From: Suraj Kandpal <suraj.kandpal@intel.com>
To: intel-xe@lists.freedesktop.org, intel-gfx@lists.freedesktop.org
Cc: ankit.k.nautiyal@intel.com, arun.r.murthy@intel.com,
uma.shankar@intel.com, gustavo.sousa@intel.com,
lucas.demarchi@intel.com, Suraj Kandpal <suraj.kandpal@intel.com>
Subject: [PATCH 03/25] drm/i915/ltphy: Phy lane reset for LT Phy
Date: Wed, 15 Oct 2025 09:37:55 +0530 [thread overview]
Message-ID: <20251015040817.3431297-4-suraj.kandpal@intel.com> (raw)
In-Reply-To: <20251015040817.3431297-1-suraj.kandpal@intel.com>
Define function to bring phy lane out of reset for LT Phy and the
corresponding pre-requisite steps before we follow the steps for
Phy lane reset. Also create a skeleton of LT PHY PLL enable sequence
function in which we can place this function
Bspec: 77449, 74749, 74499, 74495, 68960
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
---
drivers/gpu/drm/i915/Makefile | 1 +
drivers/gpu/drm/i915/display/intel_cx0_phy.c | 2 +-
drivers/gpu/drm/i915/display/intel_cx0_phy.h | 2 +
.../gpu/drm/i915/display/intel_cx0_phy_regs.h | 4 +
drivers/gpu/drm/i915/display/intel_lt_phy.c | 159 ++++++++++++++++++
drivers/gpu/drm/i915/display/intel_lt_phy.h | 17 ++
.../gpu/drm/i915/display/intel_lt_phy_regs.h | 17 ++
drivers/gpu/drm/xe/Makefile | 1 +
8 files changed, 202 insertions(+), 1 deletion(-)
create mode 100644 drivers/gpu/drm/i915/display/intel_lt_phy.c
create mode 100644 drivers/gpu/drm/i915/display/intel_lt_phy.h
diff --git a/drivers/gpu/drm/i915/Makefile b/drivers/gpu/drm/i915/Makefile
index 6d7800e25e55..33836829d2c0 100644
--- a/drivers/gpu/drm/i915/Makefile
+++ b/drivers/gpu/drm/i915/Makefile
@@ -352,6 +352,7 @@ i915-y += \
display/intel_gmbus.o \
display/intel_hdmi.o \
display/intel_lspcon.o \
+ display/intel_lt_phy.o \
display/intel_lvds.o \
display/intel_panel.o \
display/intel_pfit.o \
diff --git a/drivers/gpu/drm/i915/display/intel_cx0_phy.c b/drivers/gpu/drm/i915/display/intel_cx0_phy.c
index 6d9ebc8717ba..db2b05521c62 100644
--- a/drivers/gpu/drm/i915/display/intel_cx0_phy.c
+++ b/drivers/gpu/drm/i915/display/intel_cx0_phy.c
@@ -2843,7 +2843,7 @@ static void intel_cx0_powerdown_change_sequence(struct intel_encoder *encoder,
phy_name(phy), XELPDP_PORT_RESET_START_TIMEOUT_US);
}
-static void intel_cx0_setup_powerdown(struct intel_encoder *encoder)
+void intel_cx0_setup_powerdown(struct intel_encoder *encoder)
{
struct intel_display *display = to_intel_display(encoder);
enum port port = encoder->port;
diff --git a/drivers/gpu/drm/i915/display/intel_cx0_phy.h b/drivers/gpu/drm/i915/display/intel_cx0_phy.h
index c5a7b529955b..c92026fe7b8f 100644
--- a/drivers/gpu/drm/i915/display/intel_cx0_phy.h
+++ b/drivers/gpu/drm/i915/display/intel_cx0_phy.h
@@ -41,6 +41,8 @@ bool intel_cx0pll_compare_hw_state(const struct intel_cx0pll_state *a,
const struct intel_cx0pll_state *b);
void intel_cx0_phy_set_signal_levels(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state);
+int intel_cx0_phy_check_hdmi_link_rate(struct intel_hdmi *hdmi, int clock);
+void intel_cx0_setup_powerdown(struct intel_encoder *encoder);
int intel_mtl_tbt_calc_port_clock(struct intel_encoder *encoder);
void intel_cx0_pll_power_save_wa(struct intel_display *display);
void intel_lnl_mac_transmit_lfps(struct intel_encoder *encoder,
diff --git a/drivers/gpu/drm/i915/display/intel_cx0_phy_regs.h b/drivers/gpu/drm/i915/display/intel_cx0_phy_regs.h
index 18b91c23d547..114f6b2113db 100644
--- a/drivers/gpu/drm/i915/display/intel_cx0_phy_regs.h
+++ b/drivers/gpu/drm/i915/display/intel_cx0_phy_regs.h
@@ -104,6 +104,8 @@
#define XELPDP_PORT_BUF_PORT_DATA_20BIT REG_FIELD_PREP(XELPDP_PORT_BUF_PORT_DATA_WIDTH_MASK, 1)
#define XELPDP_PORT_BUF_PORT_DATA_40BIT REG_FIELD_PREP(XELPDP_PORT_BUF_PORT_DATA_WIDTH_MASK, 2)
#define XELPDP_PORT_REVERSAL REG_BIT(16)
+#define XE3PLPDP_PHY_MODE_MASK REG_GENMASK(15, 12)
+#define XE3PLPDP_PHY_MODE_DP REG_FIELD_PREP(XE3PLPDP_PHY_MODE_MASK, 0x3)
#define XELPDP_PORT_BUF_IO_SELECT_TBT REG_BIT(11)
#define XELPDP_PORT_BUF_PHY_IDLE REG_BIT(7)
#define XELPDP_TC_PHY_OWNERSHIP REG_BIT(6)
@@ -124,6 +126,7 @@
_XELPDP_PORT_BUF_CTL2(port))
#define XELPDP_LANE_PIPE_RESET(lane) _PICK(lane, REG_BIT(31), REG_BIT(30))
#define XELPDP_LANE_PHY_CURRENT_STATUS(lane) _PICK(lane, REG_BIT(29), REG_BIT(28))
+#define XE3PLPDP_LANE_PHY_PULSE_STATUS(lane) _PICK(lane, REG_BIT(27), REG_BIT(26))
#define XELPDP_LANE_POWERDOWN_UPDATE(lane) _PICK(lane, REG_BIT(25), REG_BIT(24))
#define _XELPDP_LANE0_POWERDOWN_NEW_STATE_MASK REG_GENMASK(23, 20)
#define _XELPDP_LANE0_POWERDOWN_NEW_STATE(val) REG_FIELD_PREP(_XELPDP_LANE0_POWERDOWN_NEW_STATE_MASK, val)
@@ -151,6 +154,7 @@
#define XELPDP_POWER_STATE_ACTIVE(val) REG_FIELD_PREP(XELPDP_POWER_STATE_ACTIVE_MASK, val)
#define XELPDP_P0_STATE_ACTIVE 0x0
#define XELPDP_P2_STATE_READY 0x2
+#define XE3PLPD_P4_STATE_DISABLE 0x4
#define XELPDP_P2PG_STATE_DISABLE 0x9
#define XELPDP_P4PG_STATE_DISABLE 0xC
#define XELPDP_P2_STATE_RESET 0x2
diff --git a/drivers/gpu/drm/i915/display/intel_lt_phy.c b/drivers/gpu/drm/i915/display/intel_lt_phy.c
new file mode 100644
index 000000000000..c65333cc9494
--- /dev/null
+++ b/drivers/gpu/drm/i915/display/intel_lt_phy.c
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: MIT
+/*
+ * Copyright © 2025 Intel Corporation
+ */
+
+#include <drm/drm_print.h>
+
+#include "i915_reg.h"
+#include "intel_cx0_phy.h"
+#include "intel_cx0_phy_regs.h"
+#include "intel_de.h"
+#include "intel_display.h"
+#include "intel_display_types.h"
+#include "intel_lt_phy.h"
+#include "intel_lt_phy_regs.h"
+#include "intel_tc.h"
+
+#define INTEL_LT_PHY_LANE0 BIT(0)
+#define INTEL_LT_PHY_LANE1 BIT(1)
+#define INTEL_LT_PHY_BOTH_LANES (INTEL_LT_PHY_LANE1 |\
+ INTEL_LT_PHY_LANE0)
+
+static u8 intel_lt_phy_get_owned_lane_mask(struct intel_encoder *encoder)
+{
+ struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
+
+ if (!intel_tc_port_in_dp_alt_mode(dig_port))
+ return INTEL_LT_PHY_BOTH_LANES;
+
+ return intel_tc_port_max_lane_count(dig_port) > 2
+ ? INTEL_LT_PHY_BOTH_LANES : INTEL_LT_PHY_LANE0;
+}
+
+static void
+intel_lt_phy_setup_powerdown(struct intel_encoder *encoder, u8 lane_count)
+{
+ /*
+ * The new PORT_BUF_CTL6 stuff for dc5 entry and exit needs to be handled
+ * by dmc firmware not explicitly mentioned in Bspec. This leaves this
+ * function as a wrapper only but keeping it expecting future changes.
+ */
+ intel_cx0_setup_powerdown(encoder);
+}
+
+static void
+intel_lt_phy_lane_reset(struct intel_encoder *encoder,
+ u8 lane_count)
+{
+ struct intel_display *display = to_intel_display(encoder);
+ enum port port = encoder->port;
+ enum phy phy = intel_encoder_to_phy(encoder);
+ u8 owned_lane_mask = intel_lt_phy_get_owned_lane_mask(encoder);
+ u32 lane_pipe_reset = owned_lane_mask == INTEL_LT_PHY_BOTH_LANES
+ ? XELPDP_LANE_PIPE_RESET(0) | XELPDP_LANE_PIPE_RESET(1)
+ : XELPDP_LANE_PIPE_RESET(0);
+ u32 lane_phy_current_status = owned_lane_mask == INTEL_LT_PHY_BOTH_LANES
+ ? (XELPDP_LANE_PHY_CURRENT_STATUS(0) |
+ XELPDP_LANE_PHY_CURRENT_STATUS(1))
+ : XELPDP_LANE_PHY_CURRENT_STATUS(0);
+ u32 lane_phy_pulse_status = owned_lane_mask == INTEL_LT_PHY_BOTH_LANES
+ ? (XE3PLPDP_LANE_PHY_PULSE_STATUS(0) |
+ XE3PLPDP_LANE_PHY_PULSE_STATUS(1))
+ : XE3PLPDP_LANE_PHY_PULSE_STATUS(0);
+
+ intel_de_rmw(display, XE3PLPD_PORT_BUF_CTL5(port),
+ XE3PLPD_MACCLK_RATE_MASK, XE3PLPD_MACCLK_RATE_DEF);
+
+ intel_de_rmw(display, XELPDP_PORT_BUF_CTL1(display, port),
+ XE3PLPDP_PHY_MODE_MASK, XE3PLPDP_PHY_MODE_DP);
+
+ intel_lt_phy_setup_powerdown(encoder, lane_count);
+
+ intel_de_rmw(display, XE3PLPD_PORT_BUF_CTL5(port),
+ XE3PLPD_MACCLK_RESET_0, 0);
+
+ intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, port),
+ XELPDP_LANE_PCLK_PLL_REQUEST(0),
+ XELPDP_LANE_PCLK_PLL_REQUEST(0));
+
+ if (intel_de_wait_custom(display, XELPDP_PORT_CLOCK_CTL(display, port),
+ XELPDP_LANE_PCLK_PLL_ACK(0),
+ XELPDP_LANE_PCLK_PLL_ACK(0),
+ XE3PLPD_MACCLK_TURNON_LATENCY_US,
+ XE3PLPD_MACCLK_TURNON_LATENCY_MS, NULL))
+ drm_warn(display->drm, "PHY %c PLL MacCLK assertion Ack not done after %dus.\n",
+ phy_name(phy), XE3PLPD_MACCLK_TURNON_LATENCY_MS * 1000);
+
+ intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, port),
+ XELPDP_FORWARD_CLOCK_UNGATE,
+ XELPDP_FORWARD_CLOCK_UNGATE);
+
+ intel_de_rmw(display, XELPDP_PORT_BUF_CTL2(display, port),
+ lane_pipe_reset | lane_phy_pulse_status, 0);
+
+ if (intel_de_wait_custom(display, XELPDP_PORT_BUF_CTL2(display, port),
+ lane_phy_current_status, 0,
+ XE3PLPD_RESET_END_LATENCY_US, 2, NULL))
+ drm_warn(display->drm,
+ "PHY %c failed to bring out of Lane reset after %dus.\n",
+ phy_name(phy), XE3PLPD_RESET_END_LATENCY_US);
+
+ if (intel_de_wait_custom(display, XELPDP_PORT_BUF_CTL2(display, port),
+ lane_phy_pulse_status, lane_phy_pulse_status,
+ XE3PLPD_RATE_CALIB_DONE_LATENCY_US, 0, NULL))
+ drm_warn(display->drm, "PHY %c PLL rate not changed after %dus.\n",
+ phy_name(phy), XE3PLPD_RATE_CALIB_DONE_LATENCY_US);
+
+ intel_de_rmw(display, XELPDP_PORT_BUF_CTL2(display, port), lane_phy_pulse_status, 0);
+}
+
+void intel_lt_phy_pll_enable(struct intel_encoder *encoder,
+ const struct intel_crtc_state *crtc_state)
+{
+ /* 1. Enable MacCLK at default 162 MHz frequency. */
+ intel_lt_phy_lane_reset(encoder, crtc_state->lane_count);
+
+ /* 2. Program PORT_CLOCK_CTL register to configure clock muxes, gating, and SSC. */
+ /* 3. Change owned PHY lanes power to Ready state. */
+ /*
+ * 4. Read the PHY message bus VDR register PHY_VDR_0_Config check enabled PLL type,
+ * encoded rate and encoded mode.
+ */
+ /*
+ * 5. Program the PHY internal PLL registers over PHY message bus for the desired
+ * frequency and protocol type
+ */
+ /* 6. Use the P2P transaction flow */
+ /*
+ * 6.1. Set the PHY VDR register 0xCC4[Rate Control VDR Update] = 1 over PHY message
+ * bus for Owned PHY Lanes.
+ */
+ /*
+ * 6.2. Poll for P2P Transaction Ready = "1" and read the MAC message bus VDR register
+ * at offset 0xC00 for Owned PHY Lanes.
+ */
+ /* 6.3. Clear P2P transaction Ready bit. */
+ /* 7. Program PORT_CLOCK_CTL[PCLK PLL Request LN0] = 0. */
+ /* 8. Poll for PORT_CLOCK_CTL[PCLK PLL Ack LN0]= 0. */
+ /*
+ * 9. Follow the Display Voltage Frequency Switching - Sequence Before Frequency Change.
+ * We handle this step in bxt_set_cdclk()
+ */
+ /* 10. Program DDI_CLK_VALFREQ to match intended DDI clock frequency. */
+ /* 11. Program PORT_CLOCK_CTL[PCLK PLL Request LN0] = 1. */
+ /* 12. Poll for PORT_CLOCK_CTL[PCLK PLL Ack LN0]= 1. */
+ /* 13. Ungate the forward clock by setting PORT_CLOCK_CTL[Forward Clock Ungate] = 1. */
+ /* 14. SW clears PORT_BUF_CTL2 [PHY Pulse Status]. */
+ /*
+ * 15. Clear the PHY VDR register 0xCC4[Rate Control VDR Update] over PHY message bus for
+ * Owned PHY Lanes.
+ */
+ /* 16. Poll for PORT_BUF_CTL2 register PHY Pulse Status = 1 for Owned PHY Lanes. */
+ /* 17. SW clears PORT_BUF_CTL2 [PHY Pulse Status]. */
+ /*
+ * 18. Follow the Display Voltage Frequency Switching - Sequence After Frequency Change.
+ * We handle this step in bxt_set_cdclk()
+ */
+ /* 19. Move the PHY powerdown state to Active and program to enable/disable transmitters */
+}
diff --git a/drivers/gpu/drm/i915/display/intel_lt_phy.h b/drivers/gpu/drm/i915/display/intel_lt_phy.h
new file mode 100644
index 000000000000..bd3ff3007e1d
--- /dev/null
+++ b/drivers/gpu/drm/i915/display/intel_lt_phy.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: MIT
+ *
+ * Copyright © 2025 Intel Corporation
+ */
+
+#ifndef __INTEL_LT_PHY_H__
+#define __INTEL_LT_PHY_H__
+
+#include <linux/types.h>
+
+struct intel_encoder;
+struct intel_crtc_state;
+
+void intel_lt_phy_pll_enable(struct intel_encoder *encoder,
+ const struct intel_crtc_state *crtc_state);
+
+#endif /* __INTEL_LT_PHY_H__ */
diff --git a/drivers/gpu/drm/i915/display/intel_lt_phy_regs.h b/drivers/gpu/drm/i915/display/intel_lt_phy_regs.h
index 499acb1975d1..a4aa2a3e0425 100644
--- a/drivers/gpu/drm/i915/display/intel_lt_phy_regs.h
+++ b/drivers/gpu/drm/i915/display/intel_lt_phy_regs.h
@@ -9,6 +9,12 @@
#include "i915_reg_defs.h"
#include "intel_display_limits.h"
+#define XE3PLPD_MACCLK_TURNON_LATENCY_MS 1
+#define XE3PLPD_MACCLK_TURNON_LATENCY_US 21
+#define XE3PLPD_RATE_CALIB_DONE_LATENCY_US 50
+#define XE3PLPD_RESET_START_LATENCY_US 10
+#define XE3PLPD_RESET_END_LATENCY_US 200
+
/* LT Phy Vendor Register */
#define LT_PHY_VDR_0_CONFIG 0xC02
#define LT_PHY_VDR_DP_PLL_ENABLE REG_BIT(7)
@@ -24,4 +30,15 @@
#define LT_PHY_RATE_UPDATE 0xCC4
+#define _XE3PLPD_PORT_BUF_CTL5(idx) _MMIO(_PICK_EVEN_2RANGES(idx, PORT_TC1, \
+ _XELPDP_PORT_BUF_CTL1_LN0_A, \
+ _XELPDP_PORT_BUF_CTL1_LN0_B, \
+ _XELPDP_PORT_BUF_CTL1_LN0_USBC1, \
+ _XELPDP_PORT_BUF_CTL1_LN0_USBC2) \
+ + 0x34)
+#define XE3PLPD_PORT_BUF_CTL5(port) _XE3PLPD_PORT_BUF_CTL5(__xe2lpd_port_idx(port))
+#define XE3PLPD_MACCLK_RESET_0 REG_BIT(11)
+#define XE3PLPD_MACCLK_RATE_MASK REG_GENMASK(4, 0)
+#define XE3PLPD_MACCLK_RATE_DEF REG_FIELD_PREP(XE3PLPD_MACCLK_RATE_MASK, 0x1F)
+
#endif /* __INTEL_LT_PHY_REGS_H__ */
diff --git a/drivers/gpu/drm/xe/Makefile b/drivers/gpu/drm/xe/Makefile
index 84321fad3265..314aeea0f1e3 100644
--- a/drivers/gpu/drm/xe/Makefile
+++ b/drivers/gpu/drm/xe/Makefile
@@ -291,6 +291,7 @@ xe-$(CONFIG_DRM_XE_DISPLAY) += \
i915-display/intel_hti.o \
i915-display/intel_link_bw.o \
i915-display/intel_lspcon.o \
+ i915-display/intel_lt_phy.o \
i915-display/intel_modeset_lock.o \
i915-display/intel_modeset_setup.o \
i915-display/intel_modeset_verify.o \
--
2.34.1
next prev parent reply other threads:[~2025-10-15 4:08 UTC|newest]
Thread overview: 61+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-15 4:07 [PATCH 00/25] Enable LT PHY Suraj Kandpal
2025-10-15 4:07 ` [PATCH 01/25] drm/i915/ltphy: Add LT Phy related VDR and Pipe Registers Suraj Kandpal
2025-10-20 11:10 ` Jani Nikula
2025-10-22 4:05 ` Kandpal, Suraj
2025-10-22 7:57 ` Murthy, Arun R
2025-10-15 4:07 ` [PATCH 02/25] drm/i915/cx0: Change register bit naming for powerdown values Suraj Kandpal
2025-10-22 8:01 ` Murthy, Arun R
2025-10-15 4:07 ` Suraj Kandpal [this message]
2025-10-22 8:41 ` [PATCH 03/25] drm/i915/ltphy: Phy lane reset for LT Phy Murthy, Arun R
2025-10-22 9:01 ` Kandpal, Suraj
2025-10-15 4:07 ` [PATCH 04/25] drm/i915/ltphy: Program sequence for PORT_CLOCK_CTL " Suraj Kandpal
2025-10-22 8:49 ` Murthy, Arun R
2025-10-22 8:58 ` Kandpal, Suraj
2025-10-22 9:06 ` Murthy, Arun R
2025-10-15 4:07 ` [PATCH 05/25] drm/i915/ltphy: Add a wrapper for LT Phy powerdown change sequence Suraj Kandpal
2025-10-22 9:13 ` Murthy, Arun R
2025-10-15 4:07 ` [PATCH 06/25] drm/i915/ltphy: Read PHY_VDR_0_CONFIG register Suraj Kandpal
2025-10-23 7:29 ` Murthy, Arun R
2025-10-15 4:07 ` [PATCH 07/25] drm/i915/ltphy: Add LT Phy Programming recipe tables Suraj Kandpal
2025-10-23 7:36 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 08/25] drm/i915/ltphy: Program the VDR PLL registers for LT PHY Suraj Kandpal
2025-10-23 7:40 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 09/25] drm/i915/ltphy: Update the ltpll config table value for eDP Suraj Kandpal
2025-10-23 7:42 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 10/25] drm/i915/ltphy: Enable SSC during port clock programming Suraj Kandpal
2025-10-23 7:49 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 11/25] drm/i915/ltphy: Add function to calculate LT PHY port clock Suraj Kandpal
2025-10-15 4:08 ` [PATCH 12/25] drm/i915/ltphy: Program the P2P Transaction flow for LT Phy Suraj Kandpal
2025-10-23 8:18 ` Murthy, Arun R
2025-10-23 9:24 ` Kandpal, Suraj
2025-10-23 9:32 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 13/25] drm/i915/ltphy: Program the rest of the PORT_CLOCK_CTL steps Suraj Kandpal
2025-10-23 8:27 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 14/25] drm/i915/ltphy: Program the rest of the LT Phy Enable sequence Suraj Kandpal
2025-10-23 8:32 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 15/25] drm/i915/ltphy: Program LT Phy Non-TBT PLL disable sequence Suraj Kandpal
2025-10-23 8:40 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 16/25] drm/i915/ltphy: Hook up LT Phy Enable & Disable sequences Suraj Kandpal
2025-10-23 8:43 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 17/25] drm/i915/ddi: Define LT Phy Swing tables Suraj Kandpal
2025-10-23 9:33 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 18/25] drm/i915/ltphy: Program LT Phy Voltage Swing Suraj Kandpal
2025-10-24 6:39 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 19/25] drm/i915/ltphy: Enable/Disable Tx after Non TBT Enable sequence Suraj Kandpal
2025-10-24 7:00 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 20/25] drm/i915/ltphy: Define the LT Phy state compare function Suraj Kandpal
2025-10-24 7:03 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 21/25] drm/i915/ltphy: Define function to readout LT Phy PLL state Suraj Kandpal
2025-10-24 7:14 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 22/25] drm/i915/ltphy: Define LT PHY PLL state verify function Suraj Kandpal
2025-10-24 7:26 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 23/25] drm/i915/display: Aux Enable and Display powerwell timeouts Suraj Kandpal
2025-10-24 7:32 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 24/25] drm/i915/ltphy: Modify the step that need to by skipped Suraj Kandpal
2025-10-24 7:33 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 25/25] drm/i915/ltphy: Implement HDMI Algo for Pll state Suraj Kandpal
2025-10-15 4:22 ` ✗ CI.checkpatch: warning for Enable LT PHY Patchwork
2025-10-15 4:23 ` ✓ CI.KUnit: success " Patchwork
2025-10-15 4:38 ` ✗ CI.checksparse: warning " Patchwork
2025-10-15 5:00 ` ✓ Xe.CI.BAT: success " Patchwork
2025-10-15 14:28 ` ✗ Xe.CI.Full: failure " Patchwork
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251015040817.3431297-4-suraj.kandpal@intel.com \
--to=suraj.kandpal@intel.com \
--cc=ankit.k.nautiyal@intel.com \
--cc=arun.r.murthy@intel.com \
--cc=gustavo.sousa@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=intel-xe@lists.freedesktop.org \
--cc=lucas.demarchi@intel.com \
--cc=uma.shankar@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox