From: Shobhit Kumar <shobhit.kumar@intel.com>
To: intel-gfx <intel-gfx@lists.freedesktop.org>
Cc: jani.nikula@intel.com, vijayakumar.balakrishnan@intel.com,
yogesh.mohan.marimuthu@intel.com
Subject: [PATCH v2 3/7] drm/i915: Compute dsi_clk from pixel clock
Date: Sat, 9 Nov 2013 15:19:04 +0530 [thread overview]
Message-ID: <1383990548-30737-4-git-send-email-shobhit.kumar@intel.com> (raw)
In-Reply-To: <1383990548-30737-1-git-send-email-shobhit.kumar@intel.com>
Pixel clock based calculation is recommended in the MIPI host controller
documentation
v2: Based on review comments from Jani and Ville
- Use dsi_clk in KHz rather than converting in Hz and back to MHz
- RR formula is retained though not used but return dsi_clk in KHz now
- Moved the m-n-p changes into a separate patch
- Removed the parameter check for intel_dsi->dsi_clock_freq. This will be
bought back in if needed when appropriate panel drivers are done
Signed-off-by: Vijayakumar Balakrishnan <vijayakumar.balakrishnan@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
---
drivers/gpu/drm/i915/intel_dsi_pll.c | 46 +++++++++++++++++++++++++++++-----
1 file changed, 40 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_dsi_pll.c b/drivers/gpu/drm/i915/intel_dsi_pll.c
index 44279b2..9f3e6b0 100644
--- a/drivers/gpu/drm/i915/intel_dsi_pll.c
+++ b/drivers/gpu/drm/i915/intel_dsi_pll.c
@@ -50,6 +50,8 @@ static const u32 lfsr_converts[] = {
71, 35 /* 91 - 92 */
};
+#ifdef DSI_CLK_FROM_RR
+
static u32 dsi_rr_formula(const struct drm_display_mode *mode,
int pixel_format, int video_mode_format,
int lane_count, bool eotp)
@@ -121,7 +123,7 @@ static u32 dsi_rr_formula(const struct drm_display_mode *mode,
/* the dsi clock is divided by 2 in the hardware to get dsi ddr clock */
dsi_bit_clock_hz = bytes_per_x_frames_x_lanes * 8;
- dsi_clk = dsi_bit_clock_hz / (1000 * 1000);
+ dsi_clk = dsi_bit_clock_hz / 1000;
if (eotp && video_mode_format == VIDEO_MODE_BURST)
dsi_clk *= 2;
@@ -129,6 +131,38 @@ static u32 dsi_rr_formula(const struct drm_display_mode *mode,
return dsi_clk;
}
+#else
+
+/* Get DSI clock from pixel clock */
+static u32 dsi_clk_from_pclk(const struct drm_display_mode *mode,
+ int pixel_format, int lane_count)
+{
+ u32 dsi_clk_khz;
+ u32 bpp;
+
+ switch (pixel_format) {
+ default:
+ case VID_MODE_FORMAT_RGB888:
+ case VID_MODE_FORMAT_RGB666_LOOSE:
+ bpp = 24;
+ break;
+ case VID_MODE_FORMAT_RGB666:
+ bpp = 18;
+ break;
+ case VID_MODE_FORMAT_RGB565:
+ bpp = 16;
+ break;
+ }
+
+ /* DSI data rate = pixel clock * bits per pixel / lane count
+ pixel clock is converted from KHz to Hz */
+ dsi_clk_khz = DIV_ROUND_CLOSEST(mode->clock * bpp, lane_count);
+
+ return dsi_clk_khz;
+}
+
+#endif
+
#ifdef MNP_FROM_TABLE
struct dsi_clock_table {
@@ -200,13 +234,14 @@ static int dsi_calc_mnp(u32 dsi_clk, struct dsi_mnp *dsi_mnp)
u32 calc_p;
u32 m_seed;
- if (dsi_clk < 300 || dsi_clk > 1150) {
+ /* dsi_clk is expected in KHZ */
+ if (dsi_clk < 300000 || dsi_clk > 1150000) {
DRM_ERROR("DSI CLK Out of Range\n");
return -ECHRNG;
}
ref_clk = 25000;
- target_dsi_clk = dsi_clk * 1000;
+ target_dsi_clk = dsi_clk;
error = 0xFFFFFFFF;
calc_m = 0;
calc_p = 0;
@@ -251,9 +286,8 @@ static void vlv_configure_dsi_pll(struct intel_encoder *encoder)
struct dsi_mnp dsi_mnp;
u32 dsi_clk;
- dsi_clk = dsi_rr_formula(mode, intel_dsi->pixel_format,
- intel_dsi->video_mode_format,
- intel_dsi->lane_count, !intel_dsi->eot_disable);
+ dsi_clk = dsi_clk_from_pclk(mode, intel_dsi->pixel_format,
+ intel_dsi->lane_count);
ret = dsi_calc_mnp(dsi_clk, &dsi_mnp);
if (ret) {
--
1.7.9.5
next prev parent reply other threads:[~2013-11-09 9:41 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-11-09 9:49 [PATCH v2 0/7] drm/i915: Baytrail MIPI DSI support Updated Shobhit Kumar
2013-11-09 9:49 ` [PATCH v2 1/7] drm/i915: Add more dev ops for MIPI sub encoder Shobhit Kumar
2013-11-15 8:29 ` Jani Nikula
2013-11-09 9:49 ` [PATCH v2 2/7] drm/i915: Use FLISDSI interface for band gap reset Shobhit Kumar
2013-11-15 9:10 ` Jani Nikula
2013-11-09 9:49 ` Shobhit Kumar [this message]
2013-11-15 7:22 ` [PATCH v2 3/7] drm/i915: Compute dsi_clk from pixel clock Jani Nikula
2013-11-15 8:40 ` Jani Nikula
2013-11-09 9:49 ` [PATCH v2 4/7] drm/i915: Try harder to get best m, n, p values with minimal error Shobhit Kumar
2013-11-15 7:19 ` Jani Nikula
2013-11-09 9:49 ` [PATCH v2 5/7] drm/i915: Reorganize the DSI enable/disable sequence Shobhit Kumar
2013-11-15 8:27 ` Jani Nikula
2013-11-15 8:55 ` Daniel Vetter
2013-11-20 1:39 ` Shobhit Kumar
2013-12-06 11:20 ` Shobhit Kumar
2013-12-06 11:25 ` Shobhit Kumar
2013-11-09 9:49 ` [PATCH v2 6/7] drm/i915: Remove redundant DSI PLL enabling Shobhit Kumar
2013-11-15 8:41 ` Jani Nikula
2013-11-09 9:49 ` [PATCH v2 7/7] drm/i915: Parametrize the dphy and other spec specific parameters Shobhit Kumar
2013-11-15 7:52 ` Jani Nikula
2013-11-15 8:42 ` Jani Nikula
2013-11-09 10:28 ` [PATCH v2 0/7] drm/i915: Baytrail MIPI DSI support Updated Daniel Vetter
2013-11-11 8:50 ` [Intel-gfx] " Thierry Reding
2013-11-11 10:28 ` Shobhit Kumar
[not found] ` <52A7F4A0.6050902@intel.com>
[not found] ` <CAKMK7uGU=R3j1TDgLZzUKtztrY6P_akzHHeWEQy_Jw7DdQpiTg@mail.gmail.com>
[not found] ` <87r49j60ym.fsf@intel.com>
[not found] ` <52A86FF2.5050200@intel.com>
[not found] ` <CAKMK7uGA-ENZRQySGVrDkBy7dTOigkKpwpTn63rfGM+UAGvPZA@mail.gmail.com>
2013-12-11 14:25 ` Daniel Vetter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1383990548-30737-4-git-send-email-shobhit.kumar@intel.com \
--to=shobhit.kumar@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=jani.nikula@intel.com \
--cc=vijayakumar.balakrishnan@intel.com \
--cc=yogesh.mohan.marimuthu@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox