* Re: [PATCH 3/9] firmware: imx: ele: Add API functions for OCOTP fuse access
From: Frank Li @ 2026-06-16 20:05 UTC (permalink / raw)
To: Frieder Schrempf
Cc: Frieder Schrempf, Pankaj Gupta, Srinivas Kandagatla, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Frank Li, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, Shawn Guo, devicetree,
imx, linux-arm-kernel, linux-kernel
In-Reply-To: <cea74ed4-1003-419e-8da3-1c62b1ace726@kontron.de>
On Tue, Jun 16, 2026 at 07:59:54PM +0200, Frieder Schrempf wrote:
> On 16.06.26 17:36, Frank Li wrote:
> > On Tue, Jun 16, 2026 at 01:52:18PM +0200, Frieder Schrempf wrote:
> >> From: Frieder Schrempf <frieder.schrempf@kontron.de>
> >>
> >> The ELE S400 API provides read and write access to the OCOTP fuse
> >> registers. This adds the necessary API functions imx_se_read_fuse()
> >> and imx_se_write_fuse() to be used by other drivers such as the
> >> OCOTP S400 NVMEM driver.
> >>
> >> This is ported from the downstream vendor kernel.
> >>
> >> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
> >> ---
> >> drivers/firmware/imx/ele_base_msg.c | 122 ++++++++++++++++++++++++++++++++++++
> >> drivers/firmware/imx/ele_base_msg.h | 6 ++
> >> include/linux/firmware/imx/se_api.h | 3 +
> >> 3 files changed, 131 insertions(+)
> >>
> > ...
> >> +++ b/include/linux/firmware/imx/se_api.h
> >> @@ -11,4 +11,7 @@
> >> #define SOC_ID_OF_IMX8ULP 0x084d
> >> #define SOC_ID_OF_IMX93 0x9300
> >>
> >> +int imx_se_read_fuse(void *se_if_data, uint16_t fuse_id, u32 *value);
> >> +int imx_se_write_fuse(void *se_if_data, uint16_t fuse_id, u32 value);
> >> +
> >
> > This API should implement in fuse drivers. Other consume should use standard
> > fuse API to get value. If put here, it may bypass fuse driver.
>
> The reason this is here, is the downstream implementation in linux-imx
> and the current code organization.
Downstream may not good enough, sometime, it is quick solution.
> I thought there is some good reason
> to have shared functions and it looks like Pankaj structured it like
> this so all API functions live in ele_base_msg.c and the internal
> structs and defines in ele_base_msg.h and se_ctrl.h are not exposed to
> other drivers.
>
> If I would move this into imx-ocotp-ele.c, then I would also need to
> change how the code is organized and make the internal se_api functions
> exposed to other drivers. I don't know if that is really a good idea.
>
> I get your point but it looks like this contradicts the intention of
> having a clean API in the firmware driver.
You can refer imx-ocotp-scu.c, structure should be similar, only difference
is that lower transfer APIs.
Frank
^ permalink raw reply
* [PATCH v1 0/8] arm64: dts: qcom: shikra: Enable audio on EVK boards
From: Mohammad Rafi Shaik @ 2026-06-16 20:13 UTC (permalink / raw)
To: Srinivas Kandagatla, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-sound, linux-arm-msm, devicetree, linux-kernel
This series enables the Shikra audio path on EVK targets by adding the QAIF
CPU endpoint, GPR/APM/PRM services, SoundWire and LPASS macro nodes, and
board-level sound card wiring for CQM, CQS and IQS variants.
The series is based on linux-next plus the posted Shikra dependency stack
(clock/controller, bindings and ASoC dependencies listed in prerequisite
patches below).
Patch split:
- 1-4: SoC-level audio nodes in shikra.dtsi (kept disabled)
- 5-7: board-level enablement for CQM/CQS/IQS EVKs
- 8: arm64 defconfig updates for QAIF and WSA885X-I2C
Mohammad Rafi Shaik (8):
ASoC: dt-bindings: qcom,apr: Add modem_apps GLINK channel for shikra
arm64: dts: qcom: shikra: Add QAIF CPU node for audio
arm64: dts: qcom: shikra: Add gpr node
arm64: dts: qcom: shikra: Add soundwire and macro nodes
arm64: dts: qcom: shikra-cqm-evk: Enable sound card support
arm64: dts: qcom: shikra-cqs-evk: Enable sound card support
arm64: dts: qcom: shikra-iqs-evk: Enable sound card support
arm64: defconfig: Enable Qualcomm QAIF and WSA885X-I2C drivers
.../bindings/soc/qcom/qcom,apr.yaml | 4 +-
arch/arm64/boot/dts/qcom/shikra-cqm-evk.dts | 222 +++++++++++++++
arch/arm64/boot/dts/qcom/shikra-cqm-som.dtsi | 5 +
arch/arm64/boot/dts/qcom/shikra-cqs-evk.dts | 149 ++++++++++
arch/arm64/boot/dts/qcom/shikra-iqs-evk.dts | 143 ++++++++++
arch/arm64/boot/dts/qcom/shikra.dtsi | 256 ++++++++++++++++++
arch/arm64/configs/defconfig | 2 +
7 files changed, 780 insertions(+), 1 deletion(-)
base-commit: abe651837cb394f76d738a7a747322fca3bf17ba
prerequisite-patch-id: 59bb0a7828e41f546f734f127d81da83c0adcda9
prerequisite-patch-id: 197da6bcb15cadc47869dba88c8020987b25c335
prerequisite-patch-id: 8ec9c1eb03f052ae232ed54117abed38672c23f6
prerequisite-patch-id: 350db4f4bcdfc0fad9ed57cd5b1723f85ad44f5d
prerequisite-patch-id: e80ea7940b9817449cec21afa6e9e443e007166f
prerequisite-patch-id: 80d8ab865b7b0663c5b2878b45b55e2e4fde9c19
prerequisite-patch-id: 8e645e1c6ad6182de4813a726c293654324de1df
prerequisite-patch-id: f6781d2cf0829ccb32f1400623c95739972f2ee2
prerequisite-patch-id: 2acc300a68ed8c5364fb5f2f7d28fc0d56ab07bf
prerequisite-patch-id: 2357cac636e019eaf14d6a493a1c72bca56fe405
prerequisite-patch-id: 2885f299e711582da312ca9d13983d296a3dd5dc
prerequisite-patch-id: 91af5f3c01e766a53ce8de69aa21847a2d6bbbf8
prerequisite-patch-id: 39475cddaf673b2cbbae703165a782916f199885
prerequisite-patch-id: 6f7f265abfbdffdc0a1fdc5a7e08929e4eec5b7a
prerequisite-patch-id: b5d7f75df02fde56181f576a936baf09d0a72276
prerequisite-patch-id: 3ce52e07ae57139c2e2b71a29ed7d7250f6fcc87
prerequisite-patch-id: 7d92e5a301d09616840e54dc9e4a81f30a64383c
prerequisite-patch-id: 003035cc99f02794043818256ba0ef657872d511
prerequisite-patch-id: 5d23c938843176de2a02987d2832f31fe5df7fcf
prerequisite-patch-id: 430488f50f36039338965ab1fc28d83f02dbc9fd
prerequisite-patch-id: 359ddad8a3fb36f171c96da5ce5ffacd7dd63e8f
prerequisite-patch-id: a98885b9d0e0655bb3161dc2c31fd92a844a5e4e
prerequisite-patch-id: 80aead6484e36f52cb6cc7fd7d9e0326d8296860
prerequisite-patch-id: 2f1bd3efac328030dd8efe28fb95f84603868043
prerequisite-patch-id: 047b4fb1894b92109aa7afcebd7d5c7988ec5379
prerequisite-patch-id: 99977ae9253a961b85331b9808c1feff0c2cc38e
prerequisite-patch-id: 9e3edab83e9fc008b2dc254fb3b548ddd8f8b5f8
prerequisite-patch-id: a7706e25f5951ec41e6b662c1704df8d20662d77
prerequisite-patch-id: d13035abab3ff342753f5bf87b53bbf06a02c6a1
prerequisite-patch-id: 4d40e704139dc4b0ec2529c49f096d86a4e4dc5f
--
2.34.1
^ permalink raw reply
* [PATCH v1 1/8] ASoC: dt-bindings: qcom,apr: Add modem_apps GLINK channel for shikra
From: Mohammad Rafi Shaik @ 2026-06-16 20:13 UTC (permalink / raw)
To: Srinivas Kandagatla, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-sound, linux-arm-msm, devicetree, linux-kernel
In-Reply-To: <20260616201315.2565115-1-mohammad.rafi.shaik@oss.qualcomm.com>
Add support for the modem_apps GLINK channel on Shikra, as audio
processing is handled through the modem DSP.
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
---
Documentation/devicetree/bindings/soc/qcom/qcom,apr.yaml | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.yaml
index e51acdcaafaf..01250b556985 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,apr.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,apr.yaml
@@ -120,7 +120,9 @@ allOf:
properties:
qcom,glink-channels:
items:
- - const: adsp_apps
+ - enum:
+ - adsp_apps
+ - modem_apps
power-domains: false
else:
properties:
--
2.34.1
^ permalink raw reply related
* [PATCH v1 2/8] arm64: dts: qcom: shikra: Add QAIF CPU node for audio
From: Mohammad Rafi Shaik @ 2026-06-16 20:13 UTC (permalink / raw)
To: Srinivas Kandagatla, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-sound, linux-arm-msm, devicetree, linux-kernel,
Harendra Gautam
In-Reply-To: <20260616201315.2565115-1-mohammad.rafi.shaik@oss.qualcomm.com>
Add the QAIF CPU endpoint in shikra.dtsi so board files can connect LPASS
front-end links to backend codecs.
Describe the MMIO region, interrupt, IOMMU mapping and required clocks for
the QAIF block. Keep the node disabled at SoC level; board dts files enable
and consume it in subsequent patches.
Co-developed-by: Harendra Gautam <harendra.gautam@oss.qualcomm.com>
Signed-off-by: Harendra Gautam <harendra.gautam@oss.qualcomm.com>
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/shikra.dtsi | 46 ++++++++++++++++++++++++++++
1 file changed, 46 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/shikra.dtsi b/arch/arm64/boot/dts/qcom/shikra.dtsi
index bc4ad2bcbbec..e58c87fc8cb0 100644
--- a/arch/arm64/boot/dts/qcom/shikra.dtsi
+++ b/arch/arm64/boot/dts/qcom/shikra.dtsi
@@ -2017,6 +2017,52 @@ dispcc: clock-controller@5f00000 {
#power-domain-cells = <1>;
};
+ qaif_cpu: audio@a000000 {
+ compatible = "qcom,shikra-qaif-cpu";
+ reg = <0x0 0x0a000000 0x0 0x20000>;
+
+ interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH 0>;
+
+ clocks = <&gcc GCC_LPASS_CONFIG_CLK>,
+ <&gcc GCC_LPASS_CORE_AXIM_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_AUD_DMA_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_AUD_DMA_MEM_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_BUS_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_AIF_IF0_EBIT_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_AIF_IF0_IBIT_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_AIF_IF1_EBIT_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_AIF_IF1_IBIT_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_AIF_IF2_EBIT_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_AIF_IF2_IBIT_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_AIF_IF3_EBIT_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_AIF_IF3_IBIT_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_EXT_MCLKA_OUT_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_EXT_MCLKB_OUT_CLK>;
+ clock-names = "lpass_config_clk",
+ "lpass_core_axim_clk",
+ "aud_dma_clk",
+ "aud_dma_mem_clk",
+ "bus_clk",
+ "aif_if0_ebit_clk",
+ "aif_if0_ibit_clk",
+ "aif_if1_ebit_clk",
+ "aif_if1_ibit_clk",
+ "aif_if2_ebit_clk",
+ "aif_if2_ibit_clk",
+ "aif_if3_ebit_clk",
+ "aif_if3_ibit_clk",
+ "ext_mclka_clk",
+ "ext_mclkb_clk";
+
+ iommus = <&apps_smmu 0x1c0 0x0>;
+
+ #sound-dai-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+
audiocorecc: clock-controller@a0a0000 {
compatible = "qcom,shikra-cqm-audiocorecc";
reg = <0x0 0x0a0a0000 0x0 0x10000>,
--
2.34.1
^ permalink raw reply related
* [PATCH v1 3/8] arm64: dts: qcom: shikra: Add gpr node
From: Mohammad Rafi Shaik @ 2026-06-16 20:13 UTC (permalink / raw)
To: Srinivas Kandagatla, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-sound, linux-arm-msm, devicetree, linux-kernel,
Pratyush Meduri
In-Reply-To: <20260616201315.2565115-1-mohammad.rafi.shaik@oss.qualcomm.com>
Add GPR(Generic Pack router) node along with
APM(Audio Process Manager) and PRM(Proxy resource
Manager) audio services.
Co-developed-by: Pratyush Meduri <mpratyus@qti.qualcomm.com>
Signed-off-by: Pratyush Meduri <mpratyus@qti.qualcomm.com>
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/shikra.dtsi | 39 ++++++++++++++++++++++++++++
1 file changed, 39 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/shikra.dtsi b/arch/arm64/boot/dts/qcom/shikra.dtsi
index e58c87fc8cb0..3df09cfd17a4 100644
--- a/arch/arm64/boot/dts/qcom/shikra.dtsi
+++ b/arch/arm64/boot/dts/qcom/shikra.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/clock/qcom,shikra-audiocorecc.h>
#include <dt-bindings/clock/qcom,shikra-gcc.h>
+#include <dt-bindings/firmware/qcom,scm.h>
#include <dt-bindings/interconnect/qcom,icc.h>
#include <dt-bindings/interconnect/qcom,osm-l3.h>
#include <dt-bindings/dma/qcom-gpi.h>
@@ -15,6 +16,8 @@
#include <dt-bindings/interconnect/qcom,shikra.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,gpr.h>
+#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
#include <dt-bindings/thermal/thermal.h>
/ {
@@ -1851,6 +1854,42 @@ glink-edge {
mboxes = <&apcs_glb 12>;
qcom,remote-pid = <1>;
label = "mpss";
+
+ gpr: gpr {
+ compatible = "qcom,gpr";
+ qcom,glink-channels = "modem_apps";
+ qcom,domain = <GPR_DOMAIN_ID_MODEM>;
+ qcom,intents = <200 20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ q6apm: service@1 {
+ compatible = "qcom,q6apm";
+ reg = <GPR_APM_MODULE_IID>;
+ #sound-dai-cells = <0>;
+
+ q6apmbedai: bedais {
+ compatible = "qcom,q6apm-lpass-dais";
+ #sound-dai-cells = <1>;
+ };
+
+ q6apmdai: dais {
+ compatible = "qcom,q6apm-dais";
+ qcom,vmid = <QCOM_SCM_VMID_LPASS
+ QCOM_SCM_VMID_MSS_MSA>;
+ };
+ };
+
+ q6prm: service@2 {
+ compatible = "qcom,q6prm";
+ reg = <GPR_PRM_MODULE_IID>;
+
+ q6prmcc: clock-controller {
+ compatible = "qcom,q6prm-lpass-clocks";
+ #clock-cells = <2>;
+ };
+ };
+ };
};
};
--
2.34.1
^ permalink raw reply related
* [PATCH v1 4/8] arm64: dts: qcom: shikra: Add soundwire and macro nodes
From: Mohammad Rafi Shaik @ 2026-06-16 20:13 UTC (permalink / raw)
To: Srinivas Kandagatla, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-sound, linux-arm-msm, devicetree, linux-kernel
In-Reply-To: <20260616201315.2565115-1-mohammad.rafi.shaik@oss.qualcomm.com>
Add SoC-level SoundWire masters and LPASS RX/VA macro nodes, along with
DMIC and SWR pinctrl states required by the audio data path.
Keep these nodes disabled in shikra.dtsi so board dts files can selectively
enable and configure them.
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/shikra.dtsi | 171 +++++++++++++++++++++++++++
1 file changed, 171 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/shikra.dtsi b/arch/arm64/boot/dts/qcom/shikra.dtsi
index 3df09cfd17a4..0ed73b948588 100644
--- a/arch/arm64/boot/dts/qcom/shikra.dtsi
+++ b/arch/arm64/boot/dts/qcom/shikra.dtsi
@@ -833,6 +833,70 @@ rclk-pins {
bias-bus-hold;
};
};
+
+ dmic01_default: dmic01-default-state {
+ clk-pins {
+ pins = "gpio96";
+ function = "dmic";
+ drive-strength = <8>;
+ output-high;
+ };
+
+ data-pins {
+ pins = "gpio97";
+ function = "dmic";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ dmic23_default: dmic23-default-state {
+ clk-pins {
+ pins = "gpio98";
+ function = "dmic";
+ drive-strength = <8>;
+ output-high;
+ };
+
+ data-pins {
+ pins = "gpio99";
+ function = "dmic";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ tx_swr_active: tx-swr-active-state {
+ clk-pins {
+ pins = "gpio105";
+ function = "swr0_tx";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio106";
+ function = "swr0_tx";
+ drive-strength = <8>;
+ bias-bus-hold;
+ };
+ };
+
+ rx_swr_active: rx-swr-active-state {
+ clk-pins {
+ pins = "gpio107";
+ function = "swr0_rx";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio108", "gpio109";
+ function = "swr0_rx";
+ drive-strength = <8>;
+ bias-bus-hold;
+ };
+ };
};
pmu@c91000 {
@@ -2114,6 +2178,113 @@ audiocorecc: clock-controller@a0a0000 {
status = "disabled";
};
+ rxmacro: codec@a040000 {
+ compatible = "qcom,shikra-lpass-rx-macro";
+ reg = <0x0 0x0a040000 0x0 0x1000>;
+
+ pinctrl-0 = <&rx_swr_active>;
+ pinctrl-names = "default";
+
+ clocks = <&audiocorecc AUDIO_CORE_CC_RX_MCLK_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_RX_MCLK_2X_CLK>,
+ <&vamacro>;
+ clock-names = "mclk",
+ "npl",
+ "fsgen";
+
+ #clock-cells = <0>;
+ clock-output-names = "mclk";
+ #sound-dai-cells = <1>;
+ status = "disabled";
+ };
+
+ swr0: soundwire@a060000 {
+ compatible = "qcom,soundwire-v3.1.0";
+ reg = <0x0 0x0a060000 0x0 0x10000>;
+ qcom,swr-master-ee-val = <0>;
+
+ interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH 0>;
+
+ clocks = <&rxmacro>;
+ clock-names = "iface";
+
+ label = "RX";
+ qcom,din-ports = <0>;
+ qcom,dout-ports = <5>;
+
+ resets = <&audiocorecc AUDIO_CORE_CSR_RX_SWR_CGCR>;
+ reset-names = "swr_audio_cgcr";
+
+ qcom,ports-sinterval-low = /bits/ 8 <0x03 0x1f 0x1f 0x07 0x00>;
+ qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0b 0x01 0x00>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
+ qcom,ports-hstart = /bits/ 8 <0xff 0x03 0xff 0xff 0xff>;
+ qcom,ports-hstop = /bits/ 8 <0xff 0x06 0xff 0xff 0xff>;
+ qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xff 0x00 0x01 0xff 0xff>;
+ qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0x00>;
+ qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
+
+ #sound-dai-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ vamacro: codec@a078000 {
+ compatible = "qcom,shikra-lpass-va-macro";
+ reg = <0x0 0x0a078000 0x0 0x2000>;
+
+ pinctrl-0 = <&tx_swr_active>;
+ pinctrl-names = "default";
+
+ clocks = <&audiocorecc AUDIO_CORE_CC_TX_MCLK_CLK>,
+ <&audiocorecc AUDIO_CORE_CC_TX_MCLK_2X_CLK>;
+ clock-names = "mclk",
+ "npl";
+
+ #clock-cells = <0>;
+ #sound-dai-cells = <1>;
+ clock-output-names = "fsgen";
+ status = "disabled";
+ };
+
+ swr1: soundwire@a080000 {
+ compatible = "qcom,soundwire-v3.1.0";
+ reg = <0x0 0x0a080000 0x0 0x10000>;
+ qcom,swr-master-ee-val = <0>;
+
+ interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "core", "wakeup";
+
+ clocks = <&vamacro>;
+ clock-names = "iface";
+
+ label = "VA_TX";
+
+ qcom,din-ports = <4>;
+ qcom,dout-ports = <0>;
+
+ resets = <&audiocorecc AUDIO_CORE_CSR_TX_SWR_CGCR>;
+ reset-names = "swr_audio_cgcr";
+
+ qcom,ports-sinterval-low = /bits/ 8 <0x01 0x01 0x03 0x03>;
+ qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x01 0x01>;
+ qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x00 0x00>;
+ qcom,ports-hstart = /bits/ 8 <0xff 0xff 0xff 0xff>;
+ qcom,ports-hstop = /bits/ 8 <0xff 0xff 0xff 0xff>;
+ qcom,ports-word-length = /bits/ 8 <0xff 0xff 0xff 0xff>;
+ qcom,ports-block-pack-mode = /bits/ 8 <0xff 0xff 0xff 0xff>;
+ qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff>;
+ qcom,ports-lane-control = /bits/ 8 <0x01 0x02 0x00 0x00>;
+
+ #sound-dai-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
sram@c11e000 {
compatible = "qcom,shikra-imem", "mmio-sram";
reg = <0x0 0x0c11e000 0x0 0x1000>;
--
2.34.1
^ permalink raw reply related
* [PATCH v1 5/8] arm64: dts: qcom: shikra-cqm-evk: Enable sound card support
From: Mohammad Rafi Shaik @ 2026-06-16 20:13 UTC (permalink / raw)
To: Srinivas Kandagatla, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-sound, linux-arm-msm, devicetree, linux-kernel
In-Reply-To: <20260616201315.2565115-1-mohammad.rafi.shaik@oss.qualcomm.com>
Enable the sound card on the shikra-cqm-evk platform, including
the PM4125 (Rouleur) headset codec, WSA885x external speaker path,
and QAIF backend links.
Also enable the required LPASS macro and SoundWire nodes, along with
the necessary pinctrl configurations for DMIC and I2S interfaces.
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/shikra-cqm-evk.dts | 222 +++++++++++++++++++
arch/arm64/boot/dts/qcom/shikra-cqm-som.dtsi | 5 +
2 files changed, 227 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/shikra-cqm-evk.dts b/arch/arm64/boot/dts/qcom/shikra-cqm-evk.dts
index b88652703fb8..b68d196b9d04 100644
--- a/arch/arm64/boot/dts/qcom/shikra-cqm-evk.dts
+++ b/arch/arm64/boot/dts/qcom/shikra-cqm-evk.dts
@@ -5,6 +5,7 @@
/dts-v1/;
+#include <dt-bindings/sound/qcom,qaif.h>
#include "shikra-cqm-som.dtsi"
#include "shikra-evk.dtsi"
@@ -23,6 +24,74 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ sound: sound {
+ compatible = "qcom,shikra-cqm-sndcard";
+ model = "shikra-cqm-evk";
+
+ audio-routing = "IN1_HPHL", "HPHL_OUT",
+ "IN2_HPHR", "HPHR_OUT",
+ "AMIC2", "MIC BIAS2",
+ "VA DMIC0", "vdd-micb",
+ "VA DMIC1", "vdd-micb",
+ "VA DMIC2", "vdd-micb",
+ "VA DMIC3", "vdd-micb";
+
+ pinctrl-0 = <&i2s2_default>, <&dmic_eldo_en_default>;
+ pinctrl-names = "default";
+
+ headset-capture-dai-link {
+ link-name = "Headphones Capture";
+
+ codec {
+ sound-dai = <&pmic4125_codec 1>,
+ <&swr1 0>,
+ <&vamacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&qaif_cpu QAIF_CDC_DMA_VA_TX0>;
+ };
+ };
+
+ headset-playback-dai-link {
+ link-name = "Headphones Playback";
+
+ codec {
+ sound-dai = <&pmic4125_codec 0>,
+ <&swr0 0>,
+ <&rxmacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&qaif_cpu QAIF_CDC_DMA_RX0>;
+ };
+ };
+
+ wsa-speaker-dai-link {
+ link-name = "WSA Speaker Playback";
+
+ codec {
+ sound-dai = <&wsa885x_i2c>;
+ };
+
+ cpu {
+ sound-dai = <&qaif_cpu QAIF_MI2S_TDM_AIF2>;
+ };
+ };
+
+ va-dmic-dai-link {
+ link-name = "VA DMIC Capture";
+
+ codec {
+ sound-dai = <&vamacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&qaif_cpu QAIF_CDC_DMA_VA_TX0>;
+ };
+ };
+ };
+
wcn3988-pmu {
compatible = "qcom,wcn3988-pmu";
@@ -60,6 +129,79 @@ vreg_pmu_ch1: ldo4 {
};
};
+&gpr {
+ status = "disabled";
+};
+
+&i2c3 {
+ status = "okay";
+
+ wsa885x_i2c: speaker@c {
+ compatible = "qcom,wsa885x-i2c";
+ reg = <0x0c>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wsa885x_i2c_spkr_sd_n>;
+
+ interrupt-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>;
+ powerdown-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ vdd-1p8-supply = <&pm4125_l15>;
+ vdd-io-supply = <&pm4125_l15>;
+ qcom,battery-config = <2>;
+
+ qcom,wsa885x-init-table =
+ <0x8470 0x2
+ 0x8470 0x0
+ 0x8470 0x1
+ 0x0004 0x1
+ 0x8602 0x60
+ 0x8622 0x60
+ 0x8458 0x79
+ 0x810B 0xD9
+ 0x8111 0xD9
+ 0x813C 0x08
+ 0x8102 0x04
+ 0x811C 0x29
+ 0x811D 0x40
+ 0x8129 0x40
+ 0x811A 0x80
+ 0x8126 0x80
+ 0x8103 0x6
+ 0x80CA 0x85
+ 0x80CB 0xE
+ 0x80CC 0xC
+ 0x80D0 0x80
+ 0x80BA 0xC0
+ 0x841C 0x4E
+ 0x8435 0x47
+ 0x86CE 0x09
+ 0x8667 0x34
+ 0x800D 0x08>;
+ #sound-dai-cells = <0>;
+ };
+};
+
+&qaif_cpu {
+ status = "okay";
+ qaif_aif_if2: aif-interface@2 {
+ compatible = "qcom,qaif-tdm-dai";
+ reg = <QAIF_MI2S_TDM_AIF2>;
+ qcom,qaif-aif-sync-mode = <QAIF_AIF_SYNC_MODE_LONG>;
+ qcom,qaif-aif-sync-src = <QAIF_AIF_SYNC_SRC_MASTER>;
+ qcom,qaif-aif-sync-delay = <1>;
+ qcom,qaif-aif-slot-width-rx = <32>;
+ qcom,qaif-aif-slot-width-tx = <32>;
+ qcom,qaif-aif-slot-en-rx-mask = <0x3>;
+ qcom,qaif-aif-slot-en-tx-mask = <0x3>;
+ qcom,qaif-aif-ctrl-data-oe;
+ /* Lane 0: RX (mic); Lane 1: TX (speaker) */
+ qcom,qaif-aif-lane-config = <QAIF_AIF_LANE_ENABLE QAIF_AIF_LANE_DIR_RX>,
+ <QAIF_AIF_LANE_ENABLE QAIF_AIF_LANE_DIR_TX>;
+ /* frame length = slot-width (32) * bits-per-lane (2) = 64 bits */
+ qcom,qaif-aif-bits-per-lane = <2>;
+ };
+};
+
&remoteproc_cdsp {
firmware-name = "qcom/shikra/cdsp.mbn";
@@ -79,6 +221,10 @@ &remoteproc_mpss {
status = "okay";
};
+&rxmacro {
+ status = "okay";
+};
+
&audiocorecc {
status = "okay";
};
@@ -99,6 +245,74 @@ &sdhc_1 {
status = "okay";
};
+&spmi_bus {
+ pmic@0 {
+ pmic4125_codec: audio-codec@f000 {
+ compatible = "qcom,pm4125-codec";
+ reg = <0xf000>;
+ vdd-io-supply = <&pm4125_l15>;
+ vdd-cp-supply = <&pm4125_s1>;
+ vdd-pa-vpos-supply = <&pm4125_s1>;
+
+ vdd-mic-bias-supply = <&pm4125_l22>;
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+
+ qcom,rx-device = <&pm4125_rx>;
+ qcom,tx-device = <&pm4125_tx>;
+ #sound-dai-cells = <1>;
+
+ status = "okay";
+ };
+ };
+};
+
+&swr0 {
+ status = "okay";
+
+ pm4125_rx: codec@0,4 {
+ compatible = "sdw20217010c00";
+ reg = <0 4>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr1 {
+ status = "okay";
+
+ pm4125_tx: codec@0,3 {
+ compatible = "sdw20217010c00";
+ reg = <0 3>;
+ qcom,tx-port-mapping = <2 2 3 4>;
+ };
+};
+
+&tlmm {
+ dmic_eldo_en_default: dmic-eldo-default-active-state {
+ pins = "gpio71";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ output-high;
+ };
+
+ i2s2_default: i2s2-default-active-state {
+ pins = "gpio100", "gpio101", "gpio102", "gpio103";
+ function = "i2s2";
+ drive-strength = <8>;
+ output-high;
+ bias-disable;
+ };
+
+ wsa885x_i2c_spkr_sd_n: wsa885x-i2c-spkr-sd-n-active-state {
+ pins = "gpio2";
+ function = "gpio";
+ input-disable;
+ output-enable;
+ };
+};
+
&uart8 {
status = "okay";
@@ -110,6 +324,14 @@ bluetooth {
};
};
+&vamacro {
+ pinctrl-0 = <&dmic01_default>, <&dmic23_default>, <&tx_swr_active>;
+ pinctrl-names = "default";
+
+ qcom,dmic-sample-rate = <4800000>;
+ status = "okay";
+};
+
&wifi {
vdd-0.8-cx-mx-supply = <&pm4125_l7>;
vdd-1.8-xo-supply = <&vreg_pmu_xo>;
diff --git a/arch/arm64/boot/dts/qcom/shikra-cqm-som.dtsi b/arch/arm64/boot/dts/qcom/shikra-cqm-som.dtsi
index dc3861489f64..86b323f2fa58 100644
--- a/arch/arm64/boot/dts/qcom/shikra-cqm-som.dtsi
+++ b/arch/arm64/boot/dts/qcom/shikra-cqm-som.dtsi
@@ -53,6 +53,11 @@ &rpm_requests {
regulators {
compatible = "qcom,rpm-pm2250-regulators";
+ pm4125_s1: s1 {
+ regulator-min-microvolt = <1396000>;
+ regulator-max-microvolt = <1396000>;
+ };
+
pm4125_s2: s2 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1200000>;
--
2.34.1
^ permalink raw reply related
* [PATCH v1 6/8] arm64: dts: qcom: shikra-cqs-evk: Enable sound card support
From: Mohammad Rafi Shaik @ 2026-06-16 20:13 UTC (permalink / raw)
To: Srinivas Kandagatla, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-sound, linux-arm-msm, devicetree, linux-kernel,
Pratyush Meduri
In-Reply-To: <20260616201315.2565115-1-mohammad.rafi.shaik@oss.qualcomm.com>
Enable the sound card on the shikra-cqs-evk platform, including
WSA885x external speaker path and DMIC via VA macro
Also enable the required LPASS macro along with the necessary
pinctrl configurations for DMIC and I2S interfaces.
Co-developed-by: Pratyush Meduri <mpratyus@qti.qualcomm.com>
Signed-off-by: Pratyush Meduri <mpratyus@qti.qualcomm.com>
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/shikra-cqs-evk.dts | 149 ++++++++++++++++++++
1 file changed, 149 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/shikra-cqs-evk.dts b/arch/arm64/boot/dts/qcom/shikra-cqs-evk.dts
index 6498ef47bf3a..76d41b645741 100644
--- a/arch/arm64/boot/dts/qcom/shikra-cqs-evk.dts
+++ b/arch/arm64/boot/dts/qcom/shikra-cqs-evk.dts
@@ -23,6 +23,57 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ sound {
+ compatible = "qcom,shikra-cqs-sndcard";
+ model = "shikra-cqs-evk";
+
+ pinctrl-0 = <&i2s2_default>, <&dmic_eldo_en_default>;
+ pinctrl-names = "default";
+
+ audio-routing = "VA DMIC0", "vdd-micb",
+ "VA DMIC1", "vdd-micb",
+ "VA DMIC2", "vdd-micb",
+ "VA DMIC3", "vdd-micb";
+
+ va-dmic-dai-link {
+ link-name = "VA DMIC Capture";
+
+ codec {
+ sound-dai = <&vamacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wsa-playback-dai-link {
+ link-name = "WSA Playback";
+
+ codec {
+ sound-dai = <&wsa885x_i2c>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <32>;
+ dai-tdm-slot-rx-mask = <1 1>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai SECONDARY_TDM_RX_0>;
+ dai-tdm-slot-num = <2>;
+ dai-tdm-slot-width = <32>;
+ dai-tdm-slot-rx-mask = <1 1>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
+
wcn3988-pmu {
compatible = "qcom,wcn3988-pmu";
@@ -60,6 +111,66 @@ vreg_pmu_ch1: ldo4 {
};
};
+&i2c3 {
+ status = "okay";
+
+ wsa885x_i2c: speaker@c {
+ compatible = "qcom,wsa885x-i2c";
+ reg = <0x0c>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wsa885x_i2c_spkr_sd_n>;
+
+ interrupt-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>;
+ powerdown-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ vdd-1p8-supply = <&pm4125_l15>;
+ vdd-io-supply = <&pm4125_l15>;
+ qcom,battery-config = <2>;
+
+ qcom,wsa885x-init-table =
+ <0x8470 0x2
+ 0x8470 0x0
+ 0x8470 0x1
+ 0x0004 0x1
+ 0x8602 0x60
+ 0x8622 0x60
+ 0x8458 0x79
+ 0x810B 0xD9
+ 0x8111 0xD9
+ 0x813C 0x08
+ 0x8102 0x04
+ 0x811C 0x29
+ 0x811D 0x40
+ 0x8129 0x40
+ 0x811A 0x80
+ 0x8126 0x80
+ 0x8103 0x6
+ 0x80CA 0x85
+ 0x80CB 0xE
+ 0x80CC 0xC
+ 0x80D0 0x80
+ 0x80BA 0xC0
+ 0x841C 0x4E
+ 0x8435 0x47
+ 0x86CE 0x09
+ 0x8667 0x34
+ 0x800D 0x08>;
+
+ #sound-dai-cells = <0>;
+ };
+};
+
+&q6apmbedai {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dai@40 {
+ reg = <SECONDARY_TDM_RX_0>;
+ clocks = <&q6prmcc LPASS_CLK_ID_AUD_INTF2_IBIT
+ LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ clock-names = "bclk";
+ };
+};
+
&remoteproc_cdsp {
firmware-name = "qcom/shikra/cdsp.mbn";
@@ -100,6 +211,31 @@ &sdhc_1 {
status = "okay";
};
+&tlmm {
+ dmic_eldo_en_default: dmic-eldo-default-active-state {
+ pins = "gpio71";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ output-high;
+ };
+
+ i2s2_default: i2s2-default-active-state {
+ pins = "gpio100", "gpio101", "gpio102", "gpio103";
+ function = "i2s2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ wsa885x_i2c_spkr_sd_n: wsa885x-i2c-spkr-sd-n-active-state {
+ pins = "gpio2";
+ function = "gpio";
+ drive-strength = <8>;
+ input-disable;
+ output-enable;
+ };
+};
+
&uart8 {
status = "okay";
@@ -111,6 +247,19 @@ bluetooth {
};
};
+&vamacro {
+ pinctrl-0 = <&dmic01_default>, <&dmic23_default>, <&tx_swr_active>;
+ pinctrl-names = "default";
+
+ clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ clock-names = "mclk",
+ "npl";
+
+ qcom,dmic-sample-rate = <4800000>;
+ status = "okay";
+};
+
&wifi {
vdd-0.8-cx-mx-supply = <&pm4125_l7>;
vdd-1.8-xo-supply = <&vreg_pmu_xo>;
--
2.34.1
^ permalink raw reply related
* [PATCH v1 7/8] arm64: dts: qcom: shikra-iqs-evk: Enable sound card support
From: Mohammad Rafi Shaik @ 2026-06-16 20:13 UTC (permalink / raw)
To: Srinivas Kandagatla, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-sound, linux-arm-msm, devicetree, linux-kernel,
Ajay Kumar Nandam
In-Reply-To: <20260616201315.2565115-1-mohammad.rafi.shaik@oss.qualcomm.com>
Enable the IQS EVK audio card using MAX98091 on I2S0 for primary
playback/capture and VA DMIC capture through q6apm backend links.
Add board clock and pinctrl states required for codec IRQ, external
mclk and digital mic routing.
Co-developed-by: Ajay Kumar Nandam <ajay.nandam@oss.qualcomm.com>
Signed-off-by: Ajay Kumar Nandam <ajay.nandam@oss.qualcomm.com>
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/shikra-iqs-evk.dts | 143 ++++++++++++++++++++
1 file changed, 143 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/shikra-iqs-evk.dts b/arch/arm64/boot/dts/qcom/shikra-iqs-evk.dts
index fd691d53a0fa..62f405578172 100644
--- a/arch/arm64/boot/dts/qcom/shikra-iqs-evk.dts
+++ b/arch/arm64/boot/dts/qcom/shikra-iqs-evk.dts
@@ -23,6 +23,75 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ sound {
+ compatible = "qcom,shikra-iqs-sndcard";
+ model = "shikra-iqs-evk";
+
+ pinctrl-0 = <&i2s0_default>, <&ext_mclk2_active>;
+ pinctrl-names = "default";
+
+ audio-routing = "IN34", "Headset Mic",
+ "Headset Mic", "MICBIAS",
+ "DMICL", "Int Mic",
+ "Int Mic", "MICBIAS",
+ "Headphone", "HPL",
+ "Headphone", "HPR",
+ "Speaker", "SPKL",
+ "Speaker", "SPKR",
+ "VA DMIC0", "vdd-micb",
+ "VA DMIC1", "vdd-micb",
+ "VA DMIC2", "vdd-micb",
+ "VA DMIC3", "vdd-micb";
+
+ pri-i2s-playback-dai-link {
+ link-name = "Analog Playback";
+
+ codec {
+ sound-dai = <&max98091>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai PRIMARY_MI2S_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ pri-i2s-capture-dai-link {
+ link-name = "Analog Capture";
+
+ codec {
+ sound-dai = <&max98091>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai PRIMARY_MI2S_TX>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ va-dmic-dai-link {
+ link-name = "VA DMIC Capture";
+
+ codec {
+ sound-dai = <&vamacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
+
vreg_wcn_3p3: regulator-wcn-3p3 {
compatible = "regulator-fixed";
regulator-name = "wcn_3p3";
@@ -68,6 +137,36 @@ vreg_pmu_ch1: ldo4 {
};
};
+&i2c3 {
+ status = "okay";
+
+ max98091: audio-codec@10 {
+ compatible = "maxim,max98091";
+ reg = <0x10>;
+
+ pinctrl-0 = <&max98091_default>;
+ pinctrl-names = "default";
+
+ interrupts-extended = <&tlmm 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&q6prmcc LPASS_CLK_ID_MCLK_2 LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ clock-names = "mclk";
+ assigned-clocks = <&q6prmcc LPASS_CLK_ID_MCLK_2 LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ assigned-clock-rates = <12288000>;
+ #sound-dai-cells = <0>;
+ };
+};
+
+&q6apmbedai {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dai@16 {
+ reg = <PRIMARY_MI2S_RX>;
+ clocks = <&q6prmcc LPASS_CLK_ID_AUD_INTF0_IBIT LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ clock-names = "bclk";
+ };
+};
+
&remoteproc_cdsp {
firmware-name = "qcom/shikra/cdsp.mbn";
@@ -103,6 +202,36 @@ &sdhc_1 {
status = "okay";
};
+&tlmm {
+ dmic_eldo_en_default: dmic-eldo-default-active-state {
+ pins = "gpio71";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ output-high;
+ };
+
+ ext_mclk2_active: ext-mclk2-state {
+ pins = "gpio110";
+ function = "ext_mclk";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ i2s0_default: i2s0-default-active-state {
+ pins = "gpio105", "gpio106", "gpio107", "gpio108", "gpio109";
+ function = "i2s0";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ max98091_default: max98091-default-state {
+ pins = "gpio28";
+ function = "gpio";
+ bias-pull-up;
+ };
+};
+
&uart8 {
status = "okay";
@@ -114,6 +243,20 @@ bluetooth {
};
};
+&vamacro {
+ clocks = <&q6prmcc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+ <&q6prmcc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
+ clock-names = "mclk",
+ "npl";
+
+ pinctrl-0 = <&dmic01_default>, <&dmic23_default>, <&dmic_eldo_en_default>;
+ pinctrl-names = "default";
+
+ qcom,dmic-sample-rate = <4800000>;
+
+ status = "okay";
+};
+
&wifi {
vdd-0.8-cx-mx-supply = <&pm8150_s4>;
vdd-1.8-xo-supply = <&vreg_pmu_xo>;
--
2.34.1
^ permalink raw reply related
* [PATCH v1 8/8] arm64: defconfig: Enable Qualcomm QAIF and WSA885X-I2C drivers
From: Mohammad Rafi Shaik @ 2026-06-16 20:13 UTC (permalink / raw)
To: Srinivas Kandagatla, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-sound, linux-arm-msm, devicetree, linux-kernel
In-Reply-To: <20260616201315.2565115-1-mohammad.rafi.shaik@oss.qualcomm.com>
Enable the QAIF CPU DAI and WSA885X I2C codec as modules in
arm64 defconfig.
These options are required to exercise the Shikra EVK
audio paths enabled by the preceding DTS changes.
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
---
arch/arm64/configs/defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 271589322efd..067f4ecc05bf 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -1099,6 +1099,7 @@ CONFIG_SND_SOC_QCOM=m
CONFIG_SND_SOC_APQ8016_SBC=m
CONFIG_SND_SOC_QDSP6_USB=m
CONFIG_SND_SOC_MSM8996=m
+CONFIG_SND_SOC_QCOM_QAIF=m
CONFIG_SND_SOC_SDM845=m
CONFIG_SND_SOC_SM8250=m
CONFIG_SND_SOC_SC8280XP=m
@@ -1175,6 +1176,7 @@ CONFIG_SND_SOC_WM8978=m
CONFIG_SND_SOC_WSA881X=m
CONFIG_SND_SOC_WSA883X=m
CONFIG_SND_SOC_WSA884X=m
+CONFIG_SND_SOC_WSA885X_I2C=m
CONFIG_SND_SOC_NAU8822=m
CONFIG_SND_SOC_LPASS_WSA_MACRO=m
CONFIG_SND_SOC_LPASS_VA_MACRO=m
--
2.34.1
^ permalink raw reply related
* Re: [PATCH] dt-bindings: sound: add toshiba,apb-dummy-codec binding
From: Mark Brown @ 2026-06-16 20:23 UTC (permalink / raw)
To: Pablo D. Bergamasco
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Vaibhav Agarwal,
Mark Greer, Liam Girdwood, linux-sound, devicetree, linux-kernel
In-Reply-To: <20260616185619.1581174-1-danpablo@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 525 bytes --]
On Tue, Jun 16, 2026 at 03:56:19PM -0300, Pablo D. Bergamasco wrote:
> Add device tree binding documentation for the Toshiba APBridge
> dummy ALSA SoC codec used in the Greybus audio framework.
Please submit patches using subject lines reflecting the style for the
subsystem, this makes it easier for people to identify relevant patches.
Look at what existing commits in the area you're changing are doing and
make sure your subject lines visually resemble what they're doing.
There's no need to resubmit to fix this alone.
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply
* [PATCH RFC v4 00/12] ZTE zx297520v3 clock bindings and driver
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
Hi,
I am sending version 4 of my zx297520v3 clock patch. The major change is
using regmaps rather than raw mmio to access the clocks and moving reset
handling into its own aux bus driver.
I think the list of clocks in my driver is fairly complete; It is
certainly a lot better than what the downstream ZTE drivers have. I
deduced a lot of it by trial and error. I am sure there are some clocks
missing that will need to be added to the binding later. Afaiu adding
clocks is not an issue, but removing or reordering them is an ABI break.
I expect Sashiko to find a lot of slopiness mistakes, so I kept the
[RFC] tag for this submission.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
Changes in v4:
*) Use syscon and regmap instead of raw IO
*) Move reset to its own driver on the aux bus, but keep reset and clk
in the same binding as it matches the way the hardware works
*) Go back to having matrixclk in its own device because syscon deals
poorly with multi io reg devices. List all PLL outputs from topclk as
inputs to matrixclk
*) Some more hardware research: Figure out the parents of the 4 possible
GPIO clock outputs and declare them in the driver. They are unused on
the hardware I have, but they show that all PLLs can be used.
- Link to v3: https://lore.kernel.org/r/20260529-zx29clk-v3-0-c7fe54ea388f@gmail.com
Changes in v3:
Model top and matrix clocks as one device
Add PLL driver
Fixed a few issues found by Sashiko: register lock, some missing devm_,
error handling
v2: Fix build issues introduced by checkpatch.pl fixes that I didn't
spot earlier.
---
Stefan Dösinger (12):
dt-bindings: clk: zte: Add zx297520v3 top clock and reset bindings
dt-bindings: clk: zte: Add zx297520v3 matrix clock and reset bindings
dt-bindings: clk: zte: Add zx297520v3 LSP clock and reset bindings
clk: zte: Add Clock registration infrastructure.
clk: zte: Add zx PLL support infrastructure
clk: zte: Add regmap based clocks
clk: zte: Introduce a driver for zx297520v3 top clocks
clk: zte: Introduce a driver for zx297520v3 matrix clocks
clk: zte: Introduce a driver for zx297520v3 LSP clocks
reset: zte: Add a zx297520v3 reset driver
ARM: dts: zte: Declare zx297520v3 clock device nodes
ARM: dts: zte: Add a syscon-reboot for zx297520v3 boards
.../bindings/clock/zte,zx297520v3-lspclk.yaml | 130 ++++
.../bindings/clock/zte,zx297520v3-matrixclk.yaml | 180 +++++
.../bindings/clock/zte,zx297520v3-topclk.yaml | 70 ++
MAINTAINERS | 4 +
arch/arm/boot/dts/zte/zx297520v3.dtsi | 97 ++-
drivers/clk/Kconfig | 1 +
drivers/clk/Makefile | 1 +
drivers/clk/zte/Kconfig | 28 +
drivers/clk/zte/Makefile | 6 +
drivers/clk/zte/clk-regmap.c | 247 +++++++
drivers/clk/zte/clk-zx.c | 157 ++++
drivers/clk/zte/clk-zx.h | 79 ++
drivers/clk/zte/clk-zx297520v3.c | 795 +++++++++++++++++++++
drivers/clk/zte/pll-zx.c | 477 +++++++++++++
drivers/reset/Kconfig | 11 +
drivers/reset/Makefile | 1 +
drivers/reset/reset-zte-zx297520v3.c | 224 ++++++
include/dt-bindings/clock/zte,zx297520v3-clk.h | 219 ++++++
18 files changed, 2718 insertions(+), 9 deletions(-)
---
base-commit: c1ecb239fa3456529a32255359fc78b69eb9d847
change-id: 20260510-zx29clk-2e4d39e3128c
Best regards,
--
Stefan Dösinger <stefandoesinger@gmail.com>
^ permalink raw reply
* [PATCH RFC v4 01/12] dt-bindings: clk: zte: Add zx297520v3 top clock and reset bindings
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
These SoCs have 3 clock and reset controllers: Top, Matrix and LSP. The
separation of concerns between Top and Matrix and the interface between
them is poorly defined in the hardware, so the bindings list all
potential PLL clocks that might be passed between them.
Generally every device has two clocks (one work clock, and one that
connects it to the bus, I call it PCLK), two reset bits (I don't know
what the difference is - sometimes asserting one is enough to reset the
device, sometimes both need to be asserted). PCLK and WCLK are
controlled by individual gates. Some devices have a mux and/or a
divider for their work clock. Some devices, like the GPIO controller,
only have reset bits and no clocks.
The top clock controller is fed by a 26mhz external oscillator and has 4
PLLs to generate other clock rates. ZTE's kernel mostly relies on the
boot ROM to set up PLLs, but one LTE-Related PLL is not configured
on some boards. Therefore my driver contains code to program PLLs. It
produces identical settings as the boot ROM for the pre-programmed
frequencies.
Not all clocks will have an explicit user in the end. I am defining a
lot of them simply to shut them off. The boot loader sets up a few of
the proprietary timers, which will send regular IRQs (although the
kernel of course doesn't need to listen to them). I don't plan to add a
driver for the proprietary timer as I see no use for them - the ARM arch
timer works just fine. I will add a driver for the very similar
proprietary watchdog though.
The clock list in this patch is pretty complete but not exhaustive.
There are other bits that are enabled, but I couldn't deduce what they
are controlling by trial and error. Some of them seem to do nothing.
Others cause an instant hang of the board when disabled. It is quite
likely that a handful more clocks will be added in the future, but not a
large number.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
.../bindings/clock/zte,zx297520v3-topclk.yaml | 70 ++++++++++++
MAINTAINERS | 2 +
include/dt-bindings/clock/zte,zx297520v3-clk.h | 118 +++++++++++++++++++++
3 files changed, 190 insertions(+)
diff --git a/Documentation/devicetree/bindings/clock/zte,zx297520v3-topclk.yaml b/Documentation/devicetree/bindings/clock/zte,zx297520v3-topclk.yaml
new file mode 100644
index 000000000000..374f63891288
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/zte,zx297520v3-topclk.yaml
@@ -0,0 +1,70 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/zte,zx297520v3-topclk.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ZTE zx297520v3 SoC top clock and reset controller
+
+maintainers:
+ - Stefan Dösinger <stefandoesinger@gmail.com>
+
+description: |
+ The zx297520v3's top clock controller generates clocks for core devices on the
+ board like the main bus, USB and timers. In addition to clocks it has reset
+ controls for peripherals, a global board reset and watchdog reset controls.
+
+ The controller has two clock inputs: a 26 MHz and a 32 KHz external
+ oscillator. They need to be provided as input clocks. The controller provides
+ clocks to the downstream Matrix clock controller.
+
+ All available clocks are defined as preprocessor macros in the
+ 'dt-bindings/clock/zte,zx297520v3-clk.h' header.
+
+properties:
+ compatible:
+ items:
+ - const: zte,zx297520v3-topclk
+ - const: syscon
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: 26 MHz external oscillator
+ - description: 32 KHz external oscillator
+
+ clock-names:
+ items:
+ - const: osc26m
+ - const: osc32k
+
+ "#clock-cells":
+ const: 1
+
+ "#reset-cells":
+ const: 1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - '#clock-cells'
+ - '#reset-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/zte,zx297520v3-clk.h>
+
+ clock-controller@13b000 {
+ compatible = "zte,zx297520v3-topclk", "syscon";
+ reg = <0x0013b000 0x400>;
+ clocks = <&osc26m>, <&osc32k>;
+ clock-names = "osc26m", "osc32k";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 8629ed2aa82f..0cc1ede3c80c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3867,8 +3867,10 @@ L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Odd fixes
F: Documentation/arch/arm/zte/
F: Documentation/devicetree/bindings/arm/zte.yaml
+F: Documentation/devicetree/zte,zx297520v3-*
F: arch/arm/boot/dts/zte/
F: arch/arm/mach-zte/
+F: include/dt-bindings/clock/zte,zx297520v3-clk.h
ARM/ZYNQ ARCHITECTURE
M: Michal Simek <michal.simek@amd.com>
diff --git a/include/dt-bindings/clock/zte,zx297520v3-clk.h b/include/dt-bindings/clock/zte,zx297520v3-clk.h
new file mode 100644
index 000000000000..cf436ff20dfe
--- /dev/null
+++ b/include/dt-bindings/clock/zte,zx297520v3-clk.h
@@ -0,0 +1,118 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (C) Stefan Dösinger.
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_ZX297520V3_H
+#define __DT_BINDINGS_CLOCK_ZX297520V3_H
+
+#define ZX297520V3_M0_WCLK 1
+#define ZX297520V3_SRAM1_PCLK 2
+#define ZX297520V3_SRAM2_PCLK 3
+#define ZX297520V3_UART0_WCLK 4
+#define ZX297520V3_UART0_PCLK 5
+#define ZX297520V3_I2C0_WCLK 6
+#define ZX297520V3_I2C0_PCLK 7
+#define ZX297520V3_RTC_WCLK 8
+#define ZX297520V3_RTC_PCLK 9
+#define ZX297520V3_LPM_GSM_WCLK 10
+#define ZX297520V3_LPM_GSM_PCLK 11
+#define ZX297520V3_LPM_LTE_WCLK 12
+#define ZX297520V3_LPM_LTE_PCLK 13
+#define ZX297520V3_LPM_TD_WCLK 14
+#define ZX297520V3_LPM_TD_PCLK 15
+#define ZX297520V3_LPM_W_WCLK 16
+#define ZX297520V3_LPM_W_PCLK 17
+#define ZX297520V3_TIMER_T08_WCLK 18
+#define ZX297520V3_TIMER_T08_PCLK 19
+#define ZX297520V3_TIMER_T09_WCLK 20
+#define ZX297520V3_TIMER_T09_PCLK 21
+#define ZX297520V3_MPLL 22
+#define ZX297520V3_MPLL_D2 23
+#define ZX297520V3_MPLL_D3 24
+#define ZX297520V3_MPLL_D4 25
+#define ZX297520V3_MPLL_D5 26
+#define ZX297520V3_MPLL_D6 27
+#define ZX297520V3_MPLL_D8 28
+#define ZX297520V3_MPLL_D12 29
+#define ZX297520V3_MPLL_D16 30
+#define ZX297520V3_MPLL_D26 31
+#define ZX297520V3_UPLL 32
+#define ZX297520V3_UPLL_D2 33
+#define ZX297520V3_UPLL_D3 34
+#define ZX297520V3_UPLL_D4 35
+#define ZX297520V3_UPLL_D5 36
+#define ZX297520V3_UPLL_D6 37
+#define ZX297520V3_UPLL_D8 38
+#define ZX297520V3_UPLL_D12 39
+#define ZX297520V3_UPLL_D16 40
+#define ZX297520V3_DPLL 41
+#define ZX297520V3_DPLL_D2 42
+#define ZX297520V3_DPLL_D3 43
+#define ZX297520V3_DPLL_D4 44
+#define ZX297520V3_DPLL_D5 45
+#define ZX297520V3_DPLL_D6 46
+#define ZX297520V3_DPLL_D8 47
+#define ZX297520V3_DPLL_D12 48
+#define ZX297520V3_DPLL_D16 49
+#define ZX297520V3_GPLL 50
+#define ZX297520V3_GPLL_D2 51
+#define ZX297520V3_GPLL_D3 52
+#define ZX297520V3_GPLL_D4 53
+#define ZX297520V3_GPLL_D5 54
+#define ZX297520V3_GPLL_D6 55
+#define ZX297520V3_GPLL_D8 56
+#define ZX297520V3_GPLL_D12 57
+#define ZX297520V3_GPLL_D16 58
+#define ZX297520V3_PMM_WCLK 59
+#define ZX297520V3_PMM_PCLK 60
+#define ZX297520V3_OUT0_WCLK 61
+#define ZX297520V3_OUT1_WCLK 62
+#define ZX297520V3_OUT2_WCLK 63
+#define ZX297520V3_OUT32K_WCLK 64
+#define ZX297520V3_RMIIPHY_WCLK 65
+#define ZX297520V3_TIMER_T12_WCLK 66
+#define ZX297520V3_TIMER_T12_PCLK 67
+#define ZX297520V3_TIMER_T13_WCLK 68
+#define ZX297520V3_TIMER_T13_PCLK 69
+#define ZX297520V3_TIMER_T14_WCLK 70
+#define ZX297520V3_TIMER_T14_PCLK 71
+#define ZX297520V3_TIMER_T15_WCLK 72
+#define ZX297520V3_TIMER_T15_PCLK 73
+#define ZX297520V3_TIMER_T16_WCLK 74
+#define ZX297520V3_TIMER_T16_PCLK 75
+#define ZX297520V3_TIMER_T17_WCLK 76
+#define ZX297520V3_TIMER_T17_PCLK 77
+#define ZX297520V3_WDT_T18_WCLK 78
+#define ZX297520V3_WDT_T18_PCLK 79
+#define ZX297520V3_USIM1_WCLK 80
+#define ZX297520V3_USIM1_PCLK 81
+#define ZX297520V3_AHB_WCLK 82
+#define ZX297520V3_AHB_PCLK 83
+#define ZX297520V3_USB_WCLK 84
+#define ZX297520V3_USB_PCLK 85
+#define ZX297520V3_HSIC_WCLK 86
+#define ZX297520V3_HSIC_PCLK 87
+
+#define ZX297520V3_ZSP_RESET 0
+#define ZX297520V3_UART0_RESET 1
+#define ZX297520V3_I2C0_RESET 2
+#define ZX297520V3_RTC_RESET 3
+#define ZX297520V3_TIMER_T08_RESET 4
+#define ZX297520V3_TIMER_T09_RESET 5
+#define ZX297520V3_PMM_RESET 6
+#define ZX297520V3_GPIO_RESET 7
+#define ZX297520V3_GPIO8_RESET 8
+#define ZX297520V3_TIMER_T12_RESET 9
+#define ZX297520V3_TIMER_T13_RESET 10
+#define ZX297520V3_TIMER_T14_RESET 11
+#define ZX297520V3_TIMER_T15_RESET 12
+#define ZX297520V3_TIMER_T16_RESET 13
+#define ZX297520V3_TIMER_T17_RESET 14
+#define ZX297520V3_WDT_T18_RESET 15
+#define ZX297520V3_USIM1_RESET 16
+#define ZX297520V3_AHB_RESET 17
+#define ZX297520V3_USB_RESET 18
+#define ZX297520V3_HSIC_RESET 19
+
+#endif /* __DT_BINDINGS_CLOCK_ZX297520V3_H */
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 02/12] dt-bindings: clk: zte: Add zx297520v3 matrix clock and reset bindings
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
I split matrixclk into its own controller again because syscon/regmap
deals poorly with device nodes that have more than one memory region. As
a consequence I am passing all PLL outputs generated on Topclk down to
Matrixclk.
The syscon is used to generate the regmap shared between the clock and
auxiliary reset drivers. The register space also contains at least one
extra block of functionality, hardware spinlocks, that I expect will be
necessary to communicate correctly with the LTE DSP firmware blob.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
.../bindings/clock/zte,zx297520v3-matrixclk.yaml | 180 +++++++++++++++++++++
include/dt-bindings/clock/zte,zx297520v3-clk.h | 45 ++++++
2 files changed, 225 insertions(+)
diff --git a/Documentation/devicetree/bindings/clock/zte,zx297520v3-matrixclk.yaml b/Documentation/devicetree/bindings/clock/zte,zx297520v3-matrixclk.yaml
new file mode 100644
index 000000000000..4363ed9be76f
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/zte,zx297520v3-matrixclk.yaml
@@ -0,0 +1,180 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/zte,zx297520v3-matrixclk.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ZTE zx297520v3 SoC matrix clock and reset controller
+
+maintainers:
+ - Stefan Dösinger <stefandoesinger@gmail.com>
+
+description: |
+ This controller controls high speed devices on the zx297520v3 board: The CPU,
+ RAM, SDIO and Ethernet clocks and resets are found here. This controller
+ requires PLL-generated clocks from Topclk as well as the fixed 26 MHz and 32
+ KHz oscillators found on this board.
+
+ Other helper controls are found on this hardware too: It contains a mailbox
+ interface to read RAM properties and hardware spinlock registers.
+
+ All available clocks are defined as preprocessor macros in the
+ 'dt-bindings/clock/zte,zx297520v3-clk.h' header.
+
+properties:
+ compatible:
+ items:
+ - const: zte,zx297520v3-matrixclk
+ - const: syscon
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: 26 MHz external oscillator
+ - description: 32 KHz external oscillator
+ - description: Main PLL output from topclk (usually 624 MHz)
+ - description: Main PLL subdivision factor 2
+ - description: Main PLL subdivision factor 3
+ - description: Main PLL subdivision factor 4
+ - description: Main PLL subdivision factor 5
+ - description: Main PLL subdivision factor 6
+ - description: Main PLL subdivision factor 8
+ - description: Main PLL subdivision factor 12
+ - description: Main PLL subdivision factor 16
+ - description: Main PLL subdivision factor 26
+ - description: Upll output from topclk (Usually 480 MHz)
+ - description: Upll subdivision factor 2
+ - description: Upll subdivision factor 3
+ - description: Upll subdivision factor 4
+ - description: Upll subdivision factor 5
+ - description: Upll subdivision factor 6
+ - description: Upll subdivision factor 8
+ - description: Upll subdivision factor 12
+ - description: Upll subdivision factor 16
+ - description: Dpll output from topclk (usually 492.88 MHz)
+ - description: Dpll subdivision factor 2
+ - description: Dpll subdivision factor 3
+ - description: Dpll subdivision factor 4
+ - description: Dpll subdivision factor 5
+ - description: Dpll subdivision factor 6
+ - description: Dpll subdivision factor 8
+ - description: Dpll subdivision factor 12
+ - description: Dpll subdivision factor 16
+ - description: Gpll output from topclk (usually 200 MHz)
+ - description: Gpll subdivision factor 2
+ - description: Gpll subdivision factor 3
+ - description: Gpll subdivision factor 4
+ - description: Gpll subdivision factor 5
+ - description: Gpll subdivision factor 6
+ - description: Gpll subdivision factor 8
+ - description: Gpll subdivision factor 12
+ - description: Gpll subdivision factor 16
+
+ clock-names:
+ items:
+ - const: osc26m
+ - const: osc32k
+ - const: mpll
+ - const: mpll_d2
+ - const: mpll_d3
+ - const: mpll_d4
+ - const: mpll_d5
+ - const: mpll_d6
+ - const: mpll_d8
+ - const: mpll_d12
+ - const: mpll_d16
+ - const: mpll_d26
+ - const: upll
+ - const: upll_d2
+ - const: upll_d3
+ - const: upll_d4
+ - const: upll_d5
+ - const: upll_d6
+ - const: upll_d8
+ - const: upll_d12
+ - const: upll_d16
+ - const: dpll
+ - const: dpll_d2
+ - const: dpll_d3
+ - const: dpll_d4
+ - const: dpll_d5
+ - const: dpll_d6
+ - const: dpll_d8
+ - const: dpll_d12
+ - const: dpll_d16
+ - const: gpll
+ - const: gpll_d2
+ - const: gpll_d3
+ - const: gpll_d4
+ - const: gpll_d5
+ - const: gpll_d6
+ - const: gpll_d8
+ - const: gpll_d12
+ - const: gpll_d16
+
+ "#clock-cells":
+ const: 1
+
+ "#reset-cells":
+ const: 1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - '#clock-cells'
+ - '#reset-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/zte,zx297520v3-clk.h>
+
+ topclk: clock-controller@13b000 {
+ compatible = "zte,zx297520v3-topclk", "syscon";
+ reg = <0x0013b000 0x400>;
+ clocks = <&osc26m>, <&osc32k>;
+ clock-names = "osc26m", "osc32k";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ clock-controller@1306000 {
+ compatible = "zte,zx297520v3-matrixclk", "syscon";
+ reg = <0x01306000 0x400>;
+ clocks = <&osc26m>, <&osc32k>,
+ <&topclk ZX297520V3_MPLL>, <&topclk ZX297520V3_MPLL_D2>,
+ <&topclk ZX297520V3_MPLL_D3>, <&topclk ZX297520V3_MPLL_D4>,
+ <&topclk ZX297520V3_MPLL_D5>, <&topclk ZX297520V3_MPLL_D6>,
+ <&topclk ZX297520V3_MPLL_D8>, <&topclk ZX297520V3_MPLL_D12>,
+ <&topclk ZX297520V3_MPLL_D16>, <&topclk ZX297520V3_MPLL_D26>,
+ <&topclk ZX297520V3_UPLL>, <&topclk ZX297520V3_UPLL_D2>,
+ <&topclk ZX297520V3_UPLL_D3>, <&topclk ZX297520V3_UPLL_D4>,
+ <&topclk ZX297520V3_UPLL_D5>, <&topclk ZX297520V3_UPLL_D6>,
+ <&topclk ZX297520V3_UPLL_D8>, <&topclk ZX297520V3_UPLL_D12>,
+ <&topclk ZX297520V3_UPLL_D16>,
+ <&topclk ZX297520V3_DPLL>, <&topclk ZX297520V3_DPLL_D2>,
+ <&topclk ZX297520V3_DPLL_D3>, <&topclk ZX297520V3_DPLL_D4>,
+ <&topclk ZX297520V3_DPLL_D5>, <&topclk ZX297520V3_DPLL_D6>,
+ <&topclk ZX297520V3_DPLL_D8>, <&topclk ZX297520V3_DPLL_D12>,
+ <&topclk ZX297520V3_DPLL_D16>,
+ <&topclk ZX297520V3_GPLL>, <&topclk ZX297520V3_GPLL_D2>,
+ <&topclk ZX297520V3_GPLL_D3>, <&topclk ZX297520V3_GPLL_D4>,
+ <&topclk ZX297520V3_GPLL_D5>, <&topclk ZX297520V3_GPLL_D6>,
+ <&topclk ZX297520V3_GPLL_D8>, <&topclk ZX297520V3_GPLL_D12>,
+ <&topclk ZX297520V3_GPLL_D16>;
+ clock-names = "osc26m", "osc32k", "mpll", "mpll_d2", "mpll_d3",
+ "mpll_d4", "mpll_d5", "mpll_d6", "mpll_d8", "mpll_d12",
+ "mpll_d16", "mpll_d26", "upll", "upll_d2", "upll_d3",
+ "upll_d4", "upll_d5", "upll_d6", "upll_d8", "upll_d12",
+ "upll_d16", "dpll", "dpll_d2", "dpll_d3", "dpll_d4",
+ "dpll_d5", "dpll_d6", "dpll_d8", "dpll_d12", "dpll_d16",
+ "gpll", "gpll_d2", "gpll_d3", "gpll_d4", "gpll_d5",
+ "gpll_d6", "gpll_d8", "gpll_d12", "gpll_d16";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
diff --git a/include/dt-bindings/clock/zte,zx297520v3-clk.h b/include/dt-bindings/clock/zte,zx297520v3-clk.h
index cf436ff20dfe..815e8ceeb64e 100644
--- a/include/dt-bindings/clock/zte,zx297520v3-clk.h
+++ b/include/dt-bindings/clock/zte,zx297520v3-clk.h
@@ -115,4 +115,49 @@
#define ZX297520V3_USB_RESET 18
#define ZX297520V3_HSIC_RESET 19
+#define ZX297520V3_CPU_WCLK 1
+#define ZX297520V3_CPU_PCLK 2
+#define ZX297520V3_ZSP_WCLK 3
+#define ZX297520V3_EDCP_WCLK 4
+#define ZX297520V3_EDCP_PCLK 5
+#define ZX297520V3_SD0_WCLK 6
+#define ZX297520V3_SD0_PCLK 7
+#define ZX297520V3_SD0_CDET 8
+#define ZX297520V3_SD1_WCLK 9
+#define ZX297520V3_SD1_PCLK 10
+#define ZX297520V3_SD1_CDET 11
+#define ZX297520V3_NAND_WCLK 12
+#define ZX297520V3_NAND_PCLK 13
+#define ZX297520V3_DMA_PCLK 14
+#define ZX297520V3_MBOX_PCLK 15
+#define ZX297520V3_PDCFG_WCLK 16
+#define ZX297520V3_PDCFG_PCLK 17
+#define ZX297520V3_SSC_WCLK 18
+#define ZX297520V3_SSC_PCLK 19
+#define ZX297520V3_GMAC_WCLK 20
+#define ZX297520V3_GMAC_PCLK 21
+#define ZX297520V3_GMAC_AHB 22
+#define ZX297520V3_VOU_WCLK 23
+#define ZX297520V3_VOU_PCLK 24
+#define ZX297520V3_LSP_MPLL_D5_WCLK 25
+#define ZX297520V3_LSP_MPLL_D4_WCLK 26
+#define ZX297520V3_LSP_MPLL_D6_WCLK 27
+#define ZX297520V3_LSP_MPLL_D8_WCLK 28
+#define ZX297520V3_LSP_MPLL_D12_WCLK 29
+#define ZX297520V3_LSP_OSC26M_WCLK 30
+#define ZX297520V3_LSP_OSC32K_WCLK 31
+#define ZX297520V3_LSP_PCLK 32
+#define ZX297520V3_LSP_TDM_WCLK 33
+#define ZX297520V3_LSP_DPLL_D4_WCLK 34
+
+#define ZX297520V3_CPU_RESET 0
+#define ZX297520V3_EDCP_RESET 1
+#define ZX297520V3_SD0_RESET 2
+#define ZX297520V3_SD1_RESET 3
+#define ZX297520V3_NAND_RESET 4
+#define ZX297520V3_PDCFG_RESET 5
+#define ZX297520V3_SSC_RESET 6
+#define ZX297520V3_GMAC_RESET 7
+#define ZX297520V3_VOU_RESET 8
+
#endif /* __DT_BINDINGS_CLOCK_ZX297520V3_H */
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 03/12] dt-bindings: clk: zte: Add zx297520v3 LSP clock and reset bindings
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
The clock controller of the Low Speed Peripherals is relatively clean.
One register per device with gates, muxes and resets and for some
devices a divider. There are even bits in the top controller to control
propagation of clock lines down to LSP.
The clocks are sorted by register address and I am convinced that the
device list is complete. There are however a few more registers that are
likely helper controls for the I2S and TDM devices.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
Patch changelog:
v5: Order properties compatible->reg->clocks->clock->names->#cells
---
.../bindings/clock/zte,zx297520v3-lspclk.yaml | 130 +++++++++++++++++++++
include/dt-bindings/clock/zte,zx297520v3-clk.h | 56 +++++++++
2 files changed, 186 insertions(+)
diff --git a/Documentation/devicetree/bindings/clock/zte,zx297520v3-lspclk.yaml b/Documentation/devicetree/bindings/clock/zte,zx297520v3-lspclk.yaml
new file mode 100644
index 000000000000..096295edb6e2
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/zte,zx297520v3-lspclk.yaml
@@ -0,0 +1,130 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/zte,zx297520v3-lspclk.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ZTE zx297520v3 SoC LSP clock and reset controller
+
+maintainers:
+ - Stefan Dösinger <stefandoesinger@gmail.com>
+
+description: |
+ This clock and reset controller controls low speed peripherals on the board.
+ This is a relatively isolated subsystem containing UART, I2C, I2S and SPI
+ devices. The clock controller is responsible for bringing the devices out of
+ reset and enabling their clocks as needed.
+
+ The controller receives its clock signal from the matrix controller and need
+ to be declared as clock inputs.
+
+ All available clocks are defined as preprocessor macros in the
+ 'dt-bindings/clock/zte,zx297520v3-clk.h' header.
+
+properties:
+ compatible:
+ const: zte,zx297520v3-lspclk
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Main PLL divided by 5 output from matrixclk (124.8 MHz)
+ - description: Main PLL divided by 4 output from matrixclk (156 MHz)
+ - description: Main PLL divided by 6 output from matrixclk (104 MHz)
+ - description: Main PLL divided by 8 output from matrixclk (78 MHz)
+ - description: Main PLL divided by 12 output from matrixclk (52 MHz)
+ - description: Main oscillator output from matrixclk (26 MHz)
+ - description: Timer oscillator output from matrixclk (32 KHz)
+ - description: LSP pclk output from matrixclk (26 MHz)
+ - description: TDM wclk mux output from matrixclk
+ - description: DPLL divided by 4 output from matrixclk (122.88 MHz)
+
+ clock-names:
+ items:
+ - const: mpll_d5
+ - const: mpll_d4
+ - const: mpll_d6
+ - const: mpll_d8
+ - const: mpll_d12
+ - const: osc26m
+ - const: osc32k
+ - const: pclk
+ - const: tdm_wclk
+ - const: dpll_d4
+
+ "#clock-cells":
+ const: 1
+
+ "#reset-cells":
+ const: 1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - '#clock-cells'
+ - '#reset-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/zte,zx297520v3-clk.h>
+
+ matrixclk: clock-controller@1306000 {
+ compatible = "zte,zx297520v3-matrixclk", "syscon";
+ reg = <0x01306000 0x400>;
+ clocks = <&osc26m>, <&osc32k>,
+ <&topclk ZX297520V3_MPLL>, <&topclk ZX297520V3_MPLL_D2>,
+ <&topclk ZX297520V3_MPLL_D3>, <&topclk ZX297520V3_MPLL_D4>,
+ <&topclk ZX297520V3_MPLL_D5>, <&topclk ZX297520V3_MPLL_D6>,
+ <&topclk ZX297520V3_MPLL_D8>, <&topclk ZX297520V3_MPLL_D12>,
+ <&topclk ZX297520V3_MPLL_D16>, <&topclk ZX297520V3_MPLL_D26>,
+ <&topclk ZX297520V3_UPLL>, <&topclk ZX297520V3_UPLL_D2>,
+ <&topclk ZX297520V3_UPLL_D3>, <&topclk ZX297520V3_UPLL_D4>,
+ <&topclk ZX297520V3_UPLL_D5>, <&topclk ZX297520V3_UPLL_D6>,
+ <&topclk ZX297520V3_UPLL_D8>, <&topclk ZX297520V3_UPLL_D12>,
+ <&topclk ZX297520V3_UPLL_D16>,
+ <&topclk ZX297520V3_DPLL>, <&topclk ZX297520V3_DPLL_D2>,
+ <&topclk ZX297520V3_DPLL_D3>, <&topclk ZX297520V3_DPLL_D4>,
+ <&topclk ZX297520V3_DPLL_D5>, <&topclk ZX297520V3_DPLL_D6>,
+ <&topclk ZX297520V3_DPLL_D8>, <&topclk ZX297520V3_DPLL_D12>,
+ <&topclk ZX297520V3_DPLL_D16>,
+ <&topclk ZX297520V3_GPLL>, <&topclk ZX297520V3_GPLL_D2>,
+ <&topclk ZX297520V3_GPLL_D3>, <&topclk ZX297520V3_GPLL_D4>,
+ <&topclk ZX297520V3_GPLL_D5>, <&topclk ZX297520V3_GPLL_D6>,
+ <&topclk ZX297520V3_GPLL_D8>, <&topclk ZX297520V3_GPLL_D12>,
+ <&topclk ZX297520V3_GPLL_D16>;
+ clock-names = "osc26m", "osc32k", "mpll", "mpll_d2", "mpll_d3",
+ "mpll_d4", "mpll_d5", "mpll_d6", "mpll_d8", "mpll_d12",
+ "mpll_d16", "mpll_d26", "upll", "upll_d2", "upll_d3",
+ "upll_d4", "upll_d5", "upll_d6", "upll_d8", "upll_d12",
+ "upll_d16", "dpll", "dpll_d2", "dpll_d3", "dpll_d4",
+ "dpll_d5", "dpll_d6", "dpll_d8", "dpll_d12", "dpll_d16",
+ "gpll", "gpll_d2", "gpll_d3", "gpll_d4", "gpll_d5",
+ "gpll_d6", "gpll_d8", "gpll_d12", "gpll_d16";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ clock-controller@1400000 {
+ compatible = "zte,zx297520v3-lspclk";
+ reg = <0x01400000 0x100>;
+ clocks = <&matrixclk ZX297520V3_LSP_MPLL_D5_WCLK>,
+ <&matrixclk ZX297520V3_LSP_MPLL_D4_WCLK>,
+ <&matrixclk ZX297520V3_LSP_MPLL_D6_WCLK>,
+ <&matrixclk ZX297520V3_LSP_MPLL_D8_WCLK>,
+ <&matrixclk ZX297520V3_LSP_MPLL_D12_WCLK>,
+ <&matrixclk ZX297520V3_LSP_OSC26M_WCLK>,
+ <&matrixclk ZX297520V3_LSP_OSC32K_WCLK>,
+ <&matrixclk ZX297520V3_LSP_PCLK>,
+ <&matrixclk ZX297520V3_LSP_TDM_WCLK>,
+ <&matrixclk ZX297520V3_LSP_DPLL_D4_WCLK>;
+ clock-names = "mpll_d5", "mpll_d4", "mpll_d6", "mpll_d8", "mpll_d12",
+ "osc26m", "osc32k", "pclk", "tdm_wclk", "dpll_d4";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
diff --git a/include/dt-bindings/clock/zte,zx297520v3-clk.h b/include/dt-bindings/clock/zte,zx297520v3-clk.h
index 815e8ceeb64e..57387529a708 100644
--- a/include/dt-bindings/clock/zte,zx297520v3-clk.h
+++ b/include/dt-bindings/clock/zte,zx297520v3-clk.h
@@ -160,4 +160,60 @@
#define ZX297520V3_GMAC_RESET 7
#define ZX297520V3_VOU_RESET 8
+#define ZX297520V3_TIMER_L1_WCLK 1
+#define ZX297520V3_TIMER_L1_PCLK 2
+#define ZX297520V3_WDT_L2_WCLK 3
+#define ZX297520V3_WDT_L2_PCLK 4
+#define ZX297520V3_WDT_L3_WCLK 5
+#define ZX297520V3_WDT_L3_PCLK 6
+#define ZX297520V3_PWM_WCLK 7
+#define ZX297520V3_PWM_PCLK 8
+#define ZX297520V3_I2S0_WCLK 9
+#define ZX297520V3_I2S0_PCLK 10
+#define ZX297520V3_I2S1_WCLK 11
+#define ZX297520V3_I2S1_PCLK 12
+#define ZX297520V3_QSPI_WCLK 13
+#define ZX297520V3_QSPI_PCLK 14
+#define ZX297520V3_UART1_WCLK 15
+#define ZX297520V3_UART1_PCLK 16
+#define ZX297520V3_I2C1_WCLK 17
+#define ZX297520V3_I2C1_PCLK 18
+#define ZX297520V3_SPI0_WCLK 19
+#define ZX297520V3_SPI0_PCLK 20
+#define ZX297520V3_TIMER_LB_WCLK 21
+#define ZX297520V3_TIMER_LB_PCLK 22
+#define ZX297520V3_TIMER_LC_WCLK 23
+#define ZX297520V3_TIMER_LC_PCLK 24
+#define ZX297520V3_UART2_WCLK 25
+#define ZX297520V3_UART2_PCLK 26
+#define ZX297520V3_WDT_LE_WCLK 27
+#define ZX297520V3_WDT_LE_PCLK 28
+#define ZX297520V3_TIMER_LF_WCLK 29
+#define ZX297520V3_TIMER_LF_PCLK 30
+#define ZX297520V3_SPI1_WCLK 31
+#define ZX297520V3_SPI1_PCLK 32
+#define ZX297520V3_TIMER_L11_WCLK 33
+#define ZX297520V3_TIMER_L11_PCLK 34
+#define ZX297520V3_TDM_WCLK 35
+#define ZX297520V3_TDM_PCLK 36
+
+#define ZX297520V3_TIMER_L1_RESET 0
+#define ZX297520V3_WDT_L2_RESET 1
+#define ZX297520V3_WDT_L3_RESET 2
+#define ZX297520V3_PWM_RESET 3
+#define ZX297520V3_I2S0_RESET 4
+#define ZX297520V3_I2S1_RESET 5
+#define ZX297520V3_QSPI_RESET 6
+#define ZX297520V3_UART1_RESET 7
+#define ZX297520V3_I2C1_RESET 8
+#define ZX297520V3_SPI0_RESET 9
+#define ZX297520V3_TIMER_LB_RESET 10
+#define ZX297520V3_TIMER_LC_RESET 11
+#define ZX297520V3_UART2_RESET 12
+#define ZX297520V3_WDT_LE_RESET 13
+#define ZX297520V3_TIMER_LF_RESET 14
+#define ZX297520V3_SPI1_RESET 15
+#define ZX297520V3_TIMER_L11_RESET 16
+#define ZX297520V3_TDM_RESET 17
+
#endif /* __DT_BINDINGS_CLOCK_ZX297520V3_H */
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 04/12] clk: zte: Add Clock registration infrastructure.
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
The next patches will implement the regmap clocks and PLL driver. The
actual hardware specific clock listing will live in a separate module.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
MAINTAINERS | 1 +
drivers/clk/Kconfig | 1 +
drivers/clk/Makefile | 1 +
drivers/clk/zte/Kconfig | 17 +++++
drivers/clk/zte/Makefile | 5 ++
drivers/clk/zte/clk-regmap.c | 30 +++++++++
drivers/clk/zte/clk-zx.c | 157 +++++++++++++++++++++++++++++++++++++++++++
drivers/clk/zte/clk-zx.h | 79 ++++++++++++++++++++++
drivers/clk/zte/pll-zx.c | 19 ++++++
9 files changed, 310 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 0cc1ede3c80c..f1f0459b2c72 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3870,6 +3870,7 @@ F: Documentation/devicetree/bindings/arm/zte.yaml
F: Documentation/devicetree/zte,zx297520v3-*
F: arch/arm/boot/dts/zte/
F: arch/arm/mach-zte/
+F: drivers/clk/zte/
F: include/dt-bindings/clock/zte,zx297520v3-clk.h
ARM/ZYNQ ARCHITECTURE
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 1717ce75a907..6f0a863951ca 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -545,6 +545,7 @@ source "drivers/clk/uniphier/Kconfig"
source "drivers/clk/visconti/Kconfig"
source "drivers/clk/x86/Kconfig"
source "drivers/clk/xilinx/Kconfig"
+source "drivers/clk/zte/Kconfig"
source "drivers/clk/zynqmp/Kconfig"
# Kunit test cases
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index cc108a75a900..13a5478f1112 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -167,5 +167,6 @@ ifeq ($(CONFIG_COMMON_CLK), y)
obj-$(CONFIG_X86) += x86/
endif
obj-y += xilinx/
+obj-$(CONFIG_COMMON_CLK_ZTE) += zte/
obj-$(CONFIG_ARCH_ZYNQ) += zynq/
obj-$(CONFIG_COMMON_CLK_ZYNQMP) += zynqmp/
diff --git a/drivers/clk/zte/Kconfig b/drivers/clk/zte/Kconfig
new file mode 100644
index 000000000000..b7b65a2172a9
--- /dev/null
+++ b/drivers/clk/zte/Kconfig
@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# ZTE Clock Drivers
+#
+
+config COMMON_CLK_ZTE
+ tristate "Clock driver for ZTE SoCs"
+ depends on ARCH_ZTE || COMPILE_TEST
+ default ARCH_ZTE
+ select AUXILIARY_BUS
+ select MFD_SYSCON
+ help
+ This option selects common clock infrastructure for ZTE based SoCs.
+ You will need to enable one or more SoC specific drivers to make use
+ of this.
+
+ Enable this if you are building a kernel for a ZTE designed board.
diff --git a/drivers/clk/zte/Makefile b/drivers/clk/zte/Makefile
new file mode 100644
index 000000000000..27db07293165
--- /dev/null
+++ b/drivers/clk/zte/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+obj-$(CONFIG_COMMON_CLK_ZTE) += clk-zte.o
+
+clk-zte-y += clk-zx.o pll-zx.o clk-regmap.o
diff --git a/drivers/clk/zte/clk-regmap.c b/drivers/clk/zte/clk-regmap.c
new file mode 100644
index 000000000000..7908f1562f63
--- /dev/null
+++ b/drivers/clk/zte/clk-regmap.c
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2014 MediaTek Inc.
+ * Copyright (c) 2018 BayLibre, SAS.
+ * Copyright (c) 2026 Stefan Dösinger.
+ * Author: Stefan Dösinger <stefandoesinger@gmail.com>
+ */
+
+#include "clk-zx.h"
+
+int zx_clk_register_gates(struct device *dev, struct regmap *regmap,
+ const struct zx_gate_desc *desc, unsigned int num,
+ struct clk_hw_onecell_data *clocks)
+{
+ return -ENODEV;
+}
+
+int zx_clk_register_dividers(struct device *dev, struct regmap *regmap,
+ const struct zx_div_desc *desc, unsigned int num,
+ struct clk_hw_onecell_data *clocks)
+{
+ return -ENODEV;
+}
+
+int zx_clk_register_muxes(struct device *dev, struct regmap *regmap,
+ const struct zx_mux_desc *desc, unsigned int num,
+ struct clk_hw_onecell_data *clocks)
+{
+ return -ENODEV;
+}
diff --git a/drivers/clk/zte/clk-zx.c b/drivers/clk/zte/clk-zx.c
new file mode 100644
index 000000000000..6e21c4a82a46
--- /dev/null
+++ b/drivers/clk/zte/clk-zx.c
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2026 Stefan Dösinger
+ */
+
+#include <linux/platform_device.h>
+#include <linux/auxiliary_bus.h>
+#include <linux/clk-provider.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include "clk-zx.h"
+
+static void zx_adev_release(struct device *dev)
+{
+ dev_info(dev, "Aux device released.\n");
+}
+
+static void zx_adev_unregister(void *data)
+{
+ struct auxiliary_device *adev = data;
+
+ auxiliary_device_delete(adev);
+ auxiliary_device_uninit(adev);
+}
+
+int zx_clk_probe(struct platform_device *pdev)
+{
+ unsigned int public_clk_count = 1, highest_id = 0;
+ struct clk_hw_onecell_data *clocks;
+ struct device *dev = &pdev->dev;
+ const struct zx_clk_data *data;
+ struct auxiliary_device *adev;
+ struct regmap *map;
+ struct clk *clk;
+ unsigned int i;
+ int res;
+
+ data = device_get_match_data(dev);
+ if (!data)
+ return -EINVAL;
+
+ map = device_node_to_regmap(dev->of_node);
+ if (!map)
+ return -EINVAL;
+
+ for (i = 0; i < data->num_plls; ++i) {
+ if (data->plls[i].id) {
+ unsigned int last_idx = data->plls[i].id + data->plls[i].num_postdivs - 1;
+
+ if (last_idx > highest_id)
+ highest_id = last_idx;
+ public_clk_count += data->plls[i].num_postdivs;
+ }
+ }
+ for (i = 0; i < data->num_muxes; ++i) {
+ if (data->muxes[i].id) {
+ if (data->muxes[i].id > highest_id)
+ highest_id = data->muxes[i].id;
+ public_clk_count++;
+ }
+ }
+ for (i = 0; i < data->num_divs; ++i) {
+ if (data->divs[i].id) {
+ if (data->divs[i].id > highest_id)
+ highest_id = data->divs[i].id;
+ public_clk_count++;
+ }
+ }
+ for (i = 0; i < data->num_gates; ++i) {
+ if (data->gates[i].id) {
+ if (data->gates[i].id > highest_id)
+ highest_id = data->gates[i].id;
+ public_clk_count++;
+ }
+ }
+
+ if (WARN_ON(public_clk_count != highest_id + 1))
+ return -EINVAL;
+
+ clocks = devm_kzalloc(dev, struct_size(clocks, hws, public_clk_count), GFP_KERNEL);
+ if (!clocks)
+ return -ENOMEM;
+ clocks->num = public_clk_count;
+
+ for (i = 0; i < data->num_inputs_enable; ++i) {
+ clk = devm_clk_get_enabled(dev, data->inputs_enable[i]);
+ if (IS_ERR(clk)) {
+ return dev_err_probe(dev, PTR_ERR(clk), "Input clk %s failure\n",
+ data->inputs_enable[i]);
+ }
+ }
+ for (i = 0; i < data->num_inputs; ++i) {
+ clk = devm_clk_get(dev, data->inputs[i]);
+ if (IS_ERR(clk)) {
+ return dev_err_probe(dev, PTR_ERR(clk), "Input clk %s failure\n",
+ data->inputs[i]);
+ }
+ }
+
+ res = zx_clk_register_plls(dev, map, data->plls, data->num_plls, clocks);
+ if (res)
+ return res;
+
+ res = zx_clk_register_muxes(dev, map, data->muxes, data->num_muxes, clocks);
+ if (res)
+ return res;
+
+ res = zx_clk_register_dividers(dev, map, data->divs, data->num_divs, clocks);
+ if (res)
+ return res;
+
+ res = zx_clk_register_gates(dev, map, data->gates, data->num_gates, clocks);
+ if (res)
+ return res;
+
+ /* This is to catch holes in the tables rather than registration errors. The count vs
+ * highest ID should catch most static issues. This check here will trigger if an ID is
+ * reused by accident.
+ */
+ for (i = 1; i < public_clk_count; i++) {
+ if (WARN(!clocks->hws[i], "Clock %u not registered\n", i))
+ return -EINVAL;
+ }
+
+ res = devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, clocks);
+ if (res)
+ return res;
+
+ adev = devm_kzalloc(dev, sizeof(*adev), GFP_KERNEL);
+ if (!adev)
+ return -ENOMEM;
+
+ adev->name = data->reset_auxdev_name;
+ adev->dev.parent = dev;
+ adev->dev.release = zx_adev_release;
+ adev->dev.of_node = dev->of_node;
+
+ res = auxiliary_device_init(adev);
+ if (res)
+ return dev_err_probe(dev, res, "Failed to init aux dev %s\n", adev->name);
+
+ res = auxiliary_device_add(adev);
+ if (res) {
+ auxiliary_device_uninit(adev);
+ return dev_err_probe(dev, res, "Failed to add aux dev %s\n", adev->name);
+ }
+
+ return devm_add_action_or_reset(dev, zx_adev_unregister, adev);
+}
+EXPORT_SYMBOL_NS_GPL(zx_clk_probe, "ZTE_CLK");
+
+MODULE_AUTHOR("Stefan Dösinger <stefandoesinger@gmail.com>");
+MODULE_DESCRIPTION("ZTE common clock driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/clk/zte/clk-zx.h b/drivers/clk/zte/clk-zx.h
new file mode 100644
index 000000000000..b39bbed2d420
--- /dev/null
+++ b/drivers/clk/zte/clk-zx.h
@@ -0,0 +1,79 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2026 Stefan Dösinger
+ */
+
+#ifndef __DRV_CLK_ZX_H
+#define __DRV_CLK_ZX_H
+
+#include <linux/platform_device.h>
+#include <linux/clk-provider.h>
+#include <linux/regmap.h>
+
+struct zx_pll_desc {
+ unsigned int id;
+ const char *name;
+ const char * const *parents;
+ unsigned int num_parents;
+ unsigned long rate;
+ const unsigned int *postdivs;
+ unsigned int num_postdivs;
+ u16 reg;
+};
+
+struct zx_mux_desc {
+ unsigned int id;
+ const char *name;
+ const char * const *parents;
+ unsigned int num_parents;
+ u16 reg;
+ u8 shift, size;
+};
+
+struct zx_div_desc {
+ unsigned int id;
+ const char *name, *parent;
+ u16 reg;
+ u8 shift, size;
+};
+
+struct zx_gate_desc {
+ unsigned int id;
+ const char *name, *parent;
+ unsigned long flags;
+ u16 reg;
+ u8 shift;
+};
+
+int zx_clk_register_plls(struct device *dev, struct regmap *regmap,
+ const struct zx_pll_desc *desc, unsigned int num,
+ struct clk_hw_onecell_data *clocks);
+int zx_clk_register_muxes(struct device *dev, struct regmap *regmap,
+ const struct zx_mux_desc *desc, unsigned int num,
+ struct clk_hw_onecell_data *clocks);
+int zx_clk_register_dividers(struct device *dev, struct regmap *regmap,
+ const struct zx_div_desc *desc, unsigned int num,
+ struct clk_hw_onecell_data *clocks);
+int zx_clk_register_gates(struct device *dev, struct regmap *regmap,
+ const struct zx_gate_desc *desc, unsigned int num,
+ struct clk_hw_onecell_data *clocks);
+
+struct zx_clk_data {
+ const char * const *inputs_enable;
+ unsigned int num_inputs_enable;
+ const char * const *inputs;
+ unsigned int num_inputs;
+ const struct zx_pll_desc *plls;
+ unsigned int num_plls;
+ const struct zx_mux_desc *muxes;
+ unsigned int num_muxes;
+ const struct zx_div_desc *divs;
+ unsigned int num_divs;
+ const struct zx_gate_desc *gates;
+ unsigned int num_gates;
+ const char *reset_auxdev_name;
+};
+
+int zx_clk_probe(struct platform_device *pdev);
+
+#endif /* __DRV_CLK_ZX_H */
diff --git a/drivers/clk/zte/pll-zx.c b/drivers/clk/zte/pll-zx.c
new file mode 100644
index 000000000000..c0475d5441fb
--- /dev/null
+++ b/drivers/clk/zte/pll-zx.c
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2026 Stefan Dösinger
+ */
+#include <linux/clk-provider.h>
+#include <linux/rational.h>
+#include <linux/device.h>
+#include <linux/regmap.h>
+#include <linux/units.h>
+#include <linux/clk.h>
+
+#include "clk-zx.h"
+
+int zx_clk_register_plls(struct device *dev, struct regmap *regmap,
+ const struct zx_pll_desc *desc, unsigned int num,
+ struct clk_hw_onecell_data *clocks)
+{
+ return -ENODEV;
+}
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 05/12] clk: zte: Add zx PLL support infrastructure
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
I am guessing how much of this is reusable among other zx chips or even
differently named ZTE platforms (if there are any). From reading the old
zx2967 code, I think the PLL code would be reusable there, maybe with
platform specific bitmasks but otherwise the same logic.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
drivers/clk/zte/pll-zx.c | 460 ++++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 459 insertions(+), 1 deletion(-)
diff --git a/drivers/clk/zte/pll-zx.c b/drivers/clk/zte/pll-zx.c
index c0475d5441fb..f077b6b56841 100644
--- a/drivers/clk/zte/pll-zx.c
+++ b/drivers/clk/zte/pll-zx.c
@@ -11,9 +11,467 @@
#include "clk-zx.h"
+/* This code has only been tested with zx297520v3 PLLs, but from reading the zx296718 clock code it
+ * looks like PLL registers are similar. ZTE's sources explain the PLL register contents only in a
+ * .cmm file (A Lauterback TRACE32 script) and some unused headers in their U-Boot code dump, which
+ * may not be accurate. When calculating the frequencies from the default PLL configuration the
+ * results match the fixed rate clocks from their clock driver.
+ *
+ * The 26mhz and 32khz clocks can be easily observed with the timers. The 104mhz output can be
+ * observed through the UART. One 122.88 PLL can be observed through the TDM device. All others can
+ * only be indirectly infered, e.g. by comparing CPU speed or SDIO transfer rate between the fixed
+ * 26 MHz oscillator and the provided PLL frequency.
+ *
+ * The formula to calculate the clock is ((ref / refdiv) * fbdiv) / postdiv1 / postdiv2. The masks
+ * are given below. There are a few control flags:
+ *
+ * Bit 31: Disables the PLL, but passes the reference through unmodified. If POSTDIV_OUT_DISABLE
+ * still matters is different between PLLs.
+ * Bit 30: Returns if the PLL is locked
+ * Bit 29: Not named in ZTE's code, but can be set. There is no obvious impact. Lock times are
+ * unchanged, so it doesn't influence or bypass lock detection. It doesn't raise any IRQs or
+ * influence GPIOs.
+ * Bit 27: Given its name it likely disables the Delta-Sigma Modulator, if one exists at all. The
+ * boot ROM sets it on every PLL. Unsetting it marginally decreases the time it takes to
+ * lock to the reference clock (from ~400us to ~300us). Regardless of this bit I could not
+ * make the supposed fractional part in register 2 work.
+ * Bit 24: Bypasses the VCO, but still applies refdiv and postdiv. Doesn't matter if PLL_DISABLE=1.
+ */
+
+#define ZX29_PLL_DISABLE BIT(31)
+#define ZX29_PLL_LOCKED BIT(30)
+#define ZX29_PLL_LOCK_FILTER BIT(29)
+#define ZX29_PLL_DSM_DISABLE BIT(27)
+#define ZX29_PLL_PARENT_MASK GENMASK(26, 25)
+#define ZX29_PLL_PARENT_SHIFT 25
+#define ZX29_PLL_BYPASS BIT(24)
+#define ZX29_PLL_REFDIV_MASK GENMASK(23, 18)
+#define ZX29_PLL_REFDIV_SHIFT 18
+#define ZX29_PLL_FBDIV_MASK GENMASK(17, 6)
+#define ZX29_PLL_FBDIV_SHIFT 6
+#define ZX29_PLL_POSTDIV1_MASK GENMASK(5, 3)
+#define ZX29_PLL_POSTDIV1_SHIFT 3
+#define ZX29_PLL_POSTDIV2_MASK GENMASK(2, 0)
+#define ZX29_PLL_POSTDIV2_SHIFT 0
+
+/* The second register is supposed to have another 24 bit value that gets added to fbdiv but it is
+ * always 0 in the preconfigured values. I could not observe any effect from setting it to something
+ * other than 0, regardless of the DSM disable bit. It is possible that it is only supported by
+ * dpll, which is a possible parent for i2s.
+ *
+ * Bits 28:25 contain more flags:
+ *
+ * Bit 27: Setting ZX29_PLL_DACAP slows down the lock time and obivates the speed gained from
+ * !DSM_DISABLE. No other effect observed.
+ *
+ * Bit 26: ZX29_PLL_4PHASE_OUT_DISABLE is set on some PLLs on boot but not on others. It is set on
+ * boot on mpll and upll, but not gpll, dpll or unknownpll. I am not sure what it does
+ * either. The SDIO devices break if they are fed from gpll with this flag set, but they
+ * work ok if they are fed from mpll without this flag set.
+ *
+ * Bit 25: ZX29_PLL_POSTDIV_OUT_DISABLE seems to disable the PLL output entirely. Whether it is
+ * bypassed by PLL_DISABLE differs between PLLs. gpll still produces an output clock if
+ * PLL_DISABLE = 1 and POSTDIV_DISABLE = 1, but produces no output if PLL_DISABLE = 0 and
+ * POSTDIV_DISABLE = 1. The dpll feeder ("unknownpll") at 0x100 produces no output clock
+ * if both PLL_DISABLE and POSTDIV_DISABLE are set to 1.
+ *
+ * Bit 24: ZX29_PLL_VCO_OUT_DISABLE probably disables the output of the VCO clock without
+ * post-VCO-dividers, but the raw VCO output is not a possible parent of any consumer clock,
+ * so I could not confirm this. It does not disable the VCO entirely - that's what
+ * PLL_DISABLE does.
+ *
+ * A spinlock should not be needed. PLLs don't share their registers with anything else and the
+ * global prepare mutex and enable spinlock should be enough. Beware of conflicts in reg2 between
+ * POSTDIV_OUT_DISABLE and the fractional value in case you find out how fractional dividers work
+ * and add support for them.
+ */
+#define ZX29_PLL_REG2_OFFSET 4
+#define ZX29_PLL_DACAP BIT(27)
+#define ZX29_PLL_4PHASE_OUT_DISABLE BIT(26)
+#define ZX29_PLL_POSTDIV_OUT_DISABLE BIT(25)
+#define ZX29_PLL_VCO_OUT_DISABLE BIT(24)
+
+/* The VCO's frequency range is limited. The stock settings run the VCO between 960 and 1248 MHz.
+ * Ad-hoc testing with gpll suggests that at least this PLL remains stable down to about 7 MHz and
+ * up to 2 GHz and produces a clock that can be used by the SDIO controller. Attempting to run the
+ * mpll VCO at 624 MHz and setting postdiv1 = postdiv2 = 1 - which should result in the same output
+ * frequency - or running it at 1872 MHz with an effective post divider of 3 crashes the CPU. Most
+ * likely the PLLs become unstable outside their core range and the SDIO controller is much more
+ * forgiving than CPU and DRAM are.
+ */
+#define ZX29_PLL_VCO_MAX_FREQ (1300*HZ_PER_MHZ)
+#define ZX29_PLL_VCO_MIN_FREQ (900*HZ_PER_MHZ)
+
+struct zx29_clk_pll {
+ struct clk_hw hw;
+ struct device *dev;
+ struct regmap *map;
+ unsigned long init_rate;
+ u16 reg;
+};
+
+static inline struct zx29_clk_pll *to_zx29_clk_pll(struct clk_hw *hw)
+{
+ return container_of(hw, struct zx29_clk_pll, hw);
+}
+
+static int zx29_pll_is_prepared(struct clk_hw *hw)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+ int res;
+
+ res = regmap_test_bits(pll->map, pll->reg, ZX29_PLL_DISABLE);
+ if (res < 0)
+ return res;
+
+ return !res;
+}
+
+static int zx29_pll_prepare(struct clk_hw *hw)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+ u32 val;
+ int res;
+
+ res = regmap_clear_bits(pll->map, pll->reg, ZX29_PLL_DISABLE);
+ if (res < 0)
+ return res;
+
+ /* Lock duration is usually between 300us to 500us */
+ res = regmap_read_poll_timeout(pll->map, pll->reg, val, val & ZX29_PLL_LOCKED, 50, 2000);
+ dev_dbg(pll->dev, "%s: Enable result %u val 0x%08x\n", clk_hw_get_name(&pll->hw), res, val);
+ return res;
+}
+
+static void zx29_pll_unprepare(struct clk_hw *hw)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+
+ regmap_set_bits(pll->map, pll->reg, ZX29_PLL_DISABLE);
+}
+
+static int zx29_pll_is_enabled(struct clk_hw *hw)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+ int res;
+
+ res = regmap_test_bits(pll->map, pll->reg + ZX29_PLL_REG2_OFFSET,
+ ZX29_PLL_POSTDIV_OUT_DISABLE);
+ if (res < 0)
+ return res;
+
+ return !res;
+}
+
+static int zx29_pll_enable(struct clk_hw *hw)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+
+ return regmap_clear_bits(pll->map, pll->reg + ZX29_PLL_REG2_OFFSET,
+ ZX29_PLL_POSTDIV_OUT_DISABLE);
+}
+
+static void zx29_pll_disable(struct clk_hw *hw)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+
+ regmap_set_bits(pll->map, pll->reg + ZX29_PLL_REG2_OFFSET,
+ ZX29_PLL_POSTDIV_OUT_DISABLE);
+}
+
+static unsigned long zx29_pll_get_rate(const struct zx29_clk_pll *pll, unsigned long parent_rate,
+ u32 setting)
+{
+ unsigned long refdiv, fbdiv, postdiv1, postdiv2, freq;
+ const char *name = clk_hw_get_name(&pll->hw);
+ u64 vco;
+
+ refdiv = (setting & ZX29_PLL_REFDIV_MASK) >> ZX29_PLL_REFDIV_SHIFT;
+ fbdiv = (setting & ZX29_PLL_FBDIV_MASK) >> ZX29_PLL_FBDIV_SHIFT;
+ postdiv1 = (setting & ZX29_PLL_POSTDIV1_MASK) >> ZX29_PLL_POSTDIV1_SHIFT;
+ postdiv2 = (setting & ZX29_PLL_POSTDIV2_MASK) >> ZX29_PLL_POSTDIV2_SHIFT;
+ dev_dbg(pll->dev, "%s: reference clock %lu HZ, PLL setting 0x%08x\n",
+ name, parent_rate, setting);
+
+ if (!refdiv || !postdiv1 || !postdiv2) {
+ dev_err(pll->dev, "%s: divide by zero (%lu, %lu, %lu)\n", name, refdiv, postdiv1,
+ postdiv2);
+ return 0;
+ }
+
+ vco = div_u64((u64)parent_rate * fbdiv, refdiv);
+ freq = div_u64(div_u64(vco, postdiv1), postdiv2);
+ dev_dbg(pll->dev, "%s: refdiv %lu fbdiv %lu\n", name, refdiv, fbdiv);
+ dev_dbg(pll->dev, "%s: postdiv1 %lu postdiv2 %lu\n", name, postdiv1, postdiv2);
+
+ dev_dbg(pll->dev, "%s: %lu MHZ\n", name, freq / HZ_PER_MHZ);
+
+ return freq;
+}
+
+static unsigned long zx29_pll_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+ u32 val;
+ int res;
+
+ res = regmap_read(pll->map, pll->reg, &val);
+ if (res < 0)
+ return res;
+
+ return zx29_pll_get_rate(pll, parent_rate, val);
+}
+
+static u32 zx29_pll_calc_values(const struct zx29_clk_pll *pll, unsigned long parent_rate,
+ unsigned long rate)
+{
+ const unsigned int postdiv1_max = (1 << hweight32(ZX29_PLL_POSTDIV1_MASK)) - 1;
+ const unsigned int postdiv2_max = (1 << hweight32(ZX29_PLL_POSTDIV2_MASK)) - 1;
+ unsigned long fbdiv, refdiv, best_fbdiv = 0, best_refdiv = 0;
+ u32 postdiv1 = 0, postdiv2 = 0, i, j, setting;
+ const char *name = clk_hw_get_name(&pll->hw);
+ long best = LONG_MAX;
+
+ /* This code produces the same VCO settings that the boot loader and stock firmware use for
+ * the standard frequencies. It has seen only very little manual testing beyond that.
+ *
+ * The goal is to find a VCO setting that gets us as close as possible to the desired output
+ * rate, while being within the VCO's operating limits and achievable with the input value
+ * range. It is iterating over possible post-VCO diver values (1-7)*(1-7) to look for valid
+ * VCO target frequencies and then looks for refdiv and fbdiv values to achieve the VCO
+ * frequency from the reference frequency.
+ */
+ for (j = 1; j <= postdiv2_max; j++) {
+ for (i = 1; i <= postdiv1_max; i++) {
+ u64 vco = (u64)rate * i * j;
+ long out;
+
+ if (vco > ZX29_PLL_VCO_MAX_FREQ || vco < ZX29_PLL_VCO_MIN_FREQ)
+ continue;
+
+ rational_best_approximation(vco, parent_rate,
+ (1 << hweight32(ZX29_PLL_FBDIV_MASK)) - 1,
+ (1 << hweight32(ZX29_PLL_REFDIV_MASK)) - 1,
+ &fbdiv, &refdiv);
+ setting = fbdiv << ZX29_PLL_FBDIV_SHIFT;
+ setting |= refdiv << ZX29_PLL_REFDIV_SHIFT;
+ setting |= i << ZX29_PLL_POSTDIV1_SHIFT;
+ setting |= j << ZX29_PLL_POSTDIV2_SHIFT;
+ out = zx29_pll_get_rate(pll, parent_rate, setting);
+
+ if (abs(out - rate) > best)
+ continue;
+
+ if (abs(out - rate) < best) {
+ postdiv1 = i;
+ postdiv2 = j;
+ best_fbdiv = fbdiv;
+ best_refdiv = refdiv;
+ best = abs(out - rate);
+
+ if (!best)
+ goto search_done;
+ }
+ }
+ }
+search_done:
+
+ if (!postdiv1) {
+ dev_err(pll->dev, "Did not find a setting for %lu Hz, parent %lu Hz\n",
+ rate, parent_rate);
+ return 0;
+ }
+
+ dev_dbg(pll->dev, "%s: parent rate %lu\n", name, parent_rate);
+ dev_dbg(pll->dev, "%s: found VCO dividers %u and %u\n", name, postdiv1, postdiv2);
+ dev_dbg(pll->dev, "%s: VCO target rate %lu\n", name, rate * postdiv1 * postdiv2);
+
+ dev_dbg(pll->dev, "%s: Got fbdiv = %lu refdiv = %lu\n", name, best_fbdiv, best_refdiv);
+
+ setting = best_fbdiv << ZX29_PLL_FBDIV_SHIFT;
+ setting |= best_refdiv << ZX29_PLL_REFDIV_SHIFT;
+ setting |= postdiv1 << ZX29_PLL_POSTDIV1_SHIFT;
+ setting |= postdiv2 << ZX29_PLL_POSTDIV2_SHIFT;
+ dev_dbg(pll->dev, "%s: Final setting 0x%08x\n", name, setting);
+
+ return setting;
+}
+
+static int zx29_pll_determine_rate(struct clk_hw *hw, struct clk_rate_request *req)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+ unsigned long new_rate, parent_rate = clk_hw_get_rate(clk_hw_get_parent(&pll->hw));
+ u32 setting;
+
+ setting = zx29_pll_calc_values(pll, parent_rate, req->rate);
+ if (!setting)
+ return -EINVAL;
+
+ new_rate = zx29_pll_get_rate(pll, parent_rate, setting);
+ if (new_rate != req->rate) {
+ dev_warn(pll->dev, "Did not find an exact match. Want %lu, got %lu\n",
+ req->rate, new_rate);
+ req->rate = new_rate;
+ }
+
+ return 0;
+}
+
+static int zx29_pll_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+ int res = -EINVAL;
+ u32 setting;
+
+ setting = zx29_pll_calc_values(pll, parent_rate, rate);
+ if (zx29_pll_get_rate(pll, parent_rate, setting) == rate) {
+ res = regmap_update_bits(pll->map, pll->reg, 0x00ffffff, setting);
+ dev_info(pll->dev, "%s: Setting rate: 0x%08x\n", clk_hw_get_name(hw), setting);
+ }
+
+ return res;
+}
+
+static u8 zx29_pll_get_parent(struct clk_hw *hw)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+ u32 val;
+ int res;
+
+ res = regmap_read(pll->map, pll->reg, &val);
+ if (res < 0)
+ return 0xff;
+
+ val = (val & ZX29_PLL_PARENT_MASK) >> ZX29_PLL_PARENT_SHIFT;
+ dev_dbg(pll->dev, "%s: Parent 0x%x\n", clk_hw_get_name(hw), val);
+
+ return val;
+}
+
+static int zx29_pll_set_parent(struct clk_hw *hw, u8 index)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+ u32 idx_shift = index << ZX29_PLL_PARENT_SHIFT;
+ int res;
+ u32 val;
+
+ res = regmap_update_bits(pll->map, pll->reg, ZX29_PLL_PARENT_MASK, idx_shift);
+ if (res < 0)
+ return res;
+
+ res = regmap_read(pll->map, pll->reg, &val);
+ if (res < 0)
+ return res;
+
+ if ((val & ZX29_PLL_PARENT_MASK) != idx_shift) {
+ dev_err(pll->dev, "Hardware rejected PLL parent %u\n", index);
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static int zx29_pll_init(struct clk_hw *hw)
+{
+ struct zx29_clk_pll *pll = to_zx29_clk_pll(hw);
+ const char *name = clk_hw_get_name(hw);
+ int res;
+
+ dev_dbg(pll->dev, "%s: initializing\n", name);
+
+ /* Remove the bypass flag so we don't have to bother with it in enable/disable. I have
+ * never seen it set by the earlier boot stages anyhow.
+ */
+ res = regmap_clear_bits(pll->map, pll->reg, ZX29_PLL_BYPASS);
+ if (res < 0)
+ return res;
+
+ if (regmap_test_bits(pll->map, pll->reg, ZX29_PLL_DISABLE) > 0) {
+ if (pll->init_rate) {
+ dev_dbg(pll->dev, "%s: Setting to %lu Hz\n", name, pll->init_rate);
+ res = clk_set_rate(pll->hw.clk, pll->init_rate);
+ if (res) {
+ dev_err(pll->dev, "%s: Failed to set rate.\n", name);
+ return res;
+ }
+ }
+
+ /* Set ZX29_PLL_POSTDIV_OUT_DISABLE for PLLs that have ZX29_PLL_DISABLE for
+ * consistency with .enable and .prepare. This ensures that .prepare doesn't
+ * inadvertedly enable PLLs without .enable being called.
+ */
+ res = regmap_set_bits(pll->map, pll->reg + ZX29_PLL_REG2_OFFSET,
+ ZX29_PLL_POSTDIV_OUT_DISABLE);
+ if (res < 0)
+ return res;
+ }
+
+ return 0;
+}
+
+const struct clk_ops zx29_pll_ops = {
+ .init = zx29_pll_init,
+ .is_prepared = zx29_pll_is_prepared,
+ .prepare = zx29_pll_prepare,
+ .unprepare = zx29_pll_unprepare,
+ .is_enabled = zx29_pll_is_enabled,
+ .enable = zx29_pll_enable,
+ .disable = zx29_pll_disable,
+ .recalc_rate = zx29_pll_recalc_rate,
+ .determine_rate = zx29_pll_determine_rate,
+ .get_parent = zx29_pll_get_parent,
+ .set_parent = zx29_pll_set_parent,
+ .set_rate = zx29_pll_set_rate,
+};
+
int zx_clk_register_plls(struct device *dev, struct regmap *regmap,
const struct zx_pll_desc *desc, unsigned int num,
struct clk_hw_onecell_data *clocks)
{
- return -ENODEV;
+ struct zx29_clk_pll *pll;
+ unsigned int i, f;
+ struct clk_hw *hw;
+ char plldiv[32];
+ int res;
+
+ for (i = 0; i < num; ++i) {
+ struct clk_init_data init = {};
+
+ pll = devm_kzalloc(dev, sizeof(*pll), GFP_KERNEL);
+ if (!pll)
+ return -ENOMEM;
+
+ init.name = desc[i].name;
+ init.ops = &zx29_pll_ops;
+ init.parent_names = desc[i].parents;
+ init.num_parents = desc[i].num_parents;
+ pll->hw.init = &init;
+ pll->map = regmap;
+ pll->reg = desc[i].reg;
+ pll->init_rate = desc[i].rate;
+
+ res = devm_clk_hw_register(dev, &pll->hw);
+ if (res)
+ return res;
+ if (desc[i].id && desc[i].postdivs && desc[i].postdivs[0] == 1)
+ clocks->hws[desc[i].id] = &pll->hw;
+
+ for (f = 0; f < desc[i].num_postdivs; ++f) {
+ if (desc[i].postdivs[f] == 1)
+ continue;
+
+ snprintf(plldiv, sizeof(plldiv), "%s_d%u", desc[i].name,
+ desc[i].postdivs[f]);
+ hw = devm_clk_hw_register_fixed_factor(dev, plldiv, desc[i].name,
+ 0, 1, desc[i].postdivs[f]);
+ if (IS_ERR(hw))
+ return PTR_ERR(hw);
+ dev_dbg(pll->dev, "%s: %lu hz\n", clk_hw_get_name(hw), clk_hw_get_rate(hw));
+
+ if (desc[i].id)
+ clocks->hws[desc[i].id + f] = hw;
+ }
+ }
+
+ return 0;
}
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 06/12] clk: zte: Add regmap based clocks
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
This is based on meson/clk-regmap.c, although slightly simplified. I
have kept the copyright lines at the top of the file to indicate its
origin.
I see that numerous clock drivers have their own incarnation of regmap
based mux/div/gate clocks. If there is any version of it that is likely
to be elevated to shared code liks clk-gate.c I'll copy that and try to
use it as unmodified as possible.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
drivers/clk/zte/clk-regmap.c | 223 ++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 220 insertions(+), 3 deletions(-)
diff --git a/drivers/clk/zte/clk-regmap.c b/drivers/clk/zte/clk-regmap.c
index 7908f1562f63..d9459417d17d 100644
--- a/drivers/clk/zte/clk-regmap.c
+++ b/drivers/clk/zte/clk-regmap.c
@@ -6,25 +6,242 @@
* Author: Stefan Dösinger <stefandoesinger@gmail.com>
*/
+#include <linux/clk-provider.h>
+#include <linux/regmap.h>
+#include <linux/device.h>
+
#include "clk-zx.h"
+struct zte_clk_regmap {
+ struct clk_hw hw;
+ struct regmap *map;
+ u16 reg;
+ u8 shift;
+ u8 size;
+};
+
+static inline struct zte_clk_regmap *to_zte_clk_regmap(struct clk_hw *hw)
+{
+ return container_of(hw, struct zte_clk_regmap, hw);
+}
+
+static int zte_clk_regmap_gate_enable(struct clk_hw *hw)
+{
+ struct zte_clk_regmap *clk = to_zte_clk_regmap(hw);
+
+ return regmap_set_bits(clk->map, clk->reg, BIT(clk->shift));
+}
+
+static void zte_clk_regmap_gate_disable(struct clk_hw *hw)
+{
+ struct zte_clk_regmap *clk = to_zte_clk_regmap(hw);
+
+ regmap_clear_bits(clk->map, clk->reg, BIT(clk->shift));
+}
+
+static int zte_clk_regmap_gate_is_enabled(struct clk_hw *hw)
+{
+ struct zte_clk_regmap *clk = to_zte_clk_regmap(hw);
+ u32 val;
+
+ regmap_read(clk->map, clk->reg, &val);
+ return !!val;
+}
+
+static const struct clk_ops zte_clk_regmap_gate_ops = {
+ .enable = zte_clk_regmap_gate_enable,
+ .disable = zte_clk_regmap_gate_disable,
+ .is_enabled = zte_clk_regmap_gate_is_enabled,
+};
+
int zx_clk_register_gates(struct device *dev, struct regmap *regmap,
const struct zx_gate_desc *desc, unsigned int num,
struct clk_hw_onecell_data *clocks)
{
- return -ENODEV;
+ struct zte_clk_regmap *clk;
+ unsigned int i;
+ int res;
+
+ for (i = 0; i < num; ++i) {
+ struct clk_init_data init = {};
+
+ clk = devm_kzalloc(dev, sizeof(*clk), GFP_KERNEL);
+ if (!clk)
+ return -ENOMEM;
+
+ init.name = desc[i].name;
+ init.ops = &zte_clk_regmap_gate_ops;
+ init.parent_names = &desc[i].parent;
+ init.num_parents = 1;
+ init.flags = CLK_SET_RATE_PARENT | desc[i].flags;
+ clk->hw.init = &init;
+ clk->map = regmap;
+ clk->reg = desc[i].reg;
+ clk->shift = desc[i].shift;
+ clk->size = 1;
+
+ res = devm_clk_hw_register(dev, &clk->hw);
+ if (res)
+ return dev_err_probe(dev, res, "Failed to register clk %s\n", desc[i].name);
+
+ if (desc[i].id)
+ clocks->hws[desc[i].id] = &clk->hw;
+ }
+
+ return 0;
+}
+
+static unsigned long zte_clk_regmap_div_recalc_rate(struct clk_hw *hw,
+ unsigned long prate)
+{
+ struct zte_clk_regmap *clk = to_zte_clk_regmap(hw);
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(clk->map, clk->reg, &val);
+ if (ret)
+ /* Gives a hint that something is wrong */
+ return 0;
+
+ val >>= clk->shift;
+ val &= clk_div_mask(clk->size);
+ return divider_recalc_rate(hw, prate, val, NULL, 0, clk->size);
}
+static int zte_clk_regmap_div_determine_rate(struct clk_hw *hw,
+ struct clk_rate_request *req)
+{
+ struct zte_clk_regmap *clk = to_zte_clk_regmap(hw);
+
+ return divider_determine_rate(hw, req, NULL, clk->size, 0);
+}
+
+static int zte_clk_regmap_div_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct zte_clk_regmap *clk = to_zte_clk_regmap(hw);
+ unsigned int val;
+ int ret;
+
+ ret = divider_get_val(rate, parent_rate, NULL, clk->size, 0);
+ if (ret < 0)
+ return ret;
+
+ val = (unsigned int)ret << clk->shift;
+ return regmap_update_bits(clk->map, clk->reg, clk_div_mask(clk->size) << clk->shift, val);
+};
+
+static const struct clk_ops zte_clk_regmap_divider_ops = {
+ .recalc_rate = zte_clk_regmap_div_recalc_rate,
+ .determine_rate = zte_clk_regmap_div_determine_rate,
+ .set_rate = zte_clk_regmap_div_set_rate,
+};
+
int zx_clk_register_dividers(struct device *dev, struct regmap *regmap,
const struct zx_div_desc *desc, unsigned int num,
struct clk_hw_onecell_data *clocks)
{
- return -ENODEV;
+ struct zte_clk_regmap *clk;
+ unsigned int i;
+ int res;
+
+ for (i = 0; i < num; ++i) {
+ struct clk_init_data init = {};
+
+ clk = devm_kzalloc(dev, sizeof(*clk), GFP_KERNEL);
+ if (!clk)
+ return -ENOMEM;
+
+ init.name = desc[i].name;
+ init.ops = &zte_clk_regmap_divider_ops;
+ init.parent_names = &desc[i].parent;
+ init.num_parents = 1;
+ init.flags = CLK_SET_RATE_PARENT;
+ clk->hw.init = &init;
+ clk->map = regmap;
+ clk->reg = desc[i].reg;
+ clk->shift = desc[i].shift;
+ clk->size = desc[i].size;
+
+ res = devm_clk_hw_register(dev, &clk->hw);
+ if (res)
+ return dev_err_probe(dev, res, "Failed to register clk %s\n", desc[i].name);
+
+ if (desc[i].id)
+ clocks->hws[desc[i].id] = &clk->hw;
+ }
+
+ return 0;
}
+static u8 zte_clk_regmap_mux_get_parent(struct clk_hw *hw)
+{
+ struct zte_clk_regmap *clk = to_zte_clk_regmap(hw);
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(clk->map, clk->reg, &val);
+ if (ret)
+ return 0xff;
+
+ val >>= clk->shift;
+ val &= GENMASK(clk->size - 1, 0);
+ return clk_mux_val_to_index(hw, NULL, 0, val);
+}
+
+static int zte_clk_regmap_mux_set_parent(struct clk_hw *hw, u8 index)
+{
+ struct zte_clk_regmap *clk = to_zte_clk_regmap(hw);
+ unsigned int val = clk_mux_index_to_val(NULL, 0, index);
+
+ return regmap_update_bits(clk->map, clk->reg,
+ GENMASK(clk->size - 1, 0) << clk->shift,
+ val << clk->shift);
+}
+
+static int zte_clk_regmap_mux_determine_rate(struct clk_hw *hw, struct clk_rate_request *req)
+{
+ return clk_mux_determine_rate_flags(hw, req, 0);
+}
+
+static const struct clk_ops zte_clk_regmap_mux_ops = {
+ .get_parent = zte_clk_regmap_mux_get_parent,
+ .set_parent = zte_clk_regmap_mux_set_parent,
+ .determine_rate = zte_clk_regmap_mux_determine_rate,
+};
+
int zx_clk_register_muxes(struct device *dev, struct regmap *regmap,
const struct zx_mux_desc *desc, unsigned int num,
struct clk_hw_onecell_data *clocks)
{
- return -ENODEV;
+ struct zte_clk_regmap *clk;
+ unsigned int i;
+ int res;
+
+ for (i = 0; i < num; ++i) {
+ struct clk_init_data init = {};
+
+ clk = devm_kzalloc(dev, sizeof(*clk), GFP_KERNEL);
+ if (!clk)
+ return -ENOMEM;
+
+ init.name = desc[i].name;
+ init.ops = &zte_clk_regmap_mux_ops;
+ init.parent_names = desc[i].parents;
+ init.num_parents = desc[i].num_parents;
+ clk->hw.init = &init;
+ clk->map = regmap;
+ clk->reg = desc[i].reg;
+ clk->shift = desc[i].shift;
+ clk->size = desc[i].size;
+
+ res = devm_clk_hw_register(dev, &clk->hw);
+ if (res)
+ return dev_err_probe(dev, res, "Failed to register clk %s\n", desc[i].name);
+
+ if (desc[i].id)
+ clocks->hws[desc[i].id] = &clk->hw;
+ }
+
+ return 0;
}
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 07/12] clk: zte: Introduce a driver for zx297520v3 top clocks
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
This register space controls core devices: PLLs, the AHB bus, a lot of
timers, the USB controller, the Cortex M0 processor that boots the board
and a few other devices. For some reason the LTE coprocessor is also
partially controlled by it. The main application processor and DDR
memory are not found here though.
The register to reboot the board is found here, as well as a register to
control of watchdog expiries cause a board reset.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
drivers/clk/zte/Kconfig | 11 +
drivers/clk/zte/Makefile | 1 +
drivers/clk/zte/clk-zx297520v3.c | 431 +++++++++++++++++++++++++++++++++++++++
3 files changed, 443 insertions(+)
diff --git a/drivers/clk/zte/Kconfig b/drivers/clk/zte/Kconfig
index b7b65a2172a9..12906212ec1e 100644
--- a/drivers/clk/zte/Kconfig
+++ b/drivers/clk/zte/Kconfig
@@ -15,3 +15,14 @@ config COMMON_CLK_ZTE
of this.
Enable this if you are building a kernel for a ZTE designed board.
+
+config CLK_ZTE_ZX297520V3
+ tristate "Clock driver for ZTE zx297520v3 based SoCs"
+ depends on COMMON_CLK_ZTE
+ default SOC_ZX297520V3
+ help
+ This driver supports ZTE zx297520v3 basic clocks.
+
+ Enable this if you want to build a kernel that is able to run on
+ boards based on this SoC. You can safely enable multiple clock
+ drivers. The one(s) matching the device tree will be used.
diff --git a/drivers/clk/zte/Makefile b/drivers/clk/zte/Makefile
index 27db07293165..2c073512e919 100644
--- a/drivers/clk/zte/Makefile
+++ b/drivers/clk/zte/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0-only
obj-$(CONFIG_COMMON_CLK_ZTE) += clk-zte.o
+obj-$(CONFIG_CLK_ZTE_ZX297520V3) += clk-zx297520v3.o
clk-zte-y += clk-zx.o pll-zx.o clk-regmap.o
diff --git a/drivers/clk/zte/clk-zx297520v3.c b/drivers/clk/zte/clk-zx297520v3.c
new file mode 100644
index 000000000000..50263bca6e08
--- /dev/null
+++ b/drivers/clk/zte/clk-zx297520v3.c
@@ -0,0 +1,431 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2026 Stefan Dösinger
+ */
+#include <dt-bindings/clock/zte,zx297520v3-clk.h>
+#include <linux/platform_device.h>
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+
+#include "clk-zx.h"
+
+MODULE_IMPORT_NS("ZTE_CLK");
+
+/* Used for gates where we don't know the parent input(s). Assume general bus clock. */
+static const char * const clk_unknown[] = {
+ "osc26m",
+};
+
+/* Used for gates where we know it is using the 26 mhz main clock. */
+static const char * const clk_main[] = {
+ "osc26m",
+};
+
+static const char * const zx297529v3_top_inputs[] = {
+ "osc26m",
+ "osc32k"
+};
+
+/* Top and matrix clocks are chaotic - I haven't found a consistent pattern behind their register
+ * and bit locations. Generally there are two gates (pclk, wclk), one mux, two resets and sometimes
+ * one divider, but exceptions apply. For some devices there is only a reset and some general
+ * (parent) clocks need setup. This structure plus macro handles the somewhat regular parts.
+ *
+ * There are some patterns that can be observed.
+ * mux 0x3c, div 0x48, gate 0x54
+ * mux 0x40, div 0x4c, gate 0x5c
+ * mux 0x44, div 0x50, gate 0x60
+ *
+ * For a 0 - 0xc - 0x18 pattern. Muxes from 0x3c to 0x44, dividers from 0x48 to 0x50, gates 0x54 to
+ * 0x60. The pattern is broken for timer t17 though.
+ *
+ * Gates have 4 bits per clock - bit 0 for wclk, bit 1 for pclk, bit 2 for something the ZTE kernel
+ * calls "gate" (the bits we use here are called "en"), which I don't know what it does, and bit 3
+ * seems unused. E.g. offset 0x54 accepts all bits in 0xF77F7F7F - suggesting RTC, I2C0 have an
+ * extra gate bit.
+ *
+ * The default mpll settings multiply the 26 MHz reference clock times 24. A mux selection of 26 MHz
+ * could mean using the 26 MHz oscillator directly, or passing it through the PLL and divide by 24.
+ *
+ * If a UART is set to mpl_d6 (default 104 MHz), changing the mpll multipliers does affect UART
+ * timing as it should. This does not happen when the UART is set to 26 MHz input or timers that
+ * read 26 MHz input. This suggests 26 MHz clocks use the reference clock directly.
+ */
+
+/* AHB: The clock mux works and impact can be tested e.g. with iperf speed testing of the USB
+ * network connection. Values 2 and 3 give the same speed.
+ */
+static const char * const ahb_sel[] = {
+ "osc26m",
+ "mpll_d6", /* 104 mhz */
+ "mpll_d8", /* 78 mhz */
+ "mpll_d8", /* 78 mhz */
+};
+
+static const char * const timer_top_sel[] = {
+ "osc32k",
+ "osc26m",
+};
+
+static const char * const uart_top_sel[] = {
+ "osc26m",
+ "mpll_d6", /* 104 mhz */
+};
+
+/* The Cortex M0 coprocessor. It is responsible for booting the board and runs some power management
+ * helper code on the stock firmware, but isn't critical. We can run custom code on it but currently
+ * do not. These bits control the speed and the values are mentioned in ZTE's uboot. It isn't clear
+ * to me if this is directly responsible for the m0 clock, or if it is the input to another clock.
+ * Most likely it is the latter - setting it to osc32k slows down GPIO reads done on the Cortex A53
+ * a lot, although the speed of the A53 and DRAM access remains unaffected.
+ *
+ * I also haven't found a gate that shuts the m0 off and allows restarting. There don't seem to be
+ * resets either.
+ */
+static const char * const m0_sel[] = {
+ "osc26m",
+ "mpll_d6", /* 104 mhz */
+ "mpll_d8", /* 78 mhz */
+ "osc32k", /* Yes, tested. It is SLLLLOOOOOWWW. */
+};
+
+/* Clk_out0/1/2/32k: These clocks are exposed on GPIOs 15, 16, 17 and 18 respectively. They are used
+ * in ZTE's camera and sound code, by directly poking into the clock registers from the device
+ * drivers. Until the respective devices are supported they can safely be switched off.
+ *
+ * For clk_out1 ZTE's camera code says the following:
+ *
+ * 0 -> 20 MHz
+ * 1 -> 40 MHz
+ * 2 -> 13 MHz
+ * 3 -> 26 MHz
+ *
+ * 0 and 1 read from upll. I confirmed their rates (upll_d24 and upll_d12) by setting upll to a very
+ * low frequency and sampling the clock by GPIO reads. The outputs of 2 and 3 are way too high to
+ * test that way. Both are not reading from any PLL. I am fairly sure that 3 is just direct osc26m
+ * because it perfectly matches what out2 is showing in its 26 MHz setting. Setting 2 is an enigma.
+ * It is not from any PLL (disable postdiv_out on all of them and the clock will keep oscillating).
+ *
+ * Probably the best way us to model this as a mux (bit 7) and divider (bit 6), but since this is
+ * not a plain val+1 divider like the rest of the divs I am leaving the divider out until an actual
+ * hardware user is found. It would need support for divider tables or flags in the regmap div
+ * clocks.
+ *
+ * Clk_out2 is similar, but it has only one control bit in top 0x34 bit 8. Neither setting selects
+ * a PLL output. When setting *0x34 = 0x080, clk_out1 and clk_out2 are in lockstep, presumably
+ * running at 13 MHz (clk_out1 mux select 26m, both have their divider set to 2). 0x1c0 also runs in
+ * lockstep (clk_out1 select 26m, both div 1).
+ *
+ * clk_out0 has a mux in bit 5. Value 0 most likely selects osc26m. I am not entirely sure about
+ * value 1 (which is the default), but the m0 mux has an impact on it. It looks like a debug pin
+ * that exposes some core clock.
+ */
+
+static const char * const out0_sel[] = {
+ "osc26m",
+ "m0_wclk",
+};
+
+static const char * const out1_sel[] = {
+ "upll_d12", /* 40 MHz */
+ "osc26m",
+};
+
+/* Clk_o is similar to clk_out*, providing a clock on GPIO 20, presumably for driving a (R)MII phy.
+ * The 50 MHz value is documented in a stray comment in ZTE's GMAC driver. I tested it similarly to
+ * the above pins. Mux setting 0 gives half the count as setting 1 and setting 1 gives gpll divided
+ * by 4 - matching the 50 MHz suggested by the ZTE comment at the default gpll settings. Gating gpll
+ * stops the clock for values 0 and 1.
+ *
+ * Settings 2 and 3 are possible, but seem to return garbage. It is generally pulsing up and down,
+ * except if both gpll and upll are stopped. I suspect it just reads random electrical fluctuation
+ * from other places in the board. Yes, I had a pull-down enabled when testing this.
+ *
+ * This could also be a case of mux + inverse div, but since the settings we might possibly need are
+ * standard gpll outputs just model it as a mux.
+ *
+ * I am not aware of any board that uses this though. The Ethernet equipped ones I have all run the
+ * phy with its own oscillator.
+ */
+static const char * const rmii_sel[] = {
+ "gpll_d8", /* 25 MHz */
+ "gpll_d4", /* 50 MHz */
+};
+
+static const unsigned int mpll_postdivs[] = {1, 2, 3, 4, 5, 6, 8, 12, 16, 26};
+static const unsigned int pll_postdivs[] = {1, 2, 3, 4, 5, 6, 8, 12, 16};
+static const unsigned int unknownpll_postdivs[] = {2};
+
+static const struct zx_pll_desc zx297520v3_plls[] = {
+ /* Default setting: 0x48040c11. 624/312/156. Only a single possible parent. This is the
+ * PLL for pretty much everything, including CPU, RAM and USB.
+ *
+ * Changing this PLL makes it possible to overclock the CPU or do more fine grained
+ * underclocking than the CPU's mux allows. It does run into two problems though: The USB
+ * device uses this PLL's output directly and is *very* sensitive to differences. DRAM
+ * is also fed by this clock and needs to be re-trained on larger changes, which needs to
+ * be done by the stage 1 boot loader.
+ */
+ {
+ .id = ZX297520V3_MPLL,
+ .name = "mpll",
+ .parents = clk_main,
+ .num_parents = ARRAY_SIZE(clk_main),
+ .rate = 0,
+ .postdivs = mpll_postdivs,
+ .num_postdivs = ARRAY_SIZE(mpll_postdivs),
+ .reg = 0x8
+ },
+
+ /* ZTE's code calls this PLL "upll". The only possible consumer I found is clk_out1, which
+ * outputs this clock on GPIO 16. The device that consumes this is an SPI camera, which I
+ * haven't seen in any device so far.
+ *
+ * Long story short, shut it off.
+ */
+ {
+ .id = ZX297520V3_UPLL,
+ .name = "upll",
+ .parents = clk_main,
+ .num_parents = ARRAY_SIZE(clk_main),
+ .rate = 0,
+ .postdivs = pll_postdivs,
+ .num_postdivs = ARRAY_SIZE(pll_postdivs),
+ .reg = 0x10,
+ },
+
+ /* Default value 0x4834902d. Feeds dpll. 46.08 MHz. Bit 25 can be set, so two parents are
+ * possible. It looks like both values select the 26 MHz oscillator though.
+ */
+ {
+ .id = 0,
+ .name = "unknownpll",
+ .parents = clk_main,
+ .num_parents = ARRAY_SIZE(clk_main),
+ .rate = 0,
+ .postdivs = unknownpll_postdivs,
+ .num_postdivs = ARRAY_SIZE(unknownpll_postdivs),
+ .reg = 0x100,
+ },
+
+ /* The documentation says 491.52 MHz and measurement with the LSP TDM device supports this.
+ * The default value is 0x480c2011, but not all boot loaders set it up. To get to 491.52
+ * with these settings it needs a 23.04 MHz reference clock, which matches unknownpll_d2.
+ * If unknownpll is disabled, dpll loses its lock. We set the frequency on this PLL if we
+ * find it is not enabled by the boot loader.
+ *
+ * The proprietary LTE driver or coproc enables and disables it. TDM and I2S can use it.
+ *
+ * It accepts parent values 0, 1, 2 and 3. Parent 0 is unknownpll_d2. The others look like
+ * osc26m. With a parent != 0 dpll never loses its lock even when all other PLLs are off
+ * and the TDM counter register increases at a rate consistent with a 26.0/23.04 clock
+ * increase.
+ */
+ {
+ .id = ZX297520V3_DPLL,
+ .name = "dpll",
+ .parents = clk_main,
+ .num_parents = ARRAY_SIZE(clk_main),
+ .rate = 491520000,
+ .postdivs = pll_postdivs,
+ .num_postdivs = ARRAY_SIZE(pll_postdivs),
+ .reg = 0x18,
+ },
+
+ /* "g" is either for "general" or "gigahertz". The VCO runs at 1GHz. Output clocks are 200,
+ * 100, 50, 25, ... MHz. It is used optionally by SDIO and QSPI and can drive a GPIO clock
+ * output for RMII, so it doesn't seem very general.
+ */
+ {
+ .id = ZX297520V3_GPLL,
+ .name = "gpll",
+ .parents = clk_main,
+ .num_parents = ARRAY_SIZE(clk_main),
+ .rate = 0,
+ .postdivs = pll_postdivs,
+ .num_postdivs = ARRAY_SIZE(pll_postdivs),
+ .reg = 0x110,
+ },
+};
+
+#define MUX(_id, _name, _parents, _reg, _shift, _size) { \
+ _id, _name, _parents, ARRAY_SIZE(_parents), _reg, _shift, _size}
+
+#define DIV(_id, _name, _parent, _reg, _shift, _size) { _id, _name, _parent, _reg, _shift, _size }
+
+#define GATE(_id, _name, _parent, _reg, _shift, _flags) { \
+ .id = _id, \
+ .name = _name, \
+ .parent = _parent, \
+ .flags = _flags, \
+ .reg = _reg, \
+ .shift = _shift, \
+}
+
+static const struct zx_mux_desc zx297520v3_top_muxes[] = {
+ MUX(ZX297520V3_M0_WCLK, "m0_wclk", m0_sel, 0x38, 0, 2),
+ MUX(0, "ahb_mux", ahb_sel, 0x3c, 4, 2),
+ MUX(0, "timer_t08_mux", timer_top_sel, 0x40, 1, 1),
+ MUX(0, "timer_t09_mux", timer_top_sel, 0x40, 0, 1),
+ MUX(0, "timer_t12_mux", timer_top_sel, 0x3c, 0, 1),
+ MUX(0, "timer_t13_mux", timer_top_sel, 0x44, 0, 1),
+ MUX(0, "timer_t14_mux", timer_top_sel, 0x44, 1, 1),
+ MUX(0, "timer_t15_mux", timer_top_sel, 0x3c, 3, 1),
+ MUX(0, "timer_t16_mux", timer_top_sel, 0x44, 2, 1),
+ MUX(0, "timer_t17_mux", timer_top_sel, 0x120, 0, 1),
+ MUX(0, "wdt_t18_mux", timer_top_sel, 0x3c, 6, 1),
+ MUX(0, "i2c0_mux", uart_top_sel, 0x3c, 1, 1),
+ MUX(0, "uart0_mux", uart_top_sel, 0x40, 2, 1),
+ MUX(0, "out0_mux", out0_sel, 0x34, 5, 1),
+ MUX(0, "out1_mux", out1_sel, 0x34, 7, 1),
+ MUX(0, "rmiiphy_mux", rmii_sel, 0x11c, 0, 2),
+};
+
+static const struct zx_div_desc zx297520v3_top_dividers[] = {
+ DIV(0, "timer_t08_div", "timer_t08_mux", 0x4c, 8, 4),
+ DIV(0, "timer_t09_div", "timer_t09_mux", 0x4c, 0, 4),
+ DIV(0, "timer_t12_div", "timer_t12_mux", 0x48, 0, 4),
+ DIV(0, "timer_t13_div", "timer_t13_mux", 0x50, 0, 4),
+ DIV(0, "timer_t14_div", "timer_t14_mux", 0x50, 4, 4),
+ DIV(0, "timer_t15_div", "timer_t15_mux", 0x48, 4, 4),
+ DIV(0, "timer_t16_div", "timer_t16_mux", 0x50, 8, 4),
+ DIV(0, "timer_t17_div", "timer_t17_mux", 0x124, 0, 4),
+ DIV(0, "wdt_t18_div", "wdt_t18_mux", 0x48, 8, 4),
+ DIV(0, "usim1_div", clk_main[0], 0x48, 12, 1),
+};
+
+static const struct zx_gate_desc zx297520v3_top_gates[] = {
+ /* Turning off this clock crashes the device. */
+ GATE(ZX297520V3_AHB_WCLK, "ahb_wclk", "ahb_mux", 0x54, 12,
+ CLK_IS_CRITICAL),
+ GATE(ZX297520V3_AHB_PCLK, "ahb_pclk", clk_main[0], 0x54, 13,
+ CLK_IS_CRITICAL),
+
+ /* SRAM1 and 2 clocks. Leave them on for now, as turning them off carelessly hangs the M0 */
+ GATE(ZX297520V3_SRAM1_PCLK, "sram1_pclk", clk_main[0], 0x54, 18,
+ CLK_IS_CRITICAL),
+ GATE(ZX297520V3_SRAM2_PCLK, "sram2_pclk", clk_main[0], 0x54, 16,
+ CLK_IS_CRITICAL),
+
+ /* Pinmux (AON, TOP, IOCFG but not PDCFG). Critical as well until we have a driver that
+ * consumes it. I don't think we'll realistically shut this off ever.
+ *
+ * Setting either bit 0 or 1 in register 0x58 makes the device work.
+ */
+ GATE(ZX297520V3_PMM_WCLK, "pmm_wclk", clk_main[0], 0x58, 0,
+ CLK_IS_CRITICAL),
+ GATE(ZX297520V3_PMM_PCLK, "pmm_pclk", clk_main[0], 0x58, 1,
+ CLK_IS_CRITICAL),
+
+ /* Timers. We don't use any of them, just shut them off. The timers are named and sorted
+ * by the IO address of the main timer controls. Some of the controls are documented in
+ * ZTE's kernel, the others I found by trial and error.
+ *
+ * Timer T17 is used by the ZSP firmware. The rproc driver will enable it as needed.
+ */
+ GATE(ZX297520V3_TIMER_T08_WCLK, "timer_t08_wclk", "timer_t08_div", 0x5c, 8, 0),
+ GATE(ZX297520V3_TIMER_T08_PCLK, "timer_t08_pclk", clk_main[0], 0x5c, 9, 0),
+ GATE(ZX297520V3_TIMER_T09_WCLK, "timer_t09_wclk", "timer_t09_div", 0x5c, 4, 0),
+ GATE(ZX297520V3_TIMER_T09_PCLK, "timer_t09_pclk", clk_main[0], 0x5c, 5, 0),
+ GATE(ZX297520V3_TIMER_T12_WCLK, "timer_t12_wclk", "timer_t12_div", 0x54, 4, 0),
+ GATE(ZX297520V3_TIMER_T12_PCLK, "timer_t12_pclk", clk_main[0], 0x54, 5, 0),
+ GATE(ZX297520V3_TIMER_T13_WCLK, "timer_t13_wclk", "timer_t13_div", 0x60, 0, 0),
+ GATE(ZX297520V3_TIMER_T13_PCLK, "timer_t13_pclk", clk_main[0], 0x60, 1, 0),
+ GATE(ZX297520V3_TIMER_T14_WCLK, "timer_t14_wclk", "timer_t14_div", 0x60, 4, 0),
+ GATE(ZX297520V3_TIMER_T14_PCLK, "timer_t14_pclk", clk_main[0], 0x60, 5, 0),
+ GATE(ZX297520V3_TIMER_T15_WCLK, "timer_t15_wclk", "timer_t15_div", 0x54, 20, 0),
+ GATE(ZX297520V3_TIMER_T15_PCLK, "timer_t15_pclk", clk_main[0], 0x54, 21, 0),
+ GATE(ZX297520V3_TIMER_T16_WCLK, "timer_t16_wclk", "timer_t16_div", 0x60, 8, 0),
+ GATE(ZX297520V3_TIMER_T16_PCLK, "timer_t16_pclk", clk_main[0], 0x60, 9, 0),
+ GATE(ZX297520V3_TIMER_T17_WCLK, "timer_t17_wclk", "timer_t17_div", 0x128, 0, 0),
+ GATE(ZX297520V3_TIMER_T17_PCLK, "timer_t17_pclk", clk_main[0], 0x128, 1, 0),
+ /* This watchdog is set up by the bootloader and in normal operation the m0 firmware will
+ * feed the dog. The m0 firmware in turn wants to be fed in its own way. Since we normally
+ * don't run any m0 firmware we shut it off by default and expose it to userspace via the
+ * watchdog driver.
+ */
+ GATE(ZX297520V3_WDT_T18_WCLK, "wdt_t18_wclk", "wdt_t18_div", 0x54, 24, 0),
+ GATE(ZX297520V3_WDT_T18_PCLK, "wdt_t18_pclk", clk_main[0], 0x54, 25, 0),
+
+ GATE(ZX297520V3_I2C0_WCLK, "i2c0_wclk", "i2c0_mux", 0x54, 8, 0),
+ GATE(ZX297520V3_I2C0_PCLK, "i2c0_pclk", clk_main[0], 0x54, 9, 0),
+ GATE(ZX297520V3_UART0_WCLK, "uart0_wclk", "uart0_mux", 0x5c, 12, 0),
+ GATE(ZX297520V3_UART0_PCLK, "uart0_pclk", clk_main[0], 0x5c, 13, 0),
+
+ /* ZTE says the USB input is a 24 MHz clock based on mpll. Testing shows that Upll is not
+ * involved. The USB register space can be accessed with ahb_pclk gated, but not with
+ * ahb_wclk gated. ZTE also lists ahb_wclk as parent for the second clock.
+ */
+ GATE(ZX297520V3_USB_WCLK, "usb_wclk", "mpll_d26", 0x6c, 3, 0),
+ GATE(ZX297520V3_USB_PCLK, "usb_pclk", "ahb_wclk", 0x6c, 4, 0),
+ /* The HSIC hardware is listed in ZTE's code with a physical address of 0x01600000. These
+ * bits are part of the ones that control it.
+ */
+ GATE(ZX297520V3_HSIC_WCLK, "hsic_wclk", "mpll_d26", 0x6c, 1, 0),
+ GATE(ZX297520V3_HSIC_PCLK, "hsic_pclk", "ahb_wclk", 0x6c, 2, 0),
+
+ /* How does this RTC work? I don't know, the ZTE kernel does not talk to it. The actual RTC
+ * is on the I2C connected PMIC.
+ */
+ GATE(ZX297520V3_RTC_WCLK, "rtc_wclk", clk_unknown[0], 0x54, 0, 0),
+ GATE(ZX297520V3_RTC_PCLK, "rtc_pclk", clk_main[0], 0x54, 1, 0),
+
+ GATE(ZX297520V3_USIM1_WCLK, "usim1_wclk", "usim1_div", 0x54, 28, 0),
+ GATE(ZX297520V3_USIM1_PCLK, "usim1_pclk", clk_main[0], 0x54, 29, 0),
+
+ /* LTE: gate only as far as I can see. I looked for resets and did not find any. There may
+ * be mux/div, but without understanding the behavior of this hardware it is impossible to
+ * tell. They are sorted by physical MMIO address of the devices, which happens to be the
+ * inverse order of the bits.
+ *
+ * I don't know what "LPM", "TD" and "W" mean. I copied them from ZTE's names.
+ */
+ GATE(ZX297520V3_LPM_GSM_WCLK, "lpm_gsm_wclk", clk_unknown[0], 0x58, 10, 0),
+ GATE(ZX297520V3_LPM_GSM_PCLK, "lpm_gsm_pclk", clk_unknown[0], 0x58, 11, 0),
+ GATE(ZX297520V3_LPM_LTE_WCLK, "lpm_lte_wclk", clk_unknown[0], 0x58, 8, 0),
+ GATE(ZX297520V3_LPM_LTE_PCLK, "lpm_lte_pclk", clk_unknown[0], 0x58, 9, 0),
+ GATE(ZX297520V3_LPM_TD_WCLK, "lpm_td_wclk", clk_unknown[0], 0x58, 6, 0),
+ GATE(ZX297520V3_LPM_TD_PCLK, "lpm_td_pclk", clk_unknown[0], 0x58, 7, 0),
+ GATE(ZX297520V3_LPM_W_WCLK, "lpm_w_wclk", clk_unknown[0], 0x58, 4, 0),
+ GATE(ZX297520V3_LPM_W_PCLK, "lpm_w_pclk", clk_unknown[0], 0x58, 5, 0),
+
+ GATE(ZX297520V3_OUT0_WCLK, "out0_wclk", "out0_mux", 0x34, 0, 0),
+ GATE(ZX297520V3_OUT1_WCLK, "out1_wclk", "out1_mux", 0x90, 2, 0),
+ GATE(ZX297520V3_OUT2_WCLK, "out2_wclk", clk_main[0], 0x94, 2, 0),
+ GATE(ZX297520V3_OUT32K_WCLK, "out32k_wclk", "osc32k", 0x34, 1, 0),
+ GATE(ZX297520V3_RMIIPHY_WCLK, "rmiiphy_wclk", "rmiiphy_mux", 0x11c, 2, 0),
+};
+
+static const struct zx_clk_data zx297520v3_topclk_data = {
+ .inputs = zx297529v3_top_inputs,
+ .num_inputs = ARRAY_SIZE(zx297529v3_top_inputs),
+ .plls = zx297520v3_plls,
+ .num_plls = ARRAY_SIZE(zx297520v3_plls),
+ .muxes = zx297520v3_top_muxes,
+ .num_muxes = ARRAY_SIZE(zx297520v3_top_muxes),
+ .divs = zx297520v3_top_dividers,
+ .num_divs = ARRAY_SIZE(zx297520v3_top_dividers),
+ .gates = zx297520v3_top_gates,
+ .num_gates = ARRAY_SIZE(zx297520v3_top_gates),
+ .reset_auxdev_name = "zx297520v3_toprst"
+};
+
+static const struct of_device_id of_match_zx297520v3[] = {
+ { .compatible = "zte,zx297520v3-topclk", .data = &zx297520v3_topclk_data },
+ { }
+};
+MODULE_DEVICE_TABLE(of, of_match_zx297520v3);
+
+static struct platform_driver clk_zx297520v3 = {
+ .probe = zx_clk_probe,
+ .driver = {
+ .name = "clk-zx297520v3",
+ .of_match_table = of_match_zx297520v3,
+ },
+};
+
+module_platform_driver(clk_zx297520v3);
+
+MODULE_AUTHOR("Stefan Dösinger <stefandoesinger@gmail.com>");
+MODULE_DESCRIPTION("ZTE zx297520v3 clock driver");
+MODULE_LICENSE("GPL");
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 08/12] clk: zte: Introduce a driver for zx297520v3 matrix clocks
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
This clock controller controls high speed devices: CPU, DMA, RAM, SDIO,
Ethernet. The only non-clock, non-reset registers I have spotted here
are hardware spinlocks.
I put the entire set of PLL generated frequencies as consumed clocks in
the binding. Due to lack of a data sheet I can't rule out that the any
of the PLL subdivions are used.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
drivers/clk/zte/clk-zx297520v3.c | 172 +++++++++++++++++++++++++++++++++++++++
1 file changed, 172 insertions(+)
diff --git a/drivers/clk/zte/clk-zx297520v3.c b/drivers/clk/zte/clk-zx297520v3.c
index 50263bca6e08..d90aadf18026 100644
--- a/drivers/clk/zte/clk-zx297520v3.c
+++ b/drivers/clk/zte/clk-zx297520v3.c
@@ -410,8 +410,180 @@ static const struct zx_clk_data zx297520v3_topclk_data = {
.reset_auxdev_name = "zx297520v3_toprst"
};
+static const char * const cpu_sel[] = {
+ "osc26m",
+ "mpll", /* 624 MHz */
+ "mpll_d2", /* 312 MHz */
+ "mpll_d4", /* 156 MHz */
+};
+
+static const char * const sd0_sel[] = {
+ "osc26m",
+ "mpll_d4", /* 156 MHz */
+ "gpll_d2", /* 100 MHz */
+ "mpll_d8", /* 78 MHz */
+ "gpll_d4", /* 50 MHz */
+ "gpll_d8", /* 25 MHz */
+};
+
+static const char * const sd1_sel[] = {
+ "osc26m",
+ "gpll_d2", /* 100 MHz */
+ "mpll_d8", /* 78 MHz */
+ "gpll_d4", /* 50 MHz */
+ "mpll_d16", /* 39 MHz */
+ "gpll_d8", /* 25 MHz */
+};
+
+static const char * const nand_sel[] = {
+ "mpll_d4", /* 156 MHz */
+ "osc26m",
+};
+
+static const char * const edcp_sel[] = {
+ "osc26m",
+ "mpll_d4", /* 156 MHz */
+ "mpll_d5", /* 124.8 MHz */
+ "mpll_d6", /* 104 MHz */
+};
+
+static const char * const tdm_sel[] = {
+ "osc26m",
+ "dpll_d4", /* 122.88 MHz */
+ "mpll_d6", /* 104 MHz */
+};
+
+static const struct zx_mux_desc zx297520v3_matrix_muxes[] = {
+ MUX(0, "cpu_mux", cpu_sel, 0x20, 0, 2),
+ MUX(0, "sd0_mux", sd0_sel, 0x50, 4, 3),
+ MUX(0, "sd1_mux", sd1_sel, 0x50, 8, 3),
+ MUX(0, "nand_mux", nand_sel, 0x50, 12, 2),
+ MUX(0, "edcp_mux", edcp_sel, 0x50, 16, 2),
+ MUX(0, "tdm_mux", tdm_sel, 0x50, 24, 2),
+};
+
+static const struct zx_gate_desc zx297520v3_matrix_gates[] = {
+ /* Both 0x24 and 0x28 bits 1 and 2 stop the CPU. There is also a bit in topclk+0x138, which
+ * ZTE's uboot calls "A53 reset", which also stops the CPU. I can't really tell the
+ * difference between matrix+28 and top+138. The clock (maxtrix+0x24) can be disabled and
+ * enabled from the Cortex M0 and it will nicely stop and restart the A53, retaining all
+ * state.
+ *
+ * 0x50, bits 0-3 have the DDR clock. A lot of DDR gates and resets are in 0x100.
+ */
+ GATE(ZX297520V3_CPU_WCLK, "cpu_wclk", "cpu_mux", 0x24, 1,
+ CLK_IS_CRITICAL),
+ GATE(ZX297520V3_CPU_PCLK, "cpu_pclk", clk_main[0], 0x24, 2,
+ CLK_IS_CRITICAL),
+
+ /* ZSP aka LTE DSP clock. I think there is a mux at matrix+0x30, but I have no idea
+ * about the frequencies it selects.
+ */
+ GATE(ZX297520V3_ZSP_WCLK, "zsp_wclk", clk_unknown[0], 0x3c, 0, 0),
+
+ GATE(ZX297520V3_SD0_WCLK, "sd0_wclk", "sd0_mux", 0x54, 12, 0),
+ GATE(ZX297520V3_SD0_PCLK, "sd0_pclk", clk_main[0], 0x54, 13, 0),
+ GATE(ZX297520V3_SD0_CDET, "sd0_cdet", "osc32k", 0x54, 14, 0),
+ GATE(ZX297520V3_SD1_WCLK, "sd1_wclk", "sd1_mux", 0x54, 4, 0),
+ GATE(ZX297520V3_SD1_PCLK, "sd1_pclk", clk_main[0], 0x54, 5, 0),
+ /* I don't know how the cdet clock works. Card detection in the way the dwc,mmc driver uses
+ * it appears broken no matter this clock's setting.
+ */
+ GATE(ZX297520V3_SD1_CDET, "sd1_cdet", "osc32k", 0x54, 6, 0),
+
+ /* This is some "denali" NAND, not the qspi connected one */
+ GATE(ZX297520V3_NAND_WCLK, "nand_wclk", "nand_mux", 0x54, 20, 0),
+ GATE(ZX297520V3_NAND_PCLK, "nand_pclk", clk_main[0], 0x54, 21, 0),
+ GATE(ZX297520V3_SSC_WCLK, "ssc_wclk", clk_unknown[0], 0x84, 1, 0),
+ GATE(ZX297520V3_SSC_PCLK, "ssc_pclk", clk_main[0], 0x84, 2, 0),
+
+ /* Yes, WCLK bit > PCLK bit for EDCP */
+ GATE(ZX297520V3_EDCP_WCLK, "edcp_wclk", "edcp_mux", 0x64, 2, 0),
+ GATE(ZX297520V3_EDCP_PCLK, "edcp_pclk", clk_main[0], 0x64, 1, 0),
+
+ /* There are a lot more VOU related controls in these registers, but turning off the main
+ * clock seems to shut off the entire VOU MMIO range.
+ */
+ GATE(ZX297520V3_VOU_WCLK, "vou_wclk", clk_unknown[0], 0x168, 0, 0),
+ GATE(ZX297520V3_VOU_PCLK, "vou_pclk", clk_main[0], 0x168, 1, 0),
+
+ /* PDCFG. Like PMM, either clock bit will allow the device to function. */
+ GATE(ZX297520V3_PDCFG_WCLK, "pdcfg_wclk", clk_unknown[0], 0x88, 0,
+ CLK_IS_CRITICAL),
+ GATE(ZX297520V3_PDCFG_PCLK, "pdcfg_pclk", clk_main[0], 0x88, 1,
+ CLK_IS_CRITICAL),
+
+ /* ZTE's driver has a statemt to the effect of *(top->base+0x11c) = 5, with a comment
+ * suggesting that this sets a 50 mhz clock. The clock code itself lists gmac clocks in
+ * matrix+110 and lists the parents of these clock as 50mhz gpll output, but the GMAC
+ * driver never enables the clocks. It turns out ZTE's code is highly misleading.
+ *
+ * The GMAC's work clock is definitly not any gpll output because it keeps working fine with
+ * gpll disabled. The MDIO speed is mostly unaffected by mpll speed changes, so it is most
+ * likely not fed by mpll either. All other PLLs can be disabled without breaking GMAC, so
+ * osc26m is the only possible remaining parent.
+ *
+ * The GMAC Gates are left enabled by the boot loader and are required for the GMAC to work.
+ *
+ * As for the 50 MHz comment: See rmiiphy_wclk.
+ */
+ GATE(ZX297520V3_GMAC_WCLK, "gmac_wclk", clk_main[0], 0x110, 0, 0),
+ GATE(ZX297520V3_GMAC_PCLK, "gmac_pclk", clk_main[0], 0x110, 1, 0),
+ GATE(ZX297520V3_GMAC_AHB, "gmac_ahb", "AHB_wclk", 0x110, 2, 0),
+
+ GATE(ZX297520V3_MBOX_PCLK, "mbox_pclk", clk_main[0], 0x88, 2, 0),
+ GATE(ZX297520V3_DMA_PCLK, "dma_pclk", clk_main[0], 0x94, 3, 0),
+
+ /* LSP uplink clocks. The PCLK is fairly obvious (disabling it shuts off the entire LSP
+ * register area). The WCLK speeds were deduced by setting timers and qspi muxes to a
+ * specific speed and seeing which bit in matrix+0x7c needs to be enabled for the device
+ * to work.
+ *
+ * Due to the timers I am certain about the 26mhz and 32khz clocks. I cannot directly
+ * observe the qspi mux frequency, so the clock rates depend on ZTE's qspi mux selection
+ * being correct.
+ *
+ * Two additional bits are specific to sound components - the mux for the LSP's TDM IP is
+ * in matrixclk and gets passed down. I2S has a mux in LSP, which can select the dpll_d4
+ * clock.
+ */
+ GATE(ZX297520V3_LSP_MPLL_D5_WCLK, "lsp_mpll_d5", "mpll_d5", 0x7c, 0, 0),
+ GATE(ZX297520V3_LSP_MPLL_D4_WCLK, "lsp_mpll_d4", "mpll_d4", 0x7c, 1, 0),
+ GATE(ZX297520V3_LSP_MPLL_D6_WCLK, "lsp_mpll_d6", "mpll_d6", 0x7c, 2, 0),
+ GATE(ZX297520V3_LSP_MPLL_D8_WCLK, "lsp_mpll_d8", "mpll_d8", 0x7c, 3, 0),
+ GATE(ZX297520V3_LSP_MPLL_D12_WCLK, "lsp_mpll_d12", "mpll_d12", 0x7c, 4, 0),
+ GATE(ZX297520V3_LSP_OSC26M_WCLK, "lsp_osc26m", clk_main[0], 0x7c, 5, 0),
+ GATE(ZX297520V3_LSP_OSC32K_WCLK, "lsp_osc32k", "osc32k", 0x7c, 6, 0),
+ GATE(ZX297520V3_LSP_PCLK, "lsp_pclk", clk_main[0], 0x7c, 7, 0),
+ GATE(ZX297520V3_LSP_TDM_WCLK, "lsp_tdm_wclk", "tdm_mux", 0x7c, 8, 0),
+ GATE(ZX297520V3_LSP_DPLL_D4_WCLK, "lsp_dpll_d4", "dpll_d4", 0x7c, 9, 0),
+};
+
+static const char * const zx297529v3_matrix_inputs[] = {
+ "osc26m", "osc32k",
+ "mpll", "mpll_d2", "mpll_d3", "mpll_d4", "mpll_d5", "mpll_d6", "mpll_d8", "mpll_d12",
+ "mpll_d16", "mpll_d26",
+ "upll", "upll_d2", "upll_d3", "upll_d4", "upll_d5", "upll_d6", "upll_d8", "upll_d12",
+ "upll_d16",
+ "dpll", "dpll_d2", "dpll_d3", "dpll_d4", "dpll_d5", "dpll_d6", "dpll_d8", "dpll_d12",
+ "dpll_d16",
+ "gpll", "gpll_d2", "gpll_d3", "gpll_d4", "gpll_d5", "gpll_d6", "gpll_d8", "gpll_d12",
+ "gpll_d16",
+};
+
+static const struct zx_clk_data zx297520v3_matrixclk_data = {
+ .inputs = zx297529v3_matrix_inputs,
+ .num_inputs = ARRAY_SIZE(zx297529v3_matrix_inputs),
+ .muxes = zx297520v3_matrix_muxes,
+ .num_muxes = ARRAY_SIZE(zx297520v3_matrix_muxes),
+ .gates = zx297520v3_matrix_gates,
+ .num_gates = ARRAY_SIZE(zx297520v3_matrix_gates),
+ .reset_auxdev_name = "zx297520v3_matrixrst"
+};
+
static const struct of_device_id of_match_zx297520v3[] = {
{ .compatible = "zte,zx297520v3-topclk", .data = &zx297520v3_topclk_data },
+ { .compatible = "zte,zx297520v3-matrixclk", .data = &zx297520v3_matrixclk_data },
{ }
};
MODULE_DEVICE_TABLE(of, of_match_zx297520v3);
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 09/12] clk: zte: Introduce a driver for zx297520v3 LSP clocks
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
"LSP" is ZTE's term for this part of the SoC, I suspect it stands for
"low speed peripherals". The main UART is here, together with the flash
controller and more surplus proprietary timers.
It also has two more I2C controllers that supposedly connect to a
battery charger, SPI for displays and I2S for analog telephones. The
boards I have don't have any of these components though.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
drivers/clk/zte/clk-zx297520v3.c | 192 +++++++++++++++++++++++++++++++++++++++
1 file changed, 192 insertions(+)
diff --git a/drivers/clk/zte/clk-zx297520v3.c b/drivers/clk/zte/clk-zx297520v3.c
index d90aadf18026..26b05f2bf97a 100644
--- a/drivers/clk/zte/clk-zx297520v3.c
+++ b/drivers/clk/zte/clk-zx297520v3.c
@@ -581,9 +581,201 @@ static const struct zx_clk_data zx297520v3_matrixclk_data = {
.reset_auxdev_name = "zx297520v3_matrixrst"
};
+/* LSP clock entries have a common pattern: Bit 0 for WCLK, Bit 1 for PCLK. Bit 4 (and sometimes
+ * more) for WCLK mux.
+ *
+ * Bit 8 and 9 are reset bits. I don't know the difference between the two, but they both need to be
+ * set to deassert the reset.
+ *
+ * Bits 15:12 can be a divisor, but not all clocks have it. Some clocks have a divisor in 19:16.
+ *
+ * The ID given in this table is the first register in the device's MMIO space. ZTE's drivers
+ * usually call this a version register, but it looks more like a device identifier.
+ *
+ * It looks like the registers map to devices like this:
+ *
+ * Timer reg function div dev offset(lsp + xxxx) ID
+ * 0x0: Read-only, probably device identifier 0x00752100
+ * 0x4: timer_l1 Y 0x1000 0x02020000
+ * 0x8: watchdog_l2 Y 0x2000 0x02020000
+ * 0xc: watchdog_l3 Y 0x3000 0x02020000
+ * 0x10: pwm N 0x4000 0x01020000
+ * 0x14: i2s0 Yh 0x5000 0x01030000
+ * 0x18: always 0 - - -
+ * 0x1c: i2s1 Yh 0x6000 0x01030000
+ * 0x20: always 0 - - -
+ * 0x24: qspi N 0x7000 0x01040000
+ * 0x28: uart1 N 0x8000 0x01060000
+ * 0x2c: i2c1 N 0x9000 0x01020000
+ * 0x30: spi0 Y 0xa000 0x01040000
+ * 0x34: timer_lb Y 0xb000 0x02020000
+ * 0x38: timer_lc Y 0xc000 0x02020000
+ * 0x3c: uart2 N 0xd000 0x01060000
+ * 0x40: watchdog_le Y 0xe000 0x02020000
+ * 0x44: timer_lf Y 0xf000 0x02020000
+ * 0x48: spi1 Y 0x10000 0x01040000
+ * 0x4c: timer_l11 Y 0x11000 0x02020000
+ * 0x50: tdm Yh 0x12000 0x01040000
+ *
+ * Registers 0x58, 0x5c, 0x60, 0x64, 0x68 seem to contain more controls for i2s and tdm.
+ *
+ * I am not sure about the device at offset 0x4000 (clk reg 0x10). The ID matches that of i2c, but
+ * it has a larger register set. I suspect it is a PWM device, but I have not seen any ZTE kernel
+ * operate it - even devices with displays only use a GPIO to control the backlight.
+ */
+
+static const char * const timer_lsp_sel[] = {
+ "lsp_osc32k",
+ "lsp_osc26m",
+};
+
+static const char * const uart_lsp_sel[] = {
+ "lsp_osc26m",
+ "lsp_mpll_d6",
+};
+
+static const char * const i2s_lsp_sel[] = {
+ "lsp_osc26m",
+ "lsp_dpll_d4",
+ "lsp_mpll_d6",
+ /* Unknown */
+};
+
+static const char * const tdm_lsp_sel[] = {
+ "lsp_tdm_wclk",
+};
+
+static const char * const spi_lsp_sel[] = {
+ "lsp_osc26m",
+ "lsp_mpll_d4",
+ "lsp_mpll_d6",
+ /* Unknown */
+};
+
+static const char * const qspi_lsp_sel[] = {
+ "lsp_osc26m",
+ "lsp_mpll_d4",
+ "lsp_mpll_d5",
+ "lsp_mpll_d6",
+ "lsp_mpll_d8",
+ "lsp_mpll_d12",
+ "lsp_osc26m",
+ "lsp_osc26m",
+};
+
+static const struct zx_mux_desc zx297520v3_lsp_muxes[] = {
+ MUX(0, "timer_l1_mux", timer_lsp_sel, 0x04, 4, 1),
+ MUX(0, "wdt_l2_mux", timer_lsp_sel, 0x08, 4, 1),
+ MUX(0, "wdt_l3_mux", timer_lsp_sel, 0x0c, 4, 1),
+ /* PWM: No mux bit can be set */
+ MUX(0, "i2s0_mux", i2s_lsp_sel, 0x14, 4, 2),
+ /* 0x18: Always 0 */
+ MUX(0, "i2s1_mux", i2s_lsp_sel, 0x1c, 4, 2),
+ /* 0x20: Always 0 */
+ MUX(0, "qspi_mux", qspi_lsp_sel, 0x24, 4, 3),
+ MUX(0, "uart1_mux", uart_lsp_sel, 0x28, 4, 1),
+ MUX(0, "i2c1_mux", uart_lsp_sel, 0x2c, 4, 1),
+ MUX(0, "spi0_mux", spi_lsp_sel, 0x30, 4, 2),
+ MUX(0, "timer_lb_mux", timer_lsp_sel, 0x34, 4, 1),
+ MUX(0, "timer_lc_mux", timer_lsp_sel, 0x38, 4, 1),
+ MUX(0, "uart2_mux", uart_lsp_sel, 0x3c, 4, 1),
+ MUX(0, "wdt_le_mux", timer_lsp_sel, 0x40, 4, 1),
+ MUX(0, "timer_lf_mux", timer_lsp_sel, 0x44, 4, 1),
+ MUX(0, "spi1_mux", spi_lsp_sel, 0x48, 4, 2),
+ MUX(0, "timer_l11_mux", timer_lsp_sel, 0x4c, 4, 1),
+ /* TDM: No mux in LSP. Instead, it is in matrix with a separate clk line to LSP */
+};
+
+static const struct zx_div_desc zx297520v3_lsp_dividers[] = {
+ DIV(0, "timer_l1_div", "timer_l1_mux", 0x04, 12, 4),
+ DIV(0, "wdt_l2_div", "wdt_l2_mux", 0x08, 12, 4),
+ DIV(0, "wdt_l3_div", "wdt_l3_mux", 0x0c, 12, 4),
+ /* PWM: No div */
+ DIV(0, "i2s0_div", "i2s0_mux", 0x14, 16, 4),
+ /* 0x18: Always 0 */
+ DIV(0, "i2s1_div", "i2s1_mux", 0x1c, 16, 4),
+ /* 0x20: Always 0 */
+ /* qspi, uart1, i2c1: No div */
+ DIV(0, "spi0_div", "spi0_mux", 0x30, 12, 4),
+ DIV(0, "timer_lb_div", "timer_lb_mux", 0x34, 12, 4),
+ DIV(0, "timer_lc_div", "timer_lc_mux", 0x38, 12, 4),
+ /* uart2: No div */
+ DIV(0, "wdt_le_div", "wdt_le_mux", 0x40, 12, 4),
+ DIV(0, "timer_lf_div", "timer_lf_mux", 0x44, 12, 4),
+ DIV(0, "spi1_div", "spi1_mux", 0x48, 12, 4),
+ DIV(0, "timer_l11_div", "timer_l11_mux", 0x4c, 12, 4),
+ DIV(0, "tdm_div", "lsp_tdm_wclk", 0x50, 16, 4),
+};
+
+static const struct zx_gate_desc zx297520v3_lsp_gates[] = {
+ GATE(ZX297520V3_TIMER_L1_WCLK, "timer_l1_wclk", "timer_l1_div", 0x04, 0, 0),
+ GATE(ZX297520V3_TIMER_L1_PCLK, "timer_l1_pclk", "lsp_pclk", 0x04, 1, 0),
+ GATE(ZX297520V3_WDT_L2_WCLK, "wdt_l2_wclk", "wdt_l2_div", 0x08, 0, 0),
+ GATE(ZX297520V3_WDT_L2_PCLK, "wdt_l2_pclk", "lsp_pclk", 0x08, 1, 0),
+ GATE(ZX297520V3_WDT_L3_WCLK, "wdt_l3_wclk", "wdt_l3_div", 0x0c, 0, 0),
+ GATE(ZX297520V3_WDT_L3_PCLK, "wdt_l3_pclk", "lsp_pclk", 0x0c, 1, 0),
+ /* I don't know the LSP parent. It must be one of the LSP inputs though. */
+ GATE(ZX297520V3_PWM_WCLK, "pwm_wclk", "lsp_osc26m", 0x10, 0, 0),
+ GATE(ZX297520V3_PWM_PCLK, "pwm_pclk", "lsp_pclk", 0x10, 1, 0),
+ GATE(ZX297520V3_I2S0_WCLK, "i2s0_wclk", "i2s0_div", 0x14, 0, 0),
+ GATE(ZX297520V3_I2S0_PCLK, "i2s0_pclk", "lsp_pclk", 0x14, 1, 0),
+ /* 0x1c: Always 0 */
+ GATE(ZX297520V3_I2S1_WCLK, "i2s1_wclk", "i2s1_div", 0x1c, 0, 0),
+ GATE(ZX297520V3_I2S1_PCLK, "i2s1_pclk", "lsp_pclk", 0x1c, 1, 0),
+ /* 0x20: Always 0 */
+ GATE(ZX297520V3_QSPI_WCLK, "qspi_wclk", "qspi_mux", 0x24, 0, 0),
+ GATE(ZX297520V3_QSPI_PCLK, "qspi_pclk", "lsp_pclk", 0x24, 1, 0),
+ GATE(ZX297520V3_UART1_WCLK, "uart1_wclk", "uart1_mux", 0x28, 0, 0),
+ GATE(ZX297520V3_UART1_PCLK, "uart1_pclk", "lsp_pclk", 0x28, 1, 0),
+ GATE(ZX297520V3_I2C1_WCLK, "i2c1_wclk", "i2c1_mux", 0x2c, 0, 0),
+ GATE(ZX297520V3_I2C1_PCLK, "i2c1_pclk", "lsp_pclk", 0x2c, 1, 0),
+ GATE(ZX297520V3_SPI0_WCLK, "spi0_wclk", "spi0_div", 0x30, 0, 0),
+ GATE(ZX297520V3_SPI0_PCLK, "spi0_pclk", "lsp_pclk", 0x30, 1, 0),
+ GATE(ZX297520V3_TIMER_LB_WCLK, "timer_lb_wclk", "timer_lb_div", 0x34, 0, 0),
+ GATE(ZX297520V3_TIMER_LB_PCLK, "timer_lb_pclk", "lsp_pclk", 0x34, 1, 0),
+ GATE(ZX297520V3_TIMER_LC_WCLK, "timer_lc_wclk", "timer_lc_div", 0x38, 0, 0),
+ GATE(ZX297520V3_TIMER_LC_PCLK, "timer_lc_pclk", "lsp_pclk", 0x38, 1, 0),
+ GATE(ZX297520V3_UART2_WCLK, "uart2_wclk", "uart2_mux", 0x3c, 0, 0),
+ GATE(ZX297520V3_UART2_PCLK, "uart2_pclk", "lsp_pclk", 0x3c, 1, 0),
+ GATE(ZX297520V3_WDT_LE_WCLK, "wdt_le_wclk", "wdt_le_div", 0x40, 0, 0),
+ GATE(ZX297520V3_WDT_LE_PCLK, "wdt_le_pclk", "lsp_pclk", 0x40, 1, 0),
+ GATE(ZX297520V3_TIMER_LF_WCLK, "timer_lf_wclk", "timer_lf_div", 0x44, 0, 0),
+ GATE(ZX297520V3_TIMER_LF_PCLK, "timer_lf_pclk", "lsp_pclk", 0x44, 1, 0),
+ GATE(ZX297520V3_SPI1_WCLK, "spi1_wclk", "spi1_div", 0x48, 0, 0),
+ GATE(ZX297520V3_SPI1_PCLK, "spi1_pclk", "lsp_pclk", 0x48, 1, 0),
+ GATE(ZX297520V3_TIMER_L11_WCLK, "timer_l11_wclk", "timer_l11_div", 0x4c, 0, 0),
+ GATE(ZX297520V3_TIMER_L11_PCLK, "timer_l11_pclk", "lsp_pclk", 0x4c, 1, 0),
+ GATE(ZX297520V3_TDM_WCLK, "tdm_wclk", "tdm_div", 0x50, 0, 0),
+ GATE(ZX297520V3_TDM_PCLK, "tdm_pclk", "lsp_pclk", 0x50, 1, 0),
+};
+
+static const char * const zx297529v3_lsp_inputs[] = {
+ "mpll_d5", "mpll_d4", "mpll_d6", "mpll_d8", "mpll_d12",
+ "osc26m", "osc32k", "tdm_wclk", "dpll_d4"
+};
+
+static const char * const zx297529v3_lsp_inputs_enable[] = {
+ "pclk"
+};
+
+static const struct zx_clk_data zx297520v3_lspclk_data = {
+ .inputs_enable = zx297529v3_lsp_inputs_enable,
+ .num_inputs_enable = ARRAY_SIZE(zx297529v3_lsp_inputs_enable),
+ .inputs = zx297529v3_lsp_inputs,
+ .num_inputs = ARRAY_SIZE(zx297529v3_lsp_inputs),
+ .muxes = zx297520v3_lsp_muxes,
+ .num_muxes = ARRAY_SIZE(zx297520v3_lsp_muxes),
+ .divs = zx297520v3_lsp_dividers,
+ .num_divs = ARRAY_SIZE(zx297520v3_lsp_dividers),
+ .gates = zx297520v3_lsp_gates,
+ .num_gates = ARRAY_SIZE(zx297520v3_lsp_gates),
+ .reset_auxdev_name = "zx297520v3_lsprst"
+};
+
static const struct of_device_id of_match_zx297520v3[] = {
{ .compatible = "zte,zx297520v3-topclk", .data = &zx297520v3_topclk_data },
{ .compatible = "zte,zx297520v3-matrixclk", .data = &zx297520v3_matrixclk_data },
+ { .compatible = "zte,zx297520v3-lspclk", .data = &zx297520v3_lspclk_data },
{ }
};
MODULE_DEVICE_TABLE(of, of_match_zx297520v3);
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 10/12] reset: zte: Add a zx297520v3 reset driver
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
This drives the auxiliary devices created by the clock driver.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
MAINTAINERS | 1 +
drivers/reset/Kconfig | 11 ++
drivers/reset/Makefile | 1 +
drivers/reset/reset-zte-zx297520v3.c | 224 +++++++++++++++++++++++++++++++++++
4 files changed, 237 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index f1f0459b2c72..55bf0290343a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3871,6 +3871,7 @@ F: Documentation/devicetree/zte,zx297520v3-*
F: arch/arm/boot/dts/zte/
F: arch/arm/mach-zte/
F: drivers/clk/zte/
+F: drivers/reset/reset-zte-zx297520v3.c
F: include/dt-bindings/clock/zte,zx297520v3-clk.h
ARM/ZYNQ ARCHITECTURE
diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
index d009eb0849a3..116dd23f1b8e 100644
--- a/drivers/reset/Kconfig
+++ b/drivers/reset/Kconfig
@@ -404,6 +404,17 @@ config RESET_UNIPHIER_GLUE
on UniPhier SoCs. Say Y if you want to control reset signals
provided by the glue layer.
+config RESET_ZTE_ZX297520V3
+ tristate "ZTE zx297520v3 Reset Driver"
+ depends on (ARCH_ZTE || COMPILE_TEST)
+ default CLK_ZTE_ZX297520V3
+ select AUXILIARY_BUS
+ help
+ This enables the reset controller for ZTE zx297520v3 SoCs. The reset
+ controller is part of the clock controller on this SoC. This driver
+ operates on an auxiliary device exposed by the clock driver. Enable
+ this driver if you plan to boot the kernel on a zx297520v3 based SoC.
+
config RESET_ZYNQ
bool "ZYNQ Reset Driver" if COMPILE_TEST
default ARCH_ZYNQ
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index 3e52569bd276..9a8a48d44dc4 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -50,5 +50,6 @@ obj-$(CONFIG_RESET_TI_TPS380X) += reset-tps380x.o
obj-$(CONFIG_RESET_TN48M_CPLD) += reset-tn48m.o
obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o
obj-$(CONFIG_RESET_UNIPHIER_GLUE) += reset-uniphier-glue.o
+obj-$(CONFIG_RESET_ZTE_ZX297520V3) += reset-zte-zx297520v3.o
obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o
obj-$(CONFIG_RESET_ZYNQMP) += reset-zynqmp.o
diff --git a/drivers/reset/reset-zte-zx297520v3.c b/drivers/reset/reset-zte-zx297520v3.c
new file mode 100644
index 000000000000..2022f4df2ebd
--- /dev/null
+++ b/drivers/reset/reset-zte-zx297520v3.c
@@ -0,0 +1,224 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2026 Stefan Dösinger
+ */
+#include <dt-bindings/clock/zte,zx297520v3-clk.h>
+#include <linux/reset-controller.h>
+#include <linux/platform_device.h>
+#include <linux/auxiliary_bus.h>
+#include <linux/clk-provider.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/iopoll.h>
+#include <linux/delay.h>
+
+struct zte_reset_reg {
+ u32 mask, wait_mask;
+ u16 reg;
+};
+
+struct zte_reset_info {
+ const struct zte_reset_reg *resets;
+ unsigned int num;
+};
+
+struct zte_reset {
+ struct reset_controller_dev rcdev;
+ struct regmap *map;
+ const struct zte_reset_reg *resets;
+};
+
+static inline struct zte_reset *to_zte_reset(struct reset_controller_dev *rcdev)
+{
+ return container_of(rcdev, struct zte_reset, rcdev);
+}
+
+static int zx29_rst_assert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+ struct zte_reset *rst = to_zte_reset(rcdev);
+
+ return regmap_clear_bits(rst->map, rst->resets[id].reg, rst->resets[id].mask);
+}
+
+static int zx29_rst_deassert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+ struct zte_reset *rst = to_zte_reset(rcdev);
+ int res;
+ u32 val;
+
+ res = regmap_set_bits(rst->map, rst->resets[id].reg, rst->resets[id].mask);
+ if (res)
+ return res;
+
+ /* This is a special case used only by USB reset */
+ if (rst->resets[id].wait_mask) {
+ return regmap_read_poll_timeout(rst->map, rst->resets[id].reg + 4, val,
+ val & rst->resets[id].wait_mask, 1, 100);
+ }
+
+ return 0;
+}
+
+static int zx29_rst_status(struct reset_controller_dev *rcdev, unsigned long id)
+{
+ struct zte_reset *rst = to_zte_reset(rcdev);
+ int res;
+
+ res = regmap_test_bits(rst->map, rst->resets[id].reg, rst->resets[id].mask);
+ if (res < 0)
+ return res;
+
+ return !res;
+}
+
+static const struct reset_control_ops zx29_rst_ops = {
+ .assert = zx29_rst_assert,
+ .deassert = zx29_rst_deassert,
+ .status = zx29_rst_status,
+};
+
+static const struct zte_reset_reg zx297520v3_top_resets[] = {
+ /* This bit is set by ZTE's cpko.ko blob, it looks like a reset bit for the LTE DSP
+ * coprocessor. Clocks for it are in matrixclk.
+ */
+ [ZX297520V3_ZSP_RESET] = { .reg = 0x13c, .mask = BIT(0) },
+
+ [ZX297520V3_UART0_RESET] = { .reg = 0x78, .mask = BIT(6) | BIT(7) },
+ [ZX297520V3_I2C0_RESET] = { .reg = 0x74, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_RTC_RESET] = { .reg = 0x74, .mask = BIT(4) | BIT(5) },
+ [ZX297520V3_TIMER_T08_RESET] = { .reg = 0x78, .mask = BIT(4) | BIT(5) },
+ [ZX297520V3_TIMER_T09_RESET] = { .reg = 0x78, .mask = BIT(2) | BIT(3) },
+ [ZX297520V3_PMM_RESET] = { .reg = 0x74, .mask = BIT(0) | BIT(1) },
+
+ /* I haven't found any clocks for GPIO. It probably wouldn't make much
+ * sense anyway. Only one reset bit per controller.
+ */
+ [ZX297520V3_GPIO_RESET] = { .reg = 0x74, .mask = BIT(3) },
+ [ZX297520V3_GPIO8_RESET] = { .reg = 0x74, .mask = BIT(2) },
+
+ [ZX297520V3_TIMER_T12_RESET] = { .reg = 0x74, .mask = BIT(6) | BIT(7) },
+ [ZX297520V3_TIMER_T13_RESET] = { .reg = 0x7c, .mask = BIT(0) | BIT(1) },
+ [ZX297520V3_TIMER_T14_RESET] = { .reg = 0x7c, .mask = BIT(2) | BIT(3) },
+ [ZX297520V3_TIMER_T15_RESET] = { .reg = 0x74, .mask = BIT(10) | BIT(11) },
+ [ZX297520V3_TIMER_T16_RESET] = { .reg = 0x7c, .mask = BIT(4) | BIT(5) },
+ [ZX297520V3_TIMER_T17_RESET] = { .reg = 0x12c, .mask = BIT(0) | BIT(1) },
+ [ZX297520V3_WDT_T18_RESET] = { .reg = 0x74, .mask = BIT(12) | BIT(13) },
+ [ZX297520V3_USIM1_RESET] = { .reg = 0x74, .mask = BIT(14) | BIT(15) },
+ [ZX297520V3_AHB_RESET] = { .reg = 0x70, .mask = BIT(0) | BIT(1) },
+
+ /* USB reset. This is slightly special because it needs to wait for a ready bit after
+ * deasserting.
+ */
+ [ZX297520V3_USB_RESET] = { .reg = 0x80, .mask = BIT(3) | BIT(4) | BIT(5),
+ .wait_mask = BIT(1)},
+ [ZX297520V3_HSIC_RESET] = { .reg = 0x80, .mask = BIT(0) | BIT(1) | BIT(2),
+ .wait_mask = BIT(0)},
+};
+
+static const struct zte_reset_info zx297520v3_top_info = {
+ .resets = zx297520v3_top_resets,
+ .num = ARRAY_SIZE(zx297520v3_top_resets),
+};
+
+static const struct zte_reset_reg zx297520v3_matrix_resets[] = {
+ [ZX297520V3_CPU_RESET] = { .reg = 0x28, .mask = BIT(1) },
+ [ZX297520V3_EDCP_RESET] = { .reg = 0x68, .mask = BIT(0) },
+ [ZX297520V3_SD0_RESET] = { .reg = 0x58, .mask = BIT(1) },
+ [ZX297520V3_SD1_RESET] = { .reg = 0x58, .mask = BIT(0) },
+ [ZX297520V3_NAND_RESET] = { .reg = 0x58, .mask = BIT(4) },
+ [ZX297520V3_PDCFG_RESET] = { .reg = 0x94, .mask = BIT(20) },
+ [ZX297520V3_SSC_RESET] = { .reg = 0x94, .mask = BIT(24) },
+ [ZX297520V3_GMAC_RESET] = { .reg = 0x114, .mask = BIT(0) | BIT(1) },
+ [ZX297520V3_VOU_RESET] = { .reg = 0x16c, .mask = BIT(0) },
+};
+
+static const struct zte_reset_info zx297520v3_matrix_info = {
+ .resets = zx297520v3_matrix_resets,
+ .num = ARRAY_SIZE(zx297520v3_matrix_resets),
+};
+
+static const struct zte_reset_reg zx297520v3_lsp_resets[] = {
+ [ZX297520V3_TIMER_L1_RESET] = { .reg = 0x04, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_WDT_L2_RESET] = { .reg = 0x08, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_WDT_L3_RESET] = { .reg = 0x0c, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_PWM_RESET] = { .reg = 0x10, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_I2S0_RESET] = { .reg = 0x14, .mask = BIT(8) | BIT(9) },
+ /* 0x18: Not writeable */
+ [ZX297520V3_I2S1_RESET] = { .reg = 0x1c, .mask = BIT(8) | BIT(9) },
+ /* 0x20: Not writeable */
+ [ZX297520V3_QSPI_RESET] = { .reg = 0x24, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_UART1_RESET] = { .reg = 0x28, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_I2C1_RESET] = { .reg = 0x2c, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_SPI0_RESET] = { .reg = 0x30, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_TIMER_LB_RESET] = { .reg = 0x34, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_TIMER_LC_RESET] = { .reg = 0x38, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_UART2_RESET] = { .reg = 0x3c, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_WDT_LE_RESET] = { .reg = 0x40, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_TIMER_LF_RESET] = { .reg = 0x44, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_SPI1_RESET] = { .reg = 0x48, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_TIMER_L11_RESET] = { .reg = 0x4c, .mask = BIT(8) | BIT(9) },
+ [ZX297520V3_TDM_RESET] = { .reg = 0x50, .mask = BIT(8) | BIT(9) },
+};
+
+static const struct zte_reset_info zx297520v3_lsp_info = {
+ .resets = zx297520v3_lsp_resets,
+ .num = ARRAY_SIZE(zx297520v3_lsp_resets),
+};
+
+static int reset_zx297520v3_probe(struct auxiliary_device *adev,
+ const struct auxiliary_device_id *id)
+{
+ const struct zte_reset_info *drv_info;
+ struct device *dev = &adev->dev;
+ struct zte_reset *rst;
+
+ drv_info = (struct zte_reset_info *)id->driver_data;
+
+ rst = devm_kzalloc(dev, sizeof(*rst), GFP_KERNEL);
+ if (!rst)
+ return -ENOMEM;
+
+ rst->resets = drv_info->resets;
+ rst->rcdev.owner = THIS_MODULE;
+ rst->rcdev.nr_resets = drv_info->num;
+ rst->rcdev.ops = &zx29_rst_ops;
+ rst->rcdev.of_node = dev->of_node;
+ rst->rcdev.dev = dev;
+ rst->rcdev.of_reset_n_cells = 1;
+
+ rst->map = device_node_to_regmap(dev->of_node);
+ if (IS_ERR(rst->map))
+ return dev_err_probe(dev, PTR_ERR(rst->map), "Cannot get parent syscon regmap\n");
+
+ return devm_reset_controller_register(dev, &rst->rcdev);
+}
+
+static const struct auxiliary_device_id reset_zx297520v3_ids[] = {
+ {
+ .name = "clk_zte.zx297520v3_toprst",
+ .driver_data = (kernel_ulong_t)&zx297520v3_top_info,
+ },
+ {
+ .name = "clk_zte.zx297520v3_matrixrst",
+ .driver_data = (kernel_ulong_t)&zx297520v3_matrix_info,
+ },
+ {
+ .name = "clk_zte.zx297520v3_lsprst",
+ .driver_data = (kernel_ulong_t)&zx297520v3_lsp_info,
+ },
+ { },
+};
+
+MODULE_DEVICE_TABLE(auxiliary, reset_zx297520v3_ids);
+
+static struct auxiliary_driver reset_zx297520v3_drv = {
+ .name = "zx297520v3_reset",
+ .id_table = reset_zx297520v3_ids,
+ .probe = reset_zx297520v3_probe,
+};
+
+module_auxiliary_driver(reset_zx297520v3_drv);
+
+MODULE_AUTHOR("Stefan Dösinger <stefandoesinger@gmail.com>");
+MODULE_DESCRIPTION("ZTE zx297520v3 reset driver");
+MODULE_LICENSE("GPL");
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 11/12] ARM: dts: zte: Declare zx297520v3 clock device nodes
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
This makes use of the driver added in the previous patches. It wires up
the uart clocks and resets and allows getting rid of the placeholder
uartclk node.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
arch/arm/boot/dts/zte/zx297520v3.dtsi | 90 +++++++++++++++++++++++++++++++----
1 file changed, 81 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/zte/zx297520v3.dtsi b/arch/arm/boot/dts/zte/zx297520v3.dtsi
index a16c30a164bb..a2b6909e7434 100644
--- a/arch/arm/boot/dts/zte/zx297520v3.dtsi
+++ b/arch/arm/boot/dts/zte/zx297520v3.dtsi
@@ -4,6 +4,7 @@
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/zte,zx297520v3-clk.h>
/ {
#address-cells = <1>;
@@ -20,13 +21,16 @@ cpu@0 {
};
};
- /* Base bus clock and default for the UART. It will be replaced once a clock driver has
- * been added.
- */
- uartclk: uartclk-26000000 {
- #clock-cells = <0>;
+ osc26m: osc26m {
compatible = "fixed-clock";
clock-frequency = <26000000>;
+ #clock-cells = <0>;
+ };
+
+ osc32k: osc32k {
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ #clock-cells = <0>;
};
timer {
@@ -70,13 +74,80 @@ gic: interrupt-controller@f2000000 {
<0xf2040000 0x20000>;
};
+ topclk: clock-controller@13b000 {
+ compatible = "zte,zx297520v3-topclk", "syscon";
+ reg = <0x0013b000 0x400>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ clocks = <&osc26m>, <&osc32k>;
+ clock-names = "osc26m", "osc32k";
+ };
+
+ matrixclk: clock-controller@1306000 {
+ compatible = "zte,zx297520v3-matrixclk", "syscon";
+ reg = <0x01306000 0x400>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ clocks = <&osc26m>, <&osc32k>,
+ <&topclk ZX297520V3_MPLL>, <&topclk ZX297520V3_MPLL_D2>,
+ <&topclk ZX297520V3_MPLL_D3>, <&topclk ZX297520V3_MPLL_D4>,
+ <&topclk ZX297520V3_MPLL_D5>, <&topclk ZX297520V3_MPLL_D6>,
+ <&topclk ZX297520V3_MPLL_D8>, <&topclk ZX297520V3_MPLL_D12>,
+ <&topclk ZX297520V3_MPLL_D16>, <&topclk ZX297520V3_MPLL_D26>,
+ <&topclk ZX297520V3_UPLL>, <&topclk ZX297520V3_UPLL_D2>,
+ <&topclk ZX297520V3_UPLL_D3>, <&topclk ZX297520V3_UPLL_D4>,
+ <&topclk ZX297520V3_UPLL_D5>, <&topclk ZX297520V3_UPLL_D6>,
+ <&topclk ZX297520V3_UPLL_D8>, <&topclk ZX297520V3_UPLL_D12>,
+ <&topclk ZX297520V3_UPLL_D16>,
+ <&topclk ZX297520V3_DPLL>, <&topclk ZX297520V3_DPLL_D2>,
+ <&topclk ZX297520V3_DPLL_D3>, <&topclk ZX297520V3_DPLL_D4>,
+ <&topclk ZX297520V3_DPLL_D5>, <&topclk ZX297520V3_DPLL_D6>,
+ <&topclk ZX297520V3_DPLL_D8>, <&topclk ZX297520V3_DPLL_D12>,
+ <&topclk ZX297520V3_DPLL_D16>,
+ <&topclk ZX297520V3_GPLL>, <&topclk ZX297520V3_GPLL_D2>,
+ <&topclk ZX297520V3_GPLL_D3>, <&topclk ZX297520V3_GPLL_D4>,
+ <&topclk ZX297520V3_GPLL_D5>, <&topclk ZX297520V3_GPLL_D6>,
+ <&topclk ZX297520V3_GPLL_D8>, <&topclk ZX297520V3_GPLL_D12>,
+ <&topclk ZX297520V3_GPLL_D16>;
+ clock-names = "osc26m", "osc32k", "mpll", "mpll_d2", "mpll_d3", "mpll_d4",
+ "mpll_d5", "mpll_d6", "mpll_d8", "mpll_d12", "mpll_d16",
+ "mpll_d26", "upll", "upll_d2", "upll_d3", "upll_d4",
+ "upll_d5", "upll_d6", "upll_d8", "upll_d12", "upll_d16",
+ "dpll", "dpll_d2", "dpll_d3", "dpll_d4", "dpll_d5", "dpll_d6",
+ "dpll_d8", "dpll_d12", "dpll_d16", "gpll", "gpll_d2",
+ "gpll_d3", "gpll_d4", "gpll_d5", "gpll_d6", "gpll_d8",
+ "gpll_d12", "gpll_d16";
+ };
+
+ lspclk: clock-controller@1400000 {
+ compatible = "zte,zx297520v3-lspclk";
+ reg = <0x01400000 0x100>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+
+ clocks = <&matrixclk ZX297520V3_LSP_MPLL_D5_WCLK>,
+ <&matrixclk ZX297520V3_LSP_MPLL_D4_WCLK>,
+ <&matrixclk ZX297520V3_LSP_MPLL_D6_WCLK>,
+ <&matrixclk ZX297520V3_LSP_MPLL_D8_WCLK>,
+ <&matrixclk ZX297520V3_LSP_MPLL_D12_WCLK>,
+ <&matrixclk ZX297520V3_LSP_OSC26M_WCLK>,
+ <&matrixclk ZX297520V3_LSP_OSC32K_WCLK>,
+ <&matrixclk ZX297520V3_LSP_PCLK>,
+ <&matrixclk ZX297520V3_LSP_TDM_WCLK>,
+ <&matrixclk ZX297520V3_LSP_DPLL_D4_WCLK>;
+ clock-names = "mpll_d5", "mpll_d4", "mpll_d6", "mpll_d8", "mpll_d12",
+ "osc26m", "osc32k", "pclk", "tdm_wclk", "dpll_d4";
+ };
+
+
uart0: serial@131000 {
compatible = "arm,pl011", "arm,primecell";
arm,primecell-periphid = <0x0018c011>;
reg = <0x00131000 0x1000>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&uartclk>, <&uartclk>;
+ clocks = <&topclk ZX297520V3_UART0_WCLK>, <&topclk ZX297520V3_UART0_PCLK>;
clock-names = "uartclk", "apb_pclk";
+ resets = <&topclk ZX297520V3_UART0_RESET>;
status = "disabled";
};
@@ -85,8 +156,9 @@ uart1: serial@1408000 {
arm,primecell-periphid = <0x0018c011>;
reg = <0x01408000 0x1000>;
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&uartclk>, <&uartclk>;
+ clocks = <&lspclk ZX297520V3_UART1_WCLK>, <&lspclk ZX297520V3_UART1_PCLK>;
clock-names = "uartclk", "apb_pclk";
+ resets = <&lspclk ZX297520V3_UART1_RESET>;
status = "disabled";
};
@@ -94,9 +166,9 @@ uart2: serial@140d000 {
compatible = "arm,pl011", "arm,primecell";
arm,primecell-periphid = <0x0018c011>;
reg = <0x0140d000 0x1000>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&uartclk>, <&uartclk>;
+ clocks = <&lspclk ZX297520V3_UART2_WCLK>, <&lspclk ZX297520V3_UART2_PCLK>;
clock-names = "uartclk", "apb_pclk";
+ resets = <&lspclk ZX297520V3_UART2_RESET>;
status = "disabled";
};
};
--
2.53.0
^ permalink raw reply related
* [PATCH RFC v4 12/12] ARM: dts: zte: Add a syscon-reboot for zx297520v3 boards
From: Stefan Dösinger @ 2026-06-16 20:26 UTC (permalink / raw)
To: Michael Turquette, Stephen Boyd, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Philipp Zabel, Brian Masney
Cc: linux-clk, devicetree, linux-kernel, linux-arm-kernel,
Stefan Dösinger
In-Reply-To: <20260616-zx29clk-v4-0-ca994bd22e9d@gmail.com>
This is fairly simple with the driver exposing a syscon regmap. Write a
one to the lowest bit of register 0 and the board resets.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
---
arch/arm/boot/dts/zte/zx297520v3.dtsi | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/arch/arm/boot/dts/zte/zx297520v3.dtsi b/arch/arm/boot/dts/zte/zx297520v3.dtsi
index a2b6909e7434..013ece51c2a0 100644
--- a/arch/arm/boot/dts/zte/zx297520v3.dtsi
+++ b/arch/arm/boot/dts/zte/zx297520v3.dtsi
@@ -33,6 +33,13 @@ osc32k: osc32k {
#clock-cells = <0>;
};
+ syscon-reboot {
+ compatible = "syscon-reboot";
+ regmap = <&topclk>;
+ offset = <0x0>;
+ mask = <0x1>;
+ };
+
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
--
2.53.0
^ permalink raw reply related
* Re: [PATCH 5/13] ASoC: qcom: Add QAIF shared data structures and variant interface
From: Srinivas Kandagatla @ 2026-06-16 20:28 UTC (permalink / raw)
To: Harendra Gautam, Srinivas Kandagatla
Cc: Mark Brown, Liam Girdwood, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-sound, linux-arm-msm, devicetree,
linux-kernel
In-Reply-To: <20260605103739.3557573-6-harendra.gautam@oss.qualcomm.com>
On 6/5/26 11:37 AM, Harendra Gautam wrote:
>
> + struct reg_field cif_rddma_shram_wm;
> + struct reg_field cif_rddma_active_ch_en;
> + struct reg_field cif_rddma_fs_sel;
> + struct reg_field cif_rddma_fs_delay;
> + struct reg_field cif_rddma_fs_out_gate;
> + struct reg_field cif_rddma_intf_dyncclk;
> + struct reg_field cif_rddma_en_16bit_unpack;
> +
Why do we need to use reg_field?, currently this patchset only supports
one SoC. reg_field makes sense only when there is change in bit
positions across SoCs and if we want to leverage from existing driver.
--srini
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox