From: Lucas De Marchi <lucas.demarchi@intel.com>
To: intel-gfx@lists.freedesktop.org
Subject: [PATCH v3 15/23] drm/i915/tgl: Implement TGL DisplayPort training sequence
Date: Fri, 23 Aug 2019 01:20:47 -0700 [thread overview]
Message-ID: <20190823082055.5992-16-lucas.demarchi@intel.com> (raw)
In-Reply-To: <20190823082055.5992-1-lucas.demarchi@intel.com>
From: José Roberto de Souza <jose.souza@intel.com>
On TGL some registers moved from DDI to transcoder and the
DisplayPort training sequence has a separate BSpec page.
I started adding 'ifs' to the original intel_ddi_pre_enable_dp() but
it was becoming really hard to follow, so a new and cleaner function
for TGL was added with comments of all steps. It's similar to ICL,
but different enough to deserve a new function.
The rest of DisplayPort enable and the whole disable sequences
remained the same.
v2: FEC and DSC should be enabled on sink side before start link
training(Maarten reported and Manasi confirmed the DSC part)
v3: Add call to enable FEC on step 7.l(Manasi)
BSpec: 49190
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
---
drivers/gpu/drm/i915/display/intel_ddi.c | 139 ++++++++++++++++++++++-
drivers/gpu/drm/i915/display/intel_dp.c | 8 +-
2 files changed, 139 insertions(+), 8 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index 3eb73dbaf9fd..60017a5f5fa8 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -1761,7 +1761,14 @@ void intel_ddi_set_vc_payload_alloc(const struct intel_crtc_state *crtc_state,
I915_WRITE(TRANS_DDI_FUNC_CTL(cpu_transcoder), temp);
}
-void intel_ddi_enable_transcoder_func(const struct intel_crtc_state *crtc_state)
+/*
+ * Returns the TRANS_DDI_FUNC_CTL value based on CRTC state.
+ *
+ * Only intended to be used by intel_ddi_enable_transcoder_func() and
+ * intel_ddi_config_transcoder_func().
+ */
+static u32
+intel_ddi_transcoder_func_reg_val_get(const struct intel_crtc_state *crtc_state)
{
struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
struct intel_encoder *encoder = intel_ddi_get_crtc_encoder(crtc);
@@ -1852,6 +1859,33 @@ void intel_ddi_enable_transcoder_func(const struct intel_crtc_state *crtc_state)
temp |= DDI_PORT_WIDTH(crtc_state->lane_count);
}
+ return temp;
+}
+
+void intel_ddi_enable_transcoder_func(const struct intel_crtc_state *crtc_state)
+{
+ struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
+ struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
+ enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
+ u32 temp;
+
+ temp = intel_ddi_transcoder_func_reg_val_get(crtc_state);
+ I915_WRITE(TRANS_DDI_FUNC_CTL(cpu_transcoder), temp);
+}
+
+/*
+ * Same as intel_ddi_enable_transcoder_func() but it do not set the enable bit
+ */
+static void
+intel_ddi_config_transcoder_func(const struct intel_crtc_state *crtc_state)
+{
+ struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
+ struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
+ enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
+ u32 temp;
+
+ temp = intel_ddi_transcoder_func_reg_val_get(crtc_state);
+ temp &= ~TRANS_DDI_FUNC_ENABLE;
I915_WRITE(TRANS_DDI_FUNC_CTL(cpu_transcoder), temp);
}
@@ -3175,9 +3209,94 @@ static void intel_ddi_disable_fec_state(struct intel_encoder *encoder,
POSTING_READ(ctl);
}
-static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
- const struct intel_crtc_state *crtc_state,
- const struct drm_connector_state *conn_state)
+static void tgl_ddi_pre_enable_dp(struct intel_encoder *encoder,
+ const struct intel_crtc_state *crtc_state,
+ const struct drm_connector_state *conn_state)
+{
+ struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
+ struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+ enum phy phy = intel_port_to_phy(dev_priv, encoder->port);
+ struct intel_digital_port *dig_port = enc_to_dig_port(&encoder->base);
+ bool is_mst = intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST);
+ int level = intel_ddi_dp_level(intel_dp);
+
+ intel_dp_set_link_params(intel_dp, crtc_state->port_clock,
+ crtc_state->lane_count, is_mst);
+
+ /* 1.a got on intel_atomic_commit_tail() */
+
+ /* 2. */
+ intel_edp_panel_on(intel_dp);
+
+ /*
+ * 1.b, 3. and 4. is done before tgl_ddi_pre_enable_dp() by:
+ * haswell_crtc_enable()->intel_encoders_pre_pll_enable() and
+ * haswell_crtc_enable()->intel_enable_shared_dpll()
+ */
+
+ /* 5. */
+ if (!intel_phy_is_tc(dev_priv, phy) ||
+ dig_port->tc_mode != TC_PORT_TBT_ALT)
+ intel_display_power_get(dev_priv,
+ dig_port->ddi_io_power_domain);
+
+ /* 6. */
+ icl_program_mg_dp_mode(dig_port);
+
+ /*
+ * 7.a - Steps in this function should only be executed over MST
+ * master, what will be taken in care by MST hook
+ * intel_mst_pre_enable_dp()
+ */
+ intel_ddi_enable_pipe_clock(crtc_state);
+
+ /* 7.b */
+ intel_ddi_config_transcoder_func(crtc_state);
+
+ /* 7.d */
+ icl_disable_phy_clock_gating(dig_port);
+
+ /* 7.e */
+ icl_ddi_vswing_sequence(encoder, crtc_state->port_clock, level,
+ encoder->type);
+
+ /* 7.f */
+ if (intel_phy_is_combo(dev_priv, phy)) {
+ bool lane_reversal =
+ dig_port->saved_port_bits & DDI_BUF_PORT_REVERSAL;
+
+ intel_combo_phy_power_up_lanes(dev_priv, phy, false,
+ crtc_state->lane_count,
+ lane_reversal);
+ }
+
+ /* 7.g */
+ intel_ddi_init_dp_buf_reg(encoder);
+
+ if (!is_mst)
+ intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
+
+ intel_dp_sink_set_decompression_state(intel_dp, crtc_state, true);
+ /*
+ * DDI FEC: "anticipates enabling FEC encoding sets the FEC_READY bit
+ * in the FEC_CONFIGURATION register to 1 before initiating link
+ * training
+ */
+ intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
+ /* 7.c, 7.h, 7.i, 7.j */
+ intel_dp_start_link_train(intel_dp);
+
+ /* 7.k */
+ intel_dp_stop_link_train(intel_dp);
+
+ /* 7.l */
+ intel_ddi_enable_fec(encoder, crtc_state);
+ intel_dsc_enable(encoder, crtc_state);
+}
+
+static void hsw_ddi_pre_enable_dp(struct intel_encoder *encoder,
+ const struct intel_crtc_state *crtc_state,
+ const struct drm_connector_state *conn_state)
{
struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
@@ -3243,6 +3362,18 @@ static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
intel_dsc_enable(encoder, crtc_state);
}
+static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
+ const struct intel_crtc_state *crtc_state,
+ const struct drm_connector_state *conn_state)
+{
+ struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+
+ if (INTEL_GEN(dev_priv) >= 12)
+ tgl_ddi_pre_enable_dp(encoder, crtc_state, conn_state);
+ else
+ hsw_ddi_pre_enable_dp(encoder, crtc_state, conn_state);
+}
+
static void intel_ddi_pre_enable_hdmi(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state,
const struct drm_connector_state *conn_state)
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 943392faaea2..ece6375bf65d 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -4010,13 +4010,13 @@ void intel_dp_set_idle_link_train(struct intel_dp *intel_dp)
I915_WRITE(ctl, val);
/*
- * On PORT_A we can have only eDP in SST mode. There the only reason
- * we need to set idle transmission mode is to work around a HW issue
- * where we enable the pipe while not in idle link-training mode.
+ * Until TGL on PORT_A we can have only eDP in SST mode. There the only
+ * reason we need to set idle transmission mode is to work around a HW
+ * issue where we enable the pipe while not in idle link-training mode.
* In this case there is requirement to wait for a minimum number of
* idle patterns to be sent.
*/
- if (port == PORT_A)
+ if (port == PORT_A && INTEL_GEN(dev_priv) < 12)
return;
if (intel_de_wait_for_set(dev_priv, status,
--
2.23.0
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2019-08-23 8:54 UTC|newest]
Thread overview: 56+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-23 8:20 [PATCH v3 00/23] Tiger Lake batch 3 Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 01/23] drm/i915/tgl: Move GTCR register to cope with GAM MMIO address remap Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 02/23] drm/i915/tgl: Enable VD HCP/MFX sub-pipe power gating Lucas De Marchi
2019-09-13 7:06 ` Chris Wilson
2019-08-23 8:20 ` [PATCH v3 03/23] drm/i915/psr: Only handle interruptions of the transcoder in use Lucas De Marchi
2019-08-26 17:28 ` Imre Deak
2019-08-27 16:50 ` Lucas De Marchi
2019-08-28 16:29 ` Imre Deak
2019-08-28 22:16 ` Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 04/23] drm/i915/bdw+: Enable PSR in any eDP port Lucas De Marchi
2019-08-26 13:41 ` Imre Deak
2019-08-26 17:43 ` Runyan, Arthur J
2019-08-27 16:36 ` Lucas De Marchi
2019-08-27 17:55 ` Souza, Jose
2019-08-23 8:20 ` [PATCH v3 05/23] drm/i915: Guard and warn if more than one eDP panel is present Lucas De Marchi
2019-08-26 6:41 ` Anshuman Gupta
2019-08-23 8:20 ` [PATCH v3 06/23] drm/i915: Do not read PSR2 register in transcoders without PSR2 Lucas De Marchi
2019-08-26 14:21 ` Imre Deak
2019-08-26 16:32 ` Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 07/23] drm/i915/tgl: PSR link standby is not supported anymore Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 08/23] drm/i915/tgl: Access the right register when handling PSR interruptions Lucas De Marchi
2019-08-26 9:53 ` Anshuman Gupta
2019-08-26 16:56 ` Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 09/23] drm/i915/tgl: Add maximum resolution supported by PSR2 HW Lucas De Marchi
2019-08-24 11:06 ` Anshuman Gupta
2019-08-26 17:10 ` Lucas De Marchi
2019-08-26 17:17 ` Souza, Jose
2019-08-26 17:29 ` Lucas De Marchi
2019-08-26 17:33 ` Gupta, Anshuman
2019-08-23 8:20 ` [PATCH v3 10/23] drm/i915: Add for_each_new_intel_connector_in_state() Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 11/23] drm: Add for_each_oldnew_intel_crtc_in_state_reverse() Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 12/23] drm/i915: Disable pipes in reverse order Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 13/23] FIXME: drm/i915/tgl: Select master transcoder in DP MST Lucas De Marchi
2019-08-23 13:02 ` Ville Syrjälä
2019-08-23 8:20 ` [PATCH v3 14/23] drm/i915/tgl: move DP_TP_* to transcoder Lucas De Marchi
2019-08-23 12:25 ` Ville Syrjälä
2019-08-23 12:39 ` Ville Syrjälä
2019-08-23 8:20 ` Lucas De Marchi [this message]
2019-08-23 8:20 ` [PATCH v3 16/23] drm/i915/tgl: Do not apply WaIncreaseDefaultTLBEntries from GEN12 onwards Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 17/23] FIXME: drm/i915/tgl: Register state context definition for Gen12 Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 18/23] drm/i915/tgl/perf: use the same oa ctx_id format as icl Lucas De Marchi
2019-08-23 8:30 ` Lionel Landwerlin
2019-08-23 18:16 ` Umesh Nerlige Ramappa
2019-08-23 8:20 ` [PATCH v3 19/23] drm/i915/tgl: Gen-12 display loses Yf tiling and legacy CCS support Lucas De Marchi
2019-08-28 23:04 ` Matt Roper
2019-08-28 23:59 ` Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 20/23] drm/framebuffer/tgl: Format modifier for Intel Gen-12 render compression Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 21/23] drm/i915/tgl: Gen-12 render decompression Lucas De Marchi
2019-08-29 0:33 ` Matt Roper
2019-09-13 0:31 ` Sripada, Radhakrishna
2019-08-23 8:20 ` [PATCH v3 22/23] drm/framebuffer/tgl: Format modifier for Intel Gen-12 media compression Lucas De Marchi
2019-08-23 8:20 ` [PATCH v3 23/23] drm/i915/tgl: " Lucas De Marchi
2019-08-23 13:24 ` ✗ Fi.CI.CHECKPATCH: warning for Tiger Lake batch 3 (rev5) Patchwork
2019-08-23 13:28 ` ✗ Fi.CI.SPARSE: " Patchwork
2019-08-23 13:53 ` ✓ Fi.CI.BAT: success " Patchwork
2019-08-24 11:50 ` ✓ Fi.CI.IGT: " Patchwork
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190823082055.5992-16-lucas.demarchi@intel.com \
--to=lucas.demarchi@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox