From: Tom <Tom.Rix@windriver.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [GIT PULL] Pull request: u-boot-imx
Date: Thu, 04 Mar 2010 10:03:56 -0600 [thread overview]
Message-ID: <4B8FD9EC.5030405@windriver.com> (raw)
In-Reply-To: <4B8D5CCC.6010401@denx.de>
There are some compiler warnings.
These should be resolved.
mx51evk.ERR
soc.c: In function 'print_cpuinfo':
soc.c:68: warning: implicit declaration of function 'get_mcu_main_clk'
soc.c: In function 'cpu_mmc_init':
soc.c:99: warning: implicit declaration of function 'fsl_esdhc_mmc_init'
clock.c:45: warning: initialization makes pointer from integer without a cast
speed.c: In function 'get_clocks':
speed.c:35: warning: implicit declaration of function 'mxc_get_clock'
mx51evk.c: In function 'board_init':
mx51evk.c:354: warning: implicit declaration of function 'get_cpu_rev'
Tom
Stefano Babic wrote:
> Hi Tom,
>
> The following changes since commit f3651764e57e353251695691677bd95ba5a420bc:
> Frans Meulenbroeks (1):
> cmd_itest.c: fix pointer dereferencing
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-imx master
>
> John Rigby (5):
> mxc_serial replace platform specific clock
> Add support for Freescale MX25 SOC
> fec_mxc: cleanup and factor out MX27 dependencies
> fec_mxc: add MX25 support
> Add support for KARO TX25 board
>
> Stefano Babic (9):
> MX51: Add initial support for the Freescale MX51
> MX51: Add register definitions
> MX51: Add pin and multiplexer definitions.
> serial_mxc: add support for MX51 processor
> mmc: check correctness of the voltage mask in ocr
> MMC: add weak function to detect MMC/SD card
> ARM: add accessors functions
> fsl_esdhc: add support for mx51 processor
> Add initial support for Freescale mx51evk board
>
> MAINTAINERS | 8 +
> MAKEALL | 1 +
> Makefile | 8 +
> board/freescale/mx51evk/Makefile | 48 ++++
> board/freescale/mx51evk/config.mk | 25 ++
> board/freescale/mx51evk/imximage.cfg | 119 +++++++++
> board/freescale/mx51evk/mx51evk.c | 406
> ++++++++++++++++++++++++++++
> board/freescale/mx51evk/mx51evk.h | 51 ++++
> board/karo/tx25/Makefile | 51 ++++
> board/karo/tx25/config.mk | 5 +
> board/karo/tx25/lowlevel_init.S | 131 +++++++++
> board/karo/tx25/tx25.c | 176 +++++++++++++
> cpu/arm926ejs/mx25/Makefile | 46 ++++
> cpu/arm926ejs/mx25/generic.c | 263 +++++++++++++++++++
> cpu/arm926ejs/mx25/reset.c | 56 ++++
> cpu/arm926ejs/mx25/timer.c | 187 +++++++++++++
> cpu/arm926ejs/mx27/generic.c | 5 +
> cpu/arm_cortexa8/mx51/Makefile | 48 ++++
> cpu/arm_cortexa8/mx51/clock.c | 293 +++++++++++++++++++++
> cpu/arm_cortexa8/mx51/iomux.c | 165 ++++++++++++
> cpu/arm_cortexa8/mx51/lowlevel_init.S | 289 ++++++++++++++++++++
> cpu/arm_cortexa8/mx51/soc.c | 109 ++++++++
> cpu/arm_cortexa8/mx51/speed.c | 38 +++
> cpu/arm_cortexa8/mx51/timer.c | 119 +++++++++
> cpu/arm_cortexa8/mx51/u-boot.lds | 61 +++++
> drivers/mmc/fsl_esdhc.c | 149 +++++++----
> drivers/mmc/mmc.c | 17 ++-
> drivers/net/fec_mxc.c | 44 +++-
> drivers/net/fec_mxc.h | 32 +++-
> drivers/serial/serial_mxc.c | 28 ++-
> include/asm-arm/arch-mx25/clock.h | 36 +++
> include/asm-arm/arch-mx25/imx-regs.h | 316 ++++++++++++++++++++++
> include/asm-arm/arch-mx25/imx25-pinmux.h | 421
> ++++++++++++++++++++++++++++++
> include/asm-arm/arch-mx27/clock.h | 3 +
> include/asm-arm/arch-mx31/mx31.h | 1 +
> include/asm-arm/arch-mx51/asm-offsets.h | 50 ++++
> include/asm-arm/arch-mx51/clock.h | 31 +++
> include/asm-arm/arch-mx51/crm_regs.h | 192 ++++++++++++++
> include/asm-arm/arch-mx51/imx-regs.h | 282 ++++++++++++++++++++
> include/asm-arm/arch-mx51/iomux.h | 193 ++++++++++++++
> include/asm-arm/arch-mx51/mx51_pins.h | 374 ++++++++++++++++++++++++++
> include/asm-arm/global_data.h | 3 +
> include/asm-arm/io.h | 55 ++++
> include/configs/mx51evk.h | 172 ++++++++++++
> include/configs/tx25.h | 179 +++++++++++++
> include/fsl_esdhc.h | 27 ++
> include/mmc.h | 1 +
> lib_arm/board.c | 3 +
> nand_spl/board/karo/tx25/Makefile | 78 ++++++
> nand_spl/board/karo/tx25/config.mk | 1 +
> nand_spl/board/karo/tx25/u-boot.lds | 58 ++++
> 51 files changed, 5386 insertions(+), 68 deletions(-)
> create mode 100644 board/freescale/mx51evk/Makefile
> create mode 100644 board/freescale/mx51evk/config.mk
> create mode 100644 board/freescale/mx51evk/imximage.cfg
> create mode 100644 board/freescale/mx51evk/mx51evk.c
> create mode 100644 board/freescale/mx51evk/mx51evk.h
> create mode 100644 board/karo/tx25/Makefile
> create mode 100644 board/karo/tx25/config.mk
> create mode 100644 board/karo/tx25/lowlevel_init.S
> create mode 100644 board/karo/tx25/tx25.c
> create mode 100644 cpu/arm926ejs/mx25/Makefile
> create mode 100644 cpu/arm926ejs/mx25/generic.c
> create mode 100644 cpu/arm926ejs/mx25/reset.c
> create mode 100644 cpu/arm926ejs/mx25/timer.c
> create mode 100644 cpu/arm_cortexa8/mx51/Makefile
> create mode 100644 cpu/arm_cortexa8/mx51/clock.c
> create mode 100644 cpu/arm_cortexa8/mx51/iomux.c
> create mode 100644 cpu/arm_cortexa8/mx51/lowlevel_init.S
> create mode 100644 cpu/arm_cortexa8/mx51/soc.c
> create mode 100644 cpu/arm_cortexa8/mx51/speed.c
> create mode 100644 cpu/arm_cortexa8/mx51/timer.c
> create mode 100644 cpu/arm_cortexa8/mx51/u-boot.lds
> create mode 100644 include/asm-arm/arch-mx25/clock.h
> create mode 100644 include/asm-arm/arch-mx25/imx-regs.h
> create mode 100644 include/asm-arm/arch-mx25/imx25-pinmux.h
> create mode 100644 include/asm-arm/arch-mx51/asm-offsets.h
> create mode 100644 include/asm-arm/arch-mx51/clock.h
> create mode 100644 include/asm-arm/arch-mx51/crm_regs.h
> create mode 100644 include/asm-arm/arch-mx51/imx-regs.h
> create mode 100644 include/asm-arm/arch-mx51/iomux.h
> create mode 100644 include/asm-arm/arch-mx51/mx51_pins.h
> create mode 100644 include/configs/mx51evk.h
> create mode 100644 include/configs/tx25.h
> create mode 100644 nand_spl/board/karo/tx25/Makefile
> create mode 100644 nand_spl/board/karo/tx25/config.mk
> create mode 100644 nand_spl/board/karo/tx25/u-boot.lds
>
next prev parent reply other threads:[~2010-03-04 16:03 UTC|newest]
Thread overview: 116+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-03-02 18:45 [U-Boot] [GIT PULL] Pull request: u-boot-imx Stefano Babic
2010-03-04 16:03 ` Tom [this message]
2010-03-05 14:54 ` Stefano Babic
2010-03-05 17:24 ` Stefano Babic
2010-03-05 14:00 ` Tom
2010-03-05 14:16 ` Stefano Babic
2010-03-05 14:40 ` Tom
2010-03-05 14:48 ` Stefano Babic
-- strict thread matches above, loose matches on Subject: below --
2010-04-06 9:38 Stefano Babic
2010-04-18 11:45 ` Tom Rix
2010-04-19 13:52 Stefano Babic
2010-05-05 8:15 Stefano Babic
[not found] <4BE12AA5.8020605@denx.de>
2010-05-11 15:04 ` Tom Rix
2010-10-07 8:28 Stefano Babic
2010-10-11 8:23 ` Wolfgang Denk
2010-10-14 8:42 Stefano Babic
2010-10-17 17:57 ` Wolfgang Denk
2010-10-19 14:09 Stefano Babic
2010-10-19 18:58 ` Wolfgang Denk
2010-10-28 11:25 Stefano Babic
2010-10-29 19:50 ` Wolfgang Denk
2010-12-09 10:05 stefano babic
2010-12-09 19:54 ` Wolfgang Denk
2011-01-13 6:40 Stefano Babic
2011-01-13 7:20 ` Albert ARIBAUD
2011-01-13 7:23 ` Stefano Babic
2011-01-13 21:30 ` Albert ARIBAUD
2011-01-17 19:10 ` Wolfgang Denk
2011-01-17 19:30 ` Stefano Babic
2011-01-21 9:24 Stefano Babic
2011-01-21 17:33 ` Albert ARIBAUD
2011-02-01 18:13 Stefano Babic
2011-02-01 23:58 ` Albert ARIBAUD
2011-02-13 9:56 Stefano Babic
2011-02-13 11:25 ` Albert ARIBAUD
2011-02-13 11:57 ` Albert ARIBAUD
2011-04-05 13:29 Stefano Babic
2011-04-05 17:13 ` Albert ARIBAUD
2011-04-22 12:50 Stefano Babic
2011-05-09 11:49 Stefano Babic
2011-05-10 21:55 ` Albert ARIBAUD
2011-05-11 5:50 ` Stefano Babic
2011-05-11 20:56 ` Albert ARIBAUD
2011-05-11 20:58 ` Albert ARIBAUD
2011-05-20 15:58 Stefano Babic
2011-05-20 18:35 ` Albert ARIBAUD
2011-06-08 11:36 Stefano Babic
2011-06-08 20:08 ` Albert ARIBAUD
2011-06-15 9:28 Stefano Babic
2011-06-17 19:24 ` Albert ARIBAUD
2011-06-17 19:37 ` Albert ARIBAUD
2011-06-18 9:59 ` Stefano Babic
2011-06-18 11:11 ` Albert ARIBAUD
2011-06-30 9:38 Stefano Babic
2011-06-30 10:52 ` Albert ARIBAUD
2011-07-13 14:25 Stefano Babic
2011-07-14 13:42 ` Albert ARIBAUD
2011-07-18 12:45 Stefano Babic
2011-07-18 13:38 ` Albert ARIBAUD
2011-08-12 14:08 Stefano Babic
2011-08-12 17:53 ` Albert ARIBAUD
2011-08-26 9:31 Stefano Babic
2011-08-26 9:38 ` Stefano Babic
2011-08-26 14:23 Stefano Babic
2011-08-30 9:18 ` Albert ARIBAUD
2011-09-08 14:34 Stefano Babic
2011-09-08 14:59 ` Albert ARIBAUD
2011-10-17 8:05 Stefano Babic
2011-10-18 18:12 ` Albert ARIBAUD
2011-10-19 9:30 ` Stefano Babic
2011-10-19 11:25 ` Albert ARIBAUD
2011-10-28 12:37 Stefano Babic
2011-10-28 15:20 ` Albert ARIBAUD
2011-11-04 6:47 Stefano Babic
2011-11-04 21:11 ` Albert ARIBAUD
2011-11-11 10:40 Stefano Babic
2011-11-15 21:24 ` Albert ARIBAUD
2011-12-01 16:14 Stefano Babic
2011-12-05 16:57 ` Albert ARIBAUD
2011-12-05 17:19 ` Stefano Babic
2011-12-05 17:22 Stefano Babic
2011-12-05 17:27 ` Albert ARIBAUD
2011-12-09 14:34 Stefano Babic
2011-12-09 16:40 ` Albert ARIBAUD
2011-12-19 7:45 Stefano Babic
2011-12-19 8:39 ` Albert ARIBAUD
2012-01-04 16:57 Stefano Babic
2012-01-04 17:41 ` Fabio Estevam
2012-01-04 17:56 ` Stefano Babic
2012-01-12 22:01 ` Albert ARIBAUD
2012-01-22 13:06 Stefano Babic
2012-02-04 16:57 ` Albert ARIBAUD
2012-02-05 13:32 ` Stefano Babic
2012-02-12 16:06 Stefano Babic
2012-02-13 8:03 ` Albert ARIBAUD
2012-02-20 7:10 Stefano Babic
2012-02-20 7:54 ` Albert ARIBAUD
2012-03-03 11:38 Stefano Babic
2012-03-05 12:37 ` Albert ARIBAUD
2012-03-08 7:52 Stefano Babic
2012-03-26 20:45 ` Albert ARIBAUD
2012-03-26 21:08 ` Albert ARIBAUD
2012-03-27 7:39 ` Stefano Babic
2012-04-11 14:22 Stefano Babic
2012-04-16 13:04 ` Albert ARIBAUD
2012-05-09 16:38 Stefano Babic
2012-05-15 6:24 ` Albert ARIBAUD
2012-07-02 18:03 Stefano Babic
2012-07-05 8:23 ` Albert ARIBAUD
2012-08-07 16:00 Stefano Babic
2012-08-27 6:41 Stefano Babic
2012-09-01 12:57 ` Albert ARIBAUD
2012-09-17 13:53 Stefano Babic
2012-09-20 22:46 ` Albert ARIBAUD
2012-09-28 15:39 Stefano Babic
2012-09-29 9:48 ` Albert ARIBAUD
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4B8FD9EC.5030405@windriver.com \
--to=tom.rix@windriver.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.