[PATCH v3 0/9] Introduce J742S2 SoC and EVM

[PATCH v3 0/9] Introduce J742S2 SoC and EVM

[Manorit Chawdhry]

The series adds support for J742S2 family of SoCs. Also adds J742S2 EVM
Support and re-uses most of the stuff from the superset device J784s4.

It initially cleans up the J784s4 SoC files so that they can be
re-usable for j742s2 by introducing -common files. Next it cleans up the
EVM files for j784s4 in a similar way and then goes about adding the
support for j742s2.

Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
Changes in v3:
* Nishanth
- Update copyright string
- Add TRM link in SoC file.
- Refactor to split out common soc support between j742s2 and j784s4

- Add DTC_FLAGS as well for j742s2
- Link to v2: https://lore.kernel.org/r/20240730-b4-upstream-j742s2-v2-0-6aedf892156c@ti.com

---
Manorit Chawdhry (9):
      arm64: dts: ti: Move j784s4-{} include files to j784s4-j742s2-{}-common.dtsi
      arm64: dts: ti: Move k3-j784s4.dtsi to k3-j784s4-j742s2-common.dtsi
      arm64: dts: ti: Split k3-j784s4-j742s2-common.dtsi
      arm64: dts: ti: Split k3-j784s4-j742s2-main-common.dtsi
      arm64: dts: ti: Move k3-j784s4-evm.dts to k3-j784s4-j742s2-evm-common.dtsi
      arm64: dts: ti: Split k3-j784s4-j742s2-evm-common.dtsi
      dt-bindings: arm: ti: Add bindings for J742S2 SoCs and Boards
      arm64: dts: ti: Introduce J742S2 SoC family
      arm64: dts: ti: Add support for J742S2 EVM board

 Documentation/devicetree/bindings/arm/ti/k3.yaml   |    6 +
 arch/arm64/boot/dts/ti/Makefile                    |    4 +
 arch/arm64/boot/dts/ti/k3-j742s2-evm.dts           |   26 +
 arch/arm64/boot/dts/ti/k3-j742s2-main.dtsi         |   45 +
 arch/arm64/boot/dts/ti/k3-j742s2.dtsi              |   98 +
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts           | 1422 +---------
 .../arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi |  150 ++
 .../boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi   | 1436 ++++++++++
 .../boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi  | 2772 ++++++++++++++++++++
 ...tsi => k3-j784s4-j742s2-mcu-wakeup-common.dtsi} |    2 +-
 ...l.dtsi => k3-j784s4-j742s2-thermal-common.dtsi} |    0
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi         | 2764 -------------------
 arch/arm64/boot/dts/ti/k3-j784s4.dtsi              |  135 +-
 13 files changed, 4540 insertions(+), 4320 deletions(-)
---
base-commit: cd19ac2f903276b820f5d0d89de0c896c27036ed
change-id: 20240620-b4-upstream-j742s2-7ba652091550

Best regards,
-- 
Manorit Chawdhry <m-chawdhry@ti.com>

[PATCH v3 1/9] arm64: dts: ti: Move j784s4-{} include files to j784s4-j742s2-{}-common.dtsi

[Manorit Chawdhry]

J784S4 shares a lot of things with J742s2. Move the files to common so
that the split between j784s4 and j742s2 can be done at a later point.

Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
 .../ti/{k3-j784s4-main.dtsi => k3-j784s4-j742s2-main-common.dtsi}   | 2 +-
 ...84s4-mcu-wakeup.dtsi => k3-j784s4-j742s2-mcu-wakeup-common.dtsi} | 2 +-
 ...{k3-j784s4-thermal.dtsi => k3-j784s4-j742s2-thermal-common.dtsi} | 0
 arch/arm64/boot/dts/ti/k3-j784s4.dtsi                               | 6 +++---
 4 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
similarity index 99%
rename from arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
rename to arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
index f170f80f00c1..17abd0f1560a 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only OR MIT
 /*
- * Device Tree Source for J784S4 SoC Family Main Domain peripherals
+ * Device Tree Source for J784S4 and J742S2 SoC Family Main Domain peripherals
  *
  * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
  */
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-mcu-wakeup-common.dtsi
similarity index 99%
rename from arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
rename to arch/arm64/boot/dts/ti/k3-j784s4-j742s2-mcu-wakeup-common.dtsi
index f3a6ed1c979d..346623fa2ee9 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-mcu-wakeup-common.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only OR MIT
 /*
- * Device Tree Source for J784S4 SoC Family MCU/WAKEUP Domain peripherals
+ * Device Tree Source for J784S4 and J742S2 SoC Family MCU/WAKEUP Domain peripherals
  *
  * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
  */
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-thermal-common.dtsi
similarity index 100%
rename from arch/arm64/boot/dts/ti/k3-j784s4-thermal.dtsi
rename to arch/arm64/boot/dts/ti/k3-j784s4-j742s2-thermal-common.dtsi
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
index 73cc3c1fec08..76e43ee44496 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
@@ -296,10 +296,10 @@ cbass_mcu_wakeup: bus@28380000 {
 	};
 
 	thermal_zones: thermal-zones {
-		#include "k3-j784s4-thermal.dtsi"
+		#include "k3-j784s4-j742s2-thermal-common.dtsi"
 	};
 };
 
 /* Now include peripherals from each bus segment */
-#include "k3-j784s4-main.dtsi"
-#include "k3-j784s4-mcu-wakeup.dtsi"
+#include "k3-j784s4-j742s2-main-common.dtsi"
+#include "k3-j784s4-j742s2-mcu-wakeup-common.dtsi"

-- 
2.45.1

[PATCH v3 2/9] arm64: dts: ti: Move k3-j784s4.dtsi to k3-j784s4-j742s2-common.dtsi

[Manorit Chawdhry]

This is to introduce j742s2 support later, things from here will be
moved to appropriate location.

File k3-j784s4.dtsi is not exactly removed as the EVM files are
dependent on that. Hence to keep the compatibility, after moving;
k3-j784s4.dtsi is including k3-j784s4-j742s2-common.dtsi

Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
 .../arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi | 305 +++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j784s4.dtsi              | 295 +-------------------
 2 files changed, 306 insertions(+), 294 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi
new file mode 100644
index 000000000000..76e43ee44496
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi
@@ -0,0 +1,305 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Device Tree Source for J784S4 SoC Family
+ *
+ * TRM (SPRUJ43 JULY 2022): https://www.ti.com/lit/zip/spruj52
+ *
+ * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+#include "k3-pinctrl.h"
+
+/ {
+	model = "Texas Instruments K3 J784S4 SoC";
+	compatible = "ti,j784s4";
+	interrupt-parent = <&gic500>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu-map {
+			cluster0: cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+
+			cluster1: cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+
+				core1 {
+					cpu = <&cpu5>;
+				};
+
+				core2 {
+					cpu = <&cpu6>;
+				};
+
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a72";
+			reg = <0x000>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a72";
+			reg = <0x001>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a72";
+			reg = <0x002>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a72";
+			reg = <0x003>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu4: cpu@100 {
+			compatible = "arm,cortex-a72";
+			reg = <0x100>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_1>;
+		};
+
+		cpu5: cpu@101 {
+			compatible = "arm,cortex-a72";
+			reg = <0x101>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_1>;
+		};
+
+		cpu6: cpu@102 {
+			compatible = "arm,cortex-a72";
+			reg = <0x102>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_1>;
+		};
+
+		cpu7: cpu@103 {
+			compatible = "arm,cortex-a72";
+			reg = <0x103>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_1>;
+		};
+	};
+
+	L2_0: l2-cache0 {
+		compatible = "cache";
+		cache-level = <2>;
+		cache-unified;
+		cache-size = <0x200000>;
+		cache-line-size = <64>;
+		cache-sets = <1024>;
+		next-level-cache = <&msmc_l3>;
+	};
+
+	L2_1: l2-cache1 {
+		compatible = "cache";
+		cache-level = <2>;
+		cache-unified;
+		cache-size = <0x200000>;
+		cache-line-size = <64>;
+		cache-sets = <1024>;
+		next-level-cache = <&msmc_l3>;
+	};
+
+	msmc_l3: l3-cache0 {
+		compatible = "cache";
+		cache-level = <3>;
+		cache-unified;
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+
+		psci: psci {
+			compatible = "arm,psci-1.0";
+			method = "smc";
+		};
+	};
+
+	a72_timer0: timer-cl0-cpu0 {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* cntpsirq */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* cntpnsirq */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* cntvirq */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* cnthpirq */
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a72-pmu";
+		/* Recommendation from GIC500 TRM Table A.3 */
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	cbass_main: bus@100000 {
+		bootph-all;
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0x00 0x00100000 0x00 0x00100000 0x00 0x00020000>, /* ctrl mmr */
+			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00031100>, /* GPIO */
+			 <0x00 0x00700000 0x00 0x00700000 0x00 0x00001000>, /* ESM */
+			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0d000000>, /* Most peripherals */
+			 <0x00 0x04210000 0x00 0x04210000 0x00 0x00010000>, /* VPU0 */
+			 <0x00 0x04220000 0x00 0x04220000 0x00 0x00010000>, /* VPU1 */
+			 <0x00 0x0d000000 0x00 0x0d000000 0x00 0x00800000>, /* PCIe0 Core*/
+			 <0x00 0x0d800000 0x00 0x0d800000 0x00 0x00800000>, /* PCIe1 Core*/
+			 <0x00 0x0e000000 0x00 0x0e000000 0x00 0x00800000>, /* PCIe2 Core*/
+			 <0x00 0x0e800000 0x00 0x0e800000 0x00 0x00800000>, /* PCIe3 Core*/
+			 <0x00 0x10000000 0x00 0x10000000 0x00 0x08000000>, /* PCIe0 DAT0 */
+			 <0x00 0x18000000 0x00 0x18000000 0x00 0x08000000>, /* PCIe1 DAT0 */
+			 <0x00 0x64800000 0x00 0x64800000 0x00 0x0070c000>, /* C71_1 */
+			 <0x00 0x65800000 0x00 0x65800000 0x00 0x0070c000>, /* C71_2 */
+			 <0x00 0x66800000 0x00 0x66800000 0x00 0x0070c000>, /* C71_3 */
+			 <0x00 0x67800000 0x00 0x67800000 0x00 0x0070c000>, /* C71_4 */
+			 <0x00 0x6f000000 0x00 0x6f000000 0x00 0x00310000>, /* A72 PERIPHBASE */
+			 <0x00 0x70000000 0x00 0x70000000 0x00 0x00400000>, /* MSMC RAM */
+			 <0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>, /* MAIN NAVSS */
+			 <0x40 0x00000000 0x40 0x00000000 0x01 0x00000000>, /* PCIe0 DAT1 */
+			 <0x41 0x00000000 0x41 0x00000000 0x01 0x00000000>, /* PCIe1 DAT1 */
+			 <0x42 0x00000000 0x42 0x00000000 0x01 0x00000000>, /* PCIe2 DAT1 */
+			 <0x43 0x00000000 0x43 0x00000000 0x01 0x00000000>, /* PCIe3 DAT1 */
+			 <0x44 0x00000000 0x44 0x00000000 0x00 0x08000000>, /* PCIe2 DAT0 */
+			 <0x44 0x10000000 0x44 0x10000000 0x00 0x08000000>, /* PCIe3 DAT0 */
+			 <0x4e 0x20000000 0x4e 0x20000000 0x00 0x00080000>, /* GPU */
+
+			 /* MCUSS_WKUP Range */
+			 <0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>,
+			 <0x00 0x40200000 0x00 0x40200000 0x00 0x00998400>,
+			 <0x00 0x40f00000 0x00 0x40f00000 0x00 0x00020000>,
+			 <0x00 0x41000000 0x00 0x41000000 0x00 0x00020000>,
+			 <0x00 0x41400000 0x00 0x41400000 0x00 0x00020000>,
+			 <0x00 0x41c00000 0x00 0x41c00000 0x00 0x00100000>,
+			 <0x00 0x42040000 0x00 0x42040000 0x00 0x03ac2400>,
+			 <0x00 0x45100000 0x00 0x45100000 0x00 0x00c24000>,
+			 <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>,
+			 <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>,
+			 <0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>,
+			 <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>,
+			 <0x07 0x00000000 0x07 0x00000000 0x01 0x00000000>;
+
+		cbass_mcu_wakeup: bus@28380000 {
+			bootph-all;
+			compatible = "simple-bus";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>, /* MCU NAVSS*/
+				 <0x00 0x40200000 0x00 0x40200000 0x00 0x00998400>, /* First peripheral window */
+				 <0x00 0x40f00000 0x00 0x40f00000 0x00 0x00020000>, /* CTRL_MMR0 */
+				 <0x00 0x41000000 0x00 0x41000000 0x00 0x00020000>, /* MCU R5F Core0 */
+				 <0x00 0x41400000 0x00 0x41400000 0x00 0x00020000>, /* MCU R5F Core1 */
+				 <0x00 0x41c00000 0x00 0x41c00000 0x00 0x00100000>, /* MCU SRAM */
+				 <0x00 0x42040000 0x00 0x42040000 0x00 0x03ac2400>, /* WKUP peripheral window */
+				 <0x00 0x45100000 0x00 0x45100000 0x00 0x00c24000>, /* MMRs, remaining NAVSS */
+				 <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>, /* CPSW */
+				 <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>, /* OSPI register space */
+				 <0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>, /* FSS OSPI0/1 data region 0 */
+				 <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>, /* FSS OSPI0 data region 3 */
+				 <0x07 0x00000000 0x07 0x00000000 0x01 0x00000000>; /* FSS OSPI1 data region 3*/
+		};
+	};
+
+	thermal_zones: thermal-zones {
+		#include "k3-j784s4-j742s2-thermal-common.dtsi"
+	};
+};
+
+/* Now include peripherals from each bus segment */
+#include "k3-j784s4-j742s2-main-common.dtsi"
+#include "k3-j784s4-j742s2-mcu-wakeup-common.dtsi"
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
index 76e43ee44496..46cff5ed3730 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
@@ -8,298 +8,5 @@
  *
  */
 
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/soc/ti,sci_pm_domain.h>
+#include "k3-j784s4-j742s2-common.dtsi"
 
-#include "k3-pinctrl.h"
-
-/ {
-	model = "Texas Instruments K3 J784S4 SoC";
-	compatible = "ti,j784s4";
-	interrupt-parent = <&gic500>;
-	#address-cells = <2>;
-	#size-cells = <2>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		cpu-map {
-			cluster0: cluster0 {
-				core0 {
-					cpu = <&cpu0>;
-				};
-
-				core1 {
-					cpu = <&cpu1>;
-				};
-
-				core2 {
-					cpu = <&cpu2>;
-				};
-
-				core3 {
-					cpu = <&cpu3>;
-				};
-			};
-
-			cluster1: cluster1 {
-				core0 {
-					cpu = <&cpu4>;
-				};
-
-				core1 {
-					cpu = <&cpu5>;
-				};
-
-				core2 {
-					cpu = <&cpu6>;
-				};
-
-				core3 {
-					cpu = <&cpu7>;
-				};
-			};
-		};
-
-		cpu0: cpu@0 {
-			compatible = "arm,cortex-a72";
-			reg = <0x000>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_0>;
-		};
-
-		cpu1: cpu@1 {
-			compatible = "arm,cortex-a72";
-			reg = <0x001>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_0>;
-		};
-
-		cpu2: cpu@2 {
-			compatible = "arm,cortex-a72";
-			reg = <0x002>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_0>;
-		};
-
-		cpu3: cpu@3 {
-			compatible = "arm,cortex-a72";
-			reg = <0x003>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_0>;
-		};
-
-		cpu4: cpu@100 {
-			compatible = "arm,cortex-a72";
-			reg = <0x100>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_1>;
-		};
-
-		cpu5: cpu@101 {
-			compatible = "arm,cortex-a72";
-			reg = <0x101>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_1>;
-		};
-
-		cpu6: cpu@102 {
-			compatible = "arm,cortex-a72";
-			reg = <0x102>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_1>;
-		};
-
-		cpu7: cpu@103 {
-			compatible = "arm,cortex-a72";
-			reg = <0x103>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_1>;
-		};
-	};
-
-	L2_0: l2-cache0 {
-		compatible = "cache";
-		cache-level = <2>;
-		cache-unified;
-		cache-size = <0x200000>;
-		cache-line-size = <64>;
-		cache-sets = <1024>;
-		next-level-cache = <&msmc_l3>;
-	};
-
-	L2_1: l2-cache1 {
-		compatible = "cache";
-		cache-level = <2>;
-		cache-unified;
-		cache-size = <0x200000>;
-		cache-line-size = <64>;
-		cache-sets = <1024>;
-		next-level-cache = <&msmc_l3>;
-	};
-
-	msmc_l3: l3-cache0 {
-		compatible = "cache";
-		cache-level = <3>;
-		cache-unified;
-	};
-
-	firmware {
-		optee {
-			compatible = "linaro,optee-tz";
-			method = "smc";
-		};
-
-		psci: psci {
-			compatible = "arm,psci-1.0";
-			method = "smc";
-		};
-	};
-
-	a72_timer0: timer-cl0-cpu0 {
-		compatible = "arm,armv8-timer";
-		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* cntpsirq */
-			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* cntpnsirq */
-			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* cntvirq */
-			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* cnthpirq */
-	};
-
-	pmu: pmu {
-		compatible = "arm,cortex-a72-pmu";
-		/* Recommendation from GIC500 TRM Table A.3 */
-		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
-	};
-
-	cbass_main: bus@100000 {
-		bootph-all;
-		compatible = "simple-bus";
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges = <0x00 0x00100000 0x00 0x00100000 0x00 0x00020000>, /* ctrl mmr */
-			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00031100>, /* GPIO */
-			 <0x00 0x00700000 0x00 0x00700000 0x00 0x00001000>, /* ESM */
-			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0d000000>, /* Most peripherals */
-			 <0x00 0x04210000 0x00 0x04210000 0x00 0x00010000>, /* VPU0 */
-			 <0x00 0x04220000 0x00 0x04220000 0x00 0x00010000>, /* VPU1 */
-			 <0x00 0x0d000000 0x00 0x0d000000 0x00 0x00800000>, /* PCIe0 Core*/
-			 <0x00 0x0d800000 0x00 0x0d800000 0x00 0x00800000>, /* PCIe1 Core*/
-			 <0x00 0x0e000000 0x00 0x0e000000 0x00 0x00800000>, /* PCIe2 Core*/
-			 <0x00 0x0e800000 0x00 0x0e800000 0x00 0x00800000>, /* PCIe3 Core*/
-			 <0x00 0x10000000 0x00 0x10000000 0x00 0x08000000>, /* PCIe0 DAT0 */
-			 <0x00 0x18000000 0x00 0x18000000 0x00 0x08000000>, /* PCIe1 DAT0 */
-			 <0x00 0x64800000 0x00 0x64800000 0x00 0x0070c000>, /* C71_1 */
-			 <0x00 0x65800000 0x00 0x65800000 0x00 0x0070c000>, /* C71_2 */
-			 <0x00 0x66800000 0x00 0x66800000 0x00 0x0070c000>, /* C71_3 */
-			 <0x00 0x67800000 0x00 0x67800000 0x00 0x0070c000>, /* C71_4 */
-			 <0x00 0x6f000000 0x00 0x6f000000 0x00 0x00310000>, /* A72 PERIPHBASE */
-			 <0x00 0x70000000 0x00 0x70000000 0x00 0x00400000>, /* MSMC RAM */
-			 <0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>, /* MAIN NAVSS */
-			 <0x40 0x00000000 0x40 0x00000000 0x01 0x00000000>, /* PCIe0 DAT1 */
-			 <0x41 0x00000000 0x41 0x00000000 0x01 0x00000000>, /* PCIe1 DAT1 */
-			 <0x42 0x00000000 0x42 0x00000000 0x01 0x00000000>, /* PCIe2 DAT1 */
-			 <0x43 0x00000000 0x43 0x00000000 0x01 0x00000000>, /* PCIe3 DAT1 */
-			 <0x44 0x00000000 0x44 0x00000000 0x00 0x08000000>, /* PCIe2 DAT0 */
-			 <0x44 0x10000000 0x44 0x10000000 0x00 0x08000000>, /* PCIe3 DAT0 */
-			 <0x4e 0x20000000 0x4e 0x20000000 0x00 0x00080000>, /* GPU */
-
-			 /* MCUSS_WKUP Range */
-			 <0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>,
-			 <0x00 0x40200000 0x00 0x40200000 0x00 0x00998400>,
-			 <0x00 0x40f00000 0x00 0x40f00000 0x00 0x00020000>,
-			 <0x00 0x41000000 0x00 0x41000000 0x00 0x00020000>,
-			 <0x00 0x41400000 0x00 0x41400000 0x00 0x00020000>,
-			 <0x00 0x41c00000 0x00 0x41c00000 0x00 0x00100000>,
-			 <0x00 0x42040000 0x00 0x42040000 0x00 0x03ac2400>,
-			 <0x00 0x45100000 0x00 0x45100000 0x00 0x00c24000>,
-			 <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>,
-			 <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>,
-			 <0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>,
-			 <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>,
-			 <0x07 0x00000000 0x07 0x00000000 0x01 0x00000000>;
-
-		cbass_mcu_wakeup: bus@28380000 {
-			bootph-all;
-			compatible = "simple-bus";
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges = <0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>, /* MCU NAVSS*/
-				 <0x00 0x40200000 0x00 0x40200000 0x00 0x00998400>, /* First peripheral window */
-				 <0x00 0x40f00000 0x00 0x40f00000 0x00 0x00020000>, /* CTRL_MMR0 */
-				 <0x00 0x41000000 0x00 0x41000000 0x00 0x00020000>, /* MCU R5F Core0 */
-				 <0x00 0x41400000 0x00 0x41400000 0x00 0x00020000>, /* MCU R5F Core1 */
-				 <0x00 0x41c00000 0x00 0x41c00000 0x00 0x00100000>, /* MCU SRAM */
-				 <0x00 0x42040000 0x00 0x42040000 0x00 0x03ac2400>, /* WKUP peripheral window */
-				 <0x00 0x45100000 0x00 0x45100000 0x00 0x00c24000>, /* MMRs, remaining NAVSS */
-				 <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>, /* CPSW */
-				 <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>, /* OSPI register space */
-				 <0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>, /* FSS OSPI0/1 data region 0 */
-				 <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>, /* FSS OSPI0 data region 3 */
-				 <0x07 0x00000000 0x07 0x00000000 0x01 0x00000000>; /* FSS OSPI1 data region 3*/
-		};
-	};
-
-	thermal_zones: thermal-zones {
-		#include "k3-j784s4-j742s2-thermal-common.dtsi"
-	};
-};
-
-/* Now include peripherals from each bus segment */
-#include "k3-j784s4-j742s2-main-common.dtsi"
-#include "k3-j784s4-j742s2-mcu-wakeup-common.dtsi"

-- 
2.45.1

[PATCH v3 3/9] arm64: dts: ti: Split k3-j784s4-j742s2-common.dtsi

[Manorit Chawdhry]

k3-j784s4-j742s2-common.dtsi will be included in k3-j742s2.dtsi at a
later point so move j784s4 related stuff to k3-j784s4.dtsi

Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
 .../arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi | 156 --------------------
 arch/arm64/boot/dts/ti/k3-j784s4.dtsi              | 158 +++++++++++++++++++++
 2 files changed, 158 insertions(+), 156 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi
index 76e43ee44496..958054ab1018 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi
@@ -15,166 +15,10 @@
 #include "k3-pinctrl.h"
 
 / {
-	model = "Texas Instruments K3 J784S4 SoC";
-	compatible = "ti,j784s4";
 	interrupt-parent = <&gic500>;
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		cpu-map {
-			cluster0: cluster0 {
-				core0 {
-					cpu = <&cpu0>;
-				};
-
-				core1 {
-					cpu = <&cpu1>;
-				};
-
-				core2 {
-					cpu = <&cpu2>;
-				};
-
-				core3 {
-					cpu = <&cpu3>;
-				};
-			};
-
-			cluster1: cluster1 {
-				core0 {
-					cpu = <&cpu4>;
-				};
-
-				core1 {
-					cpu = <&cpu5>;
-				};
-
-				core2 {
-					cpu = <&cpu6>;
-				};
-
-				core3 {
-					cpu = <&cpu7>;
-				};
-			};
-		};
-
-		cpu0: cpu@0 {
-			compatible = "arm,cortex-a72";
-			reg = <0x000>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_0>;
-		};
-
-		cpu1: cpu@1 {
-			compatible = "arm,cortex-a72";
-			reg = <0x001>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_0>;
-		};
-
-		cpu2: cpu@2 {
-			compatible = "arm,cortex-a72";
-			reg = <0x002>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_0>;
-		};
-
-		cpu3: cpu@3 {
-			compatible = "arm,cortex-a72";
-			reg = <0x003>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_0>;
-		};
-
-		cpu4: cpu@100 {
-			compatible = "arm,cortex-a72";
-			reg = <0x100>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_1>;
-		};
-
-		cpu5: cpu@101 {
-			compatible = "arm,cortex-a72";
-			reg = <0x101>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_1>;
-		};
-
-		cpu6: cpu@102 {
-			compatible = "arm,cortex-a72";
-			reg = <0x102>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_1>;
-		};
-
-		cpu7: cpu@103 {
-			compatible = "arm,cortex-a72";
-			reg = <0x103>;
-			device_type = "cpu";
-			enable-method = "psci";
-			i-cache-size = <0xc000>;
-			i-cache-line-size = <64>;
-			i-cache-sets = <256>;
-			d-cache-size = <0x8000>;
-			d-cache-line-size = <64>;
-			d-cache-sets = <256>;
-			next-level-cache = <&L2_1>;
-		};
-	};
-
 	L2_0: l2-cache0 {
 		compatible = "cache";
 		cache-level = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
index 46cff5ed3730..16ade4fd9cbd 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
@@ -10,3 +10,161 @@
 
 #include "k3-j784s4-j742s2-common.dtsi"
 
+/ {
+	model = "Texas Instruments K3 J784S4 SoC";
+	compatible = "ti,j784s4";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu-map {
+			cluster0: cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+
+			cluster1: cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+
+				core1 {
+					cpu = <&cpu5>;
+				};
+
+				core2 {
+					cpu = <&cpu6>;
+				};
+
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a72";
+			reg = <0x000>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a72";
+			reg = <0x001>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a72";
+			reg = <0x002>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a72";
+			reg = <0x003>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu4: cpu@100 {
+			compatible = "arm,cortex-a72";
+			reg = <0x100>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_1>;
+		};
+
+		cpu5: cpu@101 {
+			compatible = "arm,cortex-a72";
+			reg = <0x101>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_1>;
+		};
+
+		cpu6: cpu@102 {
+			compatible = "arm,cortex-a72";
+			reg = <0x102>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_1>;
+		};
+
+		cpu7: cpu@103 {
+			compatible = "arm,cortex-a72";
+			reg = <0x103>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_1>;
+		};
+	};
+};

-- 
2.45.1

[PATCH v3 4/9] arm64: dts: ti: Split k3-j784s4-j742s2-main-common.dtsi

[Manorit Chawdhry]

k3-j784s4-j742s2-main-common.dtsi will be included in k3-j742s2-main.dtsi at a
later point so move j784s4 related stuff to k3-j784s4-main.dtsi

Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
 .../boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi   | 13 -------------
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi          | 21 +++++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j784s4.dtsi               |  2 ++
 3 files changed, 23 insertions(+), 13 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
index 17abd0f1560a..91352b1f63d2 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
@@ -2405,19 +2405,6 @@ c71_2: dsp@66800000 {
 		status = "disabled";
 	};
 
-	c71_3: dsp@67800000 {
-		compatible = "ti,j721s2-c71-dsp";
-		reg = <0x00 0x67800000 0x00 0x00080000>,
-		      <0x00 0x67e00000 0x00 0x0000c000>;
-		reg-names = "l2sram", "l1dram";
-		ti,sci = <&sms>;
-		ti,sci-dev-id = <40>;
-		ti,sci-proc-ids = <0x33 0xff>;
-		resets = <&k3_reset 40 1>;
-		firmware-name = "j784s4-c71_3-fw";
-		status = "disabled";
-	};
-
 	main_esm: esm@700000 {
 		compatible = "ti,j721e-esm";
 		reg = <0x00 0x700000 0x00 0x1000>;
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
new file mode 100644
index 000000000000..2ea470d1206d
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Device Tree Source for J784S4 SoC Family Main Domain peripherals
+ *
+ * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&cbass_main {
+	c71_3: dsp@67800000 {
+		compatible = "ti,j721s2-c71-dsp";
+		reg = <0x00 0x67800000 0x00 0x00080000>,
+		      <0x00 0x67e00000 0x00 0x0000c000>;
+		reg-names = "l2sram", "l1dram";
+		ti,sci = <&sms>;
+		ti,sci-dev-id = <40>;
+		ti,sci-proc-ids = <0x33 0xff>;
+		resets = <&k3_reset 40 1>;
+		firmware-name = "j784s4-c71_3-fw";
+		status = "disabled";
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
index 16ade4fd9cbd..f5afa32157cb 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
@@ -168,3 +168,5 @@ cpu7: cpu@103 {
 		};
 	};
 };
+
+#include "k3-j784s4-main.dtsi"

-- 
2.45.1

Re: [PATCH v3 4/9] arm64: dts: ti: Split k3-j784s4-j742s2-main-common.dtsi

[Nishanth Menon]

On 22:40-20240731, Manorit Chawdhry wrote:
> k3-j784s4-j742s2-main-common.dtsi will be included in k3-j742s2-main.dtsi at a
> later point so move j784s4 related stuff to k3-j784s4-main.dtsi

Reword as suggested for the evm.

> 
> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
> ---
[...]
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> new file mode 100644
> index 000000000000..2ea470d1206d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> @@ -0,0 +1,21 @@
> +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> +/*
> + * Device Tree Source for J784S4 SoC Family Main Domain peripherals
> + *
> + * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +&cbass_main {
> +	c71_3: dsp@67800000 {
> +		compatible = "ti,j721s2-c71-dsp";
> +		reg = <0x00 0x67800000 0x00 0x00080000>,
> +		      <0x00 0x67e00000 0x00 0x0000c000>;
> +		reg-names = "l2sram", "l1dram";
> +		ti,sci = <&sms>;
> +		ti,sci-dev-id = <40>;
> +		ti,sci-proc-ids = <0x33 0xff>;
^^ vendor specific properties

> +		resets = <&k3_reset 40 1>;
> +		firmware-name = "j784s4-c71_3-fw";
^^ common properties
> +		status = "disabled";
> +	};
> +};

Since we are refactoring, we can use this opportunity to cleanup a bit
when the node is getting introduced.

> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
> index 16ade4fd9cbd..f5afa32157cb 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
> @@ -168,3 +168,5 @@ cpu7: cpu@103 {
>  		};
>  	};
>  };
> +
> +#include "k3-j784s4-main.dtsi"
> 
> -- 
> 2.45.1
> 

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH v3 4/9] arm64: dts: ti: Split k3-j784s4-j742s2-main-common.dtsi

[Nishanth Menon]

On 22:40-20240731, Manorit Chawdhry wrote:
> k3-j784s4-j742s2-main-common.dtsi will be included in k3-j742s2-main.dtsi at a
> later point so move j784s4 related stuff to k3-j784s4-main.dtsi
> 
> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
> ---
>  .../boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi   | 13 -------------
>  arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi          | 21 +++++++++++++++++++++
>  arch/arm64/boot/dts/ti/k3-j784s4.dtsi               |  2 ++
>  3 files changed, 23 insertions(+), 13 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
> index 17abd0f1560a..91352b1f63d2 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
> @@ -2405,19 +2405,6 @@ c71_2: dsp@66800000 {
>  		status = "disabled";
>  	};
>  
> -	c71_3: dsp@67800000 {
> -		compatible = "ti,j721s2-c71-dsp";
> -		reg = <0x00 0x67800000 0x00 0x00080000>,
> -		      <0x00 0x67e00000 0x00 0x0000c000>;
> -		reg-names = "l2sram", "l1dram";
> -		ti,sci = <&sms>;
> -		ti,sci-dev-id = <40>;
> -		ti,sci-proc-ids = <0x33 0xff>;
> -		resets = <&k3_reset 40 1>;
> -		firmware-name = "j784s4-c71_3-fw";
> -		status = "disabled";
> -	};
> -

This patch can be squashed in.

>  	main_esm: esm@700000 {
>  		compatible = "ti,j721e-esm";
>  		reg = <0x00 0x700000 0x00 0x1000>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> new file mode 100644
> index 000000000000..2ea470d1206d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> @@ -0,0 +1,21 @@
> +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> +/*
> + * Device Tree Source for J784S4 SoC Family Main Domain peripherals
> + *
> + * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +&cbass_main {
> +	c71_3: dsp@67800000 {
> +		compatible = "ti,j721s2-c71-dsp";
> +		reg = <0x00 0x67800000 0x00 0x00080000>,
> +		      <0x00 0x67e00000 0x00 0x0000c000>;
> +		reg-names = "l2sram", "l1dram";
> +		ti,sci = <&sms>;
> +		ti,sci-dev-id = <40>;
> +		ti,sci-proc-ids = <0x33 0xff>;
> +		resets = <&k3_reset 40 1>;
> +		firmware-name = "j784s4-c71_3-fw";
> +		status = "disabled";
> +	};
> +};

I am looking at https://www.ti.com/lit/ug/spruje3/spruje3.pdf (page 26),
Device Comparison:

CPSW/Serdes, PCIE is also different? Was that missed?

> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
> index 16ade4fd9cbd..f5afa32157cb 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4.dtsi
> @@ -168,3 +168,5 @@ cpu7: cpu@103 {
>  		};
>  	};
>  };
> +
> +#include "k3-j784s4-main.dtsi"
> 
> -- 
> 2.45.1
> 

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH v3 4/9] arm64: dts: ti: Split k3-j784s4-j742s2-main-common.dtsi

[Manorit Chawdhry]

Hi Nishanth,

> > diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> > new file mode 100644
> > index 000000000000..2ea470d1206d
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> > @@ -0,0 +1,21 @@
> > +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> > +/*
> > + * Device Tree Source for J784S4 SoC Family Main Domain peripherals
> > + *
> > + * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
> > + */
> > +
> > +&cbass_main {
> > +	c71_3: dsp@67800000 {
> > +		compatible = "ti,j721s2-c71-dsp";
> > +		reg = <0x00 0x67800000 0x00 0x00080000>,
> > +		      <0x00 0x67e00000 0x00 0x0000c000>;
> > +		reg-names = "l2sram", "l1dram";
> > +		ti,sci = <&sms>;
> > +		ti,sci-dev-id = <40>;
> > +		ti,sci-proc-ids = <0x33 0xff>;
> > +		resets = <&k3_reset 40 1>;
> > +		firmware-name = "j784s4-c71_3-fw";
> > +		status = "disabled";
> > +	};
> > +};
> 
> I am looking at https://www.ti.com/lit/ug/spruje3/spruje3.pdf (page 26),
> Device Comparison:
> 
> CPSW/Serdes, PCIE is also different? Was that missed?

I had talked to Siddharth in the past regarding that and he had
mentioned that no change would be required with the previous patchsets
that I had shared, adding him to the thread 

Regards,
Manorit

Re: [PATCH v3 4/9] arm64: dts: ti: Split k3-j784s4-j742s2-main-common.dtsi

[Siddharth Vadapalli]

On Thu, Aug 08, 2024 at 10:22:27AM +0530, Manorit Chawdhry wrote:
> Hi Nishanth,
> 
> > > diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> > > new file mode 100644
> > > index 000000000000..2ea470d1206d
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> > > @@ -0,0 +1,21 @@
> > > +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> > > +/*
> > > + * Device Tree Source for J784S4 SoC Family Main Domain peripherals
> > > + *
> > > + * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
> > > + */
> > > +
> > > +&cbass_main {
> > > +	c71_3: dsp@67800000 {
> > > +		compatible = "ti,j721s2-c71-dsp";
> > > +		reg = <0x00 0x67800000 0x00 0x00080000>,
> > > +		      <0x00 0x67e00000 0x00 0x0000c000>;
> > > +		reg-names = "l2sram", "l1dram";
> > > +		ti,sci = <&sms>;
> > > +		ti,sci-dev-id = <40>;
> > > +		ti,sci-proc-ids = <0x33 0xff>;
> > > +		resets = <&k3_reset 40 1>;
> > > +		firmware-name = "j784s4-c71_3-fw";
> > > +		status = "disabled";
> > > +	};
> > > +};
> > 
> > I am looking at https://www.ti.com/lit/ug/spruje3/spruje3.pdf (page 26),
> > Device Comparison:
> > 
> > CPSW/Serdes, PCIE is also different? Was that missed?
> 
> I had talked to Siddharth in the past regarding that and he had
> mentioned that no change would be required with the previous patchsets
> that I had shared, adding him to the thread 

Manorit,

Since J784S4-EVM enables only PCIe0 and PCIe1 which matches the
instances enabled/supported on J742S2-EVM, I had informed you that for
the purpose of validation, no changes will be required w.r.t. PCIe, if
k3-j742s2-evm.dts is including k3-j784s4-evm.dts. However, considering
that the device-tree should describe the hardware, when upstreaming the
device-tree for J742S2, PCIe2 and PCIe3 should be deleted
(if k3-j784s4-evm.dts is included by k3-j742s2-evm.dts) OR dropped
(if there is a "common" file that is used to describe the peripherals
common to J742S2 and J784S4 as done in the current series).

Also, SERDES2 is not present on J742S2 SoC while J784S4 has SERDES0,
SERDES1, SERDES2 and SERDES4. There is no difference w.r.t. CPSW9G in
terms of the CPSW9G instance itself, but the difference is that CPSW9G
cannot use SERDES2. So CPSW9G can only be used with SERDES4 on J742S2
SoC, but J742S2-EVM has the SERDES4 lines connected to Display Ports,
due to which CPSW9G is essentially non-functional on J742S2-EVM.

Regards,
Siddharth.

Re: [PATCH v3 4/9] arm64: dts: ti: Split k3-j784s4-j742s2-main-common.dtsi

[Nishanth Menon]

On 10:58-20240808, Siddharth Vadapalli wrote:
> On Thu, Aug 08, 2024 at 10:22:27AM +0530, Manorit Chawdhry wrote:
> > Hi Nishanth,
> > 
> > > > diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> > > > new file mode 100644
> > > > index 000000000000..2ea470d1206d
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> > > > @@ -0,0 +1,21 @@
> > > > +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> > > > +/*
> > > > + * Device Tree Source for J784S4 SoC Family Main Domain peripherals
> > > > + *
> > > > + * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
> > > > + */
> > > > +
> > > > +&cbass_main {
> > > > +	c71_3: dsp@67800000 {
> > > > +		compatible = "ti,j721s2-c71-dsp";
> > > > +		reg = <0x00 0x67800000 0x00 0x00080000>,
> > > > +		      <0x00 0x67e00000 0x00 0x0000c000>;
> > > > +		reg-names = "l2sram", "l1dram";
> > > > +		ti,sci = <&sms>;
> > > > +		ti,sci-dev-id = <40>;
> > > > +		ti,sci-proc-ids = <0x33 0xff>;
> > > > +		resets = <&k3_reset 40 1>;
> > > > +		firmware-name = "j784s4-c71_3-fw";
> > > > +		status = "disabled";
> > > > +	};
> > > > +};
> > > 
> > > I am looking at https://www.ti.com/lit/ug/spruje3/spruje3.pdf (page 26),
> > > Device Comparison:
> > > 
> > > CPSW/Serdes, PCIE is also different? Was that missed?
> > 
> > I had talked to Siddharth in the past regarding that and he had
> > mentioned that no change would be required with the previous patchsets
> > that I had shared, adding him to the thread 
> 
> Manorit,
> 
> Since J784S4-EVM enables only PCIe0 and PCIe1 which matches the
> instances enabled/supported on J742S2-EVM, I had informed you that for
> the purpose of validation, no changes will be required w.r.t. PCIe, if
> k3-j742s2-evm.dts is including k3-j784s4-evm.dts. However, considering
> that the device-tree should describe the hardware, when upstreaming the
> device-tree for J742S2, PCIe2 and PCIe3 should be deleted
> (if k3-j784s4-evm.dts is included by k3-j742s2-evm.dts) OR dropped
> (if there is a "common" file that is used to describe the peripherals
> common to J742S2 and J784S4 as done in the current series).
> 
> Also, SERDES2 is not present on J742S2 SoC while J784S4 has SERDES0,
> SERDES1, SERDES2 and SERDES4. There is no difference w.r.t. CPSW9G in
> terms of the CPSW9G instance itself, but the difference is that CPSW9G
> cannot use SERDES2. So CPSW9G can only be used with SERDES4 on J742S2
> SoC, but J742S2-EVM has the SERDES4 lines connected to Display Ports,
> due to which CPSW9G is essentially non-functional on J742S2-EVM.


Thanks Siddharth. Manorit: Please address the above in the next rev.

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH v3 4/9] arm64: dts: ti: Split k3-j784s4-j742s2-main-common.dtsi

[Manorit Chawdhry]

Hi Nishanth,

On 08:20-20240807, Nishanth Menon wrote:
> On 22:40-20240731, Manorit Chawdhry wrote:
> > k3-j784s4-j742s2-main-common.dtsi will be included in k3-j742s2-main.dtsi at a
> > later point so move j784s4 related stuff to k3-j784s4-main.dtsi
> > 
> > Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
> > ---
> >  .../boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi   | 13 -------------
> >  arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi          | 21 +++++++++++++++++++++
> >  arch/arm64/boot/dts/ti/k3-j784s4.dtsi               |  2 ++
> >  3 files changed, 23 insertions(+), 13 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
> > index 17abd0f1560a..91352b1f63d2 100644
> > --- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
> > @@ -2405,19 +2405,6 @@ c71_2: dsp@66800000 {
> >  		status = "disabled";
> >  	};
> >  
> > -	c71_3: dsp@67800000 {
> > -		compatible = "ti,j721s2-c71-dsp";
> > -		reg = <0x00 0x67800000 0x00 0x00080000>,
> > -		      <0x00 0x67e00000 0x00 0x0000c000>;
> > -		reg-names = "l2sram", "l1dram";
> > -		ti,sci = <&sms>;
> > -		ti,sci-dev-id = <40>;
> > -		ti,sci-proc-ids = <0x33 0xff>;
> > -		resets = <&k3_reset 40 1>;
> > -		firmware-name = "j784s4-c71_3-fw";
> > -		status = "disabled";
> > -	};
> > -
> 
> This patch can be squashed in.
> 

The idea was that we can see what changes are happening and where are
things getting moved and hence had kept the patch like this, would be
easier to review I believe, do you want it squashed right now or should
I be doing it later once you are fine with all the changes and all the
reviews are done?

Regards,
Manorit

Re: [PATCH v3 4/9] arm64: dts: ti: Split k3-j784s4-j742s2-main-common.dtsi

[Nishanth Menon]

On 10:26-20240808, Manorit Chawdhry wrote:
> Hi Nishanth,
> 
> On 08:20-20240807, Nishanth Menon wrote:
> > On 22:40-20240731, Manorit Chawdhry wrote:
> > > k3-j784s4-j742s2-main-common.dtsi will be included in k3-j742s2-main.dtsi at a
> > > later point so move j784s4 related stuff to k3-j784s4-main.dtsi
> > > 
> > > Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
> > > ---
> > >  .../boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi   | 13 -------------
> > >  arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi          | 21 +++++++++++++++++++++
> > >  arch/arm64/boot/dts/ti/k3-j784s4.dtsi               |  2 ++
> > >  3 files changed, 23 insertions(+), 13 deletions(-)
> > > 
> > > diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
> > > index 17abd0f1560a..91352b1f63d2 100644
> > > --- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
> > > +++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi
> > > @@ -2405,19 +2405,6 @@ c71_2: dsp@66800000 {
> > >  		status = "disabled";
> > >  	};
> > >  
> > > -	c71_3: dsp@67800000 {
> > > -		compatible = "ti,j721s2-c71-dsp";
> > > -		reg = <0x00 0x67800000 0x00 0x00080000>,
> > > -		      <0x00 0x67e00000 0x00 0x0000c000>;
> > > -		reg-names = "l2sram", "l1dram";
> > > -		ti,sci = <&sms>;
> > > -		ti,sci-dev-id = <40>;
> > > -		ti,sci-proc-ids = <0x33 0xff>;
> > > -		resets = <&k3_reset 40 1>;
> > > -		firmware-name = "j784s4-c71_3-fw";
> > > -		status = "disabled";
> > > -	};
> > > -
> > 
> > This patch can be squashed in.
> > 
> 
> The idea was that we can see what changes are happening and where are
> things getting moved and hence had kept the patch like this, would be
> easier to review I believe, do you want it squashed right now or should
> I be doing it later once you are fine with all the changes and all the
> reviews are done?
> 

No. Please squash as suggested in my response to your cover-letter for
the next iteration - please use git format-patch -C -M to generate
patches (I understand you have some limitations with using b4) to
make reviews easier to do.

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

[PATCH v3 5/9] arm64: dts: ti: Move k3-j784s4-evm.dts to k3-j784s4-j742s2-evm-common.dtsi

[Manorit Chawdhry]

This is to introduce j742s2 support later, things from here will be
moved to appropriate location.

File k3-j784s4-evm.dts is not exactly removed as the name of DTS files
shouldn't change mid refactor commits. Hence to keep the compatibility,
after moving; k3-j784s4-evm.dts is including
k3-j784s4-j742s2-evm-common.dtsi

Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts           | 1471 +------------------
 .../boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi   | 1477 ++++++++++++++++++++
 2 files changed, 1478 insertions(+), 1470 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index ffa38f41679d..e3730b2bca92 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -5,1473 +5,4 @@
  * EVM Board Schematics: https://www.ti.com/lit/zip/sprr458
  */
 
-/dts-v1/;
-
-#include <dt-bindings/net/ti-dp83867.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "k3-j784s4.dtsi"
-
-/ {
-	compatible = "ti,j784s4-evm", "ti,j784s4";
-	model = "Texas Instruments J784S4 EVM";
-
-	chosen {
-		stdout-path = "serial2:115200n8";
-	};
-
-	aliases {
-		serial0 = &wkup_uart0;
-		serial1 = &mcu_uart0;
-		serial2 = &main_uart8;
-		mmc0 = &main_sdhci0;
-		mmc1 = &main_sdhci1;
-		i2c0 = &wkup_i2c0;
-		i2c3 = &main_i2c0;
-		ethernet0 = &mcu_cpsw_port1;
-		ethernet1 = &main_cpsw1_port1;
-	};
-
-	memory@80000000 {
-		device_type = "memory";
-		bootph-all;
-		/* 32G RAM */
-		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
-		      <0x00000008 0x80000000 0x00000007 0x80000000>;
-	};
-
-	reserved_memory: reserved-memory {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		secure_ddr: optee@9e800000 {
-			reg = <0x00 0x9e800000 0x00 0x01800000>;
-			no-map;
-		};
-
-		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa0000000 0x00 0x100000>;
-			no-map;
-		};
-
-		mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa0100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa1000000 0x00 0x100000>;
-			no-map;
-		};
-
-		mcu_r5fss0_core1_memory_region: r5f-memory@a1100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa1100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a2000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa2000000 0x00 0x100000>;
-			no-map;
-		};
-
-		main_r5fss0_core0_memory_region: r5f-memory@a2100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa2100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a3000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa3000000 0x00 0x100000>;
-			no-map;
-		};
-
-		main_r5fss0_core1_memory_region: r5f-memory@a3100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa3100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a4000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa4000000 0x00 0x100000>;
-			no-map;
-		};
-
-		main_r5fss1_core0_memory_region: r5f-memory@a4100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa4100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a5000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa5000000 0x00 0x100000>;
-			no-map;
-		};
-
-		main_r5fss1_core1_memory_region: r5f-memory@a5100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa5100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		main_r5fss2_core0_dma_memory_region: r5f-dma-memory@a6000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa6000000 0x00 0x100000>;
-			no-map;
-		};
-
-		main_r5fss2_core0_memory_region: r5f-memory@a6100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa6100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		main_r5fss2_core1_dma_memory_region: r5f-dma-memory@a7000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa7000000 0x00 0x100000>;
-			no-map;
-		};
-
-		main_r5fss2_core1_memory_region: r5f-memory@a7100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa7100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		c71_0_dma_memory_region: c71-dma-memory@a8000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa8000000 0x00 0x100000>;
-			no-map;
-		};
-
-		c71_0_memory_region: c71-memory@a8100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa8100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		c71_1_dma_memory_region: c71-dma-memory@a9000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa9000000 0x00 0x100000>;
-			no-map;
-		};
-
-		c71_1_memory_region: c71-memory@a9100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xa9100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		c71_2_dma_memory_region: c71-dma-memory@aa000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xaa000000 0x00 0x100000>;
-			no-map;
-		};
-
-		c71_2_memory_region: c71-memory@aa100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xaa100000 0x00 0xf00000>;
-			no-map;
-		};
-
-		c71_3_dma_memory_region: c71-dma-memory@ab000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xab000000 0x00 0x100000>;
-			no-map;
-		};
-
-		c71_3_memory_region: c71-memory@ab100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xab100000 0x00 0xf00000>;
-			no-map;
-		};
-	};
-
-	evm_12v0: regulator-evm12v0 {
-		/* main supply */
-		compatible = "regulator-fixed";
-		regulator-name = "evm_12v0";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-always-on;
-		regulator-boot-on;
-	};
-
-	vsys_3v3: regulator-vsys3v3 {
-		/* Output of LM5140 */
-		compatible = "regulator-fixed";
-		regulator-name = "vsys_3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&evm_12v0>;
-		regulator-always-on;
-		regulator-boot-on;
-	};
-
-	vsys_5v0: regulator-vsys5v0 {
-		/* Output of LM5140 */
-		compatible = "regulator-fixed";
-		regulator-name = "vsys_5v0";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&evm_12v0>;
-		regulator-always-on;
-		regulator-boot-on;
-	};
-
-	vdd_mmc1: regulator-sd {
-		/* Output of TPS22918 */
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_mmc1";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		enable-active-high;
-		vin-supply = <&vsys_3v3>;
-		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
-	};
-
-	vdd_sd_dv: regulator-TLV71033 {
-		/* Output of TLV71033 */
-		compatible = "regulator-gpio";
-		regulator-name = "tlv71033";
-		pinctrl-names = "default";
-		pinctrl-0 = <&vdd_sd_dv_pins_default>;
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		vin-supply = <&vsys_5v0>;
-		gpios = <&main_gpio0 8 GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x0>,
-			 <3300000 0x1>;
-	};
-
-	dp0_pwr_3v3: regulator-dp0-prw {
-		compatible = "regulator-fixed";
-		regulator-name = "dp0-pwr";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&exp4 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	dp0: connector-dp0 {
-		compatible = "dp-connector";
-		label = "DP0";
-		type = "full-size";
-		dp-pwr-supply = <&dp0_pwr_3v3>;
-
-		port {
-			dp0_connector_in: endpoint {
-				remote-endpoint = <&dp0_out>;
-			};
-		};
-	};
-
-	transceiver0: can-phy0 {
-		compatible = "ti,tcan1042";
-		#phy-cells = <0>;
-		max-bitrate = <5000000>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&mcu_mcan0_gpio_pins_default>;
-		standby-gpios = <&wkup_gpio0 69 GPIO_ACTIVE_HIGH>;
-	};
-
-	transceiver1: can-phy1 {
-		compatible = "ti,tcan1042";
-		#phy-cells = <0>;
-		max-bitrate = <5000000>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&mcu_mcan1_gpio_pins_default>;
-		standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
-	};
-
-	transceiver2: can-phy2 {
-		/* standby pin has been grounded by default */
-		compatible = "ti,tcan1042";
-		#phy-cells = <0>;
-		max-bitrate = <5000000>;
-	};
-
-	transceiver3: can-phy3 {
-		compatible = "ti,tcan1042";
-		#phy-cells = <0>;
-		max-bitrate = <5000000>;
-		standby-gpios = <&exp2 7 GPIO_ACTIVE_HIGH>;
-		mux-states = <&mux1 1>;
-	};
-
-	mux1: mux-controller {
-		compatible = "gpio-mux";
-		#mux-state-cells = <1>;
-		mux-gpios = <&exp2 14 GPIO_ACTIVE_HIGH>;
-		idle-state = <1>;
-	};
-
-	codec_audio: sound {
-		compatible = "ti,j7200-cpb-audio";
-		model = "j784s4-cpb";
-
-		ti,cpb-mcasp = <&mcasp0>;
-		ti,cpb-codec = <&pcm3168a_1>;
-
-		clocks = <&k3_clks 265 0>, <&k3_clks 265 1>,
-			 <&k3_clks 157 34>, <&k3_clks 157 63>;
-		clock-names = "cpb-mcasp-auxclk", "cpb-mcasp-auxclk-48000",
-			      "cpb-codec-scki", "cpb-codec-scki-48000";
-	};
-};
-
-&wkup_gpio0 {
-	status = "okay";
-};
-
-&main_pmx0 {
-	bootph-all;
-	main_cpsw2g_default_pins: main-cpsw2g-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
-			J784S4_IOPAD(0x0a0, PIN_INPUT, 6) /* (AD34) MCASP0_AXR12.RGMII1_RD1 */
-			J784S4_IOPAD(0x0a4, PIN_INPUT, 6) /* (AJ36) MCASP0_AXR13.RGMII1_RD2 */
-			J784S4_IOPAD(0x0a8, PIN_INPUT, 6) /* (AF34) MCASP0_AXR14.RGMII1_RD3 */
-			J784S4_IOPAD(0x0b0, PIN_INPUT, 6) /* (AL33) MCASP1_AXR3.RGMII1_RXC */
-			J784S4_IOPAD(0x0ac, PIN_INPUT, 6) /* (AE34) MCASP0_AXR15.RGMII1_RX_CTL */
-			J784S4_IOPAD(0x08c, PIN_INPUT, 6) /* (AE35) MCASP0_AXR7.RGMII1_TD0 */
-			J784S4_IOPAD(0x090, PIN_INPUT, 6) /* (AC35) MCASP0_AXR8.RGMII1_TD1 */
-			J784S4_IOPAD(0x094, PIN_INPUT, 6) /* (AG35) MCASP0_AXR9.RGMII1_TD2 */
-			J784S4_IOPAD(0x098, PIN_INPUT, 6) /* (AH36) MCASP0_AXR10.RGMII1_TD3 */
-			J784S4_IOPAD(0x0b4, PIN_INPUT, 6) /* (AL34) MCASP1_AXR4.RGMII1_TXC */
-			J784S4_IOPAD(0x09c, PIN_INPUT, 6) /* (AF35) MCASP0_AXR11.RGMII1_TX_CTL */
-		>;
-	};
-
-	main_cpsw2g_mdio_default_pins: main-cpsw2g-mdio-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x0c0, PIN_INPUT, 6) /* (AD38) MCASP1_AXR0.MDIO0_MDC */
-			J784S4_IOPAD(0x0bc, PIN_INPUT, 6) /* (AD33) MCASP1_AFSX.MDIO0_MDIO */
-		>;
-	};
-
-	main_uart8_pins_default: main-uart8-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x040, PIN_INPUT, 14) /* (AF37) MCASP0_AXR0.UART8_CTSn */
-			J784S4_IOPAD(0x044, PIN_OUTPUT, 14) /* (AG37) MCASP0_AXR1.UART8_RTSn */
-			J784S4_IOPAD(0x0d0, PIN_INPUT, 11) /* (AP38) SPI0_CS1.UART8_RXD */
-			J784S4_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AN38) SPI0_CLK.UART8_TXD */
-		>;
-	};
-
-	main_i2c0_pins_default: main-i2c0-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AN36) I2C0_SCL */
-			J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */
-		>;
-	};
-
-	main_i2c5_pins_default: main-i2c5-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x01c, PIN_INPUT, 8) /* (AG34) MCAN15_TX.I2C5_SCL */
-			J784S4_IOPAD(0x018, PIN_INPUT, 8) /* (AK36) MCAN14_RX.I2C5_SDA */
-		>;
-	};
-
-	main_mmc1_pins_default: main-mmc1-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x104, PIN_INPUT, 0) /* (AB38) MMC1_CLK */
-			J784S4_IOPAD(0x108, PIN_INPUT, 0) /* (AB36) MMC1_CMD */
-			J784S4_IOPAD(0x100, PIN_INPUT, 0) /* (No Pin) MMC1_CLKLB */
-			J784S4_IOPAD(0x0fc, PIN_INPUT, 0) /* (AA33) MMC1_DAT0 */
-			J784S4_IOPAD(0x0f8, PIN_INPUT, 0) /* (AB34) MMC1_DAT1 */
-			J784S4_IOPAD(0x0f4, PIN_INPUT, 0) /* (AA32) MMC1_DAT2 */
-			J784S4_IOPAD(0x0f0, PIN_INPUT, 0) /* (AC38) MMC1_DAT3 */
-			J784S4_IOPAD(0x0e8, PIN_INPUT, 8) /* (AR38) TIMER_IO0.MMC1_SDCD */
-		>;
-	};
-
-	vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
-		>;
-	};
-
-	dp0_pins_default: dp0-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x0cc, PIN_INPUT, 12) /* (AM37) SPI0_CS0.DP0_HPD */
-		>;
-	};
-
-	main_i2c4_pins_default: main-i2c4-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x014, PIN_INPUT_PULLUP, 8) /* (AG33) MCAN14_TX.I2C4_SCL */
-			J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
-		>;
-	};
-
-	main_mcan4_pins_default: main-mcan4-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x088, PIN_INPUT, 0) /* (AF36) MCAN4_RX */
-			J784S4_IOPAD(0x084, PIN_OUTPUT, 0) /* (AG38) MCAN4_TX */
-		>;
-	};
-
-	main_mcan16_pins_default: main-mcan16-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x028, PIN_INPUT, 0) /* (AE33) MCAN16_RX */
-			J784S4_IOPAD(0x024, PIN_OUTPUT, 0) /* (AH34) MCAN16_TX */
-		>;
-	};
-
-	main_usbss0_pins_default: main-usbss0-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AN37) TIMER_IO1.USB0_DRVVBUS */
-		>;
-	};
-
-	main_i2c3_pins_default: main-i2c3-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x064, PIN_INPUT, 13) /* (AF38) MCAN0_TX.I2C3_SCL */
-			J784S4_IOPAD(0x060, PIN_INPUT, 13) /* (AE36) MCASP2_AXR1.I2C3_SDA */
-		>;
-	};
-
-	main_mcasp0_pins_default: main-mcasp0-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x038, PIN_OUTPUT_PULLDOWN, 1) /* (AK35) MCASP0_ACLKX */
-			J784S4_IOPAD(0x03c, PIN_OUTPUT_PULLDOWN, 1) /* (AK38) MCASP0_AFSX */
-			J784S4_IOPAD(0x07c, PIN_OUTPUT_PULLDOWN, 1) /* (AJ38) MCASP0_AXR3 */
-			J784S4_IOPAD(0x080, PIN_INPUT_PULLDOWN, 1) /* (AK34) MCASP0_AXR4 */
-		>;
-	};
-
-	audio_ext_refclk1_pins_default: audio-ext-refclk1-default-pins {
-		pinctrl-single,pins = <
-			J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
-		>;
-	};
-};
-
-&wkup_pmx2 {
-	bootph-all;
-	wkup_uart0_pins_default: wkup-uart0-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */
-			J784S4_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (K34) WKUP_UART0_TXD */
-		>;
-	};
-
-	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
-			J784S4_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
-		>;
-	};
-
-	mcu_uart0_pins_default: mcu-uart0-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (H37) WKUP_GPIO0_14.MCU_UART0_CTSn */
-			J784S4_WKUP_IOPAD(0x094, PIN_OUTPUT, 0) /* (K37) WKUP_GPIO0_15.MCU_UART0_RTSn */
-			J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (K38) WKUP_GPIO0_13.MCU_UART0_RXD */
-			J784S4_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (J37) WKUP_GPIO0_12.MCU_UART0_TXD */
-		>;
-	};
-
-	mcu_cpsw_pins_default: mcu-cpsw-default-pins {
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x02c, PIN_INPUT, 0) /* (A35) MCU_RGMII1_RD0 */
-			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (B36) MCU_RGMII1_RD1 */
-			J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (C36) MCU_RGMII1_RD2 */
-			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D36) MCU_RGMII1_RD3 */
-			J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (B37) MCU_RGMII1_RXC */
-			J784S4_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (C37) MCU_RGMII1_RX_CTL */
-			J784S4_WKUP_IOPAD(0x014, PIN_OUTPUT, 0) /* (D37) MCU_RGMII1_TD0 */
-			J784S4_WKUP_IOPAD(0x010, PIN_OUTPUT, 0) /* (D38) MCU_RGMII1_TD1 */
-			J784S4_WKUP_IOPAD(0x00c, PIN_OUTPUT, 0) /* (E37) MCU_RGMII1_TD2 */
-			J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E38) MCU_RGMII1_TD3 */
-			J784S4_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (E36) MCU_RGMII1_TXC */
-			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (C38) MCU_RGMII1_TX_CTL */
-		>;
-	};
-
-	mcu_mdio_pins_default: mcu-mdio-default-pins {
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A36) MCU_MDIO0_MDC */
-			J784S4_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (B35) MCU_MDIO0_MDIO */
-		>;
-	};
-
-	mcu_adc0_pins_default: mcu-adc0-default-pins {
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x0cc, PIN_INPUT, 0) /* (P36) MCU_ADC0_AIN0 */
-			J784S4_WKUP_IOPAD(0x0d0, PIN_INPUT, 0) /* (V36) MCU_ADC0_AIN1 */
-			J784S4_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (T34) MCU_ADC0_AIN2 */
-			J784S4_WKUP_IOPAD(0x0d8, PIN_INPUT, 0) /* (T36) MCU_ADC0_AIN3 */
-			J784S4_WKUP_IOPAD(0x0dc, PIN_INPUT, 0) /* (P34) MCU_ADC0_AIN4 */
-			J784S4_WKUP_IOPAD(0x0e0, PIN_INPUT, 0) /* (R37) MCU_ADC0_AIN5 */
-			J784S4_WKUP_IOPAD(0x0e4, PIN_INPUT, 0) /* (R33) MCU_ADC0_AIN6 */
-			J784S4_WKUP_IOPAD(0x0e8, PIN_INPUT, 0) /* (V38) MCU_ADC0_AIN7 */
-		>;
-	};
-
-	mcu_adc1_pins_default: mcu-adc1-default-pins {
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x0ec, PIN_INPUT, 0) /* (Y38) MCU_ADC1_AIN0 */
-			J784S4_WKUP_IOPAD(0x0f0, PIN_INPUT, 0) /* (Y34) MCU_ADC1_AIN1 */
-			J784S4_WKUP_IOPAD(0x0f4, PIN_INPUT, 0) /* (V34) MCU_ADC1_AIN2 */
-			J784S4_WKUP_IOPAD(0x0f8, PIN_INPUT, 0) /* (W37) MCU_ADC1_AIN3 */
-			J784S4_WKUP_IOPAD(0x0fc, PIN_INPUT, 0) /* (AA37) MCU_ADC1_AIN4 */
-			J784S4_WKUP_IOPAD(0x100, PIN_INPUT, 0) /* (W33) MCU_ADC1_AIN5 */
-			J784S4_WKUP_IOPAD(0x104, PIN_INPUT, 0) /* (U33) MCU_ADC1_AIN6 */
-			J784S4_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
-		>;
-	};
-
-	mcu_mcan0_pins_default: mcu-mcan0-default-pins {
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x050, PIN_OUTPUT, 0) /* (K33) MCU_MCAN0_TX */
-			J784S4_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (F38) MCU_MCAN0_RX */
-		>;
-	};
-
-	mcu_mcan1_pins_default: mcu-mcan1-default-pins {
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (H35) WKUP_GPIO0_4.MCU_MCAN1_TX */
-			J784S4_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (K36) WKUP_GPIO0_5.MCU_MCAN1_RX */
-		>;
-	};
-
-	mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-default-pins {
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x040, PIN_INPUT, 7) /* (J38) MCU_SPI0_D1.WKUP_GPIO0_69 */
-		>;
-	};
-
-	mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-default-pins {
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x060, PIN_INPUT, 7) /* (J35) WKUP_GPIO0_2 */
-		>;
-	};
-};
-
-&wkup_pmx1 {
-	status = "okay";
-
-	pmic_irq_pins_default: pmic-irq-default-pins {
-		pinctrl-single,pins = <
-			/* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
-			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
-		>;
-	};
-};
-
-&wkup_pmx0 {
-	bootph-all;
-	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
-			J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
-			J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
-			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
-			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
-			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
-			J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
-			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
-			J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
-			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
-			J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
-		>;
-	};
-};
-
-&wkup_pmx1 {
-	bootph-all;
-	mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
-			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
-		>;
-	};
-
-	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
-		bootph-all;
-		pinctrl-single,pins = <
-			J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
-			J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
-			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
-			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
-			J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
-			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
-			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
-			J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
-		>;
-	};
-};
-
-&wkup_uart0 {
-	/* Firmware usage */
-	status = "reserved";
-	pinctrl-names = "default";
-	pinctrl-0 = <&wkup_uart0_pins_default>;
-};
-
-&wkup_i2c0 {
-	bootph-all;
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&wkup_i2c0_pins_default>;
-	clock-frequency = <400000>;
-
-	eeprom@50 {
-		/* CAV24C256WE-GT3 */
-		compatible = "atmel,24c256";
-		reg = <0x50>;
-	};
-
-	tps659413: pmic@48 {
-		compatible = "ti,tps6594-q1";
-		reg = <0x48>;
-		system-power-controller;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pmic_irq_pins_default>;
-		interrupt-parent = <&wkup_gpio0>;
-		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		ti,primary-pmic;
-		buck12-supply = <&vsys_3v3>;
-		buck3-supply = <&vsys_3v3>;
-		buck4-supply = <&vsys_3v3>;
-		buck5-supply = <&vsys_3v3>;
-		ldo1-supply = <&vsys_3v3>;
-		ldo2-supply = <&vsys_3v3>;
-		ldo3-supply = <&vsys_3v3>;
-		ldo4-supply = <&vsys_3v3>;
-
-		regulators {
-			bucka12: buck12 {
-				regulator-name = "vdd_ddr_1v1";
-				regulator-min-microvolt = <1100000>;
-				regulator-max-microvolt = <1100000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			bucka3: buck3 {
-				regulator-name = "vdd_ram_0v85";
-				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <850000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			bucka4: buck4 {
-				regulator-name = "vdd_io_1v8";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			bucka5: buck5 {
-				regulator-name = "vdd_mcu_0v85";
-				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <850000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			ldoa1: ldo1 {
-				regulator-name = "vdd_mcuio_1v8";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			ldoa2: ldo2 {
-				regulator-name = "vdd_mcuio_3v3";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			ldoa3: ldo3 {
-				regulator-name = "vds_dll_0v8";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <800000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			ldoa4: ldo4 {
-				regulator-name = "vda_mcu_1v8";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-		};
-	};
-
-	tps62873a: regulator@40 {
-		compatible = "ti,tps62873";
-		reg = <0x40>;
-		bootph-pre-ram;
-		regulator-name = "VDD_CPU_AVS";
-		regulator-min-microvolt = <750000>;
-		regulator-max-microvolt = <1330000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	tps62873b: regulator@43 {
-		compatible = "ti,tps62873";
-		reg = <0x43>;
-		regulator-name = "VDD_CORE_0V8";
-		regulator-min-microvolt = <760000>;
-		regulator-max-microvolt = <840000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-};
-
-&mcu_uart0 {
-	bootph-all;
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcu_uart0_pins_default>;
-};
-
-&main_uart8 {
-	bootph-all;
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_uart8_pins_default>;
-};
-
-&ufs_wrapper {
-	status = "okay";
-};
-
-&fss {
-	bootph-all;
-	status = "okay";
-};
-
-&ospi0 {
-	bootph-all;
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
-
-	flash@0 {
-		bootph-all;
-		compatible = "jedec,spi-nor";
-		reg = <0x0>;
-		spi-tx-bus-width = <8>;
-		spi-rx-bus-width = <8>;
-		spi-max-frequency = <25000000>;
-		cdns,tshsl-ns = <60>;
-		cdns,tsd2d-ns = <60>;
-		cdns,tchsh-ns = <60>;
-		cdns,tslch-ns = <60>;
-		cdns,read-delay = <4>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "ospi.tiboot3";
-				reg = <0x0 0x80000>;
-			};
-
-			partition@80000 {
-				label = "ospi.tispl";
-				reg = <0x80000 0x200000>;
-			};
-
-			partition@280000 {
-				label = "ospi.u-boot";
-				reg = <0x280000 0x400000>;
-			};
-
-			partition@680000 {
-				label = "ospi.env";
-				reg = <0x680000 0x40000>;
-			};
-
-			partition@6c0000 {
-				label = "ospi.env.backup";
-				reg = <0x6c0000 0x40000>;
-			};
-
-			partition@800000 {
-				label = "ospi.rootfs";
-				reg = <0x800000 0x37c0000>;
-			};
-
-			partition@3fc0000 {
-				bootph-all;
-				label = "ospi.phypattern";
-				reg = <0x3fc0000 0x40000>;
-			};
-		};
-	};
-};
-
-&ospi1 {
-	bootph-all;
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
-
-	flash@0 {
-		bootph-all;
-		compatible = "jedec,spi-nor";
-		reg = <0x0>;
-		spi-tx-bus-width = <1>;
-		spi-rx-bus-width = <4>;
-		spi-max-frequency = <40000000>;
-		cdns,tshsl-ns = <60>;
-		cdns,tsd2d-ns = <60>;
-		cdns,tchsh-ns = <60>;
-		cdns,tslch-ns = <60>;
-		cdns,read-delay = <2>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "qspi.tiboot3";
-				reg = <0x0 0x80000>;
-			};
-
-			partition@80000 {
-				label = "qspi.tispl";
-				reg = <0x80000 0x200000>;
-			};
-
-			partition@280000 {
-				label = "qspi.u-boot";
-				reg = <0x280000 0x400000>;
-			};
-
-			partition@680000 {
-				label = "qspi.env";
-				reg = <0x680000 0x40000>;
-			};
-
-			partition@6c0000 {
-				label = "qspi.env.backup";
-				reg = <0x6c0000 0x40000>;
-			};
-
-			partition@800000 {
-				label = "qspi.rootfs";
-				reg = <0x800000 0x37c0000>;
-			};
-
-			partition@3fc0000 {
-				bootph-all;
-				label = "qspi.phypattern";
-				reg = <0x3fc0000 0x40000>;
-			};
-		};
-
-	};
-};
-
-&main_i2c0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_i2c0_pins_default>;
-
-	clock-frequency = <400000>;
-
-	exp1: gpio@20 {
-		compatible = "ti,tca6416";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-line-names = "PCIE1_2L_MODE_SEL", "PCIE1_4L_PERSTZ", "PCIE1_2L_RC_RSTZ",
-				  "PCIE1_2L_EP_RST_EN", "PCIE0_4L_MODE_SEL", "PCIE0_4L_PERSTZ",
-				  "PCIE0_4L_RC_RSTZ", "PCIE0_4L_EP_RST_EN", "PCIE1_4L_PRSNT#",
-				  "PCIE0_4L_PRSNT#", "CDCI1_OE1/OE4", "CDCI1_OE2/OE3",
-				  "AUDIO_MUX_SEL", "EXP_MUX2", "EXP_MUX3", "GESI_EXP_PHY_RSTZ";
-
-		p12-hog {
-			/* P12 - AUDIO_MUX_SEL */
-			gpio-hog;
-			gpios = <12 GPIO_ACTIVE_HIGH>;
-			output-low;
-			line-name = "AUDIO_MUX_SEL";
-		};
-	};
-
-	exp2: gpio@22 {
-		compatible = "ti,tca6424";
-		reg = <0x22>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-line-names = "R_GPIO_RGMII1_RST", "ENET2_I2CMUX_SEL", "GPIO_USD_PWR_EN",
-				  "USBC_PWR_EN", "USBC_MODE_SEL1", "USBC_MODE_SEL0",
-				  "GPIO_LIN_EN", "R_CAN_STB", "CTRL_PM_I2C_OE#",
-				  "ENET2_EXP_PWRDN", "ENET2_EXP_SPARE2", "CDCI2_RSTZ",
-				  "USB2.0_MUX_SEL", "CANUART_MUX_SEL0", "CANUART_MUX2_SEL1",
-				  "CANUART_MUX1_SEL1", "ENET1_EXP_PWRDN", "ENET1_EXP_RESETZ",
-				  "ENET1_I2CMUX_SEL", "ENET1_EXP_SPARE2", "ENET2_EXP_RESETZ",
-				  "USER_INPUT1", "USER_LED1", "USER_LED2";
-
-		p13-hog {
-			/* P13 - CANUART_MUX_SEL0 */
-			gpio-hog;
-			gpios = <13 GPIO_ACTIVE_HIGH>;
-			output-high;
-			line-name = "CANUART_MUX_SEL0";
-		};
-
-		p15-hog {
-			/* P15 - CANUART_MUX1_SEL1 */
-			gpio-hog;
-			gpios = <15 GPIO_ACTIVE_HIGH>;
-			output-high;
-			line-name = "CANUART_MUX1_SEL1";
-		};
-	};
-};
-
-&main_i2c5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_i2c5_pins_default>;
-	clock-frequency = <400000>;
-	status = "okay";
-
-	exp5: gpio@20 {
-		compatible = "ti,tca6408";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-line-names = "CSI2_EXP_RSTZ", "CSI2_EXP_A_GPIO0",
-				  "CSI2_EXP_A_GPIO1", "CSI2_EXP_A_GPIO3",
-				  "CSI2_EXP_B_GPIO1", "CSI2_EXP_B_GPIO2",
-				  "CSI2_EXP_B_GPIO3", "CSI2_EXP_B_GPIO4";
-	};
-};
-
-&main_sdhci0 {
-	bootph-all;
-	/* eMMC */
-	status = "okay";
-	non-removable;
-	ti,driver-strength-ohm = <50>;
-	disable-wp;
-};
-
-&main_sdhci1 {
-	bootph-all;
-	/* SD card */
-	status = "okay";
-	pinctrl-0 = <&main_mmc1_pins_default>;
-	pinctrl-names = "default";
-	disable-wp;
-	vmmc-supply = <&vdd_mmc1>;
-	vqmmc-supply = <&vdd_sd_dv>;
-};
-
-&main_gpio0 {
-	status = "okay";
-};
-
-&mcu_cpsw {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcu_cpsw_pins_default>;
-};
-
-&davinci_mdio {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcu_mdio_pins_default>;
-
-	mcu_phy0: ethernet-phy@0 {
-		reg = <0>;
-		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
-		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
-		ti,min-output-impedance;
-	};
-};
-
-&mcu_cpsw_port1 {
-	status = "okay";
-	phy-mode = "rgmii-rxid";
-	phy-handle = <&mcu_phy0>;
-};
-
-&main_cpsw1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_cpsw2g_default_pins>;
-	status = "okay";
-};
-
-&main_cpsw1_mdio {
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_cpsw2g_mdio_default_pins>;
-	status = "okay";
-
-	main_cpsw1_phy0: ethernet-phy@0 {
-		reg = <0>;
-		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
-		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
-		ti,min-output-impedance;
-	};
-};
-
-&main_cpsw1_port1 {
-	phy-mode = "rgmii-rxid";
-	phy-handle = <&main_cpsw1_phy0>;
-	status = "okay";
-};
-
-&mailbox0_cluster0 {
-	status = "okay";
-	interrupts = <436>;
-
-	mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
-		ti,mbox-rx = <0 0 0>;
-		ti,mbox-tx = <1 0 0>;
-	};
-
-	mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
-		ti,mbox-rx = <2 0 0>;
-		ti,mbox-tx = <3 0 0>;
-	};
-};
-
-&mailbox0_cluster1 {
-	status = "okay";
-	interrupts = <432>;
-
-	mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 {
-		ti,mbox-rx = <0 0 0>;
-		ti,mbox-tx = <1 0 0>;
-	};
-
-	mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 {
-		ti,mbox-rx = <2 0 0>;
-		ti,mbox-tx = <3 0 0>;
-	};
-};
-
-&mailbox0_cluster2 {
-	status = "okay";
-	interrupts = <428>;
-
-	mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 {
-		ti,mbox-rx = <0 0 0>;
-		ti,mbox-tx = <1 0 0>;
-	};
-
-	mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 {
-		ti,mbox-rx = <2 0 0>;
-		ti,mbox-tx = <3 0 0>;
-	};
-};
-
-&mailbox0_cluster3 {
-	status = "okay";
-	interrupts = <424>;
-
-	mbox_main_r5fss2_core0: mbox-main-r5fss2-core0 {
-		ti,mbox-rx = <0 0 0>;
-		ti,mbox-tx = <1 0 0>;
-	};
-
-	mbox_main_r5fss2_core1: mbox-main-r5fss2-core1 {
-		ti,mbox-rx = <2 0 0>;
-		ti,mbox-tx = <3 0 0>;
-	};
-};
-
-&mailbox0_cluster4 {
-	status = "okay";
-	interrupts = <420>;
-
-	mbox_c71_0: mbox-c71-0 {
-		ti,mbox-rx = <0 0 0>;
-		ti,mbox-tx = <1 0 0>;
-	};
-
-	mbox_c71_1: mbox-c71-1 {
-		ti,mbox-rx = <2 0 0>;
-		ti,mbox-tx = <3 0 0>;
-	};
-};
-
-&mailbox0_cluster5 {
-	status = "okay";
-	interrupts = <416>;
-
-	mbox_c71_2: mbox-c71-2 {
-		ti,mbox-rx = <0 0 0>;
-		ti,mbox-tx = <1 0 0>;
-	};
-
-	mbox_c71_3: mbox-c71-3 {
-		ti,mbox-rx = <2 0 0>;
-		ti,mbox-tx = <3 0 0>;
-	};
-};
-
-&mcu_r5fss0_core0 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
-	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
-			<&mcu_r5fss0_core0_memory_region>;
-};
-
-&mcu_r5fss0_core1 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core1>;
-	memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
-			<&mcu_r5fss0_core1_memory_region>;
-};
-
-&main_r5fss0_core0 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core0>;
-	memory-region = <&main_r5fss0_core0_dma_memory_region>,
-			<&main_r5fss0_core0_memory_region>;
-};
-
-&main_r5fss0_core1 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core1>;
-	memory-region = <&main_r5fss0_core1_dma_memory_region>,
-			<&main_r5fss0_core1_memory_region>;
-};
-
-&main_r5fss1_core0 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster2 &mbox_main_r5fss1_core0>;
-	memory-region = <&main_r5fss1_core0_dma_memory_region>,
-			<&main_r5fss1_core0_memory_region>;
-};
-
-&main_r5fss1_core1 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster2 &mbox_main_r5fss1_core1>;
-	memory-region = <&main_r5fss1_core1_dma_memory_region>,
-			<&main_r5fss1_core1_memory_region>;
-};
-
-&main_r5fss2_core0 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster3 &mbox_main_r5fss2_core0>;
-	memory-region = <&main_r5fss2_core0_dma_memory_region>,
-			<&main_r5fss2_core0_memory_region>;
-};
-
-&main_r5fss2_core1 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster3 &mbox_main_r5fss2_core1>;
-	memory-region = <&main_r5fss2_core1_dma_memory_region>,
-			<&main_r5fss2_core1_memory_region>;
-};
-
-&c71_0 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster4 &mbox_c71_0>;
-	memory-region = <&c71_0_dma_memory_region>,
-			<&c71_0_memory_region>;
-};
-
-&c71_1 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster4 &mbox_c71_1>;
-	memory-region = <&c71_1_dma_memory_region>,
-			<&c71_1_memory_region>;
-};
-
-&c71_2 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster5 &mbox_c71_2>;
-	memory-region = <&c71_2_dma_memory_region>,
-			<&c71_2_memory_region>;
-};
-
-&c71_3 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster5 &mbox_c71_3>;
-	memory-region = <&c71_3_dma_memory_region>,
-			<&c71_3_memory_region>;
-};
-
-&tscadc0 {
-	pinctrl-0 = <&mcu_adc0_pins_default>;
-	pinctrl-names = "default";
-	status = "okay";
-	adc {
-		ti,adc-channels = <0 1 2 3 4 5 6 7>;
-	};
-};
-
-&tscadc1 {
-	pinctrl-0 = <&mcu_adc1_pins_default>;
-	pinctrl-names = "default";
-	status = "okay";
-	adc {
-		ti,adc-channels = <0 1 2 3 4 5 6 7>;
-	};
-};
-
-&serdes_refclk {
-	status = "okay";
-	clock-frequency = <100000000>;
-};
-
-&dss {
-	status = "okay";
-	assigned-clocks = <&k3_clks 218 2>,
-			  <&k3_clks 218 5>,
-			  <&k3_clks 218 14>,
-			  <&k3_clks 218 18>;
-	assigned-clock-parents = <&k3_clks 218 3>,
-				 <&k3_clks 218 7>,
-				 <&k3_clks 218 16>,
-				 <&k3_clks 218 22>;
-};
-
-&serdes0 {
-	status = "okay";
-
-	serdes0_pcie1_link: phy@0 {
-		reg = <0>;
-		cdns,num-lanes = <2>;
-		#phy-cells = <0>;
-		cdns,phy-type = <PHY_TYPE_PCIE>;
-		resets = <&serdes_wiz0 1>, <&serdes_wiz0 2>;
-	};
-
-	serdes0_usb_link: phy@3 {
-		reg = <3>;
-		cdns,num-lanes = <1>;
-		#phy-cells = <0>;
-		cdns,phy-type = <PHY_TYPE_USB3>;
-		resets = <&serdes_wiz0 4>;
-	};
-};
-
-&serdes_wiz0 {
-	status = "okay";
-};
-
-&usb_serdes_mux {
-	idle-states = <0>; /* USB0 to SERDES lane 3 */
-};
-
-&usbss0 {
-	status = "okay";
-	pinctrl-0 = <&main_usbss0_pins_default>;
-	pinctrl-names = "default";
-	ti,vbus-divider;
-};
-
-&usb0 {
-	dr_mode = "otg";
-	maximum-speed = "super-speed";
-	phys = <&serdes0_usb_link>;
-	phy-names = "cdns3,usb3-phy";
-};
-
-&serdes_wiz4 {
-	status = "okay";
-};
-
-&serdes4 {
-	status = "okay";
-	serdes4_dp_link: phy@0 {
-		reg = <0>;
-		cdns,num-lanes = <4>;
-		#phy-cells = <0>;
-		cdns,phy-type = <PHY_TYPE_DP>;
-		resets = <&serdes_wiz4 1>, <&serdes_wiz4 2>,
-			 <&serdes_wiz4 3>, <&serdes_wiz4 4>;
-	};
-};
-
-&mhdp {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&dp0_pins_default>;
-	phys = <&serdes4_dp_link>;
-	phy-names = "dpphy";
-};
-
-&dss_ports {
-	/* DP */
-	port {
-		dpi0_out: endpoint {
-			remote-endpoint = <&dp0_in>;
-		};
-	};
-};
-
-&main_i2c4 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_i2c4_pins_default>;
-	clock-frequency = <400000>;
-
-	exp4: gpio@20 {
-		compatible = "ti,tca6408";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-};
-
-&dp0_ports {
-	port@0 {
-		reg = <0>;
-
-		dp0_in: endpoint {
-			remote-endpoint = <&dpi0_out>;
-		};
-	};
-
-	port@4 {
-		reg = <4>;
-
-		dp0_out: endpoint {
-			remote-endpoint = <&dp0_connector_in>;
-		};
-	};
-};
-
-&mcu_mcan0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcu_mcan0_pins_default>;
-	phys = <&transceiver0>;
-};
-
-&mcu_mcan1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcu_mcan1_pins_default>;
-	phys = <&transceiver1>;
-};
-
-&main_mcan16 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_mcan16_pins_default>;
-	phys = <&transceiver2>;
-};
-
-&main_mcan4 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_mcan4_pins_default>;
-	phys = <&transceiver3>;
-};
-
-&pcie1_rc {
-	status = "okay";
-	num-lanes = <2>;
-	reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>;
-	phys = <&serdes0_pcie1_link>;
-	phy-names = "pcie-phy";
-};
-
-&serdes1 {
-	status = "okay";
-
-	serdes1_pcie0_link: phy@0 {
-		reg = <0>;
-		cdns,num-lanes = <2>;
-		#phy-cells = <0>;
-		cdns,phy-type = <PHY_TYPE_PCIE>;
-		resets = <&serdes_wiz1 1>, <&serdes_wiz1 2>;
-	};
-};
-
-&serdes_wiz1 {
-	status = "okay";
-};
-
-&pcie0_rc {
-	status = "okay";
-	reset-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
-	phys = <&serdes1_pcie0_link>;
-	phy-names = "pcie-phy";
-};
-
-&k3_clks {
-	/* Confiure AUDIO_EXT_REFCLK1 pin as output */
-	pinctrl-names = "default";
-	pinctrl-0 = <&audio_ext_refclk1_pins_default>;
-};
-
-&main_i2c3 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_i2c3_pins_default>;
-	clock-frequency = <400000>;
-
-	exp3: gpio@20 {
-		compatible = "ti,tca6408";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	pcm3168a_1: audio-codec@44 {
-		compatible = "ti,pcm3168a";
-		reg = <0x44>;
-		#sound-dai-cells = <1>;
-		reset-gpios = <&exp3 0 GPIO_ACTIVE_LOW>;
-		clocks = <&audio_refclk1>;
-		clock-names = "scki";
-		VDD1-supply = <&vsys_3v3>;
-		VDD2-supply = <&vsys_3v3>;
-		VCCAD1-supply = <&vsys_5v0>;
-		VCCAD2-supply = <&vsys_5v0>;
-		VCCDA1-supply = <&vsys_5v0>;
-		VCCDA2-supply = <&vsys_5v0>;
-	};
-};
-
-&mcasp0 {
-	status = "okay";
-	#sound-dai-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_mcasp0_pins_default>;
-	op-mode = <0>;          /* MCASP_IIS_MODE */
-	tdm-slots = <2>;
-	auxclk-fs-ratio = <256>;
-	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
-		0 0 0 1
-		2 0 0 0
-		0 0 0 0
-		0 0 0 0
-	>;
-};
+#include "k3-j784s4-j742s2-evm-common.dtsi"
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
new file mode 100644
index 000000000000..ffa38f41679d
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
@@ -0,0 +1,1477 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * EVM Board Schematics: https://www.ti.com/lit/zip/sprr458
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-j784s4.dtsi"
+
+/ {
+	compatible = "ti,j784s4-evm", "ti,j784s4";
+	model = "Texas Instruments J784S4 EVM";
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	aliases {
+		serial0 = &wkup_uart0;
+		serial1 = &mcu_uart0;
+		serial2 = &main_uart8;
+		mmc0 = &main_sdhci0;
+		mmc1 = &main_sdhci1;
+		i2c0 = &wkup_i2c0;
+		i2c3 = &main_i2c0;
+		ethernet0 = &mcu_cpsw_port1;
+		ethernet1 = &main_cpsw1_port1;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		bootph-all;
+		/* 32G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+		      <0x00000008 0x80000000 0x00000007 0x80000000>;
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0000000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa1000000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core1_memory_region: r5f-memory@a1100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa1100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a2000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa2000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss0_core0_memory_region: r5f-memory@a2100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa2100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a3000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa3000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss0_core1_memory_region: r5f-memory@a3100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa3100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a4000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa4000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss1_core0_memory_region: r5f-memory@a4100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa4100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a5000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa5000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss1_core1_memory_region: r5f-memory@a5100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa5100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss2_core0_dma_memory_region: r5f-dma-memory@a6000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa6000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss2_core0_memory_region: r5f-memory@a6100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa6100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss2_core1_dma_memory_region: r5f-dma-memory@a7000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa7000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss2_core1_memory_region: r5f-memory@a7100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa7100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		c71_0_dma_memory_region: c71-dma-memory@a8000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa8000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c71_0_memory_region: c71-memory@a8100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa8100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		c71_1_dma_memory_region: c71-dma-memory@a9000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa9000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c71_1_memory_region: c71-memory@a9100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa9100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		c71_2_dma_memory_region: c71-dma-memory@aa000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xaa000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c71_2_memory_region: c71-memory@aa100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xaa100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		c71_3_dma_memory_region: c71-dma-memory@ab000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xab000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c71_3_memory_region: c71-memory@ab100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xab100000 0x00 0xf00000>;
+			no-map;
+		};
+	};
+
+	evm_12v0: regulator-evm12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: regulator-vsys3v3 {
+		/* Output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_5v0: regulator-vsys5v0 {
+		/* Output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: regulator-sd {
+		/* Output of TPS22918 */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vsys_3v3>;
+		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_sd_dv: regulator-TLV71033 {
+		/* Output of TLV71033 */
+		compatible = "regulator-gpio";
+		regulator-name = "tlv71033";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_sd_dv_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&vsys_5v0>;
+		gpios = <&main_gpio0 8 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
+
+	dp0_pwr_3v3: regulator-dp0-prw {
+		compatible = "regulator-fixed";
+		regulator-name = "dp0-pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&exp4 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	dp0: connector-dp0 {
+		compatible = "dp-connector";
+		label = "DP0";
+		type = "full-size";
+		dp-pwr-supply = <&dp0_pwr_3v3>;
+
+		port {
+			dp0_connector_in: endpoint {
+				remote-endpoint = <&dp0_out>;
+			};
+		};
+	};
+
+	transceiver0: can-phy0 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcu_mcan0_gpio_pins_default>;
+		standby-gpios = <&wkup_gpio0 69 GPIO_ACTIVE_HIGH>;
+	};
+
+	transceiver1: can-phy1 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcu_mcan1_gpio_pins_default>;
+		standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	transceiver2: can-phy2 {
+		/* standby pin has been grounded by default */
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+	};
+
+	transceiver3: can-phy3 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		standby-gpios = <&exp2 7 GPIO_ACTIVE_HIGH>;
+		mux-states = <&mux1 1>;
+	};
+
+	mux1: mux-controller {
+		compatible = "gpio-mux";
+		#mux-state-cells = <1>;
+		mux-gpios = <&exp2 14 GPIO_ACTIVE_HIGH>;
+		idle-state = <1>;
+	};
+
+	codec_audio: sound {
+		compatible = "ti,j7200-cpb-audio";
+		model = "j784s4-cpb";
+
+		ti,cpb-mcasp = <&mcasp0>;
+		ti,cpb-codec = <&pcm3168a_1>;
+
+		clocks = <&k3_clks 265 0>, <&k3_clks 265 1>,
+			 <&k3_clks 157 34>, <&k3_clks 157 63>;
+		clock-names = "cpb-mcasp-auxclk", "cpb-mcasp-auxclk-48000",
+			      "cpb-codec-scki", "cpb-codec-scki-48000";
+	};
+};
+
+&wkup_gpio0 {
+	status = "okay";
+};
+
+&main_pmx0 {
+	bootph-all;
+	main_cpsw2g_default_pins: main-cpsw2g-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
+			J784S4_IOPAD(0x0a0, PIN_INPUT, 6) /* (AD34) MCASP0_AXR12.RGMII1_RD1 */
+			J784S4_IOPAD(0x0a4, PIN_INPUT, 6) /* (AJ36) MCASP0_AXR13.RGMII1_RD2 */
+			J784S4_IOPAD(0x0a8, PIN_INPUT, 6) /* (AF34) MCASP0_AXR14.RGMII1_RD3 */
+			J784S4_IOPAD(0x0b0, PIN_INPUT, 6) /* (AL33) MCASP1_AXR3.RGMII1_RXC */
+			J784S4_IOPAD(0x0ac, PIN_INPUT, 6) /* (AE34) MCASP0_AXR15.RGMII1_RX_CTL */
+			J784S4_IOPAD(0x08c, PIN_INPUT, 6) /* (AE35) MCASP0_AXR7.RGMII1_TD0 */
+			J784S4_IOPAD(0x090, PIN_INPUT, 6) /* (AC35) MCASP0_AXR8.RGMII1_TD1 */
+			J784S4_IOPAD(0x094, PIN_INPUT, 6) /* (AG35) MCASP0_AXR9.RGMII1_TD2 */
+			J784S4_IOPAD(0x098, PIN_INPUT, 6) /* (AH36) MCASP0_AXR10.RGMII1_TD3 */
+			J784S4_IOPAD(0x0b4, PIN_INPUT, 6) /* (AL34) MCASP1_AXR4.RGMII1_TXC */
+			J784S4_IOPAD(0x09c, PIN_INPUT, 6) /* (AF35) MCASP0_AXR11.RGMII1_TX_CTL */
+		>;
+	};
+
+	main_cpsw2g_mdio_default_pins: main-cpsw2g-mdio-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0c0, PIN_INPUT, 6) /* (AD38) MCASP1_AXR0.MDIO0_MDC */
+			J784S4_IOPAD(0x0bc, PIN_INPUT, 6) /* (AD33) MCASP1_AFSX.MDIO0_MDIO */
+		>;
+	};
+
+	main_uart8_pins_default: main-uart8-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x040, PIN_INPUT, 14) /* (AF37) MCASP0_AXR0.UART8_CTSn */
+			J784S4_IOPAD(0x044, PIN_OUTPUT, 14) /* (AG37) MCASP0_AXR1.UART8_RTSn */
+			J784S4_IOPAD(0x0d0, PIN_INPUT, 11) /* (AP38) SPI0_CS1.UART8_RXD */
+			J784S4_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AN38) SPI0_CLK.UART8_TXD */
+		>;
+	};
+
+	main_i2c0_pins_default: main-i2c0-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AN36) I2C0_SCL */
+			J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */
+		>;
+	};
+
+	main_i2c5_pins_default: main-i2c5-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x01c, PIN_INPUT, 8) /* (AG34) MCAN15_TX.I2C5_SCL */
+			J784S4_IOPAD(0x018, PIN_INPUT, 8) /* (AK36) MCAN14_RX.I2C5_SDA */
+		>;
+	};
+
+	main_mmc1_pins_default: main-mmc1-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x104, PIN_INPUT, 0) /* (AB38) MMC1_CLK */
+			J784S4_IOPAD(0x108, PIN_INPUT, 0) /* (AB36) MMC1_CMD */
+			J784S4_IOPAD(0x100, PIN_INPUT, 0) /* (No Pin) MMC1_CLKLB */
+			J784S4_IOPAD(0x0fc, PIN_INPUT, 0) /* (AA33) MMC1_DAT0 */
+			J784S4_IOPAD(0x0f8, PIN_INPUT, 0) /* (AB34) MMC1_DAT1 */
+			J784S4_IOPAD(0x0f4, PIN_INPUT, 0) /* (AA32) MMC1_DAT2 */
+			J784S4_IOPAD(0x0f0, PIN_INPUT, 0) /* (AC38) MMC1_DAT3 */
+			J784S4_IOPAD(0x0e8, PIN_INPUT, 8) /* (AR38) TIMER_IO0.MMC1_SDCD */
+		>;
+	};
+
+	vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
+		>;
+	};
+
+	dp0_pins_default: dp0-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0cc, PIN_INPUT, 12) /* (AM37) SPI0_CS0.DP0_HPD */
+		>;
+	};
+
+	main_i2c4_pins_default: main-i2c4-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x014, PIN_INPUT_PULLUP, 8) /* (AG33) MCAN14_TX.I2C4_SCL */
+			J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
+		>;
+	};
+
+	main_mcan4_pins_default: main-mcan4-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x088, PIN_INPUT, 0) /* (AF36) MCAN4_RX */
+			J784S4_IOPAD(0x084, PIN_OUTPUT, 0) /* (AG38) MCAN4_TX */
+		>;
+	};
+
+	main_mcan16_pins_default: main-mcan16-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x028, PIN_INPUT, 0) /* (AE33) MCAN16_RX */
+			J784S4_IOPAD(0x024, PIN_OUTPUT, 0) /* (AH34) MCAN16_TX */
+		>;
+	};
+
+	main_usbss0_pins_default: main-usbss0-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AN37) TIMER_IO1.USB0_DRVVBUS */
+		>;
+	};
+
+	main_i2c3_pins_default: main-i2c3-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x064, PIN_INPUT, 13) /* (AF38) MCAN0_TX.I2C3_SCL */
+			J784S4_IOPAD(0x060, PIN_INPUT, 13) /* (AE36) MCASP2_AXR1.I2C3_SDA */
+		>;
+	};
+
+	main_mcasp0_pins_default: main-mcasp0-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x038, PIN_OUTPUT_PULLDOWN, 1) /* (AK35) MCASP0_ACLKX */
+			J784S4_IOPAD(0x03c, PIN_OUTPUT_PULLDOWN, 1) /* (AK38) MCASP0_AFSX */
+			J784S4_IOPAD(0x07c, PIN_OUTPUT_PULLDOWN, 1) /* (AJ38) MCASP0_AXR3 */
+			J784S4_IOPAD(0x080, PIN_INPUT_PULLDOWN, 1) /* (AK34) MCASP0_AXR4 */
+		>;
+	};
+
+	audio_ext_refclk1_pins_default: audio-ext-refclk1-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
+		>;
+	};
+};
+
+&wkup_pmx2 {
+	bootph-all;
+	wkup_uart0_pins_default: wkup-uart0-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */
+			J784S4_WKUP_IOPAD(0x04c, PIN_OUTPUT, 0) /* (K34) WKUP_UART0_TXD */
+		>;
+	};
+
+	wkup_i2c0_pins_default: wkup-i2c0-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */
+			J784S4_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */
+		>;
+	};
+
+	mcu_uart0_pins_default: mcu-uart0-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (H37) WKUP_GPIO0_14.MCU_UART0_CTSn */
+			J784S4_WKUP_IOPAD(0x094, PIN_OUTPUT, 0) /* (K37) WKUP_GPIO0_15.MCU_UART0_RTSn */
+			J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (K38) WKUP_GPIO0_13.MCU_UART0_RXD */
+			J784S4_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (J37) WKUP_GPIO0_12.MCU_UART0_TXD */
+		>;
+	};
+
+	mcu_cpsw_pins_default: mcu-cpsw-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x02c, PIN_INPUT, 0) /* (A35) MCU_RGMII1_RD0 */
+			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (B36) MCU_RGMII1_RD1 */
+			J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (C36) MCU_RGMII1_RD2 */
+			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D36) MCU_RGMII1_RD3 */
+			J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (B37) MCU_RGMII1_RXC */
+			J784S4_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (C37) MCU_RGMII1_RX_CTL */
+			J784S4_WKUP_IOPAD(0x014, PIN_OUTPUT, 0) /* (D37) MCU_RGMII1_TD0 */
+			J784S4_WKUP_IOPAD(0x010, PIN_OUTPUT, 0) /* (D38) MCU_RGMII1_TD1 */
+			J784S4_WKUP_IOPAD(0x00c, PIN_OUTPUT, 0) /* (E37) MCU_RGMII1_TD2 */
+			J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E38) MCU_RGMII1_TD3 */
+			J784S4_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (E36) MCU_RGMII1_TXC */
+			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (C38) MCU_RGMII1_TX_CTL */
+		>;
+	};
+
+	mcu_mdio_pins_default: mcu-mdio-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A36) MCU_MDIO0_MDC */
+			J784S4_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (B35) MCU_MDIO0_MDIO */
+		>;
+	};
+
+	mcu_adc0_pins_default: mcu-adc0-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x0cc, PIN_INPUT, 0) /* (P36) MCU_ADC0_AIN0 */
+			J784S4_WKUP_IOPAD(0x0d0, PIN_INPUT, 0) /* (V36) MCU_ADC0_AIN1 */
+			J784S4_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (T34) MCU_ADC0_AIN2 */
+			J784S4_WKUP_IOPAD(0x0d8, PIN_INPUT, 0) /* (T36) MCU_ADC0_AIN3 */
+			J784S4_WKUP_IOPAD(0x0dc, PIN_INPUT, 0) /* (P34) MCU_ADC0_AIN4 */
+			J784S4_WKUP_IOPAD(0x0e0, PIN_INPUT, 0) /* (R37) MCU_ADC0_AIN5 */
+			J784S4_WKUP_IOPAD(0x0e4, PIN_INPUT, 0) /* (R33) MCU_ADC0_AIN6 */
+			J784S4_WKUP_IOPAD(0x0e8, PIN_INPUT, 0) /* (V38) MCU_ADC0_AIN7 */
+		>;
+	};
+
+	mcu_adc1_pins_default: mcu-adc1-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x0ec, PIN_INPUT, 0) /* (Y38) MCU_ADC1_AIN0 */
+			J784S4_WKUP_IOPAD(0x0f0, PIN_INPUT, 0) /* (Y34) MCU_ADC1_AIN1 */
+			J784S4_WKUP_IOPAD(0x0f4, PIN_INPUT, 0) /* (V34) MCU_ADC1_AIN2 */
+			J784S4_WKUP_IOPAD(0x0f8, PIN_INPUT, 0) /* (W37) MCU_ADC1_AIN3 */
+			J784S4_WKUP_IOPAD(0x0fc, PIN_INPUT, 0) /* (AA37) MCU_ADC1_AIN4 */
+			J784S4_WKUP_IOPAD(0x100, PIN_INPUT, 0) /* (W33) MCU_ADC1_AIN5 */
+			J784S4_WKUP_IOPAD(0x104, PIN_INPUT, 0) /* (U33) MCU_ADC1_AIN6 */
+			J784S4_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
+		>;
+	};
+
+	mcu_mcan0_pins_default: mcu-mcan0-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x050, PIN_OUTPUT, 0) /* (K33) MCU_MCAN0_TX */
+			J784S4_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (F38) MCU_MCAN0_RX */
+		>;
+	};
+
+	mcu_mcan1_pins_default: mcu-mcan1-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (H35) WKUP_GPIO0_4.MCU_MCAN1_TX */
+			J784S4_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (K36) WKUP_GPIO0_5.MCU_MCAN1_RX */
+		>;
+	};
+
+	mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x040, PIN_INPUT, 7) /* (J38) MCU_SPI0_D1.WKUP_GPIO0_69 */
+		>;
+	};
+
+	mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-default-pins {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x060, PIN_INPUT, 7) /* (J35) WKUP_GPIO0_2 */
+		>;
+	};
+};
+
+&wkup_pmx1 {
+	status = "okay";
+
+	pmic_irq_pins_default: pmic-irq-default-pins {
+		pinctrl-single,pins = <
+			/* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
+		>;
+	};
+};
+
+&wkup_pmx0 {
+	bootph-all;
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
+			J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
+			J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
+			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
+			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
+			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
+			J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
+			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
+			J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
+			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
+			J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
+		>;
+	};
+};
+
+&wkup_pmx1 {
+	bootph-all;
+	mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x004, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_ECC_FAIL */
+			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_RESET_OUT0 */
+		>;
+	};
+
+	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-default-pins {
+		bootph-all;
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (F32) MCU_OSPI1_CLK */
+			J784S4_WKUP_IOPAD(0x024, PIN_OUTPUT, 0) /* (G32) MCU_OSPI1_CSn0 */
+			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (E35) MCU_OSPI1_D0 */
+			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (D31) MCU_OSPI1_D1 */
+			J784S4_WKUP_IOPAD(0x01C, PIN_INPUT, 0) /* (G31) MCU_OSPI1_D2 */
+			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (F33) MCU_OSPI1_D3 */
+			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F31) MCU_OSPI1_DQS */
+			J784S4_WKUP_IOPAD(0x00C, PIN_INPUT, 0) /* (C31) MCU_OSPI1_LBCLKO */
+		>;
+	};
+};
+
+&wkup_uart0 {
+	/* Firmware usage */
+	status = "reserved";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_uart0_pins_default>;
+};
+
+&wkup_i2c0 {
+	bootph-all;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	eeprom@50 {
+		/* CAV24C256WE-GT3 */
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+
+	tps659413: pmic@48 {
+		compatible = "ti,tps6594-q1";
+		reg = <0x48>;
+		system-power-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&wkup_gpio0>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		ti,primary-pmic;
+		buck12-supply = <&vsys_3v3>;
+		buck3-supply = <&vsys_3v3>;
+		buck4-supply = <&vsys_3v3>;
+		buck5-supply = <&vsys_3v3>;
+		ldo1-supply = <&vsys_3v3>;
+		ldo2-supply = <&vsys_3v3>;
+		ldo3-supply = <&vsys_3v3>;
+		ldo4-supply = <&vsys_3v3>;
+
+		regulators {
+			bucka12: buck12 {
+				regulator-name = "vdd_ddr_1v1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka3: buck3 {
+				regulator-name = "vdd_ram_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka4: buck4 {
+				regulator-name = "vdd_io_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bucka5: buck5 {
+				regulator-name = "vdd_mcu_0v85";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa1: ldo1 {
+				regulator-name = "vdd_mcuio_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa2: ldo2 {
+				regulator-name = "vdd_mcuio_3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa3: ldo3 {
+				regulator-name = "vds_dll_0v8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldoa4: ldo4 {
+				regulator-name = "vda_mcu_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	tps62873a: regulator@40 {
+		compatible = "ti,tps62873";
+		reg = <0x40>;
+		bootph-pre-ram;
+		regulator-name = "VDD_CPU_AVS";
+		regulator-min-microvolt = <750000>;
+		regulator-max-microvolt = <1330000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	tps62873b: regulator@43 {
+		compatible = "ti,tps62873";
+		reg = <0x43>;
+		regulator-name = "VDD_CORE_0V8";
+		regulator-min-microvolt = <760000>;
+		regulator-max-microvolt = <840000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&mcu_uart0 {
+	bootph-all;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_uart0_pins_default>;
+};
+
+&main_uart8 {
+	bootph-all;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart8_pins_default>;
+};
+
+&ufs_wrapper {
+	status = "okay";
+};
+
+&fss {
+	bootph-all;
+	status = "okay";
+};
+
+&ospi0 {
+	bootph-all;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
+
+	flash@0 {
+		bootph-all;
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "ospi.tiboot3";
+				reg = <0x0 0x80000>;
+			};
+
+			partition@80000 {
+				label = "ospi.tispl";
+				reg = <0x80000 0x200000>;
+			};
+
+			partition@280000 {
+				label = "ospi.u-boot";
+				reg = <0x280000 0x400000>;
+			};
+
+			partition@680000 {
+				label = "ospi.env";
+				reg = <0x680000 0x40000>;
+			};
+
+			partition@6c0000 {
+				label = "ospi.env.backup";
+				reg = <0x6c0000 0x40000>;
+			};
+
+			partition@800000 {
+				label = "ospi.rootfs";
+				reg = <0x800000 0x37c0000>;
+			};
+
+			partition@3fc0000 {
+				bootph-all;
+				label = "ospi.phypattern";
+				reg = <0x3fc0000 0x40000>;
+			};
+		};
+	};
+};
+
+&ospi1 {
+	bootph-all;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+
+	flash@0 {
+		bootph-all;
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <40000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "qspi.tiboot3";
+				reg = <0x0 0x80000>;
+			};
+
+			partition@80000 {
+				label = "qspi.tispl";
+				reg = <0x80000 0x200000>;
+			};
+
+			partition@280000 {
+				label = "qspi.u-boot";
+				reg = <0x280000 0x400000>;
+			};
+
+			partition@680000 {
+				label = "qspi.env";
+				reg = <0x680000 0x40000>;
+			};
+
+			partition@6c0000 {
+				label = "qspi.env.backup";
+				reg = <0x6c0000 0x40000>;
+			};
+
+			partition@800000 {
+				label = "qspi.rootfs";
+				reg = <0x800000 0x37c0000>;
+			};
+
+			partition@3fc0000 {
+				bootph-all;
+				label = "qspi.phypattern";
+				reg = <0x3fc0000 0x40000>;
+			};
+		};
+
+	};
+};
+
+&main_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+
+	clock-frequency = <400000>;
+
+	exp1: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "PCIE1_2L_MODE_SEL", "PCIE1_4L_PERSTZ", "PCIE1_2L_RC_RSTZ",
+				  "PCIE1_2L_EP_RST_EN", "PCIE0_4L_MODE_SEL", "PCIE0_4L_PERSTZ",
+				  "PCIE0_4L_RC_RSTZ", "PCIE0_4L_EP_RST_EN", "PCIE1_4L_PRSNT#",
+				  "PCIE0_4L_PRSNT#", "CDCI1_OE1/OE4", "CDCI1_OE2/OE3",
+				  "AUDIO_MUX_SEL", "EXP_MUX2", "EXP_MUX3", "GESI_EXP_PHY_RSTZ";
+
+		p12-hog {
+			/* P12 - AUDIO_MUX_SEL */
+			gpio-hog;
+			gpios = <12 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "AUDIO_MUX_SEL";
+		};
+	};
+
+	exp2: gpio@22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "R_GPIO_RGMII1_RST", "ENET2_I2CMUX_SEL", "GPIO_USD_PWR_EN",
+				  "USBC_PWR_EN", "USBC_MODE_SEL1", "USBC_MODE_SEL0",
+				  "GPIO_LIN_EN", "R_CAN_STB", "CTRL_PM_I2C_OE#",
+				  "ENET2_EXP_PWRDN", "ENET2_EXP_SPARE2", "CDCI2_RSTZ",
+				  "USB2.0_MUX_SEL", "CANUART_MUX_SEL0", "CANUART_MUX2_SEL1",
+				  "CANUART_MUX1_SEL1", "ENET1_EXP_PWRDN", "ENET1_EXP_RESETZ",
+				  "ENET1_I2CMUX_SEL", "ENET1_EXP_SPARE2", "ENET2_EXP_RESETZ",
+				  "USER_INPUT1", "USER_LED1", "USER_LED2";
+
+		p13-hog {
+			/* P13 - CANUART_MUX_SEL0 */
+			gpio-hog;
+			gpios = <13 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "CANUART_MUX_SEL0";
+		};
+
+		p15-hog {
+			/* P15 - CANUART_MUX1_SEL1 */
+			gpio-hog;
+			gpios = <15 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "CANUART_MUX1_SEL1";
+		};
+	};
+};
+
+&main_i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c5_pins_default>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	exp5: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "CSI2_EXP_RSTZ", "CSI2_EXP_A_GPIO0",
+				  "CSI2_EXP_A_GPIO1", "CSI2_EXP_A_GPIO3",
+				  "CSI2_EXP_B_GPIO1", "CSI2_EXP_B_GPIO2",
+				  "CSI2_EXP_B_GPIO3", "CSI2_EXP_B_GPIO4";
+	};
+};
+
+&main_sdhci0 {
+	bootph-all;
+	/* eMMC */
+	status = "okay";
+	non-removable;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&main_sdhci1 {
+	bootph-all;
+	/* SD card */
+	status = "okay";
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	pinctrl-names = "default";
+	disable-wp;
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vdd_sd_dv>;
+};
+
+&main_gpio0 {
+	status = "okay";
+};
+
+&mcu_cpsw {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_cpsw_pins_default>;
+};
+
+&davinci_mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mdio_pins_default>;
+
+	mcu_phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
+
+&mcu_cpsw_port1 {
+	status = "okay";
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&mcu_phy0>;
+};
+
+&main_cpsw1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_cpsw2g_default_pins>;
+	status = "okay";
+};
+
+&main_cpsw1_mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_cpsw2g_mdio_default_pins>;
+	status = "okay";
+
+	main_cpsw1_phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
+
+&main_cpsw1_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&main_cpsw1_phy0>;
+	status = "okay";
+};
+
+&mailbox0_cluster0 {
+	status = "okay";
+	interrupts = <436>;
+
+	mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+
+	mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&mailbox0_cluster1 {
+	status = "okay";
+	interrupts = <432>;
+
+	mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+
+	mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&mailbox0_cluster2 {
+	status = "okay";
+	interrupts = <428>;
+
+	mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+
+	mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&mailbox0_cluster3 {
+	status = "okay";
+	interrupts = <424>;
+
+	mbox_main_r5fss2_core0: mbox-main-r5fss2-core0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+
+	mbox_main_r5fss2_core1: mbox-main-r5fss2-core1 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&mailbox0_cluster4 {
+	status = "okay";
+	interrupts = <420>;
+
+	mbox_c71_0: mbox-c71-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+
+	mbox_c71_1: mbox-c71-1 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&mailbox0_cluster5 {
+	status = "okay";
+	interrupts = <416>;
+
+	mbox_c71_2: mbox-c71-2 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+
+	mbox_c71_3: mbox-c71-3 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&mcu_r5fss0_core0 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
+	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
+			<&mcu_r5fss0_core0_memory_region>;
+};
+
+&mcu_r5fss0_core1 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core1>;
+	memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
+			<&mcu_r5fss0_core1_memory_region>;
+};
+
+&main_r5fss0_core0 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core0>;
+	memory-region = <&main_r5fss0_core0_dma_memory_region>,
+			<&main_r5fss0_core0_memory_region>;
+};
+
+&main_r5fss0_core1 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core1>;
+	memory-region = <&main_r5fss0_core1_dma_memory_region>,
+			<&main_r5fss0_core1_memory_region>;
+};
+
+&main_r5fss1_core0 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster2 &mbox_main_r5fss1_core0>;
+	memory-region = <&main_r5fss1_core0_dma_memory_region>,
+			<&main_r5fss1_core0_memory_region>;
+};
+
+&main_r5fss1_core1 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster2 &mbox_main_r5fss1_core1>;
+	memory-region = <&main_r5fss1_core1_dma_memory_region>,
+			<&main_r5fss1_core1_memory_region>;
+};
+
+&main_r5fss2_core0 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster3 &mbox_main_r5fss2_core0>;
+	memory-region = <&main_r5fss2_core0_dma_memory_region>,
+			<&main_r5fss2_core0_memory_region>;
+};
+
+&main_r5fss2_core1 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster3 &mbox_main_r5fss2_core1>;
+	memory-region = <&main_r5fss2_core1_dma_memory_region>,
+			<&main_r5fss2_core1_memory_region>;
+};
+
+&c71_0 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster4 &mbox_c71_0>;
+	memory-region = <&c71_0_dma_memory_region>,
+			<&c71_0_memory_region>;
+};
+
+&c71_1 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster4 &mbox_c71_1>;
+	memory-region = <&c71_1_dma_memory_region>,
+			<&c71_1_memory_region>;
+};
+
+&c71_2 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster5 &mbox_c71_2>;
+	memory-region = <&c71_2_dma_memory_region>,
+			<&c71_2_memory_region>;
+};
+
+&c71_3 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster5 &mbox_c71_3>;
+	memory-region = <&c71_3_dma_memory_region>,
+			<&c71_3_memory_region>;
+};
+
+&tscadc0 {
+	pinctrl-0 = <&mcu_adc0_pins_default>;
+	pinctrl-names = "default";
+	status = "okay";
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6 7>;
+	};
+};
+
+&tscadc1 {
+	pinctrl-0 = <&mcu_adc1_pins_default>;
+	pinctrl-names = "default";
+	status = "okay";
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6 7>;
+	};
+};
+
+&serdes_refclk {
+	status = "okay";
+	clock-frequency = <100000000>;
+};
+
+&dss {
+	status = "okay";
+	assigned-clocks = <&k3_clks 218 2>,
+			  <&k3_clks 218 5>,
+			  <&k3_clks 218 14>,
+			  <&k3_clks 218 18>;
+	assigned-clock-parents = <&k3_clks 218 3>,
+				 <&k3_clks 218 7>,
+				 <&k3_clks 218 16>,
+				 <&k3_clks 218 22>;
+};
+
+&serdes0 {
+	status = "okay";
+
+	serdes0_pcie1_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <2>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz0 1>, <&serdes_wiz0 2>;
+	};
+
+	serdes0_usb_link: phy@3 {
+		reg = <3>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+		resets = <&serdes_wiz0 4>;
+	};
+};
+
+&serdes_wiz0 {
+	status = "okay";
+};
+
+&usb_serdes_mux {
+	idle-states = <0>; /* USB0 to SERDES lane 3 */
+};
+
+&usbss0 {
+	status = "okay";
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	pinctrl-names = "default";
+	ti,vbus-divider;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "super-speed";
+	phys = <&serdes0_usb_link>;
+	phy-names = "cdns3,usb3-phy";
+};
+
+&serdes_wiz4 {
+	status = "okay";
+};
+
+&serdes4 {
+	status = "okay";
+	serdes4_dp_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <4>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_DP>;
+		resets = <&serdes_wiz4 1>, <&serdes_wiz4 2>,
+			 <&serdes_wiz4 3>, <&serdes_wiz4 4>;
+	};
+};
+
+&mhdp {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&dp0_pins_default>;
+	phys = <&serdes4_dp_link>;
+	phy-names = "dpphy";
+};
+
+&dss_ports {
+	/* DP */
+	port {
+		dpi0_out: endpoint {
+			remote-endpoint = <&dp0_in>;
+		};
+	};
+};
+
+&main_i2c4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c4_pins_default>;
+	clock-frequency = <400000>;
+
+	exp4: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&dp0_ports {
+	port@0 {
+		reg = <0>;
+
+		dp0_in: endpoint {
+			remote-endpoint = <&dpi0_out>;
+		};
+	};
+
+	port@4 {
+		reg = <4>;
+
+		dp0_out: endpoint {
+			remote-endpoint = <&dp0_connector_in>;
+		};
+	};
+};
+
+&mcu_mcan0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan0_pins_default>;
+	phys = <&transceiver0>;
+};
+
+&mcu_mcan1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan1_pins_default>;
+	phys = <&transceiver1>;
+};
+
+&main_mcan16 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan16_pins_default>;
+	phys = <&transceiver2>;
+};
+
+&main_mcan4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan4_pins_default>;
+	phys = <&transceiver3>;
+};
+
+&pcie1_rc {
+	status = "okay";
+	num-lanes = <2>;
+	reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes0_pcie1_link>;
+	phy-names = "pcie-phy";
+};
+
+&serdes1 {
+	status = "okay";
+
+	serdes1_pcie0_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <2>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz1 1>, <&serdes_wiz1 2>;
+	};
+};
+
+&serdes_wiz1 {
+	status = "okay";
+};
+
+&pcie0_rc {
+	status = "okay";
+	reset-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes1_pcie0_link>;
+	phy-names = "pcie-phy";
+};
+
+&k3_clks {
+	/* Confiure AUDIO_EXT_REFCLK1 pin as output */
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_ext_refclk1_pins_default>;
+};
+
+&main_i2c3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c3_pins_default>;
+	clock-frequency = <400000>;
+
+	exp3: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pcm3168a_1: audio-codec@44 {
+		compatible = "ti,pcm3168a";
+		reg = <0x44>;
+		#sound-dai-cells = <1>;
+		reset-gpios = <&exp3 0 GPIO_ACTIVE_LOW>;
+		clocks = <&audio_refclk1>;
+		clock-names = "scki";
+		VDD1-supply = <&vsys_3v3>;
+		VDD2-supply = <&vsys_3v3>;
+		VCCAD1-supply = <&vsys_5v0>;
+		VCCAD2-supply = <&vsys_5v0>;
+		VCCDA1-supply = <&vsys_5v0>;
+		VCCDA2-supply = <&vsys_5v0>;
+	};
+};
+
+&mcasp0 {
+	status = "okay";
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcasp0_pins_default>;
+	op-mode = <0>;          /* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	auxclk-fs-ratio = <256>;
+	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
+		0 0 0 1
+		2 0 0 0
+		0 0 0 0
+		0 0 0 0
+	>;
+};

-- 
2.45.1

[PATCH v3 6/9] arm64: dts: ti: Split k3-j784s4-j742s2-evm-common.dtsi

[Manorit Chawdhry]

k3-j784s4-j742s2-evm-common.dtsi will be included in k3-j742s2-evm.dts
at a later point so move j784s4 related stuff to k3-j784s4-evm.dts

Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts           | 49 ++++++++++++++++++++++
 .../boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi   | 42 -------------------
 2 files changed, 49 insertions(+), 42 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index e3730b2bca92..2543983b7fe7 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -5,4 +5,53 @@
  * EVM Board Schematics: https://www.ti.com/lit/zip/sprr458
  */
 
+/dts-v1/;
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-j784s4.dtsi"
 #include "k3-j784s4-j742s2-evm-common.dtsi"
+
+/ {
+	compatible = "ti,j784s4-evm", "ti,j784s4";
+	model = "Texas Instruments J784S4 EVM";
+
+	memory@80000000 {
+		device_type = "memory";
+		bootph-all;
+		/* 32G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+		      <0x00000008 0x80000000 0x00000007 0x80000000>;
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+
+		c71_3_dma_memory_region: c71-dma-memory@ab000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xab000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c71_3_memory_region: c71-memory@ab100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xab100000 0x00 0xf00000>;
+			no-map;
+		};
+	};
+};
+
+&mailbox0_cluster5 {
+	mbox_c71_3: mbox-c71-3 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&c71_3 {
+	status = "okay";
+	mboxes = <&mailbox0_cluster5 &mbox_c71_3>;
+	memory-region = <&c71_3_dma_memory_region>,
+			<&c71_3_memory_region>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
index ffa38f41679d..068ceed4ea15 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
@@ -4,17 +4,7 @@
  *
  * EVM Board Schematics: https://www.ti.com/lit/zip/sprr458
  */
-
-/dts-v1/;
-
-#include <dt-bindings/net/ti-dp83867.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "k3-j784s4.dtsi"
-
 / {
-	compatible = "ti,j784s4-evm", "ti,j784s4";
-	model = "Texas Instruments J784S4 EVM";
-
 	chosen {
 		stdout-path = "serial2:115200n8";
 	};
@@ -31,14 +21,6 @@ aliases {
 		ethernet1 = &main_cpsw1_port1;
 	};
 
-	memory@80000000 {
-		device_type = "memory";
-		bootph-all;
-		/* 32G RAM */
-		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
-		      <0x00000008 0x80000000 0x00000007 0x80000000>;
-	};
-
 	reserved_memory: reserved-memory {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -180,18 +162,6 @@ c71_2_memory_region: c71-memory@aa100000 {
 			reg = <0x00 0xaa100000 0x00 0xf00000>;
 			no-map;
 		};
-
-		c71_3_dma_memory_region: c71-dma-memory@ab000000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xab000000 0x00 0x100000>;
-			no-map;
-		};
-
-		c71_3_memory_region: c71-memory@ab100000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0xab100000 0x00 0xf00000>;
-			no-map;
-		};
 	};
 
 	evm_12v0: regulator-evm12v0 {
@@ -1133,11 +1103,6 @@ mbox_c71_2: mbox-c71-2 {
 		ti,mbox-rx = <0 0 0>;
 		ti,mbox-tx = <1 0 0>;
 	};
-
-	mbox_c71_3: mbox-c71-3 {
-		ti,mbox-rx = <2 0 0>;
-		ti,mbox-tx = <3 0 0>;
-	};
 };
 
 &mcu_r5fss0_core0 {
@@ -1217,13 +1182,6 @@ &c71_2 {
 			<&c71_2_memory_region>;
 };
 
-&c71_3 {
-	status = "okay";
-	mboxes = <&mailbox0_cluster5 &mbox_c71_3>;
-	memory-region = <&c71_3_dma_memory_region>,
-			<&c71_3_memory_region>;
-};
-
 &tscadc0 {
 	pinctrl-0 = <&mcu_adc0_pins_default>;
 	pinctrl-names = "default";

-- 
2.45.1

Re: [PATCH v3 6/9] arm64: dts: ti: Split k3-j784s4-j742s2-evm-common.dtsi

[Nishanth Menon]

On 22:40-20240731, Manorit Chawdhry wrote:
> k3-j784s4-j742s2-evm-common.dtsi will be included in k3-j742s2-evm.dts
> at a later point so move j784s4 related stuff to k3-j784s4-evm.dts

How about this:

Refactor J784s2-evm to a common file which uses the
superset device to allow reuse in j742s2-evm which uses the subset part.

Use a similar style commit message in other refactoring patches as well.

> 
> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-j784s4-evm.dts           | 49 ++++++++++++++++++++++
>  .../boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi   | 42 -------------------
>  2 files changed, 49 insertions(+), 42 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> index e3730b2bca92..2543983b7fe7 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> @@ -5,4 +5,53 @@
>   * EVM Board Schematics: https://www.ti.com/lit/zip/sprr458
>   */
>  
> +/dts-v1/;
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "k3-j784s4.dtsi"
>  #include "k3-j784s4-j742s2-evm-common.dtsi"
> +
> +/ {
> +	compatible = "ti,j784s4-evm", "ti,j784s4";
> +	model = "Texas Instruments J784S4 EVM";
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		bootph-all;
> +		/* 32G RAM */
> +		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
> +		      <0x00000008 0x80000000 0x00000007 0x80000000>;
I understand you are moving the nodes in and it is just copy paste, but
we have an opportunity to clean the nodes up a bit here.

Same as https://lore.kernel.org/all/20240807120629.3bo2cu3wlpkixwrp@flattered/

> +	};
> +
> +	reserved_memory: reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +
> +		c71_3_dma_memory_region: c71-dma-memory@ab000000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0xab000000 0x00 0x100000>;
> +			no-map;
> +		};
> +
> +		c71_3_memory_region: c71-memory@ab100000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0xab100000 0x00 0xf00000>;
> +			no-map;
> +		};
> +	};
> +};
> +
> +&mailbox0_cluster5 {
> +	mbox_c71_3: mbox-c71-3 {
> +		ti,mbox-rx = <2 0 0>;
> +		ti,mbox-tx = <3 0 0>;
> +	};
> +};
> +
> +&c71_3 {
> +	status = "okay";

Status comes last. I know that these coding standards are new, and it
takes a little getting used to and one wishes there was a linting tool
of some sort to make this easier.. but for now, eyes are the only way
out :(.


> +	mboxes = <&mailbox0_cluster5 &mbox_c71_3>;
> +	memory-region = <&c71_3_dma_memory_region>,
> +			<&c71_3_memory_region>;
> +};

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

[PATCH v3 7/9] dt-bindings: arm: ti: Add bindings for J742S2 SoCs and Boards

[Manorit Chawdhry]

Add devicetree bindings for J742S2 family of devices.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
 Documentation/devicetree/bindings/arm/ti/k3.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/ti/k3.yaml b/Documentation/devicetree/bindings/arm/ti/k3.yaml
index 4d9c5fbb4c26..074d6dc6092f 100644
--- a/Documentation/devicetree/bindings/arm/ti/k3.yaml
+++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml
@@ -143,6 +143,12 @@ properties:
               - ti,j722s-evm
           - const: ti,j722s
 
+      - description: K3 J742S2 SoC
+        items:
+          - enum:
+              - ti,j742s2-evm
+          - const: ti,j742s2
+
       - description: K3 J784s4 SoC
         items:
           - enum:

-- 
2.45.1

[PATCH v3 8/9] arm64: dts: ti: Introduce J742S2 SoC family

[Manorit Chawdhry]

This device is a subset of J784S4 and shares the same memory map and
thus the nodes are being reused from J784S4 to avoid duplication.

Here are some of the salient features of the J742S2 automotive grade
application processor:

The J742S2 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration in automotive, ADAS and industrial
applications requiring AI at the network edge. This SoC extends the K3
Jacinto 7 family of SoCs with focus on raising performance and
integration while providing interfaces, memory architecture and compute
performance for multi-sensor, high concurrency applications.

Some changes that this devices has from J784S4 are:
* 4x Cortex-A72 vs 8x Cortex-A72
* 3x C7x DSP vs 4x C7x DSP
* 4 port ethernet switch vs 8 port ethernet switch

( Refer Table 2-1 for Device comparison with J7AHP )
Link: https://www.ti.com/lit/pdf/spruje3 (TRM)
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j742s2-main.dtsi         | 45 ++++++++++
 arch/arm64/boot/dts/ti/k3-j742s2.dtsi              | 98 ++++++++++++++++++++++
 .../arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi |  5 +-
 3 files changed, 146 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j742s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j742s2-main.dtsi
new file mode 100644
index 000000000000..b320c27f7afe
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j742s2-main.dtsi
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Device Tree Source for J742S2 SoC Family
+ *
+ * TRM: https://www.ti.com/lit/pdf/spruje3
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+&c71_0 {
+	firmware-name = "j742s2-c71_0-fw";
+};
+
+&c71_1 {
+	firmware-name = "j742s2-c71_1-fw";
+};
+
+&c71_2 {
+	firmware-name = "j742s2-c71_2-fw";
+};
+
+&main_r5fss0_core0 {
+	firmware-name = "j742s2-main-r5f0_0-fw";
+};
+
+&main_r5fss0_core1 {
+	firmware-name = "j742s2-main-r5f0_1-fw";
+};
+
+&main_r5fss1_core0 {
+	firmware-name = "j742s2-main-r5f1_0-fw";
+};
+
+&main_r5fss1_core1 {
+	firmware-name = "j742s2-main-r5f1_1-fw";
+};
+
+&main_r5fss2_core0 {
+	firmware-name = "j742s2-main-r5f2_0-fw";
+};
+
+&main_r5fss2_core1 {
+	firmware-name = "j742s2-main-r5f2_1-fw";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j742s2.dtsi b/arch/arm64/boot/dts/ti/k3-j742s2.dtsi
new file mode 100644
index 000000000000..7a72f82f56d6
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j742s2.dtsi
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Device Tree Source for J742S2 SoC Family
+ *
+ * TRM: https://www.ti.com/lit/pdf/spruje3
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+#include "k3-j784s4-j742s2-common.dtsi"
+
+/ {
+	model = "Texas Instruments K3 J742S2 SoC";
+	compatible = "ti,j742s2";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0: cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a72";
+			reg = <0x000>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a72";
+			reg = <0x001>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a72";
+			reg = <0x002>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a72";
+			reg = <0x003>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+	};
+};
+
+#include "k3-j742s2-main.dtsi"
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi
index 958054ab1018..43fee57f0926 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi
@@ -1,8 +1,9 @@
 // SPDX-License-Identifier: GPL-2.0-only OR MIT
 /*
- * Device Tree Source for J784S4 SoC Family
+ * Device Tree Source for J784S4 and J742S2 SoC Family
  *
- * TRM (SPRUJ43 JULY 2022): https://www.ti.com/lit/zip/spruj52
+ * TRM (j784s4) (SPRUJ43 JULY 2022): https://www.ti.com/lit/zip/spruj52
+ * TRM (j742s2): https://www.ti.com/lit/pdf/spruje3
  *
  * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
  *

-- 
2.45.1

[PATCH v3 9/9] arm64: dts: ti: Add support for J742S2 EVM board

[Manorit Chawdhry]

J742S2 EVM board is designed for TI J742S2 SoC. It supports the following
interfaces:
* 16 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 Input Audio Jack, x1 Output Audio Jack
* x1 USB2.0 Hub with two Type A host and x1 USB 3.1 Type-C Port
* x1 4L PCIe connector
* x1 UHS-1 capable micro-SD card slot
* 512 Mbit OSPI flash, 1 Gbit Octal NAND flash, 512 Mbit QSPI flash,
  UFS flash.
* x6 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* x1 GESI expander, x2 Display connector
* x1 15-pin CSI header
* x6 MCAN instances

Link: https://www.ti.com/lit/ug/sprujd8/sprujd8.pdf (EVM user guide)
Link: https://www.ti.com/lit/zip/SPAC001 (Schematics)
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
---
 arch/arm64/boot/dts/ti/Makefile                    |  4 ++++
 arch/arm64/boot/dts/ti/k3-j742s2-evm.dts           | 26 ++++++++++++++++++++++
 .../boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi   |  3 ++-
 3 files changed, 32 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index e20b27ddf901..1bf645726a10 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -119,6 +119,9 @@ dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-pcie0-pcie1-ep.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-quad-port-eth-exp1.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-usxgmii-exp1-exp2.dtbo
 
+# Boards with J742S2 SoC
+dtb-$(CONFIG_ARCH_K3) += k3-j742s2-evm.dtb
+
 # Build time test only, enabled by CONFIG_OF_ALL_DTBS
 k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
 	k3-am625-beagleplay-csi2-ov5640.dtbo
@@ -240,3 +243,4 @@ DTC_FLAGS_k3-j721e-common-proc-board += -@
 DTC_FLAGS_k3-j721e-sk += -@
 DTC_FLAGS_k3-j721s2-common-proc-board += -@
 DTC_FLAGS_k3-j784s4-evm += -@
+DTC_FLAGS_k3-j742s2-evm += -@
diff --git a/arch/arm64/boot/dts/ti/k3-j742s2-evm.dts b/arch/arm64/boot/dts/ti/k3-j742s2-evm.dts
new file mode 100644
index 000000000000..ac683bcbfe97
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j742s2-evm.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/*
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * EVM Board Schematics: https://www.ti.com/lit/zip/SPAC001
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-j742s2.dtsi"
+#include "k3-j784s4-j742s2-evm-common.dtsi"
+
+/ {
+	model = "Texas Instruments J742S2 EVM";
+	compatible = "ti,j742s2-evm", "ti,j742s2";
+
+	memory@80000000 {
+		device_type = "memory";
+		bootph-all;
+		/* 16G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+		      <0x00000008 0x80000000 0x00000003 0x80000000>;
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
index 068ceed4ea15..a7bb1857b4e8 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
@@ -2,7 +2,8 @@
 /*
  * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
  *
- * EVM Board Schematics: https://www.ti.com/lit/zip/sprr458
+ * EVM Board Schematics(j784s4): https://www.ti.com/lit/zip/sprr458
+ * EVM Board Schematics(j742s2): https://www.ti.com/lit/zip/SPAC001
  */
 / {
 	chosen {

-- 
2.45.1

Re: [PATCH v3 9/9] arm64: dts: ti: Add support for J742S2 EVM board

[Beleswar Prasad Padhi]

Hi Manorit,

On 31/07/24 22:40, Manorit Chawdhry wrote:
> J742S2 EVM board is designed for TI J742S2 SoC. It supports the following
> interfaces:
> * 16 GB DDR4 RAM
> * x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
> * x1 Input Audio Jack, x1 Output Audio Jack
> * x1 USB2.0 Hub with two Type A host and x1 USB 3.1 Type-C Port
> * x1 4L PCIe connector
> * x1 UHS-1 capable micro-SD card slot
> * 512 Mbit OSPI flash, 1 Gbit Octal NAND flash, 512 Mbit QSPI flash,
>    UFS flash.
> * x6 UART through UART-USB bridge
> * XDS110 for onboard JTAG debug using USB
> * Temperature sensors, user push buttons and LEDs
> * x1 GESI expander, x2 Display connector
> * x1 15-pin CSI header
> * x6 MCAN instances
>
> Link: https://www.ti.com/lit/ug/sprujd8/sprujd8.pdf (EVM user guide)
> Link: https://www.ti.com/lit/zip/SPAC001 (Schematics)
> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>


For series,
Reviewed-By: Beleswar Padhi <b-padhi@ti.com>

> ---
>   arch/arm64/boot/dts/ti/Makefile                    |  4 ++++
>   arch/arm64/boot/dts/ti/k3-j742s2-evm.dts           | 26 ++++++++++++++++++++++
>   .../boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi   |  3 ++-
>   3 files changed, 32 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index e20b27ddf901..1bf645726a10 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -119,6 +119,9 @@ dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-pcie0-pcie1-ep.dtbo
>   dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-quad-port-eth-exp1.dtbo
>   dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-usxgmii-exp1-exp2.dtbo
>   
> +# Boards with J742S2 SoC
> +dtb-$(CONFIG_ARCH_K3) += k3-j742s2-evm.dtb
> +
>   # Build time test only, enabled by CONFIG_OF_ALL_DTBS
>   k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
>   	k3-am625-beagleplay-csi2-ov5640.dtbo
> @@ -240,3 +243,4 @@ DTC_FLAGS_k3-j721e-common-proc-board += -@
>   DTC_FLAGS_k3-j721e-sk += -@
>   DTC_FLAGS_k3-j721s2-common-proc-board += -@
>   DTC_FLAGS_k3-j784s4-evm += -@
> +DTC_FLAGS_k3-j742s2-evm += -@
> diff --git a/arch/arm64/boot/dts/ti/k3-j742s2-evm.dts b/arch/arm64/boot/dts/ti/k3-j742s2-evm.dts
> new file mode 100644
> index 000000000000..ac683bcbfe97
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-j742s2-evm.dts
> @@ -0,0 +1,26 @@
> +// SPDX-License-Identifier: GPL-2.0-only OR MIT
> +/*
> + * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
> + *
> + * EVM Board Schematics: https://www.ti.com/lit/zip/SPAC001
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include "k3-j742s2.dtsi"
> +#include "k3-j784s4-j742s2-evm-common.dtsi"
> +
> +/ {
> +	model = "Texas Instruments J742S2 EVM";
> +	compatible = "ti,j742s2-evm", "ti,j742s2";
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		bootph-all;
> +		/* 16G RAM */
> +		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
> +		      <0x00000008 0x80000000 0x00000003 0x80000000>;
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
> index 068ceed4ea15..a7bb1857b4e8 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
> @@ -2,7 +2,8 @@
>   /*
>    * Copyright (C) 2022-2024 Texas Instruments Incorporated - https://www.ti.com/
>    *
> - * EVM Board Schematics: https://www.ti.com/lit/zip/sprr458
> + * EVM Board Schematics(j784s4): https://www.ti.com/lit/zip/sprr458
> + * EVM Board Schematics(j742s2): https://www.ti.com/lit/zip/SPAC001
>    */
>   / {
>   	chosen {
>

Re: [PATCH v3 9/9] arm64: dts: ti: Add support for J742S2 EVM board

[Nishanth Menon]

On 15:11-20240807, Beleswar Prasad Padhi wrote:
> Hi Manorit,
> 
> On 31/07/24 22:40, Manorit Chawdhry wrote:
> > J742S2 EVM board is designed for TI J742S2 SoC. It supports the following
> > interfaces:
> > * 16 GB DDR4 RAM
> > * x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
> > * x1 Input Audio Jack, x1 Output Audio Jack
> > * x1 USB2.0 Hub with two Type A host and x1 USB 3.1 Type-C Port
> > * x1 4L PCIe connector
> > * x1 UHS-1 capable micro-SD card slot
> > * 512 Mbit OSPI flash, 1 Gbit Octal NAND flash, 512 Mbit QSPI flash,
> >    UFS flash.
> > * x6 UART through UART-USB bridge
> > * XDS110 for onboard JTAG debug using USB
> > * Temperature sensors, user push buttons and LEDs
> > * x1 GESI expander, x2 Display connector
> > * x1 15-pin CSI header
> > * x6 MCAN instances
> > 
> > Link: https://www.ti.com/lit/ug/sprujd8/sprujd8.pdf (EVM user guide)
> > Link: https://www.ti.com/lit/zip/SPAC001 (Schematics)
> > Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
> 
> 
> For series,
> Reviewed-By: Beleswar Padhi <b-padhi@ti.com>

Please follow the convention - if you are acking the series, reply to
the cover-letter such that tools like b4 can pick it up, else this ack
belongs to the current patch.

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH v3 9/9] arm64: dts: ti: Add support for J742S2 EVM board

[Nishanth Menon]

On 15:11-20240807, Beleswar Prasad Padhi wrote:
> For series,
> Reviewed-By: Beleswar Padhi <b-padhi@ti.com>
[...]
> > +/ {
> > +	model = "Texas Instruments J742S2 EVM";
> > +	compatible = "ti,j742s2-evm", "ti,j742s2";
> > +
> > +	memory@80000000 {
> > +		device_type = "memory";
> > +		bootph-all;
> > +		/* 16G RAM */
> > +		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
> > +		      <0x00000008 0x80000000 0x00000003 0x80000000>;

Sigh.. https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/dts-coding-style.rst#n117

1. "compatible" <- not present
2. "reg" <- present
3. "ranges" <- not present
4. Standard/common properties (defined by common bindings, e.g. without
   vendor-prefixes) <- bootph-all and device_type
5. Vendor-specific properties -> not present
6. "status" (if applicable) -> not present
7. Child nodes, where each node is preceded with a blank line -> not
present

So:

	/* 16G RAM */
	reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
	      <0x00000008 0x80000000 0x00000003 0x80000000>;
	device_type = "memory";
	bootph-all;

??

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH v3 0/9] Introduce J742S2 SoC and EVM

[Nishanth Menon]

On 22:40-20240731, Manorit Chawdhry wrote:
> The series adds support for J742S2 family of SoCs. Also adds J742S2 EVM
> Support and re-uses most of the stuff from the superset device J784s4.
> 
> It initially cleans up the J784s4 SoC files so that they can be
> re-usable for j742s2 by introducing -common files. Next it cleans up the
> EVM files for j784s4 in a similar way and then goes about adding the
> support for j742s2.
> 
> Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
> ---
> Changes in v3:
> * Nishanth
> - Update copyright string
> - Add TRM link in SoC file.
> - Refactor to split out common soc support between j742s2 and j784s4
> 
> - Add DTC_FLAGS as well for j742s2
> - Link to v2: https://lore.kernel.org/r/20240730-b4-upstream-j742s2-v2-0-6aedf892156c@ti.com
> 
> ---
> Manorit Chawdhry (9):
>       arm64: dts: ti: Move j784s4-{} include files to j784s4-j742s2-{}-common.dtsi
>       arm64: dts: ti: Move k3-j784s4.dtsi to k3-j784s4-j742s2-common.dtsi
>       arm64: dts: ti: Split k3-j784s4-j742s2-common.dtsi
>       arm64: dts: ti: Split k3-j784s4-j742s2-main-common.dtsi

The above 4 patches can be merged into a single patch under SoC
refactoring.

>       arm64: dts: ti: Move k3-j784s4-evm.dts to k3-j784s4-j742s2-evm-common.dtsi
>       arm64: dts: ti: Split k3-j784s4-j742s2-evm-common.dtsi

The above two patches can be squashed to be a single patch for evm
refactoring.

>       dt-bindings: arm: ti: Add bindings for J742S2 SoCs and Boards
>       arm64: dts: ti: Introduce J742S2 SoC family
>       arm64: dts: ti: Add support for J742S2 EVM board

Also it is not clear how cpsw/serdes and pcie changes are handled
here.

> 
>  Documentation/devicetree/bindings/arm/ti/k3.yaml   |    6 +
>  arch/arm64/boot/dts/ti/Makefile                    |    4 +
>  arch/arm64/boot/dts/ti/k3-j742s2-evm.dts           |   26 +
>  arch/arm64/boot/dts/ti/k3-j742s2-main.dtsi         |   45 +
>  arch/arm64/boot/dts/ti/k3-j742s2.dtsi              |   98 +
>  arch/arm64/boot/dts/ti/k3-j784s4-evm.dts           | 1422 +---------
>  .../arm64/boot/dts/ti/k3-j784s4-j742s2-common.dtsi |  150 ++
>  .../boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi   | 1436 ++++++++++
>  .../boot/dts/ti/k3-j784s4-j742s2-main-common.dtsi  | 2772 ++++++++++++++++++++
>  ...tsi => k3-j784s4-j742s2-mcu-wakeup-common.dtsi} |    2 +-
>  ...l.dtsi => k3-j784s4-j742s2-thermal-common.dtsi} |    0
>  arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi         | 2764 -------------------
>  arch/arm64/boot/dts/ti/k3-j784s4.dtsi              |  135 +-
>  13 files changed, 4540 insertions(+), 4320 deletions(-)
> ---
> base-commit: cd19ac2f903276b820f5d0d89de0c896c27036ed
> change-id: 20240620-b4-upstream-j742s2-7ba652091550
> 
> Best regards,
> -- 
> Manorit Chawdhry <m-chawdhry@ti.com>
> 

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D