[PATCH 1/9] ARM: at91/dt: add rm9200 spi0 chip select pins definitions

[b.brezillon@overkiz.com (boris brezillon)]

On 20/11/2013 16:59, boris brezillon wrote:
> On 20/11/2013 15:56, Jean-Christophe PLAGNIOL-VILLARD wrote:
>> On 13:02 Wed 28 Aug     , Boris BREZILLON wrote:
>>> Add spi0 cs pinctrl pins definitions.
>>>
>>> Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
>>> ---
>>>   arch/arm/boot/dts/at91rm9200.dtsi |   20 ++++++++++++++++++++
>>>   1 file changed, 20 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/at91rm9200.dtsi
>>> b/arch/arm/boot/dts/at91rm9200.dtsi
>>> index f770655..69b76c7 100644
>>> --- a/arch/arm/boot/dts/at91rm9200.dtsi
>>> +++ b/arch/arm/boot/dts/at91rm9200.dtsi
>>> @@ -486,6 +486,26 @@
>>>                                AT91_PIOA 1 AT91_PERIPH_A
>>> AT91_PINCTRL_NONE    /* PA1 periph A SPI0_MOSI pin */
>>>                                AT91_PIOA 2 AT91_PERIPH_A
>>> AT91_PINCTRL_NONE>;    /* PA2 periph A SPI0_SPCK pin */
>>>                       };
>>> +
>>> +                    pinctrl_spi0_cs0: spi0_cs0-0 {
>>> +                        atmel,pins =
>>> +                            <AT91_PIOA 3 AT91_PERIPH_A
>>> AT91_PINCTRL_NONE>;    /* PA3 periph A SPI0_NPCS0 pin */
>>> +                    };
>>> +
>>> +                    pinctrl_spi0_cs1: spi0_cs1-0 {
>>> +                        atmel,pins =
>>> +                            <AT91_PIOA 4 AT91_PERIPH_GPIO
>>> AT91_PINCTRL_MULTI_DRIVE>;    /* PA4 GPIO SPI0_NPCS1 pin */
>>> +                    };
>>> +
>>> +                    pinctrl_spi0_cs2: spi0_cs2-0 {
>>> +                        atmel,pins =
>>> +                            <AT91_PIOA 5 AT91_PERIPH_GPIO
>>> AT91_PINCTRL_MULTI_DRIVE>;    /* PA5 GPIO SPI0_NPCS2 pin */
>>> +                    };
>>> +
>>> +                    pinctrl_spi0_cs3: spi0_cs3-0 {
>>> +                        atmel,pins =
>>> +                            <AT91_PIOA 6 AT91_PERIPH_GPIO
>>> AT91_PINCTRL_MULTI_DRIVE>;    /* PA6 GPIO SPI0_NPCS3 pin */
>>> +                    };
>> nack the pin are not multidrive there is only one master
> Right, this is a mistake.
>
> But the pins should be configured as OUTPUT with HIGH level
> (see
> http://lxr.free-electrons.com/source/arch/arm/mach-at91/at91rm9200_devices.c#L589).
>

Okay, my mistake again, declaring "cs-gpios" property should suffice 
(the atmel spi driver will configure it accordingly when probing the spi 
device).

>
>>
>> Best Regards,
>> J.
>>>                   };
>>>                   pioA: gpio at fffff400 {
>>> --
>>> 1.7.9.5
>>>
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel