From: Marc Kleine-Budde <mkl@pengutronix.de>
To: netdev@vger.kernel.org
Cc: davem@davemloft.net, kuba@kernel.org, linux-can@vger.kernel.org,
kernel@pengutronix.de,
Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>,
"Rob Herring (Arm)" <robh@kernel.org>,
Geert Uytterhoeven <geert+renesas@glider.be>,
Marc Kleine-Budde <mkl@pengutronix.de>
Subject: [PATCH net-next 08/37] dt-bindings: can: renesas,rcar-canfd: Document RZ/G3S SoC
Date: Fri, 9 Oct 2026 15:27:40 +0200 [thread overview]
Message-ID: <20261009134323.64064-9-mkl@pengutronix.de> (raw)
In-Reply-To: <20261009134323.64064-1-mkl@pengutronix.de>
From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
The CAN FD controller found on the Renesas RZ/G3S SoC is largely compatible
with the variant present on the RZ/G3E SoC. The main differences are:
- the RZ/G3S provides only two CAN FD channels
- the RZ/G3S supports only CAN FD operation; the Channel n CAN FD
Configuration Register does not implement the bits used to select
classical CAN-only mode (bit 30) or CAN FD-only mode (bit 28);
consequently, bit 31 (CAN FD Frame Distinction Enable) of the same
register is also not implemented
- some bits in several registers (mainly reserved or status bits) are
read-write on the RZ/G3S but read-only on the RZ/G3E; their behavior is
otherwise identical: the bits read back as 0 on both SoCs and software
is allowed to write only 0 to them on the RZ/G3S
- the RZ/G3S provides 256 acceptance filters, compared to 768 on the
RZ/G3E
- the RZ/G3S can use PCLK clock as the CAN FD clock source through an
internal clock divider, while also supporting an external CAN FD clock
source
Since:
- the SoC clock generator provides to the CAN IP only the peripheral and
the RAM clocks
- when sourced from the peripheral clock, the CAN-FD clock is obtained
inside the IP itself by dividing the peripheral clock
- the assigned-clocks and assigned-clock-rates properties are specific to
the CAN-FD clock
the assigned-clocks and assigned-clock-rates properties were dropped from
the required properties list of the Renesas RZ/G3S SoC.
Add documentation for the Renesas RZ/G3S SoC.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20260902141544.565763-2-claudiu.beznea+renesas@tuxon.dev
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
---
.../bindings/net/can/renesas,rcar-canfd.yaml | 20 +++++++++++++++++--
1 file changed, 18 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml
index b9d9dd7a7967..bbaaef8f4282 100644
--- a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml
+++ b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml
@@ -13,6 +13,7 @@ properties:
compatible:
oneOf:
- enum:
+ - renesas,r9a08g045-canfd # RZ/G3S
- renesas,r9a09g047-canfd # RZ/G3E
- renesas,r9a09g077-canfd # RZ/T2H
@@ -185,8 +186,6 @@ required:
- clocks
- clock-names
- power-domains
- - assigned-clocks
- - assigned-clock-rates
- channel0
- channel1
@@ -198,6 +197,7 @@ allOf:
compatible:
contains:
enum:
+ - renesas,r9a08g045-canfd
- renesas,rzg2l-canfd
then:
properties:
@@ -266,6 +266,7 @@ allOf:
compatible:
contains:
enum:
+ - renesas,r9a08g045-canfd
- renesas,r9a09g077-canfd
- renesas,rcar-gen3-canfd
- renesas,rzg2l-canfd
@@ -330,6 +331,7 @@ allOf:
compatible:
contains:
enum:
+ - renesas,r9a08g045-canfd
- renesas,r9a09g047-canfd
- renesas,rzg2l-canfd
then:
@@ -350,6 +352,20 @@ allOf:
properties:
reset-names: false
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: renesas,r9a08g045-canfd
+ then:
+ properties:
+ renesas,no-can-fd: false
+ renesas,fd-only: false
+ else:
+ required:
+ - assigned-clocks
+ - assigned-clock-rates
+
unevaluatedProperties: false
examples:
--
2.53.0
next prev parent reply other threads:[~2026-10-09 13:43 UTC|newest]
Thread overview: 57+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-09 13:27 [PATCH net-next 0/37] pull-request: can-next 2026-10-09 Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 01/37] can: dev: can_dropped_invalid_skb: drop CAN XL frames on non-CAN XL devices Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 02/37] can: raw: remove redundant NULL check before netdev_hold() Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 03/37] can: convert unreliable ARPHRD_CAN type checks to robust can_get_ml_priv() Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 04/37] can: proc: reset pkg_stats atomics individually Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 05/37] can: proc: remove pointers from CAN specific proc output Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 06/37] can: j1939: cancel pending address claim timers from j1939_ecu_unmap_all() Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 07/37] can: isotp: check the frame type, not just the length Marc Kleine-Budde
2026-10-09 13:27 ` Marc Kleine-Budde [this message]
2026-10-09 13:27 ` [PATCH net-next 09/37] can: rcar_canfd: Fix typos in macro names Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 10/37] can: skb: make echo skb freeing safe in any IRQ context Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 11/37] can: rcar_canfd: Allow the CAN FD clock to be sourced from fck Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 12/37] can: skb: make CAN skb allocation failure paths IRQ-safe Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 13/37] can: rcar_canfd: Do not set registers selecting the CAN mode Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 14/37] can: dev: can_put_echo_skb(): free skb on invalid echo index Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 15/37] can: rcar_canfd: Add support for Renesas RZ/G3S Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 16/37] dt-bindings: can: renesas,rcar-canfd: Document RZ/G3L SoC Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 17/37] can: rcar_canfd: Derive max_channels from the device tree Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 18/37] dt-bindings: net: can: convert grcan to DT schema Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 19/37] can: rcar_canfd: Add support for Renesas RZ/G3L Marc Kleine-Budde
2026-10-10 14:02 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 20/37] dt-bindings: can: renesas,rcar-canfd: Restrict resets in top-level Marc Kleine-Budde
2026-10-10 14:03 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 21/37] can: grcan: update the binding file reference in the driver comment Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 22/37] can: remove Softing CANcard driver Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 23/37] can: Convert to DEFINE_SIMPLE_DEV_PM_OPS() Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 24/37] can: cc770: don't discard the IRQ lookup error in probe Marc Kleine-Budde
2026-10-10 14:03 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 25/37] can: cc770: fix the clock divider check on the platform bus Marc Kleine-Budde
2026-10-09 13:27 ` [PATCH net-next 26/37] can: ems_usb: use usb_kill_urb() to stop the intr URB Marc Kleine-Budde
2026-10-10 14:03 ` netdev-bot+sashiko
2026-10-09 13:27 ` [PATCH net-next 27/37] can: esd: acc_start_xmit(): do not touch skb after can_put_echo_skb() Marc Kleine-Budde
2026-10-10 14:03 ` netdev-bot+sashiko
2026-10-09 13:28 ` [PATCH net-next 28/37] can: flexcan: flexcan_setup_stop_mode_gpr: fix OF node reference leak Marc Kleine-Budde
2026-10-09 13:28 ` [PATCH net-next 29/37] can: f81604: f81604_close(): fix use-after-free on disconnect Marc Kleine-Budde
2026-10-10 14:03 ` netdev-bot+sashiko
2026-10-09 13:28 ` [PATCH net-next 30/37] can: hi311x: drop hi3110_lock before free_irq() on open failure Marc Kleine-Budde
2026-10-10 14:03 ` netdev-bot+sashiko
2026-10-09 13:28 ` [PATCH net-next 31/37] can: kvaser_usb: refactor endpoint lookup Marc Kleine-Budde
2026-10-09 13:28 ` [PATCH net-next 32/37] can: kvaser_usb: validate command format before parsing in hydra receive path Marc Kleine-Budde
2026-10-09 13:28 ` [PATCH net-next 33/37] can: kvaser_pciefd: fix use-after-free in bec poll timer Marc Kleine-Budde
2026-10-09 13:28 ` [PATCH net-next 34/37] can: mcp251xfd: mcp251xfd_probe(): reject devices without match data Marc Kleine-Budde
2026-10-09 13:28 ` [PATCH net-next 35/37] can: sun4i_can: sun4ican_probe(): fix clk leak Marc Kleine-Budde
2026-10-10 14:03 ` netdev-bot+sashiko
2026-10-09 13:28 ` [PATCH net-next 36/37] can: ucan: fix repeated word 'is' in comment Marc Kleine-Budde
2026-10-09 13:28 ` [PATCH net-next 37/37] can: xilinx_can: set CAN FD flags on received frames Marc Kleine-Budde
2026-10-09 13:57 ` [PATCH net-next 0/37] pull-request: can-next 2026-10-09 Marc Kleine-Budde
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261009134323.64064-9-mkl@pengutronix.de \
--to=mkl@pengutronix.de \
--cc=claudiu.beznea.uj@bp.renesas.com \
--cc=davem@davemloft.net \
--cc=geert+renesas@glider.be \
--cc=kernel@pengutronix.de \
--cc=kuba@kernel.org \
--cc=linux-can@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox