From: Eliad Peller <eliad@wizery.com>
To: Luciano Coelho <coelho@ti.com>
Cc: <linux-wireless@vger.kernel.org>
Subject: [PATCH v2 24/40] wl12xx: call wl12xx_cmd_set_peer_state() in AP mode
Date: Sun, 14 Aug 2011 13:17:23 +0300 [thread overview]
Message-ID: <1313317059-16567-25-git-send-email-eliad@wizery.com> (raw)
In-Reply-To: <1313317059-16567-1-git-send-email-eliad@wizery.com>
After adding a station, call wl12xx_cmd_set_peer_state().
This is required for 11n support.
Change wl12xx_cmd_set_peer_state() prototype to get hlid
as param.
Signed-off-by: Eliad Peller <eliad@wizery.com>
---
drivers/net/wireless/wl12xx/cmd.c | 6 +++---
drivers/net/wireless/wl12xx/cmd.h | 2 +-
drivers/net/wireless/wl12xx/main.c | 6 +++++-
3 files changed, 9 insertions(+), 5 deletions(-)
diff --git a/drivers/net/wireless/wl12xx/cmd.c b/drivers/net/wireless/wl12xx/cmd.c
index 025fb14..d655e62 100644
--- a/drivers/net/wireless/wl12xx/cmd.c
+++ b/drivers/net/wireless/wl12xx/cmd.c
@@ -1318,26 +1318,26 @@ int wl1271_cmd_set_ap_key(struct wl1271 *wl, u16 action, u8 id, u8 key_type,
out:
kfree(cmd);
return ret;
}
-int wl12xx_cmd_set_peer_state(struct wl1271 *wl)
+int wl12xx_cmd_set_peer_state(struct wl1271 *wl, u8 hlid)
{
struct wl12xx_cmd_set_peer_state *cmd;
int ret = 0;
- wl1271_debug(DEBUG_CMD, "cmd set peer state (hlid=%d)", wl->sta_hlid);
+ wl1271_debug(DEBUG_CMD, "cmd set peer state (hlid=%d)", hlid);
cmd = kzalloc(sizeof(*cmd), GFP_KERNEL);
if (!cmd) {
ret = -ENOMEM;
goto out;
}
- cmd->hlid = wl->sta_hlid;
+ cmd->hlid = hlid;
cmd->state = WL1271_CMD_STA_STATE_CONNECTED;
ret = wl1271_cmd_send(wl, CMD_SET_PEER_STATE, cmd, sizeof(*cmd), 0);
if (ret < 0) {
wl1271_error("failed to send set peer state command");
goto out_free;
diff --git a/drivers/net/wireless/wl12xx/cmd.h b/drivers/net/wireless/wl12xx/cmd.h
index 8b32a57..740d27e 100644
--- a/drivers/net/wireless/wl12xx/cmd.h
+++ b/drivers/net/wireless/wl12xx/cmd.h
@@ -67,13 +67,13 @@ int wl12xx_cmd_set_default_wep_key(struct wl1271 *wl, u8 id, u8 hlid);
int wl1271_cmd_set_sta_key(struct wl1271 *wl, u16 action, u8 id, u8 key_type,
u8 key_size, const u8 *key, const u8 *addr,
u32 tx_seq_32, u16 tx_seq_16);
int wl1271_cmd_set_ap_key(struct wl1271 *wl, u16 action, u8 id, u8 key_type,
u8 key_size, const u8 *key, u8 hlid, u32 tx_seq_32,
u16 tx_seq_16);
-int wl12xx_cmd_set_peer_state(struct wl1271 *wl);
+int wl12xx_cmd_set_peer_state(struct wl1271 *wl, u8 hlid);
int wl12xx_roc(struct wl1271 *wl, u8 role_id);
int wl12xx_croc(struct wl1271 *wl, u8 role_id);
int wl12xx_cmd_add_peer(struct wl1271 *wl, struct ieee80211_sta *sta, u8 hlid);
int wl12xx_cmd_remove_peer(struct wl1271 *wl, u8 hlid);
int wl12xx_cmd_config_fwlog(struct wl1271 *wl);
int wl12xx_cmd_start_fwlog(struct wl1271 *wl);
diff --git a/drivers/net/wireless/wl12xx/main.c b/drivers/net/wireless/wl12xx/main.c
index bf9b27d..9b0df66 100644
--- a/drivers/net/wireless/wl12xx/main.c
+++ b/drivers/net/wireless/wl12xx/main.c
@@ -392,13 +392,13 @@ static int wl1271_check_operstate(struct wl1271 *wl, unsigned char operstate)
if (operstate != IF_OPER_UP)
return 0;
if (test_and_set_bit(WL1271_FLAG_STA_STATE_SENT, &wl->flags))
return 0;
- ret = wl12xx_cmd_set_peer_state(wl);
+ ret = wl12xx_cmd_set_peer_state(wl, wl->sta_hlid);
if (ret < 0)
return ret;
wl12xx_croc(wl, wl->role_id);
wl1271_info("Association completed.");
@@ -3673,12 +3673,16 @@ static int wl1271_op_sta_add(struct ieee80211_hw *hw,
goto out_free_sta;
ret = wl12xx_cmd_add_peer(wl, sta, hlid);
if (ret < 0)
goto out_sleep;
+ ret = wl12xx_cmd_set_peer_state(wl, hlid);
+ if (ret < 0)
+ goto out_sleep;
+
out_sleep:
wl1271_ps_elp_sleep(wl);
out_free_sta:
if (ret < 0)
wl1271_free_sta(wl, hlid);
--
1.7.6.401.g6a319
next prev parent reply other threads:[~2011-08-14 10:17 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-08-14 10:16 [PATCH v2 00/40] wl12xx: move to wl12xx-fw-3 Eliad Peller
2011-08-14 10:17 ` [PATCH v2 01/40] wl12xx: Revert "wl12xx: schedule TX packets according to FW occupancy" Eliad Peller
2011-08-14 10:17 ` [PATCH v2 02/40] wl12xx: Use a single fw for both STA and AP roles Eliad Peller
2011-08-14 10:17 ` [PATCH v2 03/40] wl12xx: use 1 spare block in all cases Eliad Peller
2011-08-14 10:17 ` [PATCH v2 04/40] wl12xx: temporarily disable advanced ap functions Eliad Peller
2011-08-14 10:17 ` [PATCH v2 05/40] wl12xx: remove rx filtering stuff Eliad Peller
2011-08-14 10:17 ` [PATCH v2 06/40] wl12xx: update fw status struct Eliad Peller
2011-08-14 10:17 ` [PATCH v2 07/40] wl12xx: update acx commands Eliad Peller
2011-08-14 10:17 ` [PATCH v2 08/40] wl12xx: update commands & events Eliad Peller
2011-08-14 10:17 ` [PATCH v2 09/40] wl12xx: enable/disable role on interface add/remove Eliad Peller
2011-08-14 10:17 ` [PATCH v2 10/40] wl12xx: add device role commands Eliad Peller
2011-08-14 10:17 ` [PATCH v2 11/40] wl12xx: update scan cmd api Eliad Peller
2011-08-14 10:17 ` [PATCH v2 12/40] wl12xx: update rx/tx Eliad Peller
2011-08-14 10:17 ` [PATCH v2 13/40] wl12xx: change max/default template size Eliad Peller
2011-08-14 10:17 ` [PATCH v2 14/40] wl12xx: use wl1271_acx_beacon_filter_opt for both sta and ap Eliad Peller
2011-08-14 10:17 ` [PATCH v2 15/40] wl12xx: add set_rate_mgmt_params acx Eliad Peller
2011-08-14 10:17 ` [PATCH v2 16/40] wl12xx: add system_hlid Eliad Peller
2011-08-14 10:17 ` [PATCH v2 17/40] wl12xx: add ROC/CROC commands Eliad Peller
2011-08-14 10:17 ` [PATCH v2 18/40] wl12xx: replace dummy_join with " Eliad Peller
2011-08-14 10:17 ` [PATCH v2 19/40] wl12xx: handle dummy packet event also in ap mode Eliad Peller
2011-08-14 10:17 ` [PATCH v2 20/40] wl12xx: update BT coex configuration params Eliad Peller
2011-08-14 10:17 ` [PATCH v2 21/40] wl12xx: fix session counter Eliad Peller
2011-08-14 10:17 ` [PATCH v2 22/40] wl12xx: use dynamic hlids for AP-mode Eliad Peller
2011-08-14 10:17 ` [PATCH v2 23/40] wl12xx: re-enable block ack session support Eliad Peller
2011-08-14 10:17 ` Eliad Peller [this message]
2011-08-14 10:17 ` [PATCH v2 25/40] wl12xx: don't remove key if hlid was already deleted Eliad Peller
2011-08-14 10:17 ` [PATCH v2 26/40] wl12xx: add wl12xx_cmd_role_start_ibss() Eliad Peller
2011-08-14 10:17 ` [PATCH v2 27/40] wl12xx: support IBSS vif type Eliad Peller
2011-08-14 10:17 ` [PATCH v2 28/40] wl12xx: AP-mode - set STA HT capabilities when adding a STA Eliad Peller
2011-08-14 10:17 ` [PATCH v2 29/40] wl12xx: AP-mode - configure STA HT rates on join Eliad Peller
2011-08-14 10:17 ` [PATCH v2 30/40] wl12xx: AP-mode - configure HT rate support to the FW Eliad Peller
2011-08-14 10:17 ` [PATCH v2 31/40] wl12xx: use ap_bcast_hlid for recorded keys Eliad Peller
2011-08-14 10:17 ` [PATCH v2 32/40] wl12xx: don't remove key if hlid was already deleted Eliad Peller
2011-08-14 10:17 ` [PATCH v2 33/40] wl12xx: track freed packets in FW by AC Eliad Peller
2011-08-14 10:17 ` [PATCH v2 34/40] wl12xx: schedule TX packets according to FW packet occupancy Eliad Peller
2011-08-14 10:17 ` [PATCH v2 35/40] wl12xx: handle wrap-around overflow in released Tx blocks FW counter Eliad Peller
2011-08-14 10:17 ` [PATCH v2 36/40] wl12xx: enable AP advanced functionality Eliad Peller
2011-08-14 10:17 ` [PATCH v2 37/40] wl12xx: don't wait for disconnection event Eliad Peller
2011-08-14 10:17 ` [PATCH v2 38/40] wl12xx: set the AP-started flag only after setting keys Eliad Peller
2011-08-14 10:17 ` [PATCH v2 39/40] wl12xx: AP-mode - prevent Tx to stale/invalid stations Eliad Peller
2011-08-14 10:17 ` [PATCH v2 40/40] wl12xx: fix tx_queue_count spurious increment Eliad Peller
2011-08-22 11:11 ` [PATCH v2 00/40] wl12xx: move to wl12xx-fw-3 Luciano Coelho
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1313317059-16567-25-git-send-email-eliad@wizery.com \
--to=eliad@wizery.com \
--cc=coelho@ti.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox