From: Christian Heimanns <heimanns@versanet.de>
To: linux-smp@vger.kernel.org
Subject: unexpected IO-APIC
Date: Tue, 17 Dec 2002 15:46:59 +0100 [thread overview]
Message-ID: <20021217154659.6e70e560.heimanns@versanet.de> (raw)
[-- Attachment #1: Type: text/plain, Size: 766 bytes --]
Hello kernel developers,
I'm the owner of a new mainboard:
MSI KT4L (MS-6712) with the new KT400 chipset. The CPU is a AMD Athlon
XP 2400+, assited by 512MB DDR-RAM (2700).
The Linux-Distribution I use is SuSE-8.1 with SuSE-kernel (uname -r)
2.4.19-4GB.
In the boot message (dmesg) I saw the request to give you a note.
Attached you will find the boot message (dmesg.txt).
With APIC disabled and ACPI=off everything is fine, but with APIC
enabled and ACPI=off I have some problems with my grafic adapter and
setterm -blank x. After blanking using APM and trying to wake up the
computer it freeze.
With regards,
--
Christian Heimanns (Germany)
heimanns@versanet.de
### Pinguine können nicht fliegen
- Pinguine stürzen auch nicht ab! ###
[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 14542 bytes --]
Linux version 2.4.19-4GB (root@Athlon.suse.de) (gcc version 3.2) #1 Wed Nov 27 00:56:53 UTC 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
found SMP MP-table at 000fb930
hm, page 000fb000 reserved twice.
hm, page 000fc000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
Advanced speculative caching feature present
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: VIA Product ID: VT5440B APIC at: 0xFEE00000
Processor #0 6:8 APIC version 17
I/O APIC #2 Version 3 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Building zonelist for node : 0
Kernel command line: apic root=/dev/hda7 acpi=off hdc=ide-scsi hdd=ide-scsi max_scsi_luns=1 vga=794 init 3
ide_setup: hdc=ide-scsi
ide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 2030.129 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 4050.12 BogoMIPS
Memory: 513900k/524224k available (1688k kernel code, 9936k reserved, 569k data, 168k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383fbff c1c3fbff 00000000, vendor = 2
Advanced speculative caching feature present
Disabling advanced speculative caching
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbf7 c1c3fbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbf7 c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbf7 c1c3fbff 00000000 00000000
CPU: AMD Athlon(tm) XP 2400+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000080
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-12, 2-18, 2-19, 2-20, 2-22 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 20.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 51
07 001 01 0 0 0 0 0 1 1 59
08 001 01 0 0 0 0 0 1 1 61
09 001 01 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 001 01 0 0 0 0 0 1 1 71
0e 001 01 0 0 0 0 0 1 1 79
0f 001 01 0 0 0 0 0 1 1 81
10 001 01 1 1 0 1 0 1 1 89
11 001 01 1 1 0 1 0 1 1 91
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 001 01 1 1 0 1 0 1 1 99
16 000 00 1 0 0 0 0 0 0 00
17 001 01 1 1 0 1 0 1 1 A1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ21 -> 0:21
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2030.2271 MHz.
..... host bus clock speed is 270.6968 MHz.
cpu: 0, clocks: 2706968, slice: 1353484
CPU0<T0:2706960,T1:1353472,D:4,S:1353484,C:2706968>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20020829
ACPI: Disabled via blacklist or command line
PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router default [1106/3177] at 00:11.0
PCI->APIC IRQ transform: (B0,I6,P0) -> 17
PCI->APIC IRQ transform: (B0,I16,P0) -> 21
PCI->APIC IRQ transform: (B0,I16,P1) -> 21
PCI->APIC IRQ transform: (B0,I16,P2) -> 21
PCI->APIC IRQ transform: (B0,I16,P3) -> 21
PCI->APIC IRQ transform: (B0,I17,P0) -> 16
PCI->APIC IRQ transform: (B0,I18,P0) -> 23
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI: Via IRQ fixup for 00:10.1, from 10 to 5
PCI: Via IRQ fixup for 00:10.0, from 11 to 5
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
bigpage subsystem: allocated 0 bigpages (=0MB).
kinoded started
VFS: Diskquotas version dquot_6.5.0 initialized
aio_setup: num_physpages = 32764
aio_setup: sizeof(struct page) = 48
vesafb: framebuffer at 0xd0000000, mapped to 0xe080d000, size 65536k
vesafb: mode is 1280x1024x16, linelength=2560, pages=1
vesafb: protected mode interface info at c000:e9d0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture.... found (1280x1024, 38795 bytes).
Console: switching to colour frame buffer device 132x45
fb0: VESA VGA frame buffer device
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 89
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: IC35L080AVVA07-0, ATA DISK drive
hdc: TOSHIBA DVD-ROM SD-M1712, ATAPI CD/DVD-ROM drive
hdd: PLEXTOR CD-R PX-W4012A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c03c9484, I/O limit 4095Mb (mask 0xffffffff)
hda: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=10011/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 16 devices)
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
ide-floppy driver 0.99.newide
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 264k freed
VFS: Mounted root (ext2 filesystem).
scsi: limiting sg entries to 204
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-M1712 Rev: 1004
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PLEXTOR Model: CD-R PX-W4012A Rev: 1.03
Type: CD-ROM ANSI SCSI revision: 02
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (ide0(3,7)) for (ide0(3,7))
reiserfs: using ordered data mode
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 168k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding Swap: 658624k swap-space (priority 42)
MSDOS FS: IO charset iso8859-15
via-rhine.c:v1.10-LK1.1.14 May-3-2002 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
eth0: VIA VT6102 Rhine-II at 0xcc00, 00:10:dc:c0:6d:58, IRQ 23.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 45e1.
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
hcd.c: ehci-hcd @ 00:10.3, VIA Technologies, Inc. USB 2.0
hcd.c: irq 21, pci mem e4918f00
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0
hub.c: USB hub found
hub.c: 6 ports detected
usb-uhci.c: $Revision: 1.275 $ time 01:48:07 Nov 27 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
uhci.c: USB Universal Host Controller Interface driver v1.1
hub.c: USB new device connect on bus3/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x46d/0xc00e) is not claimed by any active driver.
hub.c: USB new device connect on bus3/2, assigned device number 3
usb.c: USB device 3 (vend/prod 0x4b8/0x5) is not claimed by any active driver.
sg_attach: dev0=(21:0)
sg_attach: dev1=(21:1)
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
mice: PS/2 mouse device common for all mice
usb.c: registered new driver hiddev
usb.c: registered new driver hid
input0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb3:2.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
usb.c: registered new driver usblp
printer.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
printer.c: v0.11: USB Printer Device Class driver
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
cdrom: open failed.
cdrom: open failed.
ide-scsi: hdd: unsupported command in request queue (0)
end_request: I/O error, dev 16:40 (hdd), sector 64
ide-scsi: hdd: unsupported command in request queue (0)
end_request: I/O error, dev 16:40 (hdd), sector 66
ide-scsi: hdd: unsupported command in request queue (0)
end_request: I/O error, dev 16:40 (hdd), sector 68
ide-scsi: hdd: unsupported command in request queue (0)
end_request: I/O error, dev 16:40 (hdd), sector 70
ide-scsi: hdd: unsupported command in request queue (0)
end_request: I/O error, dev 16:40 (hdd), sector 72
ide-scsi: hdd: unsupported command in request queue (0)
end_request: I/O error, dev 16:40 (hdd), sector 74
ide-scsi: hdd: unsupported command in request queue (0)
end_request: I/O error, dev 16:40 (hdd), sector 76
ide-scsi: hdd: unsupported command in request queue (0)
end_request: I/O error, dev 16:40 (hdd), sector 78
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 64
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 66
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 68
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 70
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 72
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 74
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 76
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 78
cdrom: open failed.
next reply other threads:[~2002-12-17 14:46 UTC|newest]
Thread overview: 135+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-12-17 14:46 Christian Heimanns [this message]
-- strict thread matches above, loose matches on Subject: below --
2006-07-06 20:37 unexpected IO-APIC Danielle Hines
2006-07-07 13:12 ` Erik Mouw
2006-03-07 4:19 Mimi Zhou
2005-07-12 13:56 Unexpected IO-APIC Bill Baker
2005-07-12 16:42 ` randy_dunlap
2005-06-18 5:04 unexpected IO-APIC darshan
2005-05-26 8:44 Bernd Strebel
2005-05-27 5:33 ` randy_dunlap
2005-05-27 9:26 ` Bernd Strebel
2005-05-27 17:30 ` randy_dunlap
2005-05-27 22:24 ` Bernd Strebel
2005-05-30 22:43 ` randy_dunlap
2005-03-14 20:48 Unexpected IO-APIC Iuri Wickert
2005-03-15 20:32 ` Randy.Dunlap
2005-03-05 21:48 Marco van Beek
2005-03-15 20:23 ` Randy.Dunlap
2005-02-28 23:34 unexpected IO-APIC Mike Farnam
2005-03-15 17:48 ` Randy.Dunlap
2005-03-15 20:14 ` Randy.Dunlap
2005-01-31 17:41 Gary Buckmaster
2005-01-25 18:23 Unexpected IO-APIC Martin Slovacek
2005-01-25 18:59 ` Earle Nietzel
2004-12-28 6:58 unexpected IO-APIC Paul
2004-12-06 4:23 unexpected io-apic Simon Story
2004-07-23 20:33 unexpected IO-APIC Thomas Schlag
2004-07-08 7:52 S.K.Goel
2004-06-23 11:44 Jörg Lübbert
2004-06-23 11:42 Jörg Lübbert
2004-06-18 18:15 Unexpected IO-APIC GIN (Garreth Jeremiah)
2004-04-23 8:28 unexpected IO-APIC Piers Lauder
2004-04-18 17:53 dpn22
2004-04-07 8:11 JKolk
2004-04-01 14:32 Ian Jenkinson
2004-02-24 15:07 Unexpected IO-APIC Lyle Worthington
2004-02-24 16:38 ` Randy.Dunlap
2004-02-24 18:03 ` Lyle Worthington
2004-02-24 18:31 ` Randy.Dunlap
2004-02-15 8:24 unexpected IO-APIC Massa Takeuti
2004-01-16 3:40 Polyhead
2004-01-11 8:53 Russ McCallister
2003-12-18 7:21 Matthew Blakley
2003-12-13 5:50 Sterling Chavis
2003-11-23 6:38 W M Brelsford
2003-11-20 3:09 Chris Johns
2003-11-12 21:16 A.J. Duijn
2003-10-16 17:44 Lance Davis
2003-09-25 15:09 Unexpected IO-APIC David van Hoose
2003-09-11 16:36 unexpected IO-APIC John Birck
2003-09-04 16:37 Michael Sorrentino
2003-09-04 19:35 ` Alan Cox
2003-09-04 4:19 Unexpected IO-APIC Jeremy Sylvestre
2003-09-01 12:31 Alfonso Abeger
2003-08-21 7:51 Grage, Sascha
2003-08-12 15:40 unexpected IO-APIC Tom Parker
2003-08-08 16:49 Christian Stein
2003-07-29 13:52 Schulman.Andrew
2003-07-17 15:09 Unexpected IO-APIC Joe Brown
2003-07-12 23:34 unexpected IO-APIC Toth Szabolcs
2003-07-13 4:09 ` Randy.Dunlap
2003-06-09 21:52 Unexpected IO-APIC Julian R. Coombes
2003-06-07 10:06 unexpected IO-APIC Toni Mueller
2003-06-07 17:40 ` Randy.Dunlap
2003-06-05 10:37 Mimmus
2003-06-05 14:42 ` Randy.Dunlap
2003-06-04 2:19 Greg Norris
2003-05-29 19:44 Jürgen Adler
2003-05-24 3:15 Brian Laflum
2003-05-23 3:57 Ben Osborne
2003-05-25 20:07 ` Alan Cox
2003-05-22 7:02 Anders Tor Westerberg
2003-04-22 6:41 Ilo Lorusso
2003-04-18 2:43 Phaedrus
2003-04-16 23:36 lk
2003-04-17 11:43 ` Earle R. Nietzel
2003-04-17 18:46 ` lk
2003-04-17 20:28 ` Randy.Dunlap
2003-04-17 22:52 ` lk
2003-04-17 23:14 ` Randy.Dunlap
2003-04-10 12:22 Unexpected IO-APIC Milan Kerslager
2003-03-31 19:35 unexpected IO-APIC Pascal Hofmann
2003-03-27 18:03 Dennis Lambe Jr.
2003-03-27 12:13 Jakub Zawierucha
2003-03-15 11:46 Peter Ruskin
2003-03-08 17:14 Scott Beck
2003-03-02 15:03 Lorant Dobos
2003-02-27 8:14 Nick Gaugler
2003-02-22 0:50 Peter Ruskin
2003-02-06 22:59 Philipp Berndt
2003-02-01 22:15 Luis Claudio Pérez Tato
2003-01-30 11:24 Joern Strassemeyer
2003-01-30 6:55 Andrew Egin
2003-01-18 16:48 Andy Igoshin
2003-01-10 10:04 frontal
2003-01-03 6:19 Chris
2002-12-28 10:32 Jonathan Araña Cruz
2002-12-27 8:53 Marc
2002-12-19 5:21 Carlos Madrid
2002-12-16 12:21 Unexpected IO-APIC Pasquale Federico Zema
2002-12-10 9:50 unexpected IO-APIC Juan Pedro Paredes
2002-12-06 4:41 Toni Cerdà
2002-12-02 11:30 huba
2002-11-28 23:22 Erik Meusel
2002-11-29 0:40 ` Alan Cox
2002-11-27 10:42 Nigbur, Rolf (IKK-Bundesverband)
2002-11-27 12:36 ` Alan Cox
2002-11-25 9:59 Vitor Dias da Silva
2002-11-23 0:15 Unexpected IO-APIC Mick
2002-11-22 7:33 dix.edv
2002-10-20 22:43 unexpected IO-APIC John Osswald
2002-10-03 19:12 Unexpected IO-APIC Alexander Tsibulsky
2002-09-16 13:54 unexpected IO-APIC Juergen Rose
2002-08-24 12:21 Unexpected IO-APIC David Brownell
2002-08-18 14:27 unexpected IO-APIC Kim Bisgaard
2002-07-26 21:42 Joseph S. Wigton
2002-07-19 16:15 Barry Gamblin
2002-07-06 19:59 Paul Parsons
2002-06-28 19:05 Unexpected IO-APIC Jawaid.Bazyar
2002-06-20 15:26 Andrew Ott
2002-06-17 4:03 unexpected IO-APIC Adam Powers
2002-06-15 1:25 Steve Keith
2002-06-06 3:38 Chris Kogelnik
2002-06-01 18:52 Luigi Rosa
2002-06-01 19:59 ` Vladimir G. Ivanovic
2002-06-02 23:03 ` Randy.Dunlap
2002-05-31 12:43 Françoise Guilbault
2002-05-20 13:41 zoli
2002-05-20 14:31 ` Alan Cox
2002-05-03 23:00 unexpected io-apic Schroettner Robert
2002-05-03 8:10 unexpected IO-APIC Giulio Bottazzi
2002-04-09 18:52 Mauricio Girardi
2002-04-08 9:31 Paul Hemstock
2002-04-08 14:46 ` Randy.Dunlap
2001-09-03 10:30 Matt Bernstein
2000-12-19 17:37 Mathieu Chouquet-Stringer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20021217154659.6e70e560.heimanns@versanet.de \
--to=heimanns@versanet.de \
--cc=linux-smp@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.