From: Sterling Chavis <Sterling@Chavis.us>
To: linux-smp@vger.kernel.org
Subject: unexpected IO-APIC
Date: Fri, 12 Dec 2003 22:50:35 -0700 [thread overview]
Message-ID: <200312122250.35672.Sterling@Chavis.us> (raw)
This came from my Toshiba Satellite P25-S487 laptop with a P4 3.0GHz
HyperTreading processor. Please let me know if you need any more info.
Regards,
Sterling
---
dmesg
0000
Booting processor 1/1 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5980.16 BogoMIPS
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09
Total of 2 processors activated (11894.78 BogoMIPS).
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-2, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23
not connected.
..TIMER: vector=0x31 pin1=-1 pin2=0
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 15./
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00178020
....... : arbitration: 00
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 003 03 0 0 0 0 0 1 1 31
01 003 03 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 0 0 0 0 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 003 03 1 1 0 0 0 1 1 71
0a 003 03 0 0 0 0 0 1 1 79
0b 003 03 0 0 0 0 0 1 1 81
0c 003 03 0 0 0 0 0 1 1 89
0d 003 03 0 0 0 0 0 1 1 91
0e 003 03 0 0 0 0 0 1 1 99
0f 003 03 0 0 0 0 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:0
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2992.0014 MHz.
..... host bus clock speed is 199.0467 MHz.
cpu: 0, clocks: 199467, slice: 66489
CPU0<T0:199456,T1:132960,D:7,S:66489,C:199467>
cpu: 1, clocks: 199467, slice: 66489
CPU1<T0:199456,T1:66464,D:14,S:66489,C:199467>
checking TSC synchronization across CPUs: passed.
migration_task 0 on cpu=0
migration_task 1 on cpu=1
ACPI: Subsystem revision 20021122
PCI: PCI BIOS revision 2.10 entry at 0xfd994, last bus=2
PCI: Using configuration type 1
ACPI-0511: *** Info: GPE Block0 defined as GPE0 to GPE31
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs 5, enabled at IRQ 9)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5, enabled at IRQ 9)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15, disabled)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15, disabled)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15, disabled)
ACPI: PCI Interrupt Link [LNKH] (IRQs 5, enabled at IRQ 9)
ACPI: Embedded Controller [EC0] (gpe 28)
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xa9 -> IRQ 18)
00:00:1f[A] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17)
00:00:1f[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xb9 -> IRQ 16)
00:00:1d[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19)
00:00:1d[B] -> 2-19 -> IRQ 19
Pin 2-18 already programmed
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xc9 -> IRQ 23)
00:00:1d[D] -> 2-23 -> IRQ 23
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI enabled
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086, DID=24db
PCI: Device 00:1f.1 not available because of resource collisions
PCI_IDE: BIOS setup was incomplete.
PCI_IDE: chipset revision 2
PCI_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x1888-0x188f, BIOS settings: hdc:pio, hdd:pio
hda: TOSHIBA MK6021GAS, ATA DISK drive
hdc: DW-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 117210240 sectors (60012 MB), CHS=7296/255/63
ide-cd: passing drive hdc to ide-scsi emulation.
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TEAC Model: DW-224E Rev: F.0A
Type: CD-ROM ANSI SCSI revision: 02
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
reiserfs: checking transaction log (device 03:03) ...
Warning, log replay starting on readonly filesystem
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 128k freed
Adding Swap: 1004052k swap-space (priority -1)
SCSI subsystem driver Revision: 1.00
devfs_mk_dir(scsi): using old entry in dir: c2515680 ""
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xe0973800, 00:02:3f:82:3f:1a, IRQ 17
eth0: Identified 8139 chip type 'RTL-8139C'
1: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4496 Wed Jul
16 19:03:09 PDT 2003
ohci1394: $Rev: 578 $ Ben Collins <bcollins@debian.org>
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[c2004000-c20047ff] Max
Packet=[2048]
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
usb-uhci.c: $Revision: 1.275 $ time 01:11:26 Dec 11 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1800, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x1820, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x1840, IRQ 18
usb-uhci.c: Detected 2 ports
ieee1394: Host added: Node[00:1023] GUID[00023f3839002020] [Linux OHCI-1394]
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
usb-uhci.c: USB UHCI at I/O 0x1860, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
mice: PS/2 mouse device common for all mice
PCI: Setting latency timer of device 00:1d.7 to 64
hcd.c: ehci-hcd @ 00:1d.7, PCI device 8086:24dd (Intel Corp.)
hcd.c: irq 23, pci mem e0b64000
usb.c: new USB bus registered, assigned bus number 5
ehci-hcd.c: restricting 64bit DMA mappings to segment 0 ...
ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0
usb-uhci.c: interrupt, status 2, frame# 481
hub.c: USB hub found
hub.c: 8 ports detected
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Enabling device 02:02.0 (0000 -> 0002)
PCI: Enabling device 02:04.0 (0000 -> 0002)
PCI: Enabling device 02:04.1 (0000 -> 0002)
Yenta IRQ list 0000, PCI irq18
Socket status: 30000010
Yenta IRQ list 04b8, PCI irq16
Socket status: 30000007
Yenta IRQ list 04b8, PCI irq17
Socket status: 30000007
eth0: Setting 100mbps half-duplex based on auto-negotiated partner ability
40a1.
hub.c: new USB device 00:1d.0-1, assigned address 2
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: new USB device 00:1d.0-1.1, assigned address 3
input0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb1:3.0
hub.c: new USB device 00:1d.0-1.3, assigned address 4
input1: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb1:4.0
input2: USB HID v1.10 Pointer [Logitech Logitech USB Keyboard] on usb1:4.1
hub.c: new USB device 00:1d.0-1.4, assigned address 5
usb.c: USB device 5 (vend/prod 0x5da/0x99) is not claimed by any active
driver.
Real Time Clock Driver v1.10e
PCI: Setting latency timer of device 00:1f.5 to 64
intel8x0: clocking to 48000
blk: queue c01c8c24, I/O limit 4095Mb (mask 0xffffffff)
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x20f 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
hermes.c: 5 Apr 2002 David Gibson <hermes@gibson.dropbear.id.au>
orinoco.c 0.11b (David Gibson <hermes@gibson.dropbear.id.au> and others)
orinoco_cs.c 0.11b (David Gibson <hermes@gibson.dropbear.id.au> and others)
eth1: Station identity 001f:0001:0008:000a
eth1: Looks like a Lucent/Agere firmware version 8.10
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:02:2D:82:7D:A2
eth1: Station name "HERMES I"
eth1: ready
eth1: index 0x01: Vcc 3.3, irq 18, io 0x0100-0x013f
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
/dev/vmnet: open called by PID 1596 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: up
bridge-eth0: attached
/dev/vmnet: open called by PID 1608 (vmnet-bridge)
/dev/vmnet: hub 2 does not exist, allocating memory.
/dev/vmnet: port on hub 2 successfully opened
bridge-eth1: up
bridge-eth1: attached
/dev/vmnet: open called by PID 1634 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
lp0: using parport0 (polling).
lp0: console ready
/dev/vmnet: open called by PID 2356 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2371 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
inserting floppy driver for 2.4.20-gentoo-r9
FDC 0 is a post-1991 82077
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: unsupported bridge
agpgart: no supported devices found.
1: NVRM: AGPGART: unable to retrieve symbol table
devfs_mk_dir(cdroms): using old entry in dir: c2515680 ""
/dev/vmnet: open called by PID 3318 (vmware-vmx)
bridge-eth0: set IFF_PROMISC
eth0: Promiscuous mode enabled.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: clear IFF_PROMISC
/dev/vmmon: Vmx86_ReleaseVM: unlocked pages: 36, unlocked dirty pages: 0
/dev/vmnet: open called by PID 3432 (vmware-vmx)
bridge-eth0: set IFF_PROMISC
eth0: Promiscuous mode enabled.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: clear IFF_PROMISC
/dev/vmmon: Vmx86_ReleaseVM: unlocked pages: 32, unlocked dirty pages: 0
/dev/vmnet: open called by PID 3946 (vmware-vmx)
bridge-eth0: set IFF_PROMISC
eth0: Promiscuous mode enabled.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: clear IFF_PROMISC
/dev/vmmon: Vmx86_ReleaseVM: unlocked pages: 36, unlocked dirty pages: 0
/dev/vmnet: open called by PID 4189 (vmware-vmx)
bridge-eth0: set IFF_PROMISC
eth0: Promiscuous mode enabled.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: clear IFF_PROMISC
/dev/vmmon: Vmx86_ReleaseVM: unlocked pages: 32, unlocked dirty pages: 0
/dev/vmnet: open called by PID 4244 (vmware-vmx)
bridge-eth0: set IFF_PROMISC
eth0: Promiscuous mode enabled.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: clear IFF_PROMISC
/dev/vmmon: Vmx86_ReleaseVM: unlocked pages: 36, unlocked dirty pages: 0
/dev/vmnet: open called by PID 4312 (vmware-vmx)
bridge-eth0: set IFF_PROMISC
eth0: Promiscuous mode enabled.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: clear IFF_PROMISC
/dev/vmmon: Vmx86_ReleaseVM: unlocked pages: 32, unlocked dirty pages: 0
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
/dev/vmnet: open called by PID 4689 (vmware-vmx)
bridge-eth0: set IFF_PROMISC
eth0: Promiscuous mode enabled.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: clear IFF_PROMISC
/dev/vmmon: Vmx86_ReleaseVM: unlocked pages: 32, unlocked dirty pages: 0
next reply other threads:[~2003-12-13 5:50 UTC|newest]
Thread overview: 135+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-12-13 5:50 Sterling Chavis [this message]
-- strict thread matches above, loose matches on Subject: below --
2006-07-06 20:37 unexpected IO-APIC Danielle Hines
2006-07-07 13:12 ` Erik Mouw
2006-03-07 4:19 Mimi Zhou
2005-07-12 13:56 Unexpected IO-APIC Bill Baker
2005-07-12 16:42 ` randy_dunlap
2005-06-18 5:04 unexpected IO-APIC darshan
2005-05-26 8:44 Bernd Strebel
2005-05-27 5:33 ` randy_dunlap
2005-05-27 9:26 ` Bernd Strebel
2005-05-27 17:30 ` randy_dunlap
2005-05-27 22:24 ` Bernd Strebel
2005-05-30 22:43 ` randy_dunlap
2005-03-14 20:48 Unexpected IO-APIC Iuri Wickert
2005-03-15 20:32 ` Randy.Dunlap
2005-03-05 21:48 Marco van Beek
2005-03-15 20:23 ` Randy.Dunlap
2005-02-28 23:34 unexpected IO-APIC Mike Farnam
2005-03-15 17:48 ` Randy.Dunlap
2005-03-15 20:14 ` Randy.Dunlap
2005-01-31 17:41 Gary Buckmaster
2005-01-25 18:23 Unexpected IO-APIC Martin Slovacek
2005-01-25 18:59 ` Earle Nietzel
2004-12-28 6:58 unexpected IO-APIC Paul
2004-12-06 4:23 unexpected io-apic Simon Story
2004-07-23 20:33 unexpected IO-APIC Thomas Schlag
2004-07-08 7:52 S.K.Goel
2004-06-23 11:44 Jörg Lübbert
2004-06-23 11:42 Jörg Lübbert
2004-06-18 18:15 Unexpected IO-APIC GIN (Garreth Jeremiah)
2004-04-23 8:28 unexpected IO-APIC Piers Lauder
2004-04-18 17:53 dpn22
2004-04-07 8:11 JKolk
2004-04-01 14:32 Ian Jenkinson
2004-02-24 15:07 Unexpected IO-APIC Lyle Worthington
2004-02-24 16:38 ` Randy.Dunlap
2004-02-24 18:03 ` Lyle Worthington
2004-02-24 18:31 ` Randy.Dunlap
2004-02-15 8:24 unexpected IO-APIC Massa Takeuti
2004-01-16 3:40 Polyhead
2004-01-11 8:53 Russ McCallister
2003-12-18 7:21 Matthew Blakley
2003-11-23 6:38 W M Brelsford
2003-11-20 3:09 Chris Johns
2003-11-12 21:16 A.J. Duijn
2003-10-16 17:44 Lance Davis
2003-09-25 15:09 Unexpected IO-APIC David van Hoose
2003-09-11 16:36 unexpected IO-APIC John Birck
2003-09-04 16:37 Michael Sorrentino
2003-09-04 19:35 ` Alan Cox
2003-09-04 4:19 Unexpected IO-APIC Jeremy Sylvestre
2003-09-01 12:31 Alfonso Abeger
2003-08-21 7:51 Grage, Sascha
2003-08-12 15:40 unexpected IO-APIC Tom Parker
2003-08-08 16:49 Christian Stein
2003-07-29 13:52 Schulman.Andrew
2003-07-17 15:09 Unexpected IO-APIC Joe Brown
2003-07-12 23:34 unexpected IO-APIC Toth Szabolcs
2003-07-13 4:09 ` Randy.Dunlap
2003-06-09 21:52 Unexpected IO-APIC Julian R. Coombes
2003-06-07 10:06 unexpected IO-APIC Toni Mueller
2003-06-07 17:40 ` Randy.Dunlap
2003-06-05 10:37 Mimmus
2003-06-05 14:42 ` Randy.Dunlap
2003-06-04 2:19 Greg Norris
2003-05-29 19:44 Jürgen Adler
2003-05-24 3:15 Brian Laflum
2003-05-23 3:57 Ben Osborne
2003-05-25 20:07 ` Alan Cox
2003-05-22 7:02 Anders Tor Westerberg
2003-04-22 6:41 Ilo Lorusso
2003-04-18 2:43 Phaedrus
2003-04-16 23:36 lk
2003-04-17 11:43 ` Earle R. Nietzel
2003-04-17 18:46 ` lk
2003-04-17 20:28 ` Randy.Dunlap
2003-04-17 22:52 ` lk
2003-04-17 23:14 ` Randy.Dunlap
2003-04-10 12:22 Unexpected IO-APIC Milan Kerslager
2003-03-31 19:35 unexpected IO-APIC Pascal Hofmann
2003-03-27 18:03 Dennis Lambe Jr.
2003-03-27 12:13 Jakub Zawierucha
2003-03-15 11:46 Peter Ruskin
2003-03-08 17:14 Scott Beck
2003-03-02 15:03 Lorant Dobos
2003-02-27 8:14 Nick Gaugler
2003-02-22 0:50 Peter Ruskin
2003-02-06 22:59 Philipp Berndt
2003-02-01 22:15 Luis Claudio Pérez Tato
2003-01-30 11:24 Joern Strassemeyer
2003-01-30 6:55 Andrew Egin
2003-01-18 16:48 Andy Igoshin
2003-01-10 10:04 frontal
2003-01-03 6:19 Chris
2002-12-28 10:32 Jonathan Araña Cruz
2002-12-27 8:53 Marc
2002-12-19 5:21 Carlos Madrid
2002-12-17 14:46 Christian Heimanns
2002-12-16 12:21 Unexpected IO-APIC Pasquale Federico Zema
2002-12-10 9:50 unexpected IO-APIC Juan Pedro Paredes
2002-12-06 4:41 Toni Cerdà
2002-12-02 11:30 huba
2002-11-28 23:22 Erik Meusel
2002-11-29 0:40 ` Alan Cox
2002-11-27 10:42 Nigbur, Rolf (IKK-Bundesverband)
2002-11-27 12:36 ` Alan Cox
2002-11-25 9:59 Vitor Dias da Silva
2002-11-23 0:15 Unexpected IO-APIC Mick
2002-11-22 7:33 dix.edv
2002-10-20 22:43 unexpected IO-APIC John Osswald
2002-10-03 19:12 Unexpected IO-APIC Alexander Tsibulsky
2002-09-16 13:54 unexpected IO-APIC Juergen Rose
2002-08-24 12:21 Unexpected IO-APIC David Brownell
2002-08-18 14:27 unexpected IO-APIC Kim Bisgaard
2002-07-26 21:42 Joseph S. Wigton
2002-07-19 16:15 Barry Gamblin
2002-07-06 19:59 Paul Parsons
2002-06-28 19:05 Unexpected IO-APIC Jawaid.Bazyar
2002-06-20 15:26 Andrew Ott
2002-06-17 4:03 unexpected IO-APIC Adam Powers
2002-06-15 1:25 Steve Keith
2002-06-06 3:38 Chris Kogelnik
2002-06-01 18:52 Luigi Rosa
2002-06-01 19:59 ` Vladimir G. Ivanovic
2002-06-02 23:03 ` Randy.Dunlap
2002-05-31 12:43 Françoise Guilbault
2002-05-20 13:41 zoli
2002-05-20 14:31 ` Alan Cox
2002-05-03 23:00 unexpected io-apic Schroettner Robert
2002-05-03 8:10 unexpected IO-APIC Giulio Bottazzi
2002-04-09 18:52 Mauricio Girardi
2002-04-08 9:31 Paul Hemstock
2002-04-08 14:46 ` Randy.Dunlap
2001-09-03 10:30 Matt Bernstein
2000-12-19 17:37 Mathieu Chouquet-Stringer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200312122250.35672.Sterling@Chavis.us \
--to=sterling@chavis.us \
--cc=linux-smp@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.