[PATCH net-next 00/11][pull request] Intel Wired LAN Driver Updates 2026-07-01 (igc, igb)

[PATCH net-next 00/11][pull request] Intel Wired LAN Driver Updates 2026-07-01 (igc, igb)

[Tony Nguyen]

Kohei Enju adds ethtool support for get/set hash key on igc and adds
setting of skb hash type based on values from Rx descriptor on igb.

Takashi Kozu adds ethtool support for get/set hash key on igb.

Faizal adds support for forcing link speed via ethtool when
autonegotiation is disabled on the igc driver.

The following are changes since commit d6e81529749190123aa0040626c7e5dbc20fdc9a:
  Merge branch 'net-fib_rules-rtnl-less-rtm_newrule-and-rtm_delrule'
and are available in the git repository at:
  git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue 1GbE

Faizal Rahim (4):
  igc: remove unused autoneg_failed field
  igc: move autoneg-enabled settings into igc_handle_autoneg_enabled()
  igc: replace goto out with direct returns in
    igc_config_fc_after_link_up()
  igc: add support for forcing link speed without autonegotiation

Kohei Enju (4):
  igc: prepare for RSS key get/set support
  igc: expose RSS key via ethtool get_rxfh
  igc: allow configuring RSS key via ethtool set_rxfh
  igb: set skb hash type from RSS_TYPE

Takashi Kozu (3):
  igb: prepare for RSS key get/set support
  igb: expose RSS key via ethtool get_rxfh
  igb: allow configuring RSS key via ethtool set_rxfh

 drivers/net/ethernet/intel/igb/e1000_82575.h |  21 ++
 drivers/net/ethernet/intel/igb/igb.h         |   3 +
 drivers/net/ethernet/intel/igb/igb_ethtool.c |  85 ++++--
 drivers/net/ethernet/intel/igb/igb_main.c    |  25 +-
 drivers/net/ethernet/intel/igc/igc.h         |   3 +
 drivers/net/ethernet/intel/igc/igc_base.c    |  35 ++-
 drivers/net/ethernet/intel/igc/igc_defines.h |   9 +-
 drivers/net/ethernet/intel/igc/igc_ethtool.c | 277 +++++++++++++------
 drivers/net/ethernet/intel/igc/igc_hw.h      |  10 +-
 drivers/net/ethernet/intel/igc/igc_mac.c     |  35 ++-
 drivers/net/ethernet/intel/igc/igc_main.c    |  10 +-
 drivers/net/ethernet/intel/igc/igc_phy.c     |  65 ++++-
 drivers/net/ethernet/intel/igc/igc_phy.h     |   1 +
 13 files changed, 425 insertions(+), 154 deletions(-)

-- 
2.47.1

[PATCH net-next 01/11] igc: prepare for RSS key get/set support

[Tony Nguyen]

From: Kohei Enju <kohei@enjuk.jp>

Store the RSS key inside struct igc_adapter and introduce the
igc_write_rss_key() helper function. This allows the driver to program
the RSSRK registers using a persistent RSS key, instead of using a
stack-local buffer in igc_setup_mrqc().

This is a preparation patch for adding RSS key get/set support in
subsequent changes, and no functional change is intended in this patch.

Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igc/igc.h         |  3 +++
 drivers/net/ethernet/intel/igc/igc_ethtool.c | 20 ++++++++++++++++++++
 drivers/net/ethernet/intel/igc/igc_main.c    |  8 ++++----
 3 files changed, 27 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/igc/igc.h b/drivers/net/ethernet/intel/igc/igc.h
index 46d625b15f44..17f213cc93e4 100644
--- a/drivers/net/ethernet/intel/igc/igc.h
+++ b/drivers/net/ethernet/intel/igc/igc.h
@@ -30,6 +30,7 @@ void igc_ethtool_set_ops(struct net_device *);
 
 #define MAX_ETYPE_FILTER		8
 #define IGC_RETA_SIZE			128
+#define IGC_RSS_KEY_SIZE		40
 
 /* SDP support */
 #define IGC_N_EXTTS	2
@@ -302,6 +303,7 @@ struct igc_adapter {
 	unsigned int nfc_rule_count;
 
 	u8 rss_indir_tbl[IGC_RETA_SIZE];
+	u8 rss_key[IGC_RSS_KEY_SIZE];
 
 	unsigned long link_check_timeout;
 	struct igc_info ei;
@@ -361,6 +363,7 @@ unsigned int igc_get_max_rss_queues(struct igc_adapter *adapter);
 void igc_set_flag_queue_pairs(struct igc_adapter *adapter,
 			      const u32 max_rss_queues);
 int igc_reinit_queues(struct igc_adapter *adapter);
+void igc_write_rss_key(struct igc_adapter *adapter);
 void igc_write_rss_indir_tbl(struct igc_adapter *adapter);
 bool igc_has_link(struct igc_adapter *adapter);
 void igc_reset(struct igc_adapter *adapter);
diff --git a/drivers/net/ethernet/intel/igc/igc_ethtool.c b/drivers/net/ethernet/intel/igc/igc_ethtool.c
index 0122009bedd0..f01222f12776 100644
--- a/drivers/net/ethernet/intel/igc/igc_ethtool.c
+++ b/drivers/net/ethernet/intel/igc/igc_ethtool.c
@@ -1460,6 +1460,26 @@ static int igc_ethtool_set_rxnfc(struct net_device *dev,
 	}
 }
 
+/**
+ * igc_write_rss_key - Program the RSS key into device registers
+ * @adapter: board private structure
+ *
+ * Write the RSS key stored in adapter->rss_key to the IGC_RSSRK registers.
+ * Each 32-bit chunk of the key is read using get_unaligned_le32() and written
+ * to the appropriate register.
+ */
+void igc_write_rss_key(struct igc_adapter *adapter)
+{
+	struct igc_hw *hw = &adapter->hw;
+	u32 val;
+	int i;
+
+	for (i = 0; i < IGC_RSS_KEY_SIZE / 4; i++) {
+		val = get_unaligned_le32(&adapter->rss_key[i * 4]);
+		wr32(IGC_RSSRK(i), val);
+	}
+}
+
 void igc_write_rss_indir_tbl(struct igc_adapter *adapter)
 {
 	struct igc_hw *hw = &adapter->hw;
diff --git a/drivers/net/ethernet/intel/igc/igc_main.c b/drivers/net/ethernet/intel/igc/igc_main.c
index 2c9e2dfd8499..5ef229a5931f 100644
--- a/drivers/net/ethernet/intel/igc/igc_main.c
+++ b/drivers/net/ethernet/intel/igc/igc_main.c
@@ -785,11 +785,8 @@ static void igc_setup_mrqc(struct igc_adapter *adapter)
 	struct igc_hw *hw = &adapter->hw;
 	u32 j, num_rx_queues;
 	u32 mrqc, rxcsum;
-	u32 rss_key[10];
 
-	netdev_rss_key_fill(rss_key, sizeof(rss_key));
-	for (j = 0; j < 10; j++)
-		wr32(IGC_RSSRK(j), rss_key[j]);
+	igc_write_rss_key(adapter);
 
 	num_rx_queues = adapter->rss_queues;
 
@@ -5048,6 +5045,9 @@ static int igc_sw_init(struct igc_adapter *adapter)
 
 	pci_read_config_word(pdev, PCI_COMMAND, &hw->bus.pci_cmd_word);
 
+	/* init RSS key */
+	netdev_rss_key_fill(adapter->rss_key, sizeof(adapter->rss_key));
+
 	/* set default ring sizes */
 	adapter->tx_ring_count = IGC_DEFAULT_TXD;
 	adapter->rx_ring_count = IGC_DEFAULT_RXD;
-- 
2.47.1

[PATCH net-next 02/11] igc: expose RSS key via ethtool get_rxfh

[Tony Nguyen]

From: Kohei Enju <kohei@enjuk.jp>

Implement igc_ethtool_get_rxfh_key_size() and extend
igc_ethtool_get_rxfh() to return the RSS key to userspace.

This can be tested using `ethtool -x <dev>`.

Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igc/igc_ethtool.c | 17 +++++++++++++----
 1 file changed, 13 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/igc/igc_ethtool.c b/drivers/net/ethernet/intel/igc/igc_ethtool.c
index f01222f12776..0e76ffe7be65 100644
--- a/drivers/net/ethernet/intel/igc/igc_ethtool.c
+++ b/drivers/net/ethernet/intel/igc/igc_ethtool.c
@@ -1502,6 +1502,11 @@ void igc_write_rss_indir_tbl(struct igc_adapter *adapter)
 	}
 }
 
+static u32 igc_ethtool_get_rxfh_key_size(struct net_device *netdev)
+{
+	return IGC_RSS_KEY_SIZE;
+}
+
 static u32 igc_ethtool_get_rxfh_indir_size(struct net_device *netdev)
 {
 	return IGC_RETA_SIZE;
@@ -1514,10 +1519,13 @@ static int igc_ethtool_get_rxfh(struct net_device *netdev,
 	int i;
 
 	rxfh->hfunc = ETH_RSS_HASH_TOP;
-	if (!rxfh->indir)
-		return 0;
-	for (i = 0; i < IGC_RETA_SIZE; i++)
-		rxfh->indir[i] = adapter->rss_indir_tbl[i];
+
+	if (rxfh->indir)
+		for (i = 0; i < IGC_RETA_SIZE; i++)
+			rxfh->indir[i] = adapter->rss_indir_tbl[i];
+
+	if (rxfh->key)
+		memcpy(rxfh->key, adapter->rss_key, sizeof(adapter->rss_key));
 
 	return 0;
 }
@@ -2195,6 +2203,7 @@ static const struct ethtool_ops igc_ethtool_ops = {
 	.get_rxnfc		= igc_ethtool_get_rxnfc,
 	.set_rxnfc		= igc_ethtool_set_rxnfc,
 	.get_rx_ring_count	= igc_ethtool_get_rx_ring_count,
+	.get_rxfh_key_size	= igc_ethtool_get_rxfh_key_size,
 	.get_rxfh_indir_size	= igc_ethtool_get_rxfh_indir_size,
 	.get_rxfh		= igc_ethtool_get_rxfh,
 	.set_rxfh		= igc_ethtool_set_rxfh,
-- 
2.47.1

[PATCH net-next 03/11] igc: allow configuring RSS key via ethtool set_rxfh

[Tony Nguyen]

From: Kohei Enju <kohei@enjuk.jp>

Change igc_ethtool_set_rxfh() to accept and save a userspace-provided
RSS key. When a key is provided, store it in the adapter and write the
RSSRK registers accordingly.

This can be tested using `ethtool -X <dev> hkey <key>`.

Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igc/igc_ethtool.c | 30 +++++++++++---------
 1 file changed, 17 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/intel/igc/igc_ethtool.c b/drivers/net/ethernet/intel/igc/igc_ethtool.c
index 0e76ffe7be65..fbba3e84673a 100644
--- a/drivers/net/ethernet/intel/igc/igc_ethtool.c
+++ b/drivers/net/ethernet/intel/igc/igc_ethtool.c
@@ -1539,24 +1539,28 @@ static int igc_ethtool_set_rxfh(struct net_device *netdev,
 	int i;
 
 	/* We do not allow change in unsupported parameters */
-	if (rxfh->key ||
-	    (rxfh->hfunc != ETH_RSS_HASH_NO_CHANGE &&
-	     rxfh->hfunc != ETH_RSS_HASH_TOP))
+	if (rxfh->hfunc != ETH_RSS_HASH_NO_CHANGE &&
+	    rxfh->hfunc != ETH_RSS_HASH_TOP)
 		return -EOPNOTSUPP;
-	if (!rxfh->indir)
-		return 0;
 
-	num_queues = adapter->rss_queues;
+	if (rxfh->indir) {
+		num_queues = adapter->rss_queues;
 
-	/* Verify user input. */
-	for (i = 0; i < IGC_RETA_SIZE; i++)
-		if (rxfh->indir[i] >= num_queues)
-			return -EINVAL;
+		/* Verify user input. */
+		for (i = 0; i < IGC_RETA_SIZE; i++)
+			if (rxfh->indir[i] >= num_queues)
+				return -EINVAL;
 
-	for (i = 0; i < IGC_RETA_SIZE; i++)
-		adapter->rss_indir_tbl[i] = rxfh->indir[i];
+		for (i = 0; i < IGC_RETA_SIZE; i++)
+			adapter->rss_indir_tbl[i] = rxfh->indir[i];
 
-	igc_write_rss_indir_tbl(adapter);
+		igc_write_rss_indir_tbl(adapter);
+	}
+
+	if (rxfh->key) {
+		memcpy(adapter->rss_key, rxfh->key, sizeof(adapter->rss_key));
+		igc_write_rss_key(adapter);
+	}
 
 	return 0;
 }
-- 
2.47.1

[PATCH net-next 04/11] igb: prepare for RSS key get/set support

[Tony Nguyen]

From: Takashi Kozu <takkozu@amazon.com>

Store the RSS key inside struct igb_adapter and introduce the
igb_write_rss_key() helper function. This allows the driver to program
the E1000 registers using a persistent RSS key, instead of using a
stack-local buffer in igb_setup_mrqc().

Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Takashi Kozu <takkozu@amazon.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igb/igb.h         |  3 +++
 drivers/net/ethernet/intel/igb/igb_ethtool.c | 21 ++++++++++++++++++++
 drivers/net/ethernet/intel/igb/igb_main.c    |  8 ++++----
 3 files changed, 28 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/igb/igb.h b/drivers/net/ethernet/intel/igb/igb.h
index 0fff1df81b7b..8c9b02058cec 100644
--- a/drivers/net/ethernet/intel/igb/igb.h
+++ b/drivers/net/ethernet/intel/igb/igb.h
@@ -495,6 +495,7 @@ struct hwmon_buff {
 #define IGB_N_PEROUT	2
 #define IGB_N_SDP	4
 #define IGB_RETA_SIZE	128
+#define IGB_RSS_KEY_SIZE	40
 
 enum igb_filter_match_flags {
 	IGB_FILTER_FLAG_ETHER_TYPE = 0x1,
@@ -655,6 +656,7 @@ struct igb_adapter {
 	struct i2c_client *i2c_client;
 	u32 rss_indir_tbl_init;
 	u8 rss_indir_tbl[IGB_RETA_SIZE];
+	u8 rss_key[IGB_RSS_KEY_SIZE];
 
 	unsigned long link_check_timeout;
 	int copper_tries;
@@ -735,6 +737,7 @@ void igb_down(struct igb_adapter *);
 void igb_reinit_locked(struct igb_adapter *);
 void igb_reset(struct igb_adapter *);
 int igb_reinit_queues(struct igb_adapter *);
+void igb_write_rss_key(struct igb_adapter *adapter);
 void igb_write_rss_indir_tbl(struct igb_adapter *);
 int igb_set_spd_dplx(struct igb_adapter *, u32, u8);
 int igb_setup_tx_resources(struct igb_ring *);
diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index f7938c1da835..9a105e59f432 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -3019,6 +3019,27 @@ static int igb_set_rxnfc(struct net_device *dev, struct ethtool_rxnfc *cmd)
 	return ret;
 }
 
+/**
+ * igb_write_rss_key - Program the RSS key into device registers
+ * @adapter: board private structure
+ *
+ * Write the RSS key stored in adapter->rss_key to the E1000 hardware registers.
+ * Each 32-bit chunk of the key is read using get_unaligned_le32() and written
+ * to the appropriate register.
+ */
+void igb_write_rss_key(struct igb_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+
+	ASSERT_RTNL();
+
+	for (int i = 0; i < IGB_RSS_KEY_SIZE / 4; i++) {
+		u32 val = get_unaligned_le32(&adapter->rss_key[i * 4]);
+
+		wr32(E1000_RSSRK(i), val);
+	}
+}
+
 static int igb_get_eee(struct net_device *netdev, struct ethtool_keee *edata)
 {
 	struct igb_adapter *adapter = netdev_priv(netdev);
diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c
index a1e89a375744..b7d36dd0b8e4 100644
--- a/drivers/net/ethernet/intel/igb/igb_main.c
+++ b/drivers/net/ethernet/intel/igb/igb_main.c
@@ -4048,6 +4048,9 @@ static int igb_sw_init(struct igb_adapter *adapter)
 
 	pci_read_config_word(pdev, PCI_COMMAND, &hw->bus.pci_cmd_word);
 
+	/* init RSS key */
+	netdev_rss_key_fill(adapter->rss_key, sizeof(adapter->rss_key));
+
 	/* set default ring sizes */
 	adapter->tx_ring_count = IGB_DEFAULT_TXD;
 	adapter->rx_ring_count = IGB_DEFAULT_RXD;
@@ -4522,11 +4525,8 @@ static void igb_setup_mrqc(struct igb_adapter *adapter)
 	struct e1000_hw *hw = &adapter->hw;
 	u32 mrqc, rxcsum;
 	u32 j, num_rx_queues;
-	u32 rss_key[10];
 
-	netdev_rss_key_fill(rss_key, sizeof(rss_key));
-	for (j = 0; j < 10; j++)
-		wr32(E1000_RSSRK(j), rss_key[j]);
+	igb_write_rss_key(adapter);
 
 	num_rx_queues = adapter->rss_queues;
 
-- 
2.47.1

[PATCH net-next 05/11] igb: expose RSS key via ethtool get_rxfh

[Tony Nguyen]

From: Takashi Kozu <takkozu@amazon.com>

Implement igb_get_rxfh_key_size() and extend
igb_get_rxfh() to return the RSS key to userspace.

This can be tested using `ethtool -x <dev>`.

Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Takashi Kozu <takkozu@amazon.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igb/igb_ethtool.c | 16 ++++++++++++----
 1 file changed, 12 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index 9a105e59f432..47fc620026a9 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -3297,10 +3297,12 @@ static int igb_get_rxfh(struct net_device *netdev,
 	int i;
 
 	rxfh->hfunc = ETH_RSS_HASH_TOP;
-	if (!rxfh->indir)
-		return 0;
-	for (i = 0; i < IGB_RETA_SIZE; i++)
-		rxfh->indir[i] = adapter->rss_indir_tbl[i];
+	if (rxfh->indir)
+		for (i = 0; i < IGB_RETA_SIZE; i++)
+			rxfh->indir[i] = adapter->rss_indir_tbl[i];
+
+	if (rxfh->key)
+		memcpy(rxfh->key, adapter->rss_key, sizeof(adapter->rss_key));
 
 	return 0;
 }
@@ -3340,6 +3342,11 @@ void igb_write_rss_indir_tbl(struct igb_adapter *adapter)
 	}
 }
 
+static u32 igb_get_rxfh_key_size(struct net_device *netdev)
+{
+	return IGB_RSS_KEY_SIZE;
+}
+
 static int igb_set_rxfh(struct net_device *netdev,
 			struct ethtool_rxfh_param *rxfh,
 			struct netlink_ext_ack *extack)
@@ -3504,6 +3511,7 @@ static const struct ethtool_ops igb_ethtool_ops = {
 	.get_module_eeprom	= igb_get_module_eeprom,
 	.get_rxfh_indir_size	= igb_get_rxfh_indir_size,
 	.get_rxfh		= igb_get_rxfh,
+	.get_rxfh_key_size	= igb_get_rxfh_key_size,
 	.set_rxfh		= igb_set_rxfh,
 	.get_rxfh_fields	= igb_get_rxfh_fields,
 	.set_rxfh_fields	= igb_set_rxfh_fields,
-- 
2.47.1

[PATCH net-next 06/11] igb: allow configuring RSS key via ethtool set_rxfh

[Tony Nguyen]

From: Takashi Kozu <takkozu@amazon.com>

Change igb_set_rxfh() to accept and save a userspace-provided
RSS key. When a key is provided, store it in the adapter and write the
E1000 registers accordingly.

This can be tested using `ethtool -X <dev> hkey <key>`.

Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Takashi Kozu <takkozu@amazon.com>
Tested-by: Kohei Enju <kohei@enjuk.jp>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igb/igb_ethtool.c | 48 +++++++++++---------
 1 file changed, 26 insertions(+), 22 deletions(-)

diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index 47fc620026a9..65014a54a6d1 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -3357,35 +3357,39 @@ static int igb_set_rxfh(struct net_device *netdev,
 	u32 num_queues;
 
 	/* We do not allow change in unsupported parameters */
-	if (rxfh->key ||
-	    (rxfh->hfunc != ETH_RSS_HASH_NO_CHANGE &&
-	     rxfh->hfunc != ETH_RSS_HASH_TOP))
+	if (rxfh->hfunc != ETH_RSS_HASH_NO_CHANGE &&
+	    rxfh->hfunc != ETH_RSS_HASH_TOP)
 		return -EOPNOTSUPP;
-	if (!rxfh->indir)
-		return 0;
 
-	num_queues = adapter->rss_queues;
+	if (rxfh->indir) {
+		num_queues = adapter->rss_queues;
 
-	switch (hw->mac.type) {
-	case e1000_82576:
-		/* 82576 supports 2 RSS queues for SR-IOV */
-		if (adapter->vfs_allocated_count)
-			num_queues = 2;
-		break;
-	default:
-		break;
-	}
+		switch (hw->mac.type) {
+		case e1000_82576:
+			/* 82576 supports 2 RSS queues for SR-IOV */
+			if (adapter->vfs_allocated_count)
+				num_queues = 2;
+			break;
+		default:
+			break;
+		}
 
-	/* Verify user input. */
-	for (i = 0; i < IGB_RETA_SIZE; i++)
-		if (rxfh->indir[i] >= num_queues)
-			return -EINVAL;
+		/* Verify user input. */
+		for (i = 0; i < IGB_RETA_SIZE; i++)
+			if (rxfh->indir[i] >= num_queues)
+				return -EINVAL;
 
 
-	for (i = 0; i < IGB_RETA_SIZE; i++)
-		adapter->rss_indir_tbl[i] = rxfh->indir[i];
+		for (i = 0; i < IGB_RETA_SIZE; i++)
+			adapter->rss_indir_tbl[i] = rxfh->indir[i];
+
+		igb_write_rss_indir_tbl(adapter);
+	}
 
-	igb_write_rss_indir_tbl(adapter);
+	if (rxfh->key) {
+		memcpy(adapter->rss_key, rxfh->key, sizeof(adapter->rss_key));
+		igb_write_rss_key(adapter);
+	}
 
 	return 0;
 }
-- 
2.47.1

[PATCH net-next 07/11] igb: set skb hash type from RSS_TYPE

[Tony Nguyen]

From: Kohei Enju <kohei@enjuk.jp>

igb always marks the RX hash as L3 regardless of RSS_TYPE in the
advanced descriptor, which may indicate L4 (TCP/UDP) hash. This can
trigger unnecessary SW hash recalculation and breaks toeplitz selftests.

Use RSS_TYPE from pkt_info to set the correct PKT_HASH_TYPE_*

Tested by toeplitz.py with the igb RSS key get/set patches applied as
they are required for toeplitz.py (see Link below).
 # ethtool -N $DEV rx-flow-hash udp4 sdfn
 # ethtool -N $DEV rx-flow-hash udp6 sdfn
 # python toeplitz.py | grep -E "^# Totals"

Without patch:
 # Totals: pass:0 fail:12 xfail:0 xpass:0 skip:0 error:0

With patch:
 # Totals: pass:12 fail:0 xfail:0 xpass:0 skip:0 error:0

Link: https://lore.kernel.org/intel-wired-lan/20260119084511.95287-5-takkozu@amazon.com/
Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igb/e1000_82575.h | 21 ++++++++++++++++++++
 drivers/net/ethernet/intel/igb/igb_main.c    | 17 ++++++++++++----
 2 files changed, 34 insertions(+), 4 deletions(-)

diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.h b/drivers/net/ethernet/intel/igb/e1000_82575.h
index 63ec253ac788..9e696d55e512 100644
--- a/drivers/net/ethernet/intel/igb/e1000_82575.h
+++ b/drivers/net/ethernet/intel/igb/e1000_82575.h
@@ -87,6 +87,27 @@ union e1000_adv_rx_desc {
 	} wb;  /* writeback */
 };
 
+#define E1000_RSS_TYPE_NO_HASH		 0
+#define E1000_RSS_TYPE_HASH_TCP_IPV4	 1
+#define E1000_RSS_TYPE_HASH_IPV4	 2
+#define E1000_RSS_TYPE_HASH_TCP_IPV6	 3
+#define E1000_RSS_TYPE_HASH_IPV6_EX	 4
+#define E1000_RSS_TYPE_HASH_IPV6	 5
+#define E1000_RSS_TYPE_HASH_TCP_IPV6_EX	 6
+#define E1000_RSS_TYPE_HASH_UDP_IPV4	 7
+#define E1000_RSS_TYPE_HASH_UDP_IPV6	 8
+#define E1000_RSS_TYPE_HASH_UDP_IPV6_EX	 9
+
+#define E1000_RSS_TYPE_MASK		GENMASK(3, 0)
+
+#define E1000_RSS_L4_TYPES_MASK	\
+	(BIT(E1000_RSS_TYPE_HASH_TCP_IPV4)	| \
+	 BIT(E1000_RSS_TYPE_HASH_TCP_IPV6)	| \
+	 BIT(E1000_RSS_TYPE_HASH_TCP_IPV6_EX)	| \
+	 BIT(E1000_RSS_TYPE_HASH_UDP_IPV4)	| \
+	 BIT(E1000_RSS_TYPE_HASH_UDP_IPV6)	| \
+	 BIT(E1000_RSS_TYPE_HASH_UDP_IPV6_EX))
+
 #define E1000_RXDADV_HDRBUFLEN_MASK      0x7FE0
 #define E1000_RXDADV_HDRBUFLEN_SHIFT     5
 #define E1000_RXDADV_STAT_TS             0x10000 /* Pkt was time stamped */
diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c
index b7d36dd0b8e4..d4a897a8c82c 100644
--- a/drivers/net/ethernet/intel/igb/igb_main.c
+++ b/drivers/net/ethernet/intel/igb/igb_main.c
@@ -8820,10 +8820,19 @@ static inline void igb_rx_hash(struct igb_ring *ring,
 			       union e1000_adv_rx_desc *rx_desc,
 			       struct sk_buff *skb)
 {
-	if (ring->netdev->features & NETIF_F_RXHASH)
-		skb_set_hash(skb,
-			     le32_to_cpu(rx_desc->wb.lower.hi_dword.rss),
-			     PKT_HASH_TYPE_L3);
+	u16 rss_type;
+
+	if (!(ring->netdev->features & NETIF_F_RXHASH))
+		return;
+
+	rss_type = le16_to_cpu(rx_desc->wb.lower.lo_dword.pkt_info) &
+		   E1000_RSS_TYPE_MASK;
+	if (!rss_type)
+		return;
+
+	skb_set_hash(skb, le32_to_cpu(rx_desc->wb.lower.hi_dword.rss),
+		     (E1000_RSS_L4_TYPES_MASK & BIT(rss_type)) ?
+		     PKT_HASH_TYPE_L4 : PKT_HASH_TYPE_L3);
 }
 
 /**
-- 
2.47.1

[PATCH net-next 08/11] igc: remove unused autoneg_failed field

[Tony Nguyen]

From: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>

autoneg_failed in struct igc_mac_info is never set in the igc driver.
Remove the field and the dead code checking it in
igc_config_fc_after_link_up().

The field originates from the e1000/e1000e fiber/serdes forced-link
path, where MAC-level autoneg timeout sets it to signal the flow-control
code to force pause. igc supports only copper, so it never needs to set
this field.

Reviewed-by: Looi Hong Aun <hong.aun.looi@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Signed-off-by: Khai Wen Tan <khai.wen.tan@linux.intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Moriya Kadosh <moriyax.kadosh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igc/igc_hw.h  |  1 -
 drivers/net/ethernet/intel/igc/igc_mac.c | 16 +---------------
 2 files changed, 1 insertion(+), 16 deletions(-)

diff --git a/drivers/net/ethernet/intel/igc/igc_hw.h b/drivers/net/ethernet/intel/igc/igc_hw.h
index be8a49a86d09..86ab8f566f44 100644
--- a/drivers/net/ethernet/intel/igc/igc_hw.h
+++ b/drivers/net/ethernet/intel/igc/igc_hw.h
@@ -92,7 +92,6 @@ struct igc_mac_info {
 	bool asf_firmware_present;
 	bool arc_subsystem_valid;
 
-	bool autoneg_failed;
 	bool get_link_status;
 };
 
diff --git a/drivers/net/ethernet/intel/igc/igc_mac.c b/drivers/net/ethernet/intel/igc/igc_mac.c
index 7ac6637f8db7..142beb9ae557 100644
--- a/drivers/net/ethernet/intel/igc/igc_mac.c
+++ b/drivers/net/ethernet/intel/igc/igc_mac.c
@@ -438,28 +438,14 @@ void igc_config_collision_dist(struct igc_hw *hw)
  * Checks the status of auto-negotiation after link up to ensure that the
  * speed and duplex were not forced.  If the link needed to be forced, then
  * flow control needs to be forced also.  If auto-negotiation is enabled
- * and did not fail, then we configure flow control based on our link
- * partner.
+ * then we configure flow control based on our link partner.
  */
 s32 igc_config_fc_after_link_up(struct igc_hw *hw)
 {
 	u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
-	struct igc_mac_info *mac = &hw->mac;
 	u16 speed, duplex;
 	s32 ret_val = 0;
 
-	/* Check for the case where we have fiber media and auto-neg failed
-	 * so we had to force link.  In this case, we need to force the
-	 * configuration of the MAC to match the "fc" parameter.
-	 */
-	if (mac->autoneg_failed)
-		ret_val = igc_force_mac_fc(hw);
-
-	if (ret_val) {
-		hw_dbg("Error forcing flow control settings\n");
-		goto out;
-	}
-
 	/* In auto-neg, we need to check and see if Auto-Neg has completed,
 	 * and if so, how the PHY and link partner has flow control
 	 * configured.
-- 
2.47.1

[PATCH net-next 09/11] igc: move autoneg-enabled settings into igc_handle_autoneg_enabled()

[Tony Nguyen]

From: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>

Move the advertised link modes and flow control configuration from
igc_ethtool_set_link_ksettings() into igc_handle_autoneg_enabled().

No functional change.

Reviewed-by: Looi Hong Aun <hong.aun.looi@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Signed-off-by: Khai Wen Tan <khai.wen.tan@linux.intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Moriya Kadosh <moriyax.kadosh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igc/igc_ethtool.c | 72 ++++++++++++--------
 1 file changed, 44 insertions(+), 28 deletions(-)

diff --git a/drivers/net/ethernet/intel/igc/igc_ethtool.c b/drivers/net/ethernet/intel/igc/igc_ethtool.c
index fbba3e84673a..7ee84c24dc4e 100644
--- a/drivers/net/ethernet/intel/igc/igc_ethtool.c
+++ b/drivers/net/ethernet/intel/igc/igc_ethtool.c
@@ -2032,6 +2032,49 @@ static int igc_ethtool_get_link_ksettings(struct net_device *netdev,
 	return 0;
 }
 
+/**
+ * igc_handle_autoneg_enabled - Configure autonegotiation advertisement
+ * @adapter: private driver structure
+ * @cmd: ethtool link ksettings from user
+ *
+ * Records advertised speeds and flow control settings when autoneg
+ * is enabled.
+ */
+static void igc_handle_autoneg_enabled(struct igc_adapter *adapter,
+				       const struct ethtool_link_ksettings *cmd)
+{
+	struct igc_hw *hw = &adapter->hw;
+	u16 advertised = 0;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  2500baseT_Full))
+		advertised |= ADVERTISE_2500_FULL;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  1000baseT_Full))
+		advertised |= ADVERTISE_1000_FULL;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  100baseT_Full))
+		advertised |= ADVERTISE_100_FULL;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  100baseT_Half))
+		advertised |= ADVERTISE_100_HALF;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  10baseT_Full))
+		advertised |= ADVERTISE_10_FULL;
+
+	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
+						  10baseT_Half))
+		advertised |= ADVERTISE_10_HALF;
+
+	hw->phy.autoneg_advertised = advertised;
+	if (adapter->fc_autoneg)
+		hw->fc.requested_mode = igc_fc_default;
+}
+
 static int
 igc_ethtool_set_link_ksettings(struct net_device *netdev,
 			       const struct ethtool_link_ksettings *cmd)
@@ -2039,7 +2082,6 @@ igc_ethtool_set_link_ksettings(struct net_device *netdev,
 	struct igc_adapter *adapter = netdev_priv(netdev);
 	struct net_device *dev = adapter->netdev;
 	struct igc_hw *hw = &adapter->hw;
-	u16 advertised = 0;
 
 	/* When adapter in resetting mode, autoneg/speed/duplex
 	 * cannot be changed
@@ -2064,34 +2106,8 @@ igc_ethtool_set_link_ksettings(struct net_device *netdev,
 	while (test_and_set_bit(__IGC_RESETTING, &adapter->state))
 		usleep_range(1000, 2000);
 
-	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
-						  2500baseT_Full))
-		advertised |= ADVERTISE_2500_FULL;
-
-	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
-						  1000baseT_Full))
-		advertised |= ADVERTISE_1000_FULL;
-
-	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
-						  100baseT_Full))
-		advertised |= ADVERTISE_100_FULL;
-
-	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
-						  100baseT_Half))
-		advertised |= ADVERTISE_100_HALF;
-
-	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
-						  10baseT_Full))
-		advertised |= ADVERTISE_10_FULL;
-
-	if (ethtool_link_ksettings_test_link_mode(cmd, advertising,
-						  10baseT_Half))
-		advertised |= ADVERTISE_10_HALF;
-
 	if (cmd->base.autoneg == AUTONEG_ENABLE) {
-		hw->phy.autoneg_advertised = advertised;
-		if (adapter->fc_autoneg)
-			hw->fc.requested_mode = igc_fc_default;
+		igc_handle_autoneg_enabled(adapter, cmd);
 	} else {
 		netdev_info(dev, "Force mode currently not supported\n");
 	}
-- 
2.47.1

[PATCH net-next 10/11] igc: replace goto out with direct returns in igc_config_fc_after_link_up()

[Tony Nguyen]

From: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>

The out: label only returns ret_val with no cleanup. The kernel coding
style guide states: "If there is no cleanup needed then just return
directly." (Documentation/process/coding-style.rst, section 7).

This improves readability ahead of a subsequent patch that introduces a
new goto label in this function.

No functional change.

Reviewed-by: Looi Hong Aun <hong.aun.looi@intel.com>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Signed-off-by: Khai Wen Tan <khai.wen.tan@linux.intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Moriya Kadosh <moriyax.kadosh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igc/igc_mac.c | 15 +++++++--------
 1 file changed, 7 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/intel/igc/igc_mac.c b/drivers/net/ethernet/intel/igc/igc_mac.c
index 142beb9ae557..0a3d3f357505 100644
--- a/drivers/net/ethernet/intel/igc/igc_mac.c
+++ b/drivers/net/ethernet/intel/igc/igc_mac.c
@@ -458,15 +458,15 @@ s32 igc_config_fc_after_link_up(struct igc_hw *hw)
 	ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS,
 				       &mii_status_reg);
 	if (ret_val)
-		goto out;
+		return ret_val;
 	ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS,
 				       &mii_status_reg);
 	if (ret_val)
-		goto out;
+		return ret_val;
 
 	if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) {
 		hw_dbg("Copper PHY and Auto Neg has not completed.\n");
-		goto out;
+		return ret_val;
 	}
 
 	/* The AutoNeg process has completed, so we now need to
@@ -478,11 +478,11 @@ s32 igc_config_fc_after_link_up(struct igc_hw *hw)
 	ret_val = hw->phy.ops.read_reg(hw, PHY_AUTONEG_ADV,
 				       &mii_nway_adv_reg);
 	if (ret_val)
-		goto out;
+		return ret_val;
 	ret_val = hw->phy.ops.read_reg(hw, PHY_LP_ABILITY,
 				       &mii_nway_lp_ability_reg);
 	if (ret_val)
-		goto out;
+		return ret_val;
 	/* Two bits in the Auto Negotiation Advertisement Register
 	 * (Address 4) and two bits in the Auto Negotiation Base
 	 * Page Ability Register (Address 5) determine flow control
@@ -598,7 +598,7 @@ s32 igc_config_fc_after_link_up(struct igc_hw *hw)
 	ret_val = hw->mac.ops.get_speed_and_duplex(hw, &speed, &duplex);
 	if (ret_val) {
 		hw_dbg("Error getting link speed and duplex\n");
-		goto out;
+		return ret_val;
 	}
 
 	if (duplex == HALF_DUPLEX)
@@ -610,10 +610,9 @@ s32 igc_config_fc_after_link_up(struct igc_hw *hw)
 	ret_val = igc_force_mac_fc(hw);
 	if (ret_val) {
 		hw_dbg("Error forcing flow control settings\n");
-		goto out;
+		return ret_val;
 	}
 
-out:
 	return ret_val;
 }
 
-- 
2.47.1

[PATCH net-next 11/11] igc: add support for forcing link speed without autonegotiation

[Tony Nguyen]

From: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>

Allow users to force 10/100 Mb/s link speed and duplex via ethtool
when autonegotiation is disabled. Previously, the driver rejected
these requests with "Force mode currently not supported.".

Forcing at 1000 Mb/s and 2500 Mb/s is not supported.

Reviewed-by: Looi Hong Aun <hong.aun.looi@intel.com>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Signed-off-by: Khai Wen Tan <khai.wen.tan@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Moriya Kadosh <moriyax.kadosh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
---
 drivers/net/ethernet/intel/igc/igc_base.c    |  35 ++++-
 drivers/net/ethernet/intel/igc/igc_defines.h |   9 +-
 drivers/net/ethernet/intel/igc/igc_ethtool.c | 138 ++++++++++++++-----
 drivers/net/ethernet/intel/igc/igc_hw.h      |   9 ++
 drivers/net/ethernet/intel/igc/igc_mac.c     |  12 ++
 drivers/net/ethernet/intel/igc/igc_main.c    |   2 +-
 drivers/net/ethernet/intel/igc/igc_phy.c     |  65 ++++++++-
 drivers/net/ethernet/intel/igc/igc_phy.h     |   1 +
 8 files changed, 220 insertions(+), 51 deletions(-)

diff --git a/drivers/net/ethernet/intel/igc/igc_base.c b/drivers/net/ethernet/intel/igc/igc_base.c
index 1613b562d17c..ab9120a3127f 100644
--- a/drivers/net/ethernet/intel/igc/igc_base.c
+++ b/drivers/net/ethernet/intel/igc/igc_base.c
@@ -114,11 +114,35 @@ static s32 igc_setup_copper_link_base(struct igc_hw *hw)
 	u32 ctrl;
 
 	ctrl = rd32(IGC_CTRL);
-	ctrl |= IGC_CTRL_SLU;
-	ctrl &= ~(IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX);
-	wr32(IGC_CTRL, ctrl);
-
-	ret_val = igc_setup_copper_link(hw);
+	ctrl &= ~(IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX |
+		  IGC_CTRL_SPEED_MASK | IGC_CTRL_FD);
+
+	if (hw->mac.autoneg_enabled) {
+		ctrl |= IGC_CTRL_SLU;
+		wr32(IGC_CTRL, ctrl);
+		ret_val = igc_setup_copper_link(hw);
+	} else {
+		ctrl |= IGC_CTRL_SLU | IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX;
+
+		switch (hw->mac.forced_speed_duplex) {
+		case IGC_FORCED_10H:
+			ctrl |= IGC_CTRL_SPEED_10;
+			break;
+		case IGC_FORCED_10F:
+			ctrl |= IGC_CTRL_SPEED_10 | IGC_CTRL_FD;
+			break;
+		case IGC_FORCED_100H:
+			ctrl |= IGC_CTRL_SPEED_100;
+			break;
+		case IGC_FORCED_100F:
+			ctrl |= IGC_CTRL_SPEED_100 | IGC_CTRL_FD;
+			break;
+		default:
+			return -IGC_ERR_CONFIG;
+		}
+		wr32(IGC_CTRL, ctrl);
+		ret_val = igc_setup_copper_link(hw);
+	}
 
 	return ret_val;
 }
@@ -443,6 +467,7 @@ static const struct igc_phy_operations igc_phy_ops_base = {
 	.reset			= igc_phy_hw_reset,
 	.read_reg		= igc_read_phy_reg_gpy,
 	.write_reg		= igc_write_phy_reg_gpy,
+	.force_speed_duplex	= igc_force_speed_duplex,
 };
 
 const struct igc_info igc_base_info = {
diff --git a/drivers/net/ethernet/intel/igc/igc_defines.h b/drivers/net/ethernet/intel/igc/igc_defines.h
index 9482ab11f050..3f504751c2d9 100644
--- a/drivers/net/ethernet/intel/igc/igc_defines.h
+++ b/drivers/net/ethernet/intel/igc/igc_defines.h
@@ -129,10 +129,13 @@
 #define IGC_ERR_SWFW_SYNC		13
 
 /* Device Control */
+#define IGC_CTRL_FD		BIT(0)  /* Full Duplex */
 #define IGC_CTRL_RST		0x04000000  /* Global reset */
-
 #define IGC_CTRL_PHY_RST	0x80000000  /* PHY Reset */
 #define IGC_CTRL_SLU		0x00000040  /* Set link up (Force Link) */
+#define IGC_CTRL_SPEED_MASK	GENMASK(10, 8)
+#define IGC_CTRL_SPEED_10	FIELD_PREP(IGC_CTRL_SPEED_MASK, 0)
+#define IGC_CTRL_SPEED_100	FIELD_PREP(IGC_CTRL_SPEED_MASK, 1)
 #define IGC_CTRL_FRCSPD		0x00000800  /* Force Speed */
 #define IGC_CTRL_FRCDPX		0x00001000  /* Force Duplex */
 #define IGC_CTRL_VME		0x40000000  /* IEEE VLAN mode enable */
@@ -673,6 +676,10 @@
 #define IGC_GEN_POLL_TIMEOUT	1920
 
 /* PHY Control Register */
+#define MII_CR_SPEED_MASK	(BIT(6) | BIT(13))
+#define MII_CR_SPEED_10		0x0000	/* SSM=0, SSL=0: 10 Mb/s */
+#define MII_CR_SPEED_100	BIT(13)	/* SSM=0, SSL=1: 100 Mb/s */
+#define MII_CR_DUPLEX_EN	BIT(8)	/* 0 = Half Duplex, 1 = Full Duplex */
 #define MII_CR_RESTART_AUTO_NEG	0x0200  /* Restart auto negotiation */
 #define MII_CR_POWER_DOWN	0x0800  /* Power down */
 #define MII_CR_AUTO_NEG_EN	0x1000  /* Auto Neg Enable */
diff --git a/drivers/net/ethernet/intel/igc/igc_ethtool.c b/drivers/net/ethernet/intel/igc/igc_ethtool.c
index 7ee84c24dc4e..89fe2788a565 100644
--- a/drivers/net/ethernet/intel/igc/igc_ethtool.c
+++ b/drivers/net/ethernet/intel/igc/igc_ethtool.c
@@ -1946,44 +1946,58 @@ static int igc_ethtool_get_link_ksettings(struct net_device *netdev,
 	ethtool_link_ksettings_add_link_mode(cmd, supported, TP);
 	ethtool_link_ksettings_add_link_mode(cmd, advertising, TP);
 
-	/* advertising link modes */
-	if (hw->phy.autoneg_advertised & ADVERTISE_10_HALF)
-		ethtool_link_ksettings_add_link_mode(cmd, advertising, 10baseT_Half);
-	if (hw->phy.autoneg_advertised & ADVERTISE_10_FULL)
-		ethtool_link_ksettings_add_link_mode(cmd, advertising, 10baseT_Full);
-	if (hw->phy.autoneg_advertised & ADVERTISE_100_HALF)
-		ethtool_link_ksettings_add_link_mode(cmd, advertising, 100baseT_Half);
-	if (hw->phy.autoneg_advertised & ADVERTISE_100_FULL)
-		ethtool_link_ksettings_add_link_mode(cmd, advertising, 100baseT_Full);
-	if (hw->phy.autoneg_advertised & ADVERTISE_1000_FULL)
-		ethtool_link_ksettings_add_link_mode(cmd, advertising, 1000baseT_Full);
-	if (hw->phy.autoneg_advertised & ADVERTISE_2500_FULL)
-		ethtool_link_ksettings_add_link_mode(cmd, advertising, 2500baseT_Full);
-
 	/* set autoneg settings */
 	ethtool_link_ksettings_add_link_mode(cmd, supported, Autoneg);
-	ethtool_link_ksettings_add_link_mode(cmd, advertising, Autoneg);
+	if (hw->mac.autoneg_enabled) {
+		ethtool_link_ksettings_add_link_mode(cmd, advertising, Autoneg);
+		cmd->base.autoneg = AUTONEG_ENABLE;
+
+		/* advertising link modes only apply when autoneg is on */
+		if (hw->phy.autoneg_advertised & ADVERTISE_10_HALF)
+			ethtool_link_ksettings_add_link_mode(cmd, advertising,
+							     10baseT_Half);
+		if (hw->phy.autoneg_advertised & ADVERTISE_10_FULL)
+			ethtool_link_ksettings_add_link_mode(cmd, advertising,
+							     10baseT_Full);
+		if (hw->phy.autoneg_advertised & ADVERTISE_100_HALF)
+			ethtool_link_ksettings_add_link_mode(cmd, advertising,
+							     100baseT_Half);
+		if (hw->phy.autoneg_advertised & ADVERTISE_100_FULL)
+			ethtool_link_ksettings_add_link_mode(cmd, advertising,
+							     100baseT_Full);
+		if (hw->phy.autoneg_advertised & ADVERTISE_1000_FULL)
+			ethtool_link_ksettings_add_link_mode(cmd, advertising,
+							     1000baseT_Full);
+		if (hw->phy.autoneg_advertised & ADVERTISE_2500_FULL)
+			ethtool_link_ksettings_add_link_mode(cmd, advertising,
+							     2500baseT_Full);
+
+		/* Set pause flow control advertising */
+		switch (hw->fc.requested_mode) {
+		case igc_fc_full:
+			ethtool_link_ksettings_add_link_mode(cmd, advertising,
+							     Pause);
+			break;
+		case igc_fc_rx_pause:
+			ethtool_link_ksettings_add_link_mode(cmd, advertising,
+							     Pause);
+			ethtool_link_ksettings_add_link_mode(cmd, advertising,
+							     Asym_Pause);
+			break;
+		case igc_fc_tx_pause:
+			ethtool_link_ksettings_add_link_mode(cmd, advertising,
+							     Asym_Pause);
+			break;
+		default:
+			break;
+		}
+	} else {
+		cmd->base.autoneg = AUTONEG_DISABLE;
+	}
 
-	/* Set pause flow control settings */
+	/* Pause is always supported */
 	ethtool_link_ksettings_add_link_mode(cmd, supported, Pause);
 
-	switch (hw->fc.requested_mode) {
-	case igc_fc_full:
-		ethtool_link_ksettings_add_link_mode(cmd, advertising, Pause);
-		break;
-	case igc_fc_rx_pause:
-		ethtool_link_ksettings_add_link_mode(cmd, advertising, Pause);
-		ethtool_link_ksettings_add_link_mode(cmd, advertising,
-						     Asym_Pause);
-		break;
-	case igc_fc_tx_pause:
-		ethtool_link_ksettings_add_link_mode(cmd, advertising,
-						     Asym_Pause);
-		break;
-	default:
-		break;
-	}
-
 	status = pm_runtime_suspended(&adapter->pdev->dev) ?
 		 0 : rd32(IGC_STATUS);
 
@@ -2015,7 +2029,6 @@ static int igc_ethtool_get_link_ksettings(struct net_device *netdev,
 		cmd->base.duplex = DUPLEX_UNKNOWN;
 	}
 	cmd->base.speed = speed;
-	cmd->base.autoneg = AUTONEG_ENABLE;
 
 	/* MDI-X => 2; MDI =>1; Invalid =>0 */
 	if (hw->phy.media_type == igc_media_type_copper)
@@ -2032,6 +2045,37 @@ static int igc_ethtool_get_link_ksettings(struct net_device *netdev,
 	return 0;
 }
 
+/**
+ * igc_handle_autoneg_disabled - Configure forced speed/duplex settings
+ * @adapter: private driver structure
+ * @speed: requested speed (must be SPEED_10 or SPEED_100)
+ * @duplex: requested duplex
+ *
+ * Records forced speed/duplex when autoneg is disabled.
+ * Caller must validate speed before calling this function.
+ */
+static void igc_handle_autoneg_disabled(struct igc_adapter *adapter, u32 speed,
+					u8 duplex)
+{
+	struct igc_mac_info *mac = &adapter->hw.mac;
+
+	switch (speed) {
+	case SPEED_10:
+		mac->forced_speed_duplex = (duplex == DUPLEX_FULL) ?
+			IGC_FORCED_10F : IGC_FORCED_10H;
+		break;
+	case SPEED_100:
+		mac->forced_speed_duplex = (duplex == DUPLEX_FULL) ?
+			IGC_FORCED_100F : IGC_FORCED_100H;
+		break;
+	default:
+		WARN_ONCE(1, "Unsupported speed %u\n", speed);
+		return;
+	}
+
+	mac->autoneg_enabled = false;
+}
+
 /**
  * igc_handle_autoneg_enabled - Configure autonegotiation advertisement
  * @adapter: private driver structure
@@ -2070,6 +2114,7 @@ static void igc_handle_autoneg_enabled(struct igc_adapter *adapter,
 						  10baseT_Half))
 		advertised |= ADVERTISE_10_HALF;
 
+	hw->mac.autoneg_enabled = true;
 	hw->phy.autoneg_advertised = advertised;
 	if (adapter->fc_autoneg)
 		hw->fc.requested_mode = igc_fc_default;
@@ -2091,6 +2136,12 @@ igc_ethtool_set_link_ksettings(struct net_device *netdev,
 		return -EINVAL;
 	}
 
+	if (cmd->base.autoneg != AUTONEG_ENABLE &&
+	    cmd->base.autoneg != AUTONEG_DISABLE) {
+		netdev_info(dev, "Unsupported autoneg setting\n");
+		return -EINVAL;
+	}
+
 	/* MDI setting is only allowed when autoneg enabled because
 	 * some hardware doesn't allow MDI setting when speed or
 	 * duplex is forced.
@@ -2103,14 +2154,25 @@ igc_ethtool_set_link_ksettings(struct net_device *netdev,
 		}
 	}
 
+	if (cmd->base.autoneg == AUTONEG_DISABLE) {
+		if (cmd->base.speed != SPEED_10 && cmd->base.speed != SPEED_100) {
+			netdev_info(dev, "Unsupported speed for forced link\n");
+			return -EINVAL;
+		}
+		if (cmd->base.duplex != DUPLEX_HALF && cmd->base.duplex != DUPLEX_FULL) {
+			netdev_info(dev, "Duplex must be half or full for forced link\n");
+			return -EINVAL;
+		}
+	}
+
 	while (test_and_set_bit(__IGC_RESETTING, &adapter->state))
 		usleep_range(1000, 2000);
 
-	if (cmd->base.autoneg == AUTONEG_ENABLE) {
+	if (cmd->base.autoneg == AUTONEG_ENABLE)
 		igc_handle_autoneg_enabled(adapter, cmd);
-	} else {
-		netdev_info(dev, "Force mode currently not supported\n");
-	}
+	else
+		igc_handle_autoneg_disabled(adapter, cmd->base.speed,
+					    cmd->base.duplex);
 
 	/* MDI-X => 2; MDI => 1; Auto => 3 */
 	if (cmd->base.eth_tp_mdix_ctrl) {
diff --git a/drivers/net/ethernet/intel/igc/igc_hw.h b/drivers/net/ethernet/intel/igc/igc_hw.h
index 86ab8f566f44..62aaee55668a 100644
--- a/drivers/net/ethernet/intel/igc/igc_hw.h
+++ b/drivers/net/ethernet/intel/igc/igc_hw.h
@@ -73,6 +73,13 @@ struct igc_info {
 
 extern const struct igc_info igc_base_info;
 
+enum igc_forced_speed_duplex {
+	IGC_FORCED_10H,
+	IGC_FORCED_10F,
+	IGC_FORCED_100H,
+	IGC_FORCED_100F,
+};
+
 struct igc_mac_info {
 	struct igc_mac_operations ops;
 
@@ -93,6 +100,8 @@ struct igc_mac_info {
 	bool arc_subsystem_valid;
 
 	bool get_link_status;
+	bool autoneg_enabled;
+	enum igc_forced_speed_duplex forced_speed_duplex;
 };
 
 struct igc_nvm_operations {
diff --git a/drivers/net/ethernet/intel/igc/igc_mac.c b/drivers/net/ethernet/intel/igc/igc_mac.c
index 0a3d3f357505..d6f3f6618469 100644
--- a/drivers/net/ethernet/intel/igc/igc_mac.c
+++ b/drivers/net/ethernet/intel/igc/igc_mac.c
@@ -446,6 +446,17 @@ s32 igc_config_fc_after_link_up(struct igc_hw *hw)
 	u16 speed, duplex;
 	s32 ret_val = 0;
 
+	/* Without autoneg, flow control capability is not exchanged with the
+	 * link partner. IEEE 802.3 prohibits flow control in half-duplex mode.
+	 */
+	if (!hw->mac.autoneg_enabled) {
+		if (hw->mac.forced_speed_duplex == IGC_FORCED_10H ||
+		    hw->mac.forced_speed_duplex == IGC_FORCED_100H)
+			hw->fc.current_mode = igc_fc_none;
+
+		goto force_fc;
+	}
+
 	/* In auto-neg, we need to check and see if Auto-Neg has completed,
 	 * and if so, how the PHY and link partner has flow control
 	 * configured.
@@ -607,6 +618,7 @@ s32 igc_config_fc_after_link_up(struct igc_hw *hw)
 	/* Now we call a subroutine to actually force the MAC
 	 * controller to use the correct flow control settings.
 	 */
+force_fc:
 	ret_val = igc_force_mac_fc(hw);
 	if (ret_val) {
 		hw_dbg("Error forcing flow control settings\n");
diff --git a/drivers/net/ethernet/intel/igc/igc_main.c b/drivers/net/ethernet/intel/igc/igc_main.c
index 5ef229a5931f..e6e9441fc3d4 100644
--- a/drivers/net/ethernet/intel/igc/igc_main.c
+++ b/drivers/net/ethernet/intel/igc/igc_main.c
@@ -7298,7 +7298,7 @@ static int igc_probe(struct pci_dev *pdev,
 	/* Initialize link properties that are user-changeable */
 	adapter->fc_autoneg = true;
 	hw->phy.autoneg_advertised = 0xaf;
-
+	hw->mac.autoneg_enabled = true;
 	hw->fc.requested_mode = igc_fc_default;
 	hw->fc.current_mode = igc_fc_default;
 
diff --git a/drivers/net/ethernet/intel/igc/igc_phy.c b/drivers/net/ethernet/intel/igc/igc_phy.c
index 6c4d204aecfa..4cf737fb3b21 100644
--- a/drivers/net/ethernet/intel/igc/igc_phy.c
+++ b/drivers/net/ethernet/intel/igc/igc_phy.c
@@ -494,12 +494,20 @@ s32 igc_setup_copper_link(struct igc_hw *hw)
 	s32 ret_val = 0;
 	bool link;
 
-	/* Setup autoneg and flow control advertisement and perform
-	 * autonegotiation.
-	 */
-	ret_val = igc_copper_link_autoneg(hw);
-	if (ret_val)
-		goto out;
+	if (hw->mac.autoneg_enabled) {
+		/* Setup autoneg and flow control advertisement and perform
+		 * autonegotiation.
+		 */
+		ret_val = igc_copper_link_autoneg(hw);
+		if (ret_val)
+			goto out;
+	} else {
+		ret_val = hw->phy.ops.force_speed_duplex(hw);
+		if (ret_val) {
+			hw_dbg("Error Forcing Speed/Duplex\n");
+			goto out;
+		}
+	}
 
 	/* Check link status. Wait up to 100 microseconds for link to become
 	 * valid.
@@ -778,3 +786,48 @@ u16 igc_read_phy_fw_version(struct igc_hw *hw)
 
 	return gphy_version;
 }
+
+/**
+ * igc_force_speed_duplex - Force PHY speed and duplex settings
+ * @hw: pointer to the HW structure
+ *
+ * Programs the GPY PHY control register to disable autonegotiation
+ * and force the speed/duplex indicated by hw->mac.forced_speed_duplex.
+ */
+s32 igc_force_speed_duplex(struct igc_hw *hw)
+{
+	struct igc_phy_info *phy = &hw->phy;
+	u16 phy_ctrl;
+	s32 ret_val;
+
+	ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_ctrl);
+	if (ret_val)
+		return ret_val;
+
+	phy_ctrl &= ~(MII_CR_SPEED_MASK | MII_CR_DUPLEX_EN |
+		      MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+
+	switch (hw->mac.forced_speed_duplex) {
+	case IGC_FORCED_10H:
+		phy_ctrl |= MII_CR_SPEED_10;
+		break;
+	case IGC_FORCED_10F:
+		phy_ctrl |= MII_CR_SPEED_10 | MII_CR_DUPLEX_EN;
+		break;
+	case IGC_FORCED_100H:
+		phy_ctrl |= MII_CR_SPEED_100;
+		break;
+	case IGC_FORCED_100F:
+		phy_ctrl |= MII_CR_SPEED_100 | MII_CR_DUPLEX_EN;
+		break;
+	default:
+		return -IGC_ERR_CONFIG;
+	}
+
+	ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_ctrl);
+	if (ret_val)
+		return ret_val;
+
+	hw->mac.get_link_status = true;
+	return 0;
+}
diff --git a/drivers/net/ethernet/intel/igc/igc_phy.h b/drivers/net/ethernet/intel/igc/igc_phy.h
index 832a7e359f18..d37a89174826 100644
--- a/drivers/net/ethernet/intel/igc/igc_phy.h
+++ b/drivers/net/ethernet/intel/igc/igc_phy.h
@@ -18,5 +18,6 @@ void igc_power_down_phy_copper(struct igc_hw *hw);
 s32 igc_write_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 data);
 s32 igc_read_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 *data);
 u16 igc_read_phy_fw_version(struct igc_hw *hw);
+s32 igc_force_speed_duplex(struct igc_hw *hw);
 
 #endif
-- 
2.47.1