From: "Murthy, Arun R" <arun.r.murthy@intel.com>
To: Suraj Kandpal <suraj.kandpal@intel.com>,
<intel-xe@lists.freedesktop.org>,
<intel-gfx@lists.freedesktop.org>
Cc: <ankit.k.nautiyal@intel.com>, <uma.shankar@intel.com>,
<gustavo.sousa@intel.com>, <lucas.demarchi@intel.com>
Subject: Re: [PATCH 12/25] drm/i915/ltphy: Program the P2P Transaction flow for LT Phy
Date: Thu, 23 Oct 2025 13:48:21 +0530 [thread overview]
Message-ID: <9f7466b5-e5e7-4603-b564-0ef7f073d2c7@intel.com> (raw)
In-Reply-To: <20251015040817.3431297-13-suraj.kandpal@intel.com>
On 15-10-2025 09:38, Suraj Kandpal wrote:
> Program the LT PHY P2P transaction which uses P2M cycle to get
> get data fro Phy when it is ready and then go read the MAC register
> from the MAC address space.
>
> Bspec: 68966, 74497, 74483, 74500
> Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
> ---
> drivers/gpu/drm/i915/display/intel_cx0_phy.c | 10 +-
> drivers/gpu/drm/i915/display/intel_cx0_phy.h | 5 +
> .../gpu/drm/i915/display/intel_cx0_phy_regs.h | 1 +
> drivers/gpu/drm/i915/display/intel_lt_phy.c | 115 ++++++++++++++++++
> .../gpu/drm/i915/display/intel_lt_phy_regs.h | 15 +++
> 5 files changed, 141 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_cx0_phy.c b/drivers/gpu/drm/i915/display/intel_cx0_phy.c
> index c50233f17bc6..b060a5007921 100644
> --- a/drivers/gpu/drm/i915/display/intel_cx0_phy.c
> +++ b/drivers/gpu/drm/i915/display/intel_cx0_phy.c
> @@ -125,8 +125,8 @@ static void intel_cx0_phy_transaction_end(struct intel_encoder *encoder, intel_w
> intel_display_power_put(display, POWER_DOMAIN_DC_OFF, wakeref);
> }
>
> -static void intel_clear_response_ready_flag(struct intel_encoder *encoder,
> - int lane)
> +void intel_clear_response_ready_flag(struct intel_encoder *encoder,
> + int lane)
> {
> struct intel_display *display = to_intel_display(encoder);
>
> @@ -135,7 +135,7 @@ static void intel_clear_response_ready_flag(struct intel_encoder *encoder,
> 0, XELPDP_PORT_P2M_RESPONSE_READY | XELPDP_PORT_P2M_ERROR_SET);
> }
>
> -static void intel_cx0_bus_reset(struct intel_encoder *encoder, int lane)
> +void intel_cx0_bus_reset(struct intel_encoder *encoder, int lane)
> {
> struct intel_display *display = to_intel_display(encoder);
> enum port port = encoder->port;
> @@ -156,8 +156,8 @@ static void intel_cx0_bus_reset(struct intel_encoder *encoder, int lane)
> intel_clear_response_ready_flag(encoder, lane);
> }
>
> -static int intel_cx0_wait_for_ack(struct intel_encoder *encoder,
> - int command, int lane, u32 *val)
> +int intel_cx0_wait_for_ack(struct intel_encoder *encoder,
> + int command, int lane, u32 *val)
> {
> struct intel_display *display = to_intel_display(encoder);
> enum port port = encoder->port;
> diff --git a/drivers/gpu/drm/i915/display/intel_cx0_phy.h b/drivers/gpu/drm/i915/display/intel_cx0_phy.h
> index 283be36d5dff..a5446686b23b 100644
> --- a/drivers/gpu/drm/i915/display/intel_cx0_phy.h
> +++ b/drivers/gpu/drm/i915/display/intel_cx0_phy.h
> @@ -22,6 +22,8 @@ struct intel_display;
> struct intel_encoder;
> struct intel_hdmi;
>
> +void intel_clear_response_ready_flag(struct intel_encoder *encoder,
> + int lane);
> bool intel_encoder_is_c10phy(struct intel_encoder *encoder);
> void intel_mtl_pll_enable(struct intel_encoder *encoder,
> const struct intel_crtc_state *crtc_state);
> @@ -53,6 +55,9 @@ u8 intel_cx0_read(struct intel_encoder *encoder,
> u8 lane_mask, u16 addr);
> void intel_cx0_write(struct intel_encoder *encoder,
> u8 lane_mask, u16 addr, u8 data, bool committed);
> +int intel_cx0_wait_for_ack(struct intel_encoder *encoder,
> + int command, int lane, u32 *val);
> +void intel_cx0_bus_reset(struct intel_encoder *encoder, int lane);
> int intel_mtl_tbt_calc_port_clock(struct intel_encoder *encoder);
> void intel_cx0_pll_power_save_wa(struct intel_display *display);
> void intel_lnl_mac_transmit_lfps(struct intel_encoder *encoder,
> diff --git a/drivers/gpu/drm/i915/display/intel_cx0_phy_regs.h b/drivers/gpu/drm/i915/display/intel_cx0_phy_regs.h
> index 114f6b2113db..cb2ab8442aa1 100644
> --- a/drivers/gpu/drm/i915/display/intel_cx0_phy_regs.h
> +++ b/drivers/gpu/drm/i915/display/intel_cx0_phy_regs.h
> @@ -50,6 +50,7 @@
> #define XELPDP_PORT_M2P_COMMAND_WRITE_UNCOMMITTED REG_FIELD_PREP(XELPDP_PORT_M2P_COMMAND_TYPE_MASK, 0x1)
> #define XELPDP_PORT_M2P_COMMAND_WRITE_COMMITTED REG_FIELD_PREP(XELPDP_PORT_M2P_COMMAND_TYPE_MASK, 0x2)
> #define XELPDP_PORT_M2P_COMMAND_READ REG_FIELD_PREP(XELPDP_PORT_M2P_COMMAND_TYPE_MASK, 0x3)
> +#define XELPDP_PORT_P2P_TRANSACTION_PENDING REG_BIT(24)
> #define XELPDP_PORT_M2P_DATA_MASK REG_GENMASK(23, 16)
> #define XELPDP_PORT_M2P_DATA(val) REG_FIELD_PREP(XELPDP_PORT_M2P_DATA_MASK, val)
> #define XELPDP_PORT_M2P_TRANSACTION_RESET REG_BIT(15)
> diff --git a/drivers/gpu/drm/i915/display/intel_lt_phy.c b/drivers/gpu/drm/i915/display/intel_lt_phy.c
> index 3aa8b3b345d3..32a5a60fe92f 100644
> --- a/drivers/gpu/drm/i915/display/intel_lt_phy.c
> +++ b/drivers/gpu/drm/i915/display/intel_lt_phy.c
> @@ -19,6 +19,10 @@
> #include "intel_psr.h"
> #include "intel_tc.h"
>
> +#define for_each_lt_phy_lane_in_mask(__lane_mask, __lane) \
> + for ((__lane) = 0; (__lane) < 2; (__lane)++) \
> + for_each_if((__lane_mask) & BIT(__lane))
> +
> #define INTEL_LT_PHY_LANE0 BIT(0)
> #define INTEL_LT_PHY_LANE1 BIT(1)
> #define INTEL_LT_PHY_BOTH_LANES (INTEL_LT_PHY_LANE1 |\
> @@ -999,6 +1003,113 @@ static void intel_lt_phy_write(struct intel_encoder *encoder,
> intel_cx0_write(encoder, lane_mask, addr, data, committed);
> }
>
> +static void intel_lt_phy_clear_status_p2p(struct intel_encoder *encoder,
> + int lane)
> +{
> + struct intel_display *display = to_intel_display(encoder);
> +
> + intel_de_rmw(display,
> + XE3PLPD_PORT_P2M_MSGBUS_STATUS_P2P(encoder->port, lane),
> + XELPDP_PORT_P2M_RESPONSE_READY, 0);
> +}
> +
> +static void
> +assert_dc_off(struct intel_display *display)
> +{
> + bool enabled;
> +
> + enabled = intel_display_power_is_enabled(display, POWER_DOMAIN_DC_OFF);
> + drm_WARN_ON(display->drm, !enabled);
> +}
> +
> +static int __intel_lt_phy_p2p_write_once(struct intel_encoder *encoder,
> + int lane, u16 addr, u8 data,
> + i915_reg_t mac_reg_addr,
> + u8 expected_mac_val)
> +{
> + struct intel_display *display = to_intel_display(encoder);
> + enum port port = encoder->port;
> + enum phy phy = intel_encoder_to_phy(encoder);
> + int ack;
> + u32 val;
> +
> + if (intel_de_wait_for_clear(display, XELPDP_PORT_M2P_MSGBUS_CTL(display, port, lane),
> + XELPDP_PORT_P2P_TRANSACTION_PENDING,
> + XELPDP_MSGBUS_TIMEOUT_SLOW)) {
> + drm_dbg_kms(display->drm,
> + "PHY %c Timeout waiting for previous transaction to complete. Resetting bus.\n",
> + phy_name(phy));
> + intel_cx0_bus_reset(encoder, lane);
> + return -ETIMEDOUT;
> + }
> +
> + intel_de_rmw(display, XELPDP_PORT_P2M_MSGBUS_STATUS(display, port, lane), 0, 0);
> +
> + intel_de_write(display, XELPDP_PORT_M2P_MSGBUS_CTL(display, port, lane),
> + XELPDP_PORT_P2P_TRANSACTION_PENDING |
> + XELPDP_PORT_M2P_COMMAND_WRITE_COMMITTED |
> + XELPDP_PORT_M2P_DATA(data) |
> + XELPDP_PORT_M2P_ADDRESS(addr));
> +
> + ack = intel_cx0_wait_for_ack(encoder, XELPDP_PORT_P2M_COMMAND_WRITE_ACK, lane, &val);
> + if (ack < 0)
> + return ack;
> +
> + if (val & XELPDP_PORT_P2M_ERROR_SET) {
> + drm_dbg_kms(display->drm,
> + "PHY %c Error occurred during P2P write command. Status: 0x%x\n",
> + phy_name(phy), val);
> + intel_lt_phy_clear_status_p2p(encoder, lane);
> + intel_cx0_bus_reset(encoder, lane);
> + return -EINVAL;
> + }
> +
> + /*
> + * This needs to be added to give PHY time to set everything up this was a requirement
> + * to get the display up and running.
> + */
> + udelay(150);
How was this delay value derived?
Thanks and Regards,
Arun R Murthy
-------------------
> + intel_clear_response_ready_flag(encoder, lane);
> + intel_lt_phy_clear_status_p2p(encoder, lane);
> +
> + return 0;
> +}
> +
> +static void __intel_lt_phy_p2p_write(struct intel_encoder *encoder,
> + int lane, u16 addr, u8 data,
> + i915_reg_t mac_reg_addr,
> + u8 expected_mac_val)
> +{
> + struct intel_display *display = to_intel_display(encoder);
> + enum phy phy = intel_encoder_to_phy(encoder);
> + int i, status;
> +
> + assert_dc_off(display);
> +
> + /* 3 tries is assumed to be enough to write successfully */
> + for (i = 0; i < 3; i++) {
> + status = __intel_lt_phy_p2p_write_once(encoder, lane, addr, data, mac_reg_addr,
> + expected_mac_val);
> +
> + if (status == 0)
> + return;
> + }
> +
> + drm_err_once(display->drm,
> + "PHY %c P2P Write %04x failed after %d retries.\n", phy_name(phy), addr, i);
> +}
> +
> +static void intel_lt_phy_p2p_write(struct intel_encoder *encoder,
> + u8 lane_mask, u16 addr, u8 data,
> + i915_reg_t mac_reg_addr,
> + u8 expected_mac_val)
> +{
> + int lane;
> +
> + for_each_lt_phy_lane_in_mask(lane_mask, lane)
> + __intel_lt_phy_p2p_write(encoder, lane, addr, data, mac_reg_addr, expected_mac_val);
> +}
> +
> static void
> intel_lt_phy_setup_powerdown(struct intel_encoder *encoder, u8 lane_count)
> {
> @@ -1417,6 +1528,10 @@ void intel_lt_phy_pll_enable(struct intel_encoder *encoder,
> * register at offset 0xC00 for Owned PHY Lanes*.
> */
> /* 6.3. Clear P2P transaction Ready bit. */
> + intel_lt_phy_p2p_write(encoder, owned_lane_mask, LT_PHY_RATE_UPDATE,
> + LT_PHY_RATE_CONTROL_VDR_UPDATE, LT_PHY_MAC_VDR,
> + LT_PHY_PCLKIN_GATE);
> +
> /* 7. Program PORT_CLOCK_CTL[PCLK PLL Request LN0] = 0. */
> /* 8. Poll for PORT_CLOCK_CTL[PCLK PLL Ack LN0]= 0. */
> /*
> diff --git a/drivers/gpu/drm/i915/display/intel_lt_phy_regs.h b/drivers/gpu/drm/i915/display/intel_lt_phy_regs.h
> index a4aa2a3e0425..5fb4331c387f 100644
> --- a/drivers/gpu/drm/i915/display/intel_lt_phy_regs.h
> +++ b/drivers/gpu/drm/i915/display/intel_lt_phy_regs.h
> @@ -9,12 +9,17 @@
> #include "i915_reg_defs.h"
> #include "intel_display_limits.h"
>
> +#define XE3PLPD_MSGBUS_TIMEOUT_FAST_US 500
> #define XE3PLPD_MACCLK_TURNON_LATENCY_MS 1
> #define XE3PLPD_MACCLK_TURNON_LATENCY_US 21
> #define XE3PLPD_RATE_CALIB_DONE_LATENCY_US 50
> #define XE3PLPD_RESET_START_LATENCY_US 10
> #define XE3PLPD_RESET_END_LATENCY_US 200
>
> +/* LT Phy MAC Register */
> +#define LT_PHY_MAC_VDR _MMIO(0xC00)
> +#define LT_PHY_PCLKIN_GATE REG_BIT8(0)
> +
> /* LT Phy Vendor Register */
> #define LT_PHY_VDR_0_CONFIG 0xC02
> #define LT_PHY_VDR_DP_PLL_ENABLE REG_BIT(7)
> @@ -29,6 +34,7 @@
> #define LT_PHY_VDR_X_DATAY(idx, y) ((0xC06 + (3 - (y))) + 0x6 * (idx))
>
> #define LT_PHY_RATE_UPDATE 0xCC4
> +#define LT_PHY_RATE_CONTROL_VDR_UPDATE REG_BIT8(0)
>
> #define _XE3PLPD_PORT_BUF_CTL5(idx) _MMIO(_PICK_EVEN_2RANGES(idx, PORT_TC1, \
> _XELPDP_PORT_BUF_CTL1_LN0_A, \
> @@ -41,4 +47,13 @@
> #define XE3PLPD_MACCLK_RATE_MASK REG_GENMASK(4, 0)
> #define XE3PLPD_MACCLK_RATE_DEF REG_FIELD_PREP(XE3PLPD_MACCLK_RATE_MASK, 0x1F)
>
> +#define _XE3PLPD_PORT_P2M_MSGBUS_STATUS_P2P(idx, lane) _MMIO(_PICK_EVEN_2RANGES(idx, PORT_TC1, \
> + _XELPDP_PORT_M2P_MSGBUS_CTL_LN0_A, \
> + _XELPDP_PORT_M2P_MSGBUS_CTL_LN0_B, \
> + _XELPDP_PORT_M2P_MSGBUS_CTL_LN0_USBC1, \
> + _XELPDP_PORT_M2P_MSGBUS_CTL_LN0_USBC2) \
> + + 0x60 + (lane) * 0x4)
> +#define XE3PLPD_PORT_P2M_MSGBUS_STATUS_P2P(port, lane) _XE3PLPD_PORT_P2M_MSGBUS_STATUS_P2P(__xe2lpd_port_idx(port), \
> + lane)
> +#define XE3LPD_PORT_P2M_ADDR_MASK REG_GENMASK(11, 0)
> #endif /* __INTEL_LT_PHY_REGS_H__ */
next prev parent reply other threads:[~2025-10-23 8:18 UTC|newest]
Thread overview: 61+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-15 4:07 [PATCH 00/25] Enable LT PHY Suraj Kandpal
2025-10-15 4:07 ` [PATCH 01/25] drm/i915/ltphy: Add LT Phy related VDR and Pipe Registers Suraj Kandpal
2025-10-20 11:10 ` Jani Nikula
2025-10-22 4:05 ` Kandpal, Suraj
2025-10-22 7:57 ` Murthy, Arun R
2025-10-15 4:07 ` [PATCH 02/25] drm/i915/cx0: Change register bit naming for powerdown values Suraj Kandpal
2025-10-22 8:01 ` Murthy, Arun R
2025-10-15 4:07 ` [PATCH 03/25] drm/i915/ltphy: Phy lane reset for LT Phy Suraj Kandpal
2025-10-22 8:41 ` Murthy, Arun R
2025-10-22 9:01 ` Kandpal, Suraj
2025-10-15 4:07 ` [PATCH 04/25] drm/i915/ltphy: Program sequence for PORT_CLOCK_CTL " Suraj Kandpal
2025-10-22 8:49 ` Murthy, Arun R
2025-10-22 8:58 ` Kandpal, Suraj
2025-10-22 9:06 ` Murthy, Arun R
2025-10-15 4:07 ` [PATCH 05/25] drm/i915/ltphy: Add a wrapper for LT Phy powerdown change sequence Suraj Kandpal
2025-10-22 9:13 ` Murthy, Arun R
2025-10-15 4:07 ` [PATCH 06/25] drm/i915/ltphy: Read PHY_VDR_0_CONFIG register Suraj Kandpal
2025-10-23 7:29 ` Murthy, Arun R
2025-10-15 4:07 ` [PATCH 07/25] drm/i915/ltphy: Add LT Phy Programming recipe tables Suraj Kandpal
2025-10-23 7:36 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 08/25] drm/i915/ltphy: Program the VDR PLL registers for LT PHY Suraj Kandpal
2025-10-23 7:40 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 09/25] drm/i915/ltphy: Update the ltpll config table value for eDP Suraj Kandpal
2025-10-23 7:42 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 10/25] drm/i915/ltphy: Enable SSC during port clock programming Suraj Kandpal
2025-10-23 7:49 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 11/25] drm/i915/ltphy: Add function to calculate LT PHY port clock Suraj Kandpal
2025-10-15 4:08 ` [PATCH 12/25] drm/i915/ltphy: Program the P2P Transaction flow for LT Phy Suraj Kandpal
2025-10-23 8:18 ` Murthy, Arun R [this message]
2025-10-23 9:24 ` Kandpal, Suraj
2025-10-23 9:32 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 13/25] drm/i915/ltphy: Program the rest of the PORT_CLOCK_CTL steps Suraj Kandpal
2025-10-23 8:27 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 14/25] drm/i915/ltphy: Program the rest of the LT Phy Enable sequence Suraj Kandpal
2025-10-23 8:32 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 15/25] drm/i915/ltphy: Program LT Phy Non-TBT PLL disable sequence Suraj Kandpal
2025-10-23 8:40 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 16/25] drm/i915/ltphy: Hook up LT Phy Enable & Disable sequences Suraj Kandpal
2025-10-23 8:43 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 17/25] drm/i915/ddi: Define LT Phy Swing tables Suraj Kandpal
2025-10-23 9:33 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 18/25] drm/i915/ltphy: Program LT Phy Voltage Swing Suraj Kandpal
2025-10-24 6:39 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 19/25] drm/i915/ltphy: Enable/Disable Tx after Non TBT Enable sequence Suraj Kandpal
2025-10-24 7:00 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 20/25] drm/i915/ltphy: Define the LT Phy state compare function Suraj Kandpal
2025-10-24 7:03 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 21/25] drm/i915/ltphy: Define function to readout LT Phy PLL state Suraj Kandpal
2025-10-24 7:14 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 22/25] drm/i915/ltphy: Define LT PHY PLL state verify function Suraj Kandpal
2025-10-24 7:26 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 23/25] drm/i915/display: Aux Enable and Display powerwell timeouts Suraj Kandpal
2025-10-24 7:32 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 24/25] drm/i915/ltphy: Modify the step that need to by skipped Suraj Kandpal
2025-10-24 7:33 ` Murthy, Arun R
2025-10-15 4:08 ` [PATCH 25/25] drm/i915/ltphy: Implement HDMI Algo for Pll state Suraj Kandpal
2025-10-15 4:22 ` ✗ CI.checkpatch: warning for Enable LT PHY Patchwork
2025-10-15 4:23 ` ✓ CI.KUnit: success " Patchwork
2025-10-15 4:38 ` ✗ CI.checksparse: warning " Patchwork
2025-10-15 5:00 ` ✓ Xe.CI.BAT: success " Patchwork
2025-10-15 14:28 ` ✗ Xe.CI.Full: failure " Patchwork
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=9f7466b5-e5e7-4603-b564-0ef7f073d2c7@intel.com \
--to=arun.r.murthy@intel.com \
--cc=ankit.k.nautiyal@intel.com \
--cc=gustavo.sousa@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=intel-xe@lists.freedesktop.org \
--cc=lucas.demarchi@intel.com \
--cc=suraj.kandpal@intel.com \
--cc=uma.shankar@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox