[PATCH 5/9] ARM: at91/dt: add mmc0 slot0 support to at91rm9200ek board

[b.brezillon@overkiz.com (boris brezillon)]

On 20/11/2013 15:59, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 13:06 Wed 28 Aug     , Boris BREZILLON wrote:
>> Add slot0 of mmc0 pinctrl pins definitions:
>>   - detect pin
>>   - write protect pin
>>   - enable slot0 pin: this pin is connected to an external switch which
>>     enable mmc0 slot0 or spi dataflash connected to cs3
>>
>> The mmc0 device is not enabled, as it depends on the choosen functionnality
>> (spi cs3 or mmc0 slot0).
>>
>> Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
>> ---
>>   arch/arm/boot/dts/at91rm9200ek.dts |   35 +++++++++++++++++++++++++++++++++++
>>   1 file changed, 35 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/at91rm9200ek.dts
>> index f2d6d79..2bad423 100644
>> --- a/arch/arm/boot/dts/at91rm9200ek.dts
>> +++ b/arch/arm/boot/dts/at91rm9200ek.dts
>> @@ -39,6 +39,23 @@
>>   						atmel,pins = <AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>;
>>   					};
>>   				};
>> +
>> +				mmc0 {
>> +					pinctrl_mmc0_slot0_detect: mmc0_slot0_detect-0 {
>> +						atmel,pins =
>> +							<AT91_PIOB 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
>> +					};
>> +
>> +					pinctrl_mmc0_slot0_write_protect: mmc0_slot0_write_protect-0 {
>> +						atmel,pins =
>> +							<AT91_PIOA 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
>> +					};
>> +
>> +					pinctrl_mmc0_slot0_switch: mmc0_slot0_switch-0 {
>> +						atmel,pins =
>> +							<AT91_PIOB 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(1))>;
>> +					};
> nack this is a regulator the pinctrl API is not done for gpio default value

I know this can be represented as a regulator, but looking at the 
datasheet, this looks more
like a switch than a regulator.

Anyway, why didn't you told me that when I proposed the OUTPUT support 
for at91 pinctrl driver ?
And BTW pinctrl OUTPUT config is already supported by some pinctrl drivers
( 
http://lxr.free-electrons.com/source/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt#L159).

>> +				};
>>   			};
>>   
>>   			dbgu: serial at fffff200 {
>> @@ -84,6 +101,24 @@
>>   					reg = <0>;
>>   				};
>>   			};
>> +
>> +			mmc0: mmc at fffb4000 {
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +				pinctrl-0 = <&pinctrl_mmc0_clk
>> +					     &pinctrl_mmc0_slot0_cmd_dat0
>> +					     &pinctrl_mmc0_slot0_dat1_3
>> +					     &pinctrl_mmc0_slot0_detect
>> +					     &pinctrl_mmc0_slot0_write_protect
>> +					     &pinctrl_mmc0_slot0_switch>;
>> +
>> +				slot0: slot at 0 {
>> +					reg = <0>;
>> +					bus-width = <4>;
>> +					cd-gpios = <&pioB 27 GPIO_ACTIVE_HIGH>;
>> +					wp-gpios = <&pioA 17 GPIO_ACTIVE_HIGH>;
>> +				};
>> +			};
>>   		};
>>   
>>   		usb0: ohci at 00300000 {
>> -- 
>> 1.7.9.5
>>