAL;
+
+ ret = haptics_clear_faults(h);
+ if (ret)
+ return ret;
+
+ /* Disable auto-resonance for FIFO mode */
+ ret = cfg_update_bits(h, HAP_CFG_AUTORES_CFG_REG, AUTORES_EN_BIT, 0);
+ if (ret)
+ return ret;
+
+ ret = haptics_set_vmax(h, haptics_gain_scaled_vmax(h, vmax));
+ if (ret)
+ return ret;
+
+ ret = ptn_update_bits(h, HAP_PTN_FIFO_PLAY_RATE_REG,
+ FIFO_PLAY_RATE_MASK,
+ FIELD_PREP(FIFO_PLAY_RATE_MASK, eff->play_rate));
+ if (ret)
+ return ret;
+
+ /* Flush FIFO before loading new data */
+ ret = ptn_write(h, HAP_PTN_MEM_OP_ACCESS_REG, MEM_FLUSH_RELOAD_BIT);
+ if (ret)
+ return ret;
+ ret = ptn_write(h, HAP_PTN_MEM_OP_ACCESS_REG, 0);
+ if (ret)
+ return ret;
+
+ guard(mutex)(&h->fifo_lock);
+
+ /* Write the initial chunk and initialise streaming state */
+ init_len = min_t(u32, eff->data_len, FIFO_INIT_FILL);
+ ret = haptics_write_fifo_chunk(h, eff->fifo_data, init_len);
+ if (ret)
+ return ret;
+
+ h->fifo_data = eff->fifo_data;
+ h->data_len = eff->data_len;
+ h->data_written = init_len;
+
+ /*
+ * Set empty threshold. When threshold > 0 the hardware fires the
+ * FIFO-empty interrupt when occupancy drops below the threshold,
+ * allowing the driver to refill.
+ */
+ data_done = (h->data_written >= h->data_len);
+ if (!data_done) {
+ ret = ptn_write(h, HAP_PTN_FIFO_EMPTY_CFG_REG,
+ FIFO_EMPTY_THRESH / FIFO_THRESH_LSB);
+ if (ret) {
+ dev_err(h->dev, "set FIFO empty threshold failed, ret=%d\n", ret);
+ h->fifo_data = NULL;
+ return ret;
+ }
+
+ haptics_fifo_irq_enable(h, true);
+ }
+
+ ret = cfg_write(h, HAP_CFG_SPMI_PLAY_REG,
+ PLAY_EN_BIT | FIELD_PREP(PAT_SRC_MASK, PAT_SRC_FIFO));
+ if (ret) {
+ dev_err(h->dev, "trigger FIFO play failed, ret=%d\n", ret);
+ ptn_write(h, HAP_PTN_FIFO_EMPTY_CFG_REG, 0);
+ /*
+ * HW play never started since this SPMI write itself failed,
+ * and the FIFO empty IRQ has never fired, so disabling the
+ * IRQ synchronously here can't deadlock against 'fifo_lock'.
+ */
+ haptics_fifo_irq_enable(h, false);
+ h->fifo_data = NULL;
+ return ret;
+ }
+
+ return 0;
+}
+
+/*
+ * haptics_fifo_empty_irq: Threaded IRQ handler for the FIFO-empty interrupt.
+ *
+ * While a FIFO play is in progress the hardware fires this interrupt when
+ * the number of samples in the FIFO drops below the programmed threshold.
+ * The handler refills the FIFO from the effect's data buffer. When all
+ * samples have been written the threshold is set to zero. The HW would
+ * stop the play automatically after all of the samples in FIFO memory are
+ * played out.
+ */
+static irqreturn_t haptics_fifo_empty_irq(int irq, void *dev_id)
+{
+ struct qcom_haptics *h = dev_id;
+ u32 sts, to_write;
+ int ret;
+
+ ret = regmap_read(h->regmap,
+ h->cfg_base + HAP_CFG_INT_RT_STS_REG, &sts);
+ if (ret || !(sts & FIFO_EMPTY_BIT))
+ return IRQ_HANDLED;
+
+ guard(mutex)(&h->fifo_lock);
+
+ if (!h->fifo_data)
+ return IRQ_HANDLED;
+
+ /* Refill: write the next chunk */
+ to_write = min_t(u32, h->data_len - h->data_written,
+ h->fifo_len - FIFO_EMPTY_THRESH);
+ ret = haptics_write_fifo_chunk(h, &h->fifo_data[h->data_written], to_write);
+ if (ret) {
+ dev_err(h->dev, "refill FIFO samples failed, ret=%d\n", ret);
+ /*
+ * If data refilling is failed,stop the HW play and disable the
+ * IRQ to prevent the FIFO empty IRQ being fired continuously.
+ */
+ cfg_write(h, HAP_CFG_SPMI_PLAY_REG, 0);
+ disable_irq_nosync(h->fifo_empty_irq);
+ h->irq_enabled = false;
+ return IRQ_HANDLED;
+ }
+
+ h->data_written += to_write;
+
+ /* Disable the interrupt after all the data is queued */
+ if (h->data_written >= h->data_len)
+ ptn_write(h, HAP_PTN_FIFO_EMPTY_CFG_REG, 0);
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * haptics_stop_locked: stop play in HW and put runtime PM
+ * @h: haptics device
+ * @put_noidle: a flag to put noidle
+ *
+ * Stop HW play, clear the FIFO data if the active effect was FIFO-mode, and
+ * put runtime PM into either noidle or autosuspend based on put_noidle flag.
+ *
+ * Must be called with play_lock held.
+ */
+static void haptics_stop_locked(struct qcom_haptics *h, bool put_noidle)
+{
+ cfg_write(h, HAP_CFG_SPMI_PLAY_REG, 0);
+
+ if (h->active_mode == HAPTICS_FIFO) {
+ ptn_write(h, HAP_PTN_FIFO_EMPTY_CFG_REG, 0);
+ haptics_fifo_irq_enable(h, false);
+ scoped_guard(mutex, &h->fifo_lock) {
+ h->fifo_data = NULL;
+ }
+ }
+
+ h->active_effect_id = -1;
+ h->active_mode = HAPTICS_MODE_NONE;
+
+ if (h->pm_ref_held) {
+ if (put_noidle)
+ pm_runtime_put_noidle(h->dev);
+ else
+ pm_runtime_put_autosuspend(h->dev);
+
+ h->pm_ref_held = false;
+ }
+}
+
+/*
+ * haptics_start_locked: start to play an effect
+ * @h: haptics device
+ * @effect_id: the index of the effect
+ *
+ * If an effect is currently active, stop it 1st. Acquires a PM ref
+ * if not already held, and then trigger the play based on the
+ * play mode. Update active_effect_id/active_mode on success.
+ *
+ * Must be called with play_lock held.
+ */
+static int haptics_start_locked(struct qcom_haptics *h, int effect_id)
+{
+ int ret;
+
+ if (h->active_effect_id != -1)
+ haptics_stop_locked(h, false);
+
+ if (!h->pm_ref_held) {
+ ret = pm_runtime_resume_and_get(h->dev);
+ if (ret < 0) {
+ dev_err(h->dev, "failed to resume device: %d\n", ret);
+ return ret;
+ }
+
+ h->pm_ref_held = true;
+ }
+
+ switch (h->effects[effect_id].mode) {
+ case HAPTICS_DIRECT_PLAY:
+ ret = haptics_start_direct_play(h, effect_id);
+ break;
+ case HAPTICS_FIFO:
+ ret = haptics_start_fifo(h, effect_id);
+ break;
+ default:
+ ret = -EINVAL;
+ }
+
+ if (ret) {
+ dev_err(h->dev, "failed to start effect %d: %d\n", effect_id, ret);
+ if (h->pm_ref_held) {
+ pm_runtime_put_autosuspend(h->dev);
+ h->pm_ref_held = false;
+ }
+
+ return ret;
+ }
+
+ h->active_effect_id = effect_id;
+ h->active_mode = h->effects[effect_id].mode;
+
+ return 0;
+}
+
+static void haptics_play_work(struct work_struct *work)
+{
+ struct qcom_haptics *h = container_of(to_delayed_work(work),
+ struct qcom_haptics, play_work);
+ struct haptics_play_req *req = haptics_dequeue_play_req(h);
+ bool rearmed = false;
+ u32 length_us;
+ int ret;
+
+ guard(mutex)(&h->play_lock);
+
+ /* No valid request available */
+ if (req == NULL)
+ return;
+
+ if (req->play) {
+ ret = haptics_start_locked(h, req->effect_id);
+ if (ret) {
+ dev_err(h->dev, "play haptics failed, ret=%d\n", ret);
+ } else {
+ /*
+ * Re-arm the work to stop the play or advance
+ * to next play after the play duration
+ */
+ length_us = h->effects[req->effect_id].length_us;
+ if (length_us) {
+ schedule_delayed_work(&h->play_work,
+ usecs_to_jiffies(length_us));
+ rearmed = true;
+ }
+ }
+ } else {
+ if (req->effect_id != h->active_effect_id)
+ dev_warn(h->dev, "effect %d is not under playing\n", req->effect_id);
+ else
+ haptics_stop_locked(h, false);
+ }
+
+ kfree(req);
+
+ /*
+ * Handle the remaining requests if doesn't need to wait
+ */
+ if (!rearmed && haptics_queue_pending(h))
+ schedule_delayed_work(&h->play_work, 0);
+}
+
+static void haptics_clear_effect(struct qcom_haptics *h,
+ struct qcom_haptics_effect *effect)
+{
+ guard(mutex)(&h->fifo_lock);
+
+ if (h->fifo_data == effect->fifo_data)
+ h->fifo_data = NULL;
+
+ kvfree(effect->fifo_data);
+ effect->fifo_data = NULL;
+ effect->data_len = 0;
+}
+
+/*
+ * haptics_fifo_length_us: Calculate the play duration of a FIFO effect.
+ * @h: haptics device pointer
+ * @rate: FIFO data play rate
+ * @data_len: FFO data length
+ *
+ * Each FIFO sample is played out over one play-rate period, so the total
+ * duration is the number of samples times that period:
+ *
+ * length_us = (clk_base * data_len * multiplier) / divider
+ *
+ * For T_LRA-based rates the period derives from the LRA resonance period
+ * (h->t_lra_us): DIV_2/4/8 shorten it, X_2/4/8 lengthen it. For the
+ * kHz-based rates the period is 1000 us / freq_khz.
+ */
+static u32 haptics_fifo_length_us(struct qcom_haptics *h,
+ enum qcom_haptics_play_rate rate,
+ u32 data_len)
+{
+ u32 clk_base = 1000, multiplier = 1, divider = 1;
+
+ switch (rate) {
+ case PLAY_RATE_T_LRA:
+ clk_base = h->t_lra_us;
+ break;
+ case PLAY_RATE_T_LRA_DIV_2:
+ clk_base = h->t_lra_us;
+ divider = 2;
+ break;
+ case PLAY_RATE_T_LRA_DIV_4:
+ clk_base = h->t_lra_us;
+ divider = 4;
+ break;
+ case PLAY_RATE_T_LRA_DIV_8:
+ clk_base = h->t_lra_us;
+ divider = 8;
+ break;
+ case PLAY_RATE_T_LRA_X_2:
+ clk_base = h->t_lra_us;
+ multiplier = 2;
+ break;
+ case PLAY_RATE_T_LRA_X_4:
+ clk_base = h->t_lra_us;
+ multiplier = 4;
+ break;
+ case PLAY_RATE_T_LRA_X_8:
+ clk_base = h->t_lra_us;
+ multiplier = 8;
+ break;
+ case PLAY_RATE_F_8KHZ:
+ divider = 8;
+ break;
+ case PLAY_RATE_F_16KHZ:
+ divider = 16;
+ break;
+ case PLAY_RATE_F_24KHZ:
+ divider = 24;
+ break;
+ case PLAY_RATE_F_32KHZ:
+ divider = 32;
+ break;
+ case PLAY_RATE_F_44P1KHZ:
+ clk_base *= 10;
+ divider = 441;
+ break;
+ case PLAY_RATE_F_48KHZ:
+ divider = 48;
+ break;
+ default:
+ /* Unexpected rate: fall back to the resonance period. */
+ clk_base = h->t_lra_us;
+ break;
+ }
+
+ return div_u64((u64)clk_base * data_len * multiplier, divider);
+}
+
+static int haptics_upload_effect(struct input_dev *dev,
+ struct ff_effect *effect,
+ struct ff_effect *old)
+{
+ struct qcom_haptics *h = input_get_drvdata(dev);
+ struct qcom_haptics_effect *priv;
+ int id = effect->id;
+ u32 data_len, level;
+ s8 *fifo;
+
+ s16 *buf __free(kvfree) = NULL;
+
+ guard(mutex)(&h->play_lock);
+
+ if (id < 0 || id >= HAPTICS_MAX_EFFECTS)
+ return -EINVAL;
+
+ if (id == h->active_effect_id) {
+ dev_err(h->dev, "effect %d is under playing\n", id);
+ return -EBUSY;
+ }
+
+ priv = &h->effects[id];
+
+ switch (effect->type) {
+ case FF_CONSTANT:
+ haptics_clear_effect(h, priv);
+ level = effect->u.constant.level <= 0 ? 0 : effect->u.constant.level;
+ priv->amplitude = (u8)mult_frac(level, 255, 0x7FFF);
+ priv->length_us = effect->replay.length * USEC_PER_MSEC;
+ priv->mode = HAPTICS_DIRECT_PLAY;
+ return 0;
+
+ case FF_PERIODIC:
+ if (effect->u.periodic.waveform != FF_CUSTOM)
+ return -EINVAL;
+ /*
+ * Minimum 3 elements: play-rate code + vmax + at least one sample.
+ * Limit the maximum data length to ~48K so that it can at least
+ * handle ~1s vibration at the fast (48K) play rate.
+ */
+ if (effect->u.periodic.custom_len < 3 ||
+ effect->u.periodic.custom_len > CUSTOM_DATA_MAX_LEN + 2)
+ return -EINVAL;
+
+ buf = vmemdup_array_user(effect->u.periodic.custom_data,
+ effect->u.periodic.custom_len,
+ sizeof(s16));
+ if (IS_ERR(buf))
+ return PTR_ERR(no_free_ptr(buf));
+
+ if (buf[CUSTOM_DATA_RATE_IDX] < 0 ||
+ buf[CUSTOM_DATA_RATE_IDX] > PLAY_RATE_MAX ||
+ buf[CUSTOM_DATA_RATE_IDX] == PLAY_RATE_RESERVED)
+ return -EINVAL;
+
+ data_len = effect->u.periodic.custom_len - CUSTOM_DATA_SAMPLE_START;
+
+ fifo = kvmalloc(data_len, GFP_KERNEL);
+ if (!fifo)
+ return -ENOMEM;
+
+ /* Pack: one s8 sample per s16 slot (lower byte) */
+ for (int i = 0; i < data_len; i++)
+ fifo[i] = (s8)buf[CUSTOM_DATA_SAMPLE_START + i];
+
+ haptics_clear_effect(h, priv);
+
+ scoped_guard(mutex, &h->fifo_lock) {
+ priv->fifo_data = fifo;
+ priv->data_len = data_len;
+ }
+
+ priv->play_rate = (u8)buf[CUSTOM_DATA_RATE_IDX];
+ priv->vmax_mv = (u32)clamp_val(buf[CUSTOM_DATA_VMAX_IDX], 0, VMAX_MV_MAX);
+ priv->length_us = haptics_fifo_length_us(h, priv->play_rate, data_len);
+ priv->mode = HAPTICS_FIFO;
+
+ return 0;
+
+ default:
+ return -EINVAL;
+ }
+}
+
+static int haptics_playback(struct input_dev *dev, int effect_id, int val)
+{
+ struct qcom_haptics *h = input_get_drvdata(dev);
+ int ret;
+
+ ret = haptics_enqueue_play_req(h, effect_id, val > 0);
+ if (ret)
+ return ret;
+
+ if (val > 0)
+ /*
+ * Queue the play. If a duration re-arm is already pending this
+ * is a no-op, so the new play waits for the current effect to
+ * finish before the worker dequeues it.
+ */
+ schedule_delayed_work(&h->play_work, 0);
+ else
+ /*
+ * Run the worker now, cancelling any pending duration re-arm,
+ * so an explicit stop takes effect immediately.
+ */
+ mod_delayed_work(system_percpu_wq, &h->play_work, 0);
+
+ return 0;
+}
+
+static int haptics_erase(struct input_dev *dev, int effect_id)
+{
+ struct qcom_haptics *h = input_get_drvdata(dev);
+ struct qcom_haptics_effect *priv = &h->effects[effect_id];
+
+ guard(mutex)(&h->play_lock);
+
+ haptics_queue_remove_effect(h, effect_id);
+
+ if (h->active_effect_id == effect_id)
+ haptics_stop_locked(h, false);
+
+ haptics_clear_effect(h, priv);
+ priv->mode = HAPTICS_MODE_NONE;
+
+ return 0;
+}
+
+static void haptics_set_gain(struct input_dev *dev, u16 gain)
+{
+ struct qcom_haptics *h = input_get_drvdata(dev);
+
+ atomic_set(&h->gain, gain);
+}
+
+static int qcom_haptics_probe(struct platform_device *pdev)
+{
+ struct qcom_haptics *h;
+ struct input_dev *input;
+ struct ff_device *ff;
+ u32 regs[2], vmax_uv;
+ int ret, irq;
+
+ h = devm_kzalloc(&pdev->dev, sizeof(*h), GFP_KERNEL);
+ if (!h)
+ return -ENOMEM;
+
+ h->dev = &pdev->dev;
+
+ h->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!h->regmap)
+ return dev_err_probe(h->dev, -ENODEV, "no regmap from parent\n");
+
+ ret = device_property_read_u32_array(h->dev, "reg", regs, ARRAY_SIZE(regs));
+ if (ret)
+ return dev_err_probe(h->dev, ret, "failed to read 'reg' property\n");
+
+ h->cfg_base = regs[0];
+ h->ptn_base = regs[1];
+
+ ret = device_property_read_u32(h->dev, "qcom,lra-period-us", &h->t_lra_us);
+ if (ret)
+ return dev_err_probe(h->dev, ret, "missing qcom,lra-period-us\n");
+
+ h->t_lra_us = clamp(h->t_lra_us, (u32)TLRA_STEP_US, (u32)TLRA_US_MAX);
+
+ ret = device_property_read_u32(h->dev, "qcom,vmax-microvolt", &vmax_uv);
+ if (ret)
+ return dev_err_probe(h->dev, ret, "missing qcom,vmax-microvolt\n");
+
+ h->vmax_mv = clamp(vmax_uv / 1000, (u32)VMAX_STEP_MV, (u32)VMAX_MV_MAX);
+
+ ret = haptics_config_lra_period(h);
+ if (ret)
+ return ret;
+
+ ret = haptics_configure_autores(h);
+ if (ret)
+ return ret;
+
+ ret = haptics_set_vmax(h, h->vmax_mv);
+ if (ret)
+ return ret;
+
+ ret = haptics_configure_fifo_mmap(h);
+ if (ret)
+ return ret;
+
+ mutex_init(&h->play_lock);
+ mutex_init(&h->fifo_lock);
+ spin_lock_init(&h->play_queue_lock);
+ INIT_LIST_HEAD(&h->play_queue);
+ INIT_DELAYED_WORK(&h->play_work, haptics_play_work);
+ atomic_set(&h->gain, 0xFFFF);
+ h->active_effect_id = -1;
+
+ irq = platform_get_irq_byname(pdev, "fifo-empty");
+ if (irq < 0)
+ return dev_err_probe(h->dev, irq, "failed to get fifo-empty IRQ\n");
+
+ ret = devm_request_threaded_irq(h->dev, irq, NULL,
+ haptics_fifo_empty_irq,
+ IRQF_ONESHOT | IRQF_NO_AUTOEN,
+ "qcom-haptics-fifo-empty", h);
+ if (ret)
+ return dev_err_probe(h->dev, ret, "failed to request fifo-empty IRQ\n");
+
+ h->fifo_empty_irq = irq;
+ platform_set_drvdata(pdev, h);
+
+ pm_runtime_use_autosuspend(h->dev);
+ pm_runtime_set_autosuspend_delay(h->dev, HAPTICS_AUTOSUSPEND_MS);
+ ret = devm_pm_runtime_enable(h->dev);
+ if (ret)
+ return dev_err_probe(h->dev, ret, "enable runtime PM failed\n");
+
+ input = devm_input_allocate_device(h->dev);
+ if (!input)
+ return -ENOMEM;
+
+ input->name = "qcom-spmi-haptics";
+ input_set_drvdata(input, h);
+ h->input = input;
+
+ input_set_capability(input, EV_FF, FF_CONSTANT);
+ input_set_capability(input, EV_FF, FF_PERIODIC);
+ input_set_capability(input, EV_FF, FF_CUSTOM);
+ input_set_capability(input, EV_FF, FF_GAIN);
+
+ ret = input_ff_create(input, HAPTICS_MAX_EFFECTS);
+ if (ret)
+ return ret;
+
+ ff = input->ff;
+ ff->upload = haptics_upload_effect;
+ ff->playback = haptics_playback;
+ ff->erase = haptics_erase;
+ ff->set_gain = haptics_set_gain;
+
+ ret = input_register_device(input);
+ if (ret) {
+ input_ff_destroy(input);
+ return dev_err_probe(h->dev, ret, "failed to register input device\n");
+ }
+
+ return 0;
+}
+
+static void qcom_haptics_remove(struct platform_device *pdev)
+{
+ struct qcom_haptics *h = platform_get_drvdata(pdev);
+
+ /*
+ * Unregister the input device explicitly at the beginning
+ * to avoid the input device being used after the resources
+ * are freed.
+ */
+ input_unregister_device(h->input);
+ disable_delayed_work_sync(&h->play_work);
+ scoped_guard(mutex, &h->play_lock) {
+ haptics_queue_flush(h);
+ haptics_stop_locked(h, true);
+ }
+
+ haptics_enable_module(h, false);
+
+ scoped_guard(mutex, &h->fifo_lock) {
+ for (int i = 0; i < HAPTICS_MAX_EFFECTS; i++) {
+ kvfree(h->effects[i].fifo_data);
+ h->effects[i].fifo_data = NULL;
+ }
+ }
+}
+
+static int qcom_haptics_runtime_suspend(struct device *dev)
+{
+ struct qcom_haptics *h = dev_get_drvdata(dev);
+
+ return haptics_enable_module(h, false);
+}
+
+static int qcom_haptics_runtime_resume(struct device *dev)
+{
+ struct qcom_haptics *h = dev_get_drvdata(dev);
+
+ return haptics_enable_module(h, true);
+}
+
+static int qcom_haptics_suspend(struct device *dev)
+{
+ struct qcom_haptics *h = dev_get_drvdata(dev);
+ int ret;
+
+ disable_delayed_work_sync(&h->play_work);
+ scoped_guard(mutex, &h->play_lock) {
+ haptics_queue_flush(h);
+ haptics_stop_locked(h, true);
+ }
+
+ ret = pm_runtime_force_suspend(dev);
+ if (ret)
+ enable_delayed_work(&h->play_work);
+
+ return ret;
+}
+
+static int qcom_haptics_resume(struct device *dev)
+{
+ struct qcom_haptics *h = dev_get_drvdata(dev);
+
+ enable_delayed_work(&h->play_work);
+
+ return pm_runtime_force_resume(dev);
+}
+
+static const struct dev_pm_ops qcom_haptics_pm_ops = {
+ SYSTEM_SLEEP_PM_OPS(qcom_haptics_suspend, qcom_haptics_resume)
+ RUNTIME_PM_OPS(qcom_haptics_runtime_suspend, qcom_haptics_runtime_resume,
+ NULL)
+};
+
+static const struct of_device_id qcom_haptics_of_match[] = {
+ { .compatible = "qcom,spmi-haptics" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, qcom_haptics_of_match);
+
+static struct platform_driver qcom_haptics_driver = {
+ .probe = qcom_haptics_probe,
+ .remove = qcom_haptics_remove,
+ .driver = {
+ .name = "qcom-spmi-haptics",
+ .of_match_table = qcom_haptics_of_match,
+ .pm = pm_ptr(&qcom_haptics_pm_ops),
+ },
+};
+module_platform_driver(qcom_haptics_driver);
+
+MODULE_DESCRIPTION("Qualcomm SPMI PMIC Haptics driver");
+MODULE_LICENSE("GPL");
--
2.43.0
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox