* RAID is now working...
@ 1999-09-18 0:44 David A. Cooley
1999-09-18 1:41 ` David S. Miller
` (5 more replies)
0 siblings, 6 replies; 7+ messages in thread
From: David A. Cooley @ 1999-09-18 0:44 UTC (permalink / raw)
To: ultralinux
Not sure what happened, but I went thru and ran FDISK on every drive in the
raid and re-wrote the partition table to each one... Rebooted and ran
mkraid, now both groups work on different controllers... Something must
have gotten hosed in the partition table somehow, but it was only messed up
on the new controller (Same exact type as the old controller... Qlogic PTI
SBUS controller).
Just very odd...
Anyone know where I can get a firmware upgrade for the Qlogic SBUS cards
that will flash them under Linux??? (or how to do it from the boot prompt
on an Ultra II?????)
============================= David Cooley N5XMT Internet: N5XMT@bellsouth.net
Packet: N5XMT@KQ4LO.#INT.NC.USA.NA T.A.P.R. Member #7068
Sponges grow in the ocean... Wonder how deep it would be if they didn't?!
=============================
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: RAID is now working...
1999-09-18 0:44 RAID is now working David A. Cooley
@ 1999-09-18 1:41 ` David S. Miller
1999-09-18 1:50 ` David A. Cooley
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: David S. Miller @ 1999-09-18 1:41 UTC (permalink / raw)
To: ultralinux
Date: Fri, 17 Sep 1999 20:44:54 -0400
From: "David A. Cooley" <n5xmt@bellsouth.net>
Anyone know where I can get a firmware upgrade for the Qlogic SBUS
cards that will flash them under Linux??? (or how to do it from the
boot prompt on an Ultra II?????)
It needs to be loaded by the driver, so you'd need to update the
firmware in the drivers/scsi/qlogicpti_asm.h source file in the
kernel, then rebuild the kernel with the new driver and reboot.
Matt Jacob has newer firmware in his ISP driver collection, but I have
not tried nor tested it on any of my SBUS isp cards so I cannot say if
it works or not. In the past, my attempts to load newer firmware or
allow firmware loading on newer cards has resulted in one problem or
another and this is why it is not updated in the latest drivers, so
be forwarned.
Later,
David S. Miller
davem@redhat.com
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: RAID is now working...
1999-09-18 0:44 RAID is now working David A. Cooley
1999-09-18 1:41 ` David S. Miller
@ 1999-09-18 1:50 ` David A. Cooley
1999-09-19 21:02 ` Florian Lohoff
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: David A. Cooley @ 1999-09-18 1:50 UTC (permalink / raw)
To: ultralinux
At 06:41 PM 9/17/99 -0700, David S. Miller wrote:
> Date: Fri, 17 Sep 1999 20:44:54 -0400
> From: "David A. Cooley" <n5xmt@bellsouth.net>
>
> Anyone know where I can get a firmware upgrade for the Qlogic SBUS
> cards that will flash them under Linux??? (or how to do it from the
> boot prompt on an Ultra II?????)
>
>It needs to be loaded by the driver, so you'd need to update the
>firmware in the drivers/scsi/qlogicpti_asm.h source file in the
>kernel, then rebuild the kernel with the new driver and reboot.
>
>Matt Jacob has newer firmware in his ISP driver collection, but I have
>not tried nor tested it on any of my SBUS isp cards so I cannot say if
>it works or not. In the past, my attempts to load newer firmware or
>allow firmware loading on newer cards has resulted in one problem or
>another and this is why it is not updated in the latest drivers, so
>be forwarned.
Ah..
Is there a firmware that has problems, or will running 2 different firmware
levels in 2 cards cause problems?
My 2 cards are 1.21 and 1.25
============================= David Cooley N5XMT Internet: N5XMT@bellsouth.net
Packet: N5XMT@KQ4LO.#INT.NC.USA.NA T.A.P.R. Member #7068
Sponges grow in the ocean... Wonder how deep it would be if they didn't?!
=============================
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: RAID is now working...
1999-09-18 0:44 RAID is now working David A. Cooley
1999-09-18 1:41 ` David S. Miller
1999-09-18 1:50 ` David A. Cooley
@ 1999-09-19 21:02 ` Florian Lohoff
1999-09-19 23:40 ` David Cooley
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Florian Lohoff @ 1999-09-19 21:02 UTC (permalink / raw)
To: ultralinux
On Fri, Sep 17, 1999 at 09:50:55PM -0400, David A. Cooley wrote:
> At 06:41 PM 9/17/99 -0700, David S. Miller wrote:
> > Date: Fri, 17 Sep 1999 20:44:54 -0400
> > From: "David A. Cooley" <n5xmt@bellsouth.net>
> >
> > Anyone know where I can get a firmware upgrade for the Qlogic SBUS
> > cards that will flash them under Linux??? (or how to do it from the
> > boot prompt on an Ultra II?????)
> >
> >It needs to be loaded by the driver, so you'd need to update the
> >firmware in the drivers/scsi/qlogicpti_asm.h source file in the
> >kernel, then rebuild the kernel with the new driver and reboot.
> >
> >Matt Jacob has newer firmware in his ISP driver collection, but I have
> >not tried nor tested it on any of my SBUS isp cards so I cannot say if
> >it works or not. In the past, my attempts to load newer firmware or
> >allow firmware loading on newer cards has resulted in one problem or
> >another and this is why it is not updated in the latest drivers, so
> >be forwarned.
>
> Ah..
> Is there a firmware that has problems, or will running 2 different firmware
> levels in 2 cards cause problems?
> My 2 cards are 1.21 and 1.25
As i understand Dave and the Source on every initializing of the Cards
the firmware gets loaded into the chips ... So you will always
end up with the firmware in the driver ...
Flo
PS: I have got problems with the QlogicPTI SBUS too. I have problems
under high raid load where the SCSI bus seems to freeze (The drivers
does ongoing resets of the single targets which does not stop until
i switch the machine off)
PPS: I am also interested in testing new firmware ...
--
Florian Lohoff flo@rfc822.org +49-5241-470566
... The failure can be random; however, when it does occur, it is
catastrophic and is repeatable ... Cisco Field Notice
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: RAID is now working...
1999-09-18 0:44 RAID is now working David A. Cooley
` (2 preceding siblings ...)
1999-09-19 21:02 ` Florian Lohoff
@ 1999-09-19 23:40 ` David Cooley
1999-09-21 12:27 ` Florian Lohoff
1999-09-22 1:02 ` Florian Lohoff
5 siblings, 0 replies; 7+ messages in thread
From: David Cooley @ 1999-09-19 23:40 UTC (permalink / raw)
To: ultralinux
At 11:02 PM 9/19/1999 +0200, Florian Lohoff wrote:
>As i understand Dave and the Source on every initializing of the Cards
>the firmware gets loaded into the chips ... So you will always
>end up with the firmware in the driver ...
Yep... Looking at the code in qlogicpti.c that's what it does... The
firmware is in qlogicpti_asm.c
>Flo
>PS: I have got problems with the QlogicPTI SBUS too. I have problems
> under high raid load where the SCSI bus seems to freeze (The drivers
> does ongoing resets of the single targets which does not stop until
> i switch the machine off)
Mine started doing that on the second PTI card I installed... Got looking
at the boot messages where it first detects the cards... My old one
(working fine) is detected as ultra scsi... the "new one" is detected as
fast scsi... Both cards have the same SUN part number on them, but the
"new" one has ver 1.71 on the sticker on the prom on the board, and the
"old" one (the one that works all the time) has 1.73 on it. The code read
by the kernel driver in the boards is 1.21 for the one that fails and 1.25
on the good one.
=============================David Cooley N5XMT Internet: N5XMT@bellsouth.net
Packet: N5XMT@KQ4LO.#INT.NC.USA.NA T.A.P.R. Member #7068
We are Borg... Prepare to be assimilated!
=============================
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: RAID is now working...
1999-09-18 0:44 RAID is now working David A. Cooley
` (3 preceding siblings ...)
1999-09-19 23:40 ` David Cooley
@ 1999-09-21 12:27 ` Florian Lohoff
1999-09-22 1:02 ` Florian Lohoff
5 siblings, 0 replies; 7+ messages in thread
From: Florian Lohoff @ 1999-09-21 12:27 UTC (permalink / raw)
To: ultralinux
On Sun, Sep 19, 1999 at 07:40:59PM -0400, David Cooley wrote:
>
> Mine started doing that on the second PTI card I installed... Got looking
> at the boot messages where it first detects the cards... My old one
> (working fine) is detected as ultra scsi... the "new one" is detected as
> fast scsi... Both cards have the same SUN part number on them, but the
> "new" one has ver 1.71 on the sticker on the prom on the board, and the
> "old" one (the one that works all the time) has 1.73 on it. The code read
> by the kernel driver in the boards is 1.21 for the one that fails and 1.25
> on the good one.
All 3 cards i have build into my SparcServer 5 are Version 1.21 (by label
on the chips and also on detection)
Probably this all is an Firmware problem. BTW: Mine are all detected as
Fast-Wide controllers
Sep 12 15:37:00 puke kernel: qpti0: IRQ 53 SCSI ID 7 (Firmware 1.21
95/05/18) [Fast Wide, using single ended interface]
Sep 12 15:37:00 puke kernel: qpti1: IRQ 53 SCSI ID 7 (Firmware 1.21
95/05/18) [Fast Wide, using single ended interface]
Sep 12 15:37:00 puke kernel: qpti2: IRQ 53 SCSI ID 7 (Firmware 1.21
95/05/18) [Fast Wide, using single ended interface]
Sep 12 15:37:00 puke kernel: QPTI: Total of 3 PTI Qlogic/ISP hosts found,
3 actually in use.
So - Which way to go for new Firmware ?
Flo
--
Florian Lohoff flo@rfc822.org +49-5241-470566
... The failure can be random; however, when it does occur, it is
catastrophic and is repeatable ... Cisco Field Notice
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: RAID is now working...
1999-09-18 0:44 RAID is now working David A. Cooley
` (4 preceding siblings ...)
1999-09-21 12:27 ` Florian Lohoff
@ 1999-09-22 1:02 ` Florian Lohoff
5 siblings, 0 replies; 7+ messages in thread
From: Florian Lohoff @ 1999-09-22 1:02 UTC (permalink / raw)
To: ultralinux
On Sun, Sep 19, 1999 at 07:40:59PM -0400, David Cooley wrote:
>
> Mine started doing that on the second PTI card I installed... Got looking
> at the boot messages where it first detects the cards... My old one
> (working fine) is detected as ultra scsi... the "new one" is detected as
> fast scsi... Both cards have the same SUN part number on them, but the
> "new" one has ver 1.71 on the sticker on the prom on the board, and the
> "old" one (the one that works all the time) has 1.73 on it. The code read
> by the kernel driver in the boards is 1.21 for the one that fails and 1.25
> on the good one.
I just had a quick look. The Driver Firmware in the Kernel source
seems to be 1.31 (For non-PTI and 1.24 for PTI)... In one of the latest
Sun patches i found a 1.32 (Reverse *ng*n**r*ng). Ill try to make a
qlogicpti_asm.c compatible file (Without knowing what i am doing).
As my cards dont state "Performance Technologies" i think the 1.31 gets
loaded currently (dmesg states Firmware 1.21 but per design the firmware
gets loaded on initialization)
So long ...
Flo
--
Florian Lohoff flo@rfc822.org +49-5241-470566
... The failure can be random; however, when it does occur, it is
catastrophic and is repeatable ... Cisco Field Notice
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~1999-09-22 1:02 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
1999-09-18 0:44 RAID is now working David A. Cooley
1999-09-18 1:41 ` David S. Miller
1999-09-18 1:50 ` David A. Cooley
1999-09-19 21:02 ` Florian Lohoff
1999-09-19 23:40 ` David Cooley
1999-09-21 12:27 ` Florian Lohoff
1999-09-22 1:02 ` Florian Lohoff
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.