* [Bluez-users] Help with Digianswer protocol analyzer
@ 2005-10-13 10:30 Jonathan Leong
2005-10-13 11:06 ` Marcel Holtmann
0 siblings, 1 reply; 6+ messages in thread
From: Jonathan Leong @ 2005-10-13 10:30 UTC (permalink / raw)
To: bluez-users
[-- Attachment #1: Type: text/plain, Size: 653 bytes --]
Hello,
I have a digianswer protocol analyzer connected to my computer via usb.
Problem is I can't seem to get it up running.
hciconfig -a , produces the following
hci0: Type: USB
BD Address: 00:00:00:00:00:00 ACL MTU: 0 :0 SCO MTU: 0:0
DOWN
hciconfig hci0 up
Can't init device hci0: Commection timed out (110)
I am currently slackware 2.6.11.8, with bluez-libs 2.21 installed.
lsmod displays the following
hci_usb 14344 0
bluetooth 43268 1 hci_usb
I'm guessing it detects the device but I havent got the right driver loaded?
Warmest Regards,
Jonathan Leong
[-- Attachment #2: Type: text/html, Size: 2487 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: [Bluez-users] Help with Digianswer protocol analyzer
2005-10-13 10:30 [Bluez-users] Help with Digianswer protocol analyzer Jonathan Leong
@ 2005-10-13 11:06 ` Marcel Holtmann
2005-10-13 12:51 ` Jonathan Leong
0 siblings, 1 reply; 6+ messages in thread
From: Marcel Holtmann @ 2005-10-13 11:06 UTC (permalink / raw)
To: bluez-users
Hi Jonathan,
> I have a digianswer protocol analyzer connected to my computer via
> usb.
> Problem is I can't seem to get it up running.
>
> hciconfig -a , produces the following
>
> hci0: Type: USB
> BD Address: 00:00:00:00:00:00 ACL MTU: 0 :0 SCO MTU: 0:0
> DOWN
>
> hciconfig hci0 up
>
> Can't init device hci0: Commection timed out (110)
>
> I am currently slackware 2.6.11.8, with bluez-libs 2.21 installed.
>
> lsmod displays the following
>
> hci_usb 14344 0
> bluetooth 43268 1 hci_usb
>
>
> I'm guessing it detects the device but I havent got the right driver
> loaded?
show me the content of /proc/bus/usb/devices and check if you have the
bpa10x kernel driver. If not then you might need to install a newer
kernel.
Regards
Marcel
-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions,
and more. http://solutions.newsforge.com/ibmarch.tmpl
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Bluez-users] Help with Digianswer protocol analyzer
2005-10-13 11:06 ` Marcel Holtmann
@ 2005-10-13 12:51 ` Jonathan Leong
2005-10-13 13:30 ` Marcel Holtmann
0 siblings, 1 reply; 6+ messages in thread
From: Jonathan Leong @ 2005-10-13 12:51 UTC (permalink / raw)
To: bluez-users
Hi Marcel,
> show me the content of /proc/bus/usb/devices and check if you have the
> bpa10x kernel driver. If not then you might need to install a newer
> kernel.
here we go,
T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS= 8 #Cfgs= 1
P: Vendor=08fd ProdID=0001 Rev= 1.00
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=300mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
E: Ad=83(I) Atr=01(Isoc) MxPS= 16 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 16 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
Meanwhile, I'll go upgrade my kernel to 2.6.13 and get it patch.
I'll post the results in a bit.
Warmest Regards,
Jonathan Leong
-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions,
and more. http://solutions.newsforge.com/ibmarch.tmpl
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Bluez-users] Help with Digianswer protocol analyzer
2005-10-13 12:51 ` Jonathan Leong
@ 2005-10-13 13:30 ` Marcel Holtmann
2005-10-13 13:56 ` Jonathan Leong
0 siblings, 1 reply; 6+ messages in thread
From: Marcel Holtmann @ 2005-10-13 13:30 UTC (permalink / raw)
To: bluez-users
Hi Jonathan,
> > show me the content of /proc/bus/usb/devices and check if you have the
> > bpa10x kernel driver. If not then you might need to install a newer
> > kernel.
>
> here we go,
>
> T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
> D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS= 8 #Cfgs= 1
> P: Vendor=08fd ProdID=0001 Rev= 1.00
> C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=300mA
> I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
> I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 16 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 16 Ivl=1ms
> I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms
> I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
> E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
> E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
>
> Meanwhile, I'll go upgrade my kernel to 2.6.13 and get it patch.
> I'll post the results in a bit.
this won't help, I think. Is this the BPA-100 or the BPA-105?
Regards
Marcel
-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions,
and more. http://solutions.newsforge.com/ibmarch.tmpl
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Bluez-users] Help with Digianswer protocol analyzer
2005-10-13 13:30 ` Marcel Holtmann
@ 2005-10-13 13:56 ` Jonathan Leong
2005-10-13 14:11 ` Marcel Holtmann
0 siblings, 1 reply; 6+ messages in thread
From: Jonathan Leong @ 2005-10-13 13:56 UTC (permalink / raw)
To: bluez-users
Hi Marcel,
It should be the BPA-100. According to your website, I reckon it belongs to
the first generation (08fd:0001) .
The device isnt marked Tektronix but Digianswer A/S Bluetooth Protocol
Analyzer but shouldn't be much of a difference.
The loaded driver is hci_usb instead of bpa10x, maybe the driver was
missing? modprobe bpa10x.ko gave me an error.
Regards,
Jonathan Leong
----- Original Message -----
From: "Marcel Holtmann" <marcel@holtmann.org>
To: <bluez-users@lists.sourceforge.net>
Sent: Thursday, October 13, 2005 9:30 PM
Subject: Re: [Bluez-users] Help with Digianswer protocol analyzer
> Hi Jonathan,
>
>> > show me the content of /proc/bus/usb/devices and check if you have the
>> > bpa10x kernel driver. If not then you might need to install a newer
>> > kernel.
>>
>> here we go,
>>
>> T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
>> D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS= 8 #Cfgs= 1
>> P: Vendor=08fd ProdID=0001 Rev= 1.00
>> C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=300mA
>> I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
>> E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
>> E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
>> E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
>> I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
>> E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
>> E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
>> I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
>> E: Ad=83(I) Atr=01(Isoc) MxPS= 16 Ivl=1ms
>> E: Ad=03(O) Atr=01(Isoc) MxPS= 16 Ivl=1ms
>> I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
>> E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms
>> E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms
>> I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=hci_usb
>> E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
>> E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
>>
>> Meanwhile, I'll go upgrade my kernel to 2.6.13 and get it patch.
>> I'll post the results in a bit.
>
> this won't help, I think. Is this the BPA-100 or the BPA-105?
>
> Regards
>
> Marcel
>
>
>
>
> -------------------------------------------------------
> This SF.Net email is sponsored by:
> Power Architecture Resource Center: Free content, downloads, discussions,
> and more. http://solutions.newsforge.com/ibmarch.tmpl
> _______________________________________________
> Bluez-users mailing list
> Bluez-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/bluez-users
>
-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions,
and more. http://solutions.newsforge.com/ibmarch.tmpl
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Bluez-users] Help with Digianswer protocol analyzer
2005-10-13 13:56 ` Jonathan Leong
@ 2005-10-13 14:11 ` Marcel Holtmann
0 siblings, 0 replies; 6+ messages in thread
From: Marcel Holtmann @ 2005-10-13 14:11 UTC (permalink / raw)
To: bluez-users
Hi Jonathan,
> It should be the BPA-100. According to your website, I reckon it belongs to
> the first generation (08fd:0001) .
> The device isnt marked Tektronix but Digianswer A/S Bluetooth Protocol
> Analyzer but shouldn't be much of a difference.
they are all the same. Now they are owned by Frontline.
> The loaded driver is hci_usb instead of bpa10x, maybe the driver was
> missing? modprobe bpa10x.ko gave me an error.
So it seems we have to change something to adapt it for the BPA-100. I
need that device to really figure out, what is going on and what we have
to do.
Regards
Marcel
-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions,
and more. http://solutions.newsforge.com/ibmarch.tmpl
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2005-10-13 14:11 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-10-13 10:30 [Bluez-users] Help with Digianswer protocol analyzer Jonathan Leong
2005-10-13 11:06 ` Marcel Holtmann
2005-10-13 12:51 ` Jonathan Leong
2005-10-13 13:30 ` Marcel Holtmann
2005-10-13 13:56 ` Jonathan Leong
2005-10-13 14:11 ` Marcel Holtmann
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.