Linux HAM/Amateur Radio development
 help / color / mirror / Atom feed
* Filter for 430Mhz
@ 2005-08-09 20:51 Stephen Kitchener
  2005-08-09 21:11 ` Dave Platt
  2005-08-09 21:25 ` Richard Stearn
  0 siblings, 2 replies; 4+ messages in thread
From: Stephen Kitchener @ 2005-08-09 20:51 UTC (permalink / raw)
  To: Linux Hams

Hi, 

I have a problem with a really near 430Mz transmitter (my own) that is 
breaking though to the TV. The Transmitter isn't off tune and as far as I 
Know or can see, it isn't producing any side transmissions or birdies. 

So, My question is, does anyone know of a really good filter design or 
commercial filer that will block 430.625 so that it dosn't appear in the 
downlead to the TV.

Thanks
-- 
                 O  o
            _\_   o
         \\/  o\ .
         //\___=
            ''
RHCT 603005411793211
RHCE 804005830215073
Tue, 09 Aug 2005 21:47:47 +0100
 21:47:47 up  3:11,  1 user,  load average: 2.19, 2.38, 2.30
One measure of friendship consists not in the number of things friends
can discuss, but in the number of things they need no longer mention.
		-- Clifton Fadiman

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: Filter for 430Mhz
  2005-08-09 20:51 Filter for 430Mhz Stephen Kitchener
@ 2005-08-09 21:11 ` Dave Platt
  2005-08-09 21:33   ` Stephen Kitchener
  2005-08-09 21:25 ` Richard Stearn
  1 sibling, 1 reply; 4+ messages in thread
From: Dave Platt @ 2005-08-09 21:11 UTC (permalink / raw)
  To: stephen; +Cc: linux-hams

> I have a problem with a really near 430Mz transmitter (my own) that is 
> breaking though to the TV. The Transmitter isn't off tune and as far as I 
> Know or can see, it isn't producing any side transmissions or birdies. 

I had similar problems with my 2-meter transmissions affecting all the TVs
in the house.

The root of the problem was the use of a cheap Radio Shack TV signal
amplifier and distribution box.  The strong local signal was overdriving
the amplifier (probably a 1- or 2-transistor broadband design) and causing
it to distort every signal passing through it.

You may be running into a similar problem, even if you don't have a
separate distribution amplifier.  TV tuner circuits are often optimized
for weak-signal conditions, and may not have a high enough IP3 to hold
off a strong local signal.  This "fundamental overload" can't be cured
at the transmitter, as you clearly understand - you have to keep the strong
signal out of the electronics which were being overdriven.

> So, My question is, does anyone know of a really good filter design or 
> commercial filer that will block 430.625 so that it dosn't appear in the 
> downlead to the TV.

You'll need a notch or bandstop filter, or a set of paralleled bandpass 
filters, to allow the TV frequencies through and block the 430 MHz signal.
A notch or bandstop will probably be the best way to go.

The solution I found (after searching around for quite a while) is
a notch filter made by the Tin Lee company in Canada.  They specialize
in TV filters of various sorts, and their selection is much richer
than I was able to find via any local supplier. 

The one I bought was one of their CR7 models - a band-stop
type which knocks out everything from 130 MHz to 175 MHz.
Mounted right up at the antenna, it does a beautiful job...
the overload/interference problem has gone away entirely.

I suggest that you contact them at www.tinlee.com, and give them
the details of the frequency range(s) you want to pass and which
you wish to notch out.  They may have a stock model which will
do what you want, they have some tunable models, and if all
else fails I'm sure they can build you a custom trap against
the frequency you're concerned about.

You could try building a coaxial-trap notch (e.g. a quarter-wave
open section of coax, or a half-wave shorted section of coax,
connected in parallel with the feedline) but this might have
adverse effects on other frequencies.

73,

	Dave AE6EO

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: Filter for 430Mhz
  2005-08-09 20:51 Filter for 430Mhz Stephen Kitchener
  2005-08-09 21:11 ` Dave Platt
@ 2005-08-09 21:25 ` Richard Stearn
  1 sibling, 0 replies; 4+ messages in thread
From: Richard Stearn @ 2005-08-09 21:25 UTC (permalink / raw)
  To: Linux Hams

Stephen Kitchener wrote:
> Hi, 
> 
> I have a problem with a really near 430Mz transmitter (my own) that is 
> breaking though to the TV. The Transmitter isn't off tune and as far as I 
> Know or can see, it isn't producing any side transmissions or birdies. 
> 
> So, My question is, does anyone know of a really good filter design or 
> commercial filer that will block 430.625 so that it dosn't appear in the 
> downlead to the TV.
> 
> Thanks

Try:
	http://www.ifwtech.co.uk/g3sek/swxfiltr/swxfiltr.htm

Bottom of the page:
	UHF TV Bandpass Filter (432MHz reject)

I use a 144MHz filter in the broadcast radio aerial and the 430MHz filter
in the TV downlead. Then combine both downleads into a distribution amp.

All the bits are fitted inside an old biscuit tin with clampon ferrites
as feed-throughs.

It is not perfect but does reduce the interference to an acceptable level,
i.e. the rest of the family does not notice it.

It is worth noting that digital TV is _much_ less tolerant of interference
than the analogue system.

-- 
73 de g1sog
	Richard

^ permalink raw reply	[flat|nested] 4+ messages in thread

* Re: Filter for 430Mhz
  2005-08-09 21:11 ` Dave Platt
@ 2005-08-09 21:33   ` Stephen Kitchener
  0 siblings, 0 replies; 4+ messages in thread
From: Stephen Kitchener @ 2005-08-09 21:33 UTC (permalink / raw)
  To: Dave Platt; +Cc: Linux Hams

On Tuesday 09 Aug 2005 22:11, you wrote:
Hi Dave

> > I have a problem with a really near 430Mz transmitter (my own) that is
> > breaking though to the TV. The Transmitter isn't off tune and as far as I
> > Know or can see, it isn't producing any side transmissions or birdies.
>
> I had similar problems with my 2-meter transmissions affecting all the TVs
> in the house.
>
> The root of the problem was the use of a cheap Radio Shack TV signal
> amplifier and distribution box.  The strong local signal was overdriving
> the amplifier (probably a 1- or 2-transistor broadband design) and causing
> it to distort every signal passing through it.
>
> You may be running into a similar problem, even if you don't have a
> separate distribution amplifier.  TV tuner circuits are often optimized
> for weak-signal conditions, and may not have a high enough IP3 to hold
> off a strong local signal.  This "fundamental overload" can't be cured
> at the transmitter, as you clearly understand - you have to keep the strong
> signal out of the electronics which were being overdriven.
>
> > So, My question is, does anyone know of a really good filter design or
> > commercial filer that will block 430.625 so that it dosn't appear in the
> > downlead to the TV.
>
> You'll need a notch or bandstop filter, or a set of paralleled bandpass
> filters, to allow the TV frequencies through and block the 430 MHz signal.
> A notch or bandstop will probably be the best way to go.
>
> The solution I found (after searching around for quite a while) is
> a notch filter made by the Tin Lee company in Canada.  They specialize
> in TV filters of various sorts, and their selection is much richer
> than I was able to find via any local supplier.

Thanks for the quick answer - I will look at the site.
Wonder what the deliver time is to the UK :-)...
>
> The one I bought was one of their CR7 models - a band-stop
> type which knocks out everything from 130 MHz to 175 MHz.
> Mounted right up at the antenna, it does a beautiful job...
> the overload/interference problem has gone away entirely.
>
> I suggest that you contact them at www.tinlee.com, and give them
> the details of the frequency range(s) you want to pass and which
> you wish to notch out.  They may have a stock model which will
> do what you want, they have some tunable models, and if all
> else fails I'm sure they can build you a custom trap against
> the frequency you're concerned about.
>
> You could try building a coaxial-trap notch (e.g. a quarter-wave
> open section of coax, or a half-wave shorted section of coax,
> connected in parallel with the feedline) but this might have
> adverse effects on other frequencies.

I did try that route , but unless I was doing it wrong, It didn't seem to have 
any effect, so I am down to a notch filter or/and a single channle filter, 
these (unless you know) are made so that they only pass the TV channels in my 
area (they are setup specifically), but they cost £150 as fas as I know...

>
> 73,

Thanks again
73's

Steve
>
> 	Dave AE6EO

-- 
                 O  o
            _\_   o
         \\/  o\ .
         //\___=
            ''
RHCT 603005411793211
RHCE 804005830215073
Tue, 09 Aug 2005 22:28:50 +0100
 22:28:50 up  3:52,  1 user,  load average: 2.00, 2.55, 2.43
You have not converted a man because you have silenced him.
		-- John Viscount Morley
-
To unsubscribe from this list: send the line "unsubscribe linux-hams" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~2005-08-09 21:33 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-08-09 20:51 Filter for 430Mhz Stephen Kitchener
2005-08-09 21:11 ` Dave Platt
2005-08-09 21:33   ` Stephen Kitchener
2005-08-09 21:25 ` Richard Stearn

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox